Search Documents

By W. F. Rochow, W. C. Burke

Numerous designs of linings and accessories, including dams, lifters, and heat exchangers, contribute greatly to kiln efficiencies. Greater conductivity is achieved with basic brick than with fireclay and high-alumina refractories, depending largely upon the use of steel plates in radial joints between adjacent brick to increase heat transfer through the lining. Refractory lifters expose all portions of the load to radiant or convective heat and raise some portions to higher temperatures by cascading the load down through the path of the hot gases.

Jan 3, 1955

By D. Vogt

South African underground hard rock mines are typically managed using measurements made daily, weekly or even monthly of key parameters such as face advance, readiness to blast, blast success, temperature or dust levels. Health, safety and productivity can all be greatly improved if a real-time measurement system can inform decision making. To enable this vision of widespread sensing, communication and decision support, CSIR has developed an open standard architecture for communication of sensor data, and a reference implementation using that standard. The standard, called AziSA, meaning ?to inform? in isiZulu, will allow any device that complies with it to join any network that supports it. The standard is designed for South African gold and platinum mines. To be practical in a typical Bushveld platinum mine, a real-time sensor system needs to be robust, reliable and cheap: ?Sensors are equipped with power sources that will last as long as the sensor is required. In effect, sensors need to be disposable: cheap enough not to warrant repair if they break. ?Communication in the stope is wireless, to avoid there liability problems associated with wire connections. For example, wires to sensors in the face area are unlikely to survive blasting. ?To get information out of the stope, the power line to the scraper winch is used as a communications link. Unlike a separate communications link, the power line will be repaired if damaged, because of its importance to production. ?Outside the stope, communications are transferred onto the mine communication infrastructure. To succeed as a management system, the next key element is the use of software decision support tools that will analyse masses of real-time data to extract key parameters and trends for decision makers. A range of sensors has been developed, including commercial sensors that have had wireless adapters added to make them AziSA compliant, and bespoke sensors that provide low cost sensing of typical mining parameters. An important parameter in any sensor network is the location of the sensor. This has to be easy and cheap to establish, so a tool has been developed to locate sensors in the confines of a stope, using ultrasonic and radio techniques. Once sensors are installed and located, they associate their location to all data that they produce. All the data from the system are captured at surface in a flexible database that can be queried by any application that requires data of any kind. It is simple to program alerts, and for actions to be associated with alerts. The use of wireless in stope also allows for communication from surface to the stope, or from stope to stope. The first implementation of an AziSA compliant system is being installed as part of the Mine Health and Safety Council funded rockfall elimination project. The design is discussed, and a future application for a platinum mine is considered.

Jan 1, 2009

By Brian Gar Wingfield

"The introduction of the QuarryMan laser profile system in 1987, along with the development of the corresponding 3-D software, gave a qualified operator pertinent information about dimensions of quarry highwalls, pattern and hole loading design, stockpile profiles, etc . . . Attributes helpful for this endeavor included surveying, computer, and blasting knowledge. Since not all operators had theseskills, a simpler model, the QuarryAce, was designed to look a t highwall dimensions in 2-D view . Al though less sophisticated than the QuarryMan instrument and its software, it is simpler to instruct in its use and has the ability to determine burdens at different depth levels . An in-house user f r i e n d l y computer program was designed to utilize QuarryAce depth vs. burden data . This program was created to enable laser and computer novices to generate information useful to the everyday blaster."

Jan 1, 1992

Recovery of Fine Gold Particles from Philippine Gold Deposits by Enhanced Gravity Concentration and Flotation The objective of the study is to determine the applicability of enhanced gravity concentration (EGC) and flotation for gold recovery. While gravity concentration methods have long been applied to gold ores, especially to free-milling types that requires minimal beneficiation, flotation for gold recovery has not yet taken hold as a major operation in the Philippine setting. In this study, the application of EGC and flotation for gold is applied and compared to the existing methods for gold recovery. Two samples, with assays of 7.315 and 5.333 g Au/MT (samples 1 and 2, respectively) are used for this study. These samples are subjected to mineralogical studies and is found to have a gold-particle size ranging 10 to 200 microns. To verify the separation size, the mesh-of-grind (MOG) is used as the primary parameter for experimentation. Initially, the samples are stage-crushed, ground, and subjected to EGC using a Falcon SB40 Concentrator. Based on the results, the two samples showed that recovery increases with a finer MOG. The ratio of concentration (K) decreases with a finer MOG. This shows that there should be sufficient liberation of the gold values for EGC to be effective. The effect of the enhancement is to pronounce the difference in specific gravity of the minerals, promoting better separation. This is validated by the high recovery values of 86.97 per cent and 98.73 per cent exhibited respectively for samples 1 and 2 (at 54 microns). For the flotation runs, sample 2 with an average particle size of 80 per cent passing 74 microns is examined using thiocarbamate-based collectors for roughing and subsequently exhibited a recovery of 96.32 per cent. At this point, the concentration ratio (K) is noted as an important efficiency indicator for flotation process since it yielded a very low-mass and high-metal content concentrate.

Sep 13, 2010

By J White

The Eyre Peninsula (EP) has been known for its iron ore for more than a century. Edward John Eyre noted the ironstone outcrop at what is now Iron Knob in the 19th century. Sir Douglas Mawson visited and reported on the geology of the lower EP in 1906, noting the widespread presence of iron stone and the likelihood of copper being associated with the iron stone. Despite this knowledge there has been only one successful iron ore mining region developed on the EP and that is Iron Knob and the Middleback Ranges which have been mined continuously since 1899. The Middleback Ranges can justly lay claim to be birth place of the Australian iron ore and steel industries.The discovery of large scale haematite resources in Western Australia meant that there was no need to seek out iron ore that needed benefi ciation. The low price of iron ore precluded further development of the EP and many other areas in Australia and overseas. This situation changed rapidly in the mid-2000s with the emergence of China as the world’s industrial power house and the soaring demand and price for many resources including iron ore. This triggered a flurry of activity across Australia and led to the rapid exploration and drives to develop the EP iron ore. A brief examination of the magnetic maps of the EP shows the wide spread presence of magnetite and associated smaller haematite deposits. A closer look reveals the magnetite deposits to vary in formation style and host rock lithology as well as being significantly altered by regional metamorphism. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011

By Roy M. Schnabel

The Fashion Island Boulevard Bridge over the Marina Lagoon in San Mateo, California is an eight span precast, prestressed concrete girder bridge. It is approximately 495 feet in length and 61 feet in width. It is supported on 36" diameter octagonal, hollow precast-prestressed concrete pile columns. The bridge was constructed in 1968 and suffered considerable damage during the Loma Prieta Earthquake in 1989. A damage survey report prepared by the State's Office of Emergency Services (OES) recorded that sixteen of the twenty-one pile-columns sustained heavy to moderate damage from the Loma Prieta Earthquake. The damage consisted of cracking and spalling at the tops of the pile-columns. Spalls at the most heavily damaged columns exposed the prestressing strands and confinement reinforcing which also showed signs of corrosion.

Jan 1, 1993

Gangue-cemented paste backfill (GCPB), is a well-established green mining technology and significantly improves the recovery rate of mineral resources, prevents mine dynamic disasters, reduces surface subsidence, and consumes a considerable amount of solid waste. The addition of an early strength agent as an additive in cement-based materials provides several security, technical, and economic advantages. In this study, the early strength agent on the early age (3, 7 and 28 days) strength of GCPB is evaluated experimentally. The GCPB specimens have an initial sodium sulfate early strength agent concentration of 0%, 1%, 2%, 3%, and 4%, and the obtained samples were analyzed by testing for uniaxial compressive strength (UCS) and scanning electron microscopy (SEM). The test results show that the UCS of the GCPB specimens with sodium sulfate is much higher than that of the blank specimens. When cured for 3 days and 7 days, the strength of GCPB with 2% sodium sulfate increased the most, by 131% and 116% respectively. When cured for 28 days, the strength of GCPB with 1% sodium sulfate increased by 135%. Scanning electron microscopy (SEM) results showed that the GCPB with 1% and 2% sodium sulfate had better internal structure compactness, thicker acicular crystals, and more flocs. As a kind of early strength agent, sodium sulfate can react with calcium hydroxide to generate calcium dihydrate sulfate and then react with calcium aluminate; the hydration product (C3A) quickly generates calcium sulfoaluminate hydrate (AFt) needle-shaped crystals, forming an early skeleton and improving the early strength.

Jan 7, 2020

By Dianyin Liang, Hongxiang Ran, Xiaoming Wang, Xiaoou Xia

"This paper presents a new magnetic separator, which can be applied to increase the grade of fine magnetite ore feeding of ball mill. This innovative equipment possesses a rotating magnetic system and has a magnetic field of rapid polarity change which can strengthen the destruction of magnetic agglomerations and the dispersion of minerals to improve the quality of separation. Now this type separators have been successfully applied in several large concentrating plants such as Shuichang Iron Mine under Shouang Mining Company in China. Finally, this paper outlines practical results focused on feed grade and tailing yield, the results are showing that the quality of feeding can be improve tremendously. Hence, a new generator of rotating magnetic field has been paved. INTRODUCTION Jidong region in China is the important origin of iron ore, the characteristics of the iron ore in this region is low grade and complex, the iron mine discharges fine powder tailings reaches tens of millions of tons each year, in the wind action easy to form sand, this poses a threat to the atmosphere environment of Beijing. In order to reduce the mixing of large amount of useless ore and reduce the energy consumption of mill operation, a high efficiency pregrinding equipment is needed. Rotating magnetic field separator (RMS) is an advanced equipment, the main advantage of RMS is the significant reduction in particle entrapment and can easily break magnetic agglomeration. This reduction is so significant that RMS is capable of operating very close to theoritical limit for separator precision and can increace efficiency in selection process.Some expenrimental work on dry rotating magnetic field separation has been carried out in July 1998 in the company Ka Pty Ltd, then in 2008 BGRIMM developed industrial separation XCTG0816 in Shandong province . The wet RMS was researched in1960s in Former Soviet Union and the first industrial equipment was developed by BGRIMM in 1970s,then in 1990s wet RMS was applied in Ansteel group corporation. In 2017,6 units large wet RMS (SXCT1230)which were the largest RMS was applied in Sichuan province. No matter wet RMS and dry RMS, although they are used in differenct applications, they have some common research.in addition ,they all have good use effect."

Jan 1, 2018

The use of comparative sampling methods during the evaluation of the tin-copper deposits at Cleveland mine yielded closely checking average results from groove, channel, AXT split diamond drill core, and bulk sampling for both tin and copper content of the ore.The weighted mean tin and copper grades and values for the groove, channel, and split core samples showed small percentage differences from bulk sample results, and the F-ratio test for single population origin of the four types of samples was accepted at the 99· 5 per cent level of confidence.These results indicate that grade estimates based on the assays from AXT split diamond drill core and/or groove samples would be reliable within practical limits.

Jan 1, 1968

Determine the advantages and operational limitations of water-let-assisted cutting used with mining equipment. Approach The Bureau of Mines con-ducted a research study to evaluate water-Jet-assisted cutting both in the laboratory and in underground mines. Earlier research on water-jet-assist was limited to laboratory studies where bit speeds and penetration depths were very low and large cutting force reductions were reported. For the past years, research by the Bureau of Mines and others has been concerned with the application of water-jet-assisted cutting under more realistic mining conditions. Study Results Water-jet-assisted cutting employs a mechanical cut-ting bit combined with a moderate to high-pressure water jet directed just in front of the bit tip to assist in the cutting process. Recent Bureau findings show that the addition of the water jet to the cutting bit can improve cutting in harder materials, significantly reduce respirable dust and bit wear, and increase product size. Some of these findings are presented as follows.

Jan 1, 1987

By Kiichiro Hayashi

"Indonesia is one of the world leaders in palm oil production. Palm oil industry is an industry to be considered when it comes to environmental impacts. This paper utilizes three step approaches. First, a material flow analysis of palm oil related industry was conducted in Indonesia. Second, a factory visit survey was conducted for getting information on environmental impacts of plantation and CPO mills. Third, a LCA study was made for a model Indonesian CPO mill in several bio-waste treatment options. Main findings were that, first; over 70% of FFB was bio-wastes generated from CPO mills. Second, some mills introduced a zero emission bio-waste policy. However, untreated bio-wastes in the zero emission policy, such as, CH4 from POME ponds, may have potential to reduce more impacts on the environment. Introduction Indonesia is one of the world leaders in palm oil production with approximately 12.4 million tons of crude palm oil (CPO) production in 2005 and with the plantation area 5.6 million ha spreading out in 19 provinces [10]. The expansion of palm oil cultivation in Indonesia and its export oriented industry heavily relies on the strong world market demand for food. Currently, there are 320 CPO industries in Indonesia [10]. These include plantations and palm oil related factories. Among them, there are six biggest players in CPO business in Indonesia: PT. Perkebunan Nusantara (PTPN) consisting of 9 PTPN, Sinar Mas, Raja Garuda Mas, Astra Agro Lestari, Minamas Plantation and Indofood. They are managing more than 50% of plantation estate in Indonesia and are leading the Indonesian palm oil business.Palm oil industry is an industry to be considered when it comes to environmental impacts. Unfortunately, there is not so much available information related to the performance of each CPO on environmental impacts. There are reports which provide information on environmental impacts of CPO mills in South East Asian countries, but are limited to, for instance, Thailand’s cases [4 and 5] and Malaysia’s cases [1, 3, 6, 7, 9, 11 and 12]. On the other hand, similar studies on the Indonesian’s case are not well established in academic literatures. And also there is limitation on Indonesian palm oil industrial information from plantation to consumption and disposal in academic articles. There is no literature related to material flow analysis focusing on the whole Indonesian palm oil related industry. One way to describe and present the environmental impacts is through a life cycle assessment (LCA). The LCA could be used to estimate the impacts of CPO production including the stages of plantation, transportation and milling [5, 8 and 11]. However, studies on Indonesian CPO production process were not well established in academic articles. The purpose of this paper is thus to clarify environmental impacts of palm oil industry in Indonesia especially by focusing on plantation and CPO mills with consideration to various bio-waste treatments."

Jan 1, 2008

By Sahoo K. C

Traditionally, the blast furnace (BF) has maintained a dominant position as the primary source of iron units. Notwithstanding the efficient nature of the process in respect of its material and energy consumption, the conventional blast furnace route is faced with limitations such as stringent quality metallurgical coke, high capital investment, etc. While BF will continue to retain its predominant position as the foremost ironmaking technology, the alternate processes may also have a role to play. Direct Reduced Iron (DRI) or sponge iron industry is all set to take a firm root in India as one important solution to the problems of shortage of metallurgical coal and ferrous scrap and high investment costs faced by the country's steel industry. The commercial proven DR processes coupled with electric arc furnace (EAF) steelmaking have also offered a viable alternative to the blast furnace - basic oxygen furnace (BF - BOF) route for the installation of integrated plants under specific local conditions. The performance and efficiency of DRI processes mainly depend upon the chemical and physical behaviour of the raw materials especially the iron bearing materials. Iron oxide pellet and sized lump ore constitute the oxide feed stock, while pellets form an ideal feed stock for direct reduction, use of lump ore is economically advantageous because of its lower price. National Mineral Development Corporation Limited (NMDC), being one of the major producer of iron ore in the country since last four decades, has established technology and developed process flowsheets for production of suitable calibrated lump ore for DRI production, besides supplying the natural lump ore for conventional blast furnace requirements. In addition to the above, extensive pilot plant tests have been carried out at the R&D Centre of NMDC for preparation of iron ore concentrates suitable both for direct reduction and blast furnace grade pellet feed using the iron ore fines from its own mines and as well as from the other iron ore mines in the country. For utilisation of the huge quantity of slimes generated in its ore processing plants, NMDC has planned to set up the first commercial plant adopting the smelt reduction process (ROMELT Process) for production of pig iron from Bailadila slimes. The paper mainly deals with various beneficiation techniques adopted for production of DRBF grade pellet feed from iron ore fines. Also presented in the paper, the extensive work carried out at R&D Centre on preparation and evaluation of calibrated lump ore (Natural Pellets), based on which, suitable modifications are incorporated in the ore processing plants of NMDC for production and supply of the same to sponge iron industries.

Jan 1, 1999

By Joe Roby

Rolling disc cutters are the business end of hard-rock and mixed-face tunnel boring machines (TBMs). Since their first successful employment on a TBM more than 50 years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates are higher and cutter costs are lower than ever before, proving the value of investment in cutter development. Disc cutters are used on a range of tunneling equipment, from pipe jacked slurry micro-TBMs less than 1 m (3.3 ft) in diameter to 15 m (49 ft) in diameter, hard-rock boring TBMs. The geological conditions under which they are employed range from sands and gravels, with several bar of water pressure, to extremely hard, massive rock with UCS up to 420 MPa. Regardless of the type of machine or geology, one thing remains constant: changing worn out cutters is costly. When cutters must be changed in the middle of a tunnel, the contractor incurs the cost of downtime as well as the cost of refurbishing or replacing the cutters. In the case of catastrophic cutter failures, the project can be stopped completely for long periods, and the costs mount up rapidly while tunnel production is at a stand still. Catastrophic cutter failures include the occasion when hard-rock disc cutters are failed in groups (called a ?wipeout? phenomenon) and the operator fails to stop the machine, which results in severe damage to the cutterhead. The cause of this can be either an undetected failed cutter propagating damage to surrounding cutters or operator error in steering. Regardless of the cause, the resulting damage can take days or even weeks to repair. When cutters fail prematurely on EPB or slurry machines in certain geological conditions, it is impossible to evacuate the chamber and, therefore, impossible to get [ ] into the chamber to change the cutters. The solution is frequently an unplanned intervention shaft that must be sunk at great cost. The importance of being able to predict cutter life accurately, and in all geological conditions, cannot be overemphasized. For these reasons, cutters have been developed for specific machine types and sizes, as well as for specific geological operating conditions. Different size cutters are required for different size machines. For example, while 483- and 508-mm (19- and 20-in.) cutters are used on large diameter TBMs, it is impossible to employ cutters so large on a small micro-TBM. Also, the cutter must be designed for the specific geological conditions under which it will be operating. The disc cutter rings required to bore extremely hard rock are the most expensive of cutter rings. However, they provide little advantage in weaker rock formations where less expensive rings will do the job as well. It is important to choose the correct cutter for the machine and the geological conditions in order to get the best balance of cost and risk.

Jan 1, 2009

By Roberto Chambi

"El presente trabajo señala la expansión de la producción de la mina Condestable a través de las innovaciones tecnológicas en clasificación de molienda como: la utilización de estas zarandas derrick de cinco pisos cada uno, donde se aumenta la capacidad de cada molino instalado en planta en un 17% en promedio, así como el grado concentrado supera el promedio de 26.35%."

Sep 9, 2007

By Guy T. McBride

Mr. Chairman, Fellow Keynoters, Ladies, and Gentlemen: It is purposed to consider the theme of this meeting, "The 1970's - Pivotal Decade for the Mineral Industries," from the particular -- some would say peculiar -- point of view of one engaged in mineral engineering education, and this coign of vantage prompts the textbookish subtitle, "Problems and Solutions (?) in Undergraduate Mineral Engineering Education." Three interrelated problems, or problem areas, will be presented and discussed, and where solutions seem to be emerging or seem worthy to be suggested, they will be identified. The three problems are: 1. The goals, and therefore the course requirements, of the undergraduate curricula are in question, 2. The unit costs of undergraduate education appear excessive to those who bear the charges, and 3. The social ambience of the day affects for the worse the work attitudes and the career motivation of both prospective and in-course students. The Need. - Any discussion of these problems must bottom upon recognized national needs for minerals and a technologically sound minerals industry staffed by competent engineers, particularly at the exploration, development, and production levels, Fortunately, these needs have been recognized and to some extent quantified, and they are even now under further intensive study by some of the most competent members of our society and profession. The latter reference is, of course, to the current work of the National Commission on Materials Policy (U.S.A.) under the executive directorship of Dr. James Boyd. Predating this, and perhaps to some extent

Jan 1, 1972

By Forrest T. Moyer

INJURY experience and employment data are presented in this chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume II. The 1962 figures are preliminary summations which are subject to revision. They were compiled from all reports from producers received by the Bureau of Mines through April 15, 1963. The data for metal, nonmetal (except well and brine operations), stone, and sand and gravel operations were collected by a mandatory reporting system under the provisions of the act of September 26, 1961, Public Law 87-300 (75 Stat. 649). The act authorized the Secretary of the Interior to study the various aspects of safety in metal and nonmetal mines (excluding coal mines) and report the findings 2 years sub-sequent to the enactment of the law. Data on nonmetal well and brine plants and nonferrous reduction plants and refineries were reported voluntarily by the operators. METAL MINES Preliminary data for the metal mining industry comprise reports on 1,871 mines and pits. The combined fatal and nonfatal injury-frequency rate was 31.95 per million manhours in 1962, a decrease of 8 percent from the similar rate of 34.54 in 1961. Metal operations reported a total of 61 fatal and 3,201 nonfatal injuries.

Jan 1, 1963

Recovery of Tantalum Capacitors from Waste Printed Circuit Boards Using a Pneumatic Separator

Sep 13, 2010

This report summarizes the work performed and results achieved on the above contract from October 18, 1971 through July 14, 1972 under Phase II, Task 1: Detailed Design of Prototype and Task 3: Supporting Experimental Investigation. Operation and Service Manuals resulting from Task 3 are submitted under separate cover as are detailed design drawings and specifications, prepared under Task 1. Both items accompany this report. This report also includes (A) an estimate of the cost of construction, (B) a description covering the use of the equipment, and (C) a proposed test plan to demonstrate performance of the equipment in both the laboratory and a mine.

Jan 1, 1972

By M A. Lund, C D. McCullough

In Australia and worldwide, open cut mining has become increasingly common over the last few decades through changes in excavation technology and ore economics. However, such operations frequently leave a legacy of open mine pits once mining ceases. Pit lakes will then form in mine pits that extend below the water table when dewatering operations cease. Pit lake waters are typically contaminated with metals, metalloids, saline or acidic/alkaline and rarely approach natural water body chemistry. Physically, pit lakes have unique bathymetries, are often strongly wind sheltered and have very small catchments. Nevertheless, pit lake waters often constitute a vast resource but of limited beneficial use (due to water quality issues); with a potential to contaminate regional surface and ground water resources. Water in pit lakes has the potential to be useful for a range of purposes in the Australian context of characteristic hot, dry climate and relatively few natural water bodies. Consequently, pit lakes can be seen to represent either a significant liability or a water resource to mining companies and regional communities. However, the lack of knowledge on pit lakes continues to hinder their proper management. This paper summarises the limited information currently available on water quality associated with Australian pit lakes. Information on pit lake occurrence, distribution and water quantity and quality is not nationally collated and requires immediate and ongoing attention from both mining companies and regulating authorities. Lack of a readily available database for pit lake occurrence, distribution and water quality fails to realise the potential for these water resources by both mining companies and Australian communities. Lack of access to pit lake quantity and water quality data may also lead to failure to manage this significant source of mining environmental risk.

Jan 1, 2009

By J. C. Agarwal

Slags produced by modern smelting furnaces contain copper values which are unacceptably high for discard. The electric arc furnace is employed commercially to clean copper from flash furnace slags but the addition of highly oxidized converter slags to an electric furnace has created operational problems. Highly oxidized Noranda Reactor slags have not been processed successfully in a pyrometallurgical process. These slags, which contain large concentrations of copper (5 to 10 per cent), are treated in slag concentrators (controlled cooling, crushing and milling, and flotation) which produce a copper concentrate that must be resmelted. Though commercially operable, it will be shown that the slag concentrator has important process and cost disadvantages as compared to a pyrometallurgical process. In this paper an economic comparison is made between a pyrometallurgical process and the slag concentrator. For the analysis, five hypothetical smelting plants are considered. Each plant treats 1200 tons of copper concentrate per day and produces 109,000 tons of copper annually. The plant configurations used in this study are:

Jan 1, 1976