Search Documents

By André C. Zingano

The coal pillars in room-and-pillar mining method are subjected to vertical stress due to overburden rock mass and horizontal stress relieve due to entries excavation around them. Some coal mining companies are applying rock bolts and steel straps to improve the pillar strength, consequently to reducing the pillar size and increasing coal recovery. This kind of approach deserves some discussion, whether it is pillar reinforcement or just rib support. The efficiency of pillar reinforcement (or rib support) is directly related to the initial load capacity of coal pillar, the type of excavation, and the width to high ratio of the pillar. The objective of this paper is to understand the mechanism of pillar reinforcement (or rib support) using rock bolts and steel straps on pillar ribs. Numerical simulation taking into account the relations listed above. The results showed that the increase of coal pillar strength is very short, and there is no influence on improvement of load capacity of pillar. However, the rib support avoids block falling, rib failure, and displacement, reducing the pillar failure propagation into the pillar center. Keywords: coal, pillar reinforcement, room and pillar.

Jan 1, 2006

By V. Grujic, M. Grujic, D. Salatic

"Two areas are involved in the research work of the comminution process (crushing and grinding). The first one involves the changes of the size class distribution values that are definded by the differential equations in the function of the ore property and working conditions. The second area involves the comminution of the different levels in order to optimize the working parameters and to decrease the operational costs in the grinding process.We have studied, in detail, the possibility of functioning the crusher at the maximal loading, over 4500 kN, ball mills with diameters larger than 5.0 m and semiautogenous mills with diameters larger than 10.0 m.Using the computers, we have achieved the maximal loading range of the crusher, over Fc ? 4500 kN in the crushing process. In the grinding process, using the adequate differential equations in the automation process, we have established the correlation between the pulp mass capacity in the mill, pulp dencity, ore fineness in the pulp and recirculating ore charge.With the appopriate text, equations and graphs, this paper shows the results of our several years research work in the laboratory and in the ore comminution plant of Majdanpek Copper Mine."

Jan 1, 2003

By Edward E. Tate

This is a report on the design, development, and manufacture of a prototype roof bolting machine for high rise applications. The machine is designed to traverse a 32 inch entry and rebolt a roof fall area to a height of 28 feet 10 inches. Covered in the report is a chronology of the project, an explanation of the design problems, and a description of their solutions. The report concludes that the equipment as designed is suitable for the purpose intended and further testing is recommended.

Jan 1, 1981

By H. Kurushima, S. Tsunoda

An investigation of the hydrometallurgy of Cu-Zn concentrates by The Dowa Mining Co. of Japan is described and a detailed flowsheet of the Kosaka hydro-metallurgical plant is given. Sufficient operating experience has shown that the Dorrco FluoSolids system has proven successful for recovery of both zinc and copper by roasting in a fluidized bed. At present, 2400 metric tons of concentrates per month are being treated and recoveries of 93 pct Cu and 65 pct Zn are being effected. A SURVEY of the Japanese chemical industry in 1949 revealed, among other things, that sulphur-bearing blast furnace gas from the Kosaka smelter of The Dowa Mining Co. Ltd., Kosaka, Japan, was being exhausted to the atmosphere as waste. In addition, it was costing that company an average of ten million yen ($28,000) annually for damages to the surrounding property caused by the sulphur dioxide in the gas. It was recommended by this survey that the gas be utilized for the production of sulphuric acid by the contact process. Mr. Kurushima visited the United States in May 1950 to investigate the engineering, construction, and operation of a contact acid plant. Any acid produced at Kosaka would necessarily have to be 98 pct H,SO, to prevent corrosion in railroad tank cars transporting it to the point of use. However, the production of 98 pct acid requires constant volume and SO, content of the gas. As the converter gas at Kosaka fluctuates in both volume and quality, it was decided to evaluate the smelting process with relation to other methods of recovery. This evaluation revealed a relatively new type of roaster, the Dorrco FluoSolids reactor, which was reported to be capable of roasting the copper sulphide concentrate in an excess of air with the production of an SO1 gas strong enough for acid production and a water-soluble copper sulphate calcine. The copper sulphate then could be leached from the roasted ore and electrolytic copper recovered from the leach solution in much the same manner as practiced by the Chile Exploration CO. for treating naturally occuring copper sulphate ores. Use of a reactor of this type would eliminate the need for a blast furnace and converter and, in addition, would effect savings in labor and fuel. The Kosaka ore is a microscopically fine mixture of copper, zinc, and lead sulphides. The lead and a small amount of the barite present can be separated by flotation, but any separation of copper and zinc proved extremely difficult. In blast furnace operation at Kosaka, zinc had been slagged off until a stockpile of about 12,000,000 tons containing 5 pct Zn had been accumulated. Mr. Kurushima felt that if any of the zinc in the concentrate was sulphat-ized and leached with the copper, it also could be recovered electrolytically. The Dorr Co., sponsors of fluidization technique in the metallurgical field, suggested that sulphate roasting be tested out on a laboratory scale and that, if successful, a commercial Dorrco FluoSolids system be constructed. They indicated that the results from such laboratory tests could be transposed to a commercial scale without pilot planting the roasting operation. It was therefore decided to send samples of flotation concentrate to the West-port Mill, laboratories of The Dorr Co., for testing. The objective of Mr. Kurushima's visit to the United States thus had changed from investigation of sulphuric acid plants to a fundamental examination of the hydrometallurgy of copper and zinc. Testing Program In February 1951, Mr. Tsunoda went to the United States to witness the application of the FluoSolids system to sulphate roasting at The Dorr

Jan 1, 1956

By R. F. Nielsen, R. G. Bentsen

Jan 1, 1966

By James A. Wasson

This report summarizes the results and conclusions reached by various investigators who have attempted to determine the extent to which hydraulic fracturing will affect the secondary recovery of crude oil by waterflooding. It also discusses the most advantageous use of this well-stimulation method in waterflood projects. A thorough search of the literature was made, and pertinent information was abstracted from appropriate reports. A carefully designed and controlled program of formation fracturing is an effective aid in waterflooding because it increases water-injection and oil- production rates. Generally, fracturing has resulted in little or no reduction in ultimate oil recovery, but under certain circumstances recovery has been substantially increased.

Jan 1, 1963

By A. Bothma

The Impala No. 1A ventilation shaft is located approximately 15 kms north of Rustenburg and is accessed via the R510road from Rustenburg to Northam/Thabazimbi. This situation is shown on the location plan in Figure 1. The geology at the site consists of an upper layer of black turf of about 1 metre in thickness, grading into weathered norite. The depth of weathering is generally less than 5 metres. Zones of deeper weathering may occur along fracture zones associated with faults and dykes. Groundwater occurs mainly within the weathered/fractured aquifer system. The ventilation shaft is a 5.1 m diameter upcast shaft ,and forms part of a system of ventilation shafts to complement the existing infrastructure as mining progresses down the new twin decline extension of Impala 1 shaft. The principal reason for these shafts is to lessen the risk of an extended RAW and also to counter the effects of the heat build-up as the mining goes deeper, with the resultant effect that the existing cooling centre (fridge plant) becomes more remote from activities. The No. 1A shaft (upcast) is positioned approximately 1,2 km on down dip from the main shaft and the No. 1Bshaft (downcast) approximately 1,2 km further. Geological information was used from a borehole 1,2 km away on strike from the upcast shaft. The first shaft (1A) is a 5,1 m diameter hole to be fitted with two 2,2 MW fans, whilst the second shaft (1B) is 4,1 m diameter to accommodate a 7MW fridge plant.

Jan 1, 2001

By Kanaan Hanna, Mir Heydari, Dipack Sengupta, Gordon B. French

This article concludes a two-part series on the safety, technology, and economic impact of eliminating safety fuse from metal and nonmetal mines. Discussed are the consequences of fuse abolishment, the technical feasibility of changing to an alternative system, and an economic analysis of initiation systems. Last month, part one (ME, pages 31-35) described current use of initiation systems, incidence of accidents, and consumption values for safety fuse and other initiation systems. Consequences of Fuse Abolishment Cap and Fuse Manufacturers Two major safety fuse manufacturers, Ensign Bickford and Apache Powder Co., share the US fuse market. Marketing of Ensign Bickford safety fuse is done by Dupont. Dupont manufactures electric caps as a main product and recently introduced a new nonelectric initiation system (Detaline). Therefore, Dupont would be only slightly affected by the elimination of safety fuse from metal and nonmetal mining. Ensign Bickford, though a larger manufacturer of fuse, does not appear to emphasize the safety fuse market. In fact, safety fuse sales represent only about 10% of Ensign Bickford's total sales volume. Ensign Bickford is strongly pushing its Nonel product. It appears, therefore, that the elimination of safety fuse would have a limited effect on Ensign Bickford, and could ultimately be to the company's advantage. Apache Powder Co., however, would be seriously affected if safety fuse was eliminated. Safety fuse, although not its only product, constitutes a major source of revenue for the company. It currently does not manufacture a substitute product. Apache Powder Co.'s manager agrees that prohibiting the use of safety fuse would result in a greater market share of initiators for Ensign Bickford. Hercules could also benefit from the prohibition of safety fuse. Metal and Nonmetal Mining Industry According to an explosive company contact, elimination of safety fuse by a mandatory regulation would force some of the small, marginal mines out of business. Another powder company representative believes that eliminating safety fuse will result in uneasy situations for small operators not familiar with other techniques. These operators try to minimize the costs and traditionally like safety fuse. He believes that insufficient proof exists to substantiate the overall safety increase if the fuse is eliminated. Fuse manufacturers and distributors disagree, then, about the impact of safety fuse elimination. However, they tend to agree on some important points: • Safety fuse can be a safe method if applied properly. • Electric blasting can be dangerous due to stray currents, and may have higher misfire rates than safety fuse. • It is very difficult to compare the rate of misfires and partial round failures for different systems. This is due simply to the nonavailability of such data. In many cases, the misfires are not even reported to the shift boss, as required by regulations. • Safety fuse has high acceptance in certain applications, such as a face where Nonel or detonating cord are used, or in open-pit blasting. • The safety fuse industry appears to be phasing out on its own. It is expected that the fate of the safety fuse market will be similar to that of black powder. An investigation by Nitro Noble of Sweden "clearly states that the diminishing use of safety fuse has considerably reduced the accidents in Swedish mines." Mine Data Acquisition and Analysis As a part of the study effort, visits were arranged to 24 metal and nonmetal mines. In most cases, underground visits were accomplished. At least one drilling and loading operation was witnessed. The mines were grouped into four mining areas: Wyoming, Montana, Idaho; western Colorado and eastern Utah; Missouri; and southern Arizona. Of all mines visted, the safety fuse system was used in 11 mines, electrical system in seven, Nonel in five, and the Hercudet system in one surface mine. At each mine, the manager, foreman, and blasting crew were interviewed for information and opinions. Besides informal discussions with mine officials, a questionnaire was also filled out for each mine. Due to the extensive length of the information gathered, these data are not presented here.

Jan 2, 1984

Several industrial-scale HydroFloat separators have recently been installed at Mosaic?s South Fort Meade beneficiation plant for the purpose of improving phosphate recovery and throughput capacity. This technology was implemented after numerous laboratory, bench-scale and on-site, pilot-scale test campaigns. The results from this detailed test work provided sufficient justification for the complete retrofit of the existing coarse and ultra-coarse flotation cells. Data indicate that the metallurgical results obtained with the full-scale separators are consistent with that obtained during both the bench- and pilot-scale evaluations. The benefits, theory of operation and commissioning of the equipment are also discussed.

Jan 1, 2007

By D. Imeson, T. Grammatikopoulos, G. Pearse, M. Aghamirian, C. Mohns

"Spodumene mineral is a source of lithium for lithium ion batteries. Thus, the production of a spodumene concentrate with an approximate grade of 6% Li2O is targeted. Traditionally, spodumene is concentrated by froth flotation using fatty acid as the collector. Amine collector can also be used to float mica ahead of spodumene as required or feldspar from the spodumene tailings. Slimes have a negative effect on spodumene flotation and they are commonly separated by scrubbing and de-sliming prior to spodumene flotation. The main losses in spodumene flotation typically occur in cyclone overflow, scrubbing slimes, spodumene flotation tailings and mica concentrate. In recent years, dense media separation (DMS) is the main concentrating process in Australian spodumene operations. In these operations, DMS is efficient at generating coarse grain concentrates and rejecting large portions of silicate gangue, thereby directly reducing the milling cost. The ore should be crushed to 3/8” or coarser while further crushing is possibly necessary on the middling particles to scalp further spodumene. The DMS feed should be classified to remove fines (typically -0.5 mm particles). The final middlings and undersize fractions could then be processed by flotation. The main requirement in DMS operations is to have good spodumene liberation at relatively large grain size. This paper reviews the most significant DMS and flotation parameters in spodumene beneficiation. The treatments of different minerals in the spodumene ore are also addressed.INTRODUCTION A number of laboratory/pilot plant programs have been recently conducted at the SGS Lakefield site, sponsored by different clients. The main objective has been to develop a process flowsheet to generate a spodumene concentrate containing 6.0% or higher Li2O (~75% spodumene) suitable for producing lithium carbonate by a hydrometallurgical process. Depending on spodumene liberation size, dense media separation (DMS) can be an attractive option to produce a final high grade concentrate and to reduce the mass to be treated in the flotation circuit. In such a case, crushing would typically be performed in stages, with DMS separation to recover a spodumene concentrate and reject gangue minerals following each stage. DMS middlings and -0.5 mm fines can be processed by flotation to further recover spodumene. In the flotation process, coarse stage grinding minimizes the grinding cost and formation of slimes. In the majority of cases, a grind size (K80) of approximately 200 microns is sufficient for flotation. After primary grinding, mica, if present in an appreciable amount, should be floated to minimize interference with spodumene flotation. Desliming after scrubbing and high density conditioning are the key process operations prior to spodumene flotation. Spodumene can then be floated from silicate gangue minerals with a fatty acid or a mixture of fatty acid and petroleum sulfonate at slightly alkaline pH. Subsequently, feldspars can then be floated from the spodumene tailings."

Jan 1, 2012

By M. Mikhaylenko

Rhenium, molybdenum and tungsten are the elements demanded by high-end technologies. These metals are found in process solutions in forms of their oxyanions: ReO4-, MoO42- and WO42-. The later two can exist in forms of iso- and/or heteropolyanions. Basically all three metals demonstrate very similar chemical behavior in aqueous solutions. Unfortunately, in their mineral sources these elements commonly accompany each other, like pairs of rhenium-molybdenum or molybdenum-tungsten. Their economical separation is a challenging task.

Jan 1, 2012

By Allen McComas, Frank Chase, Phyllip Worley

Longwall mining has gained the reputation as being the safest extraction method in underground coal mines. However, one of the most difficult tasks associated with longwall mining is moving the face once a panel is completed. Based on Mine Safety and Health Administration (MSHA) fatality reports since 1996, longwall face recovery operations have claimed the lives of 5 U.S. miners and have resulted in numerous injuries. Recovery operations can be hazardous because they involve moving large pieces of equipment in very confined spaces. They are also conducted in highly stressed ground conditions due to front abutment loads generated by panel extraction. Shield removal is the most hazardous operation during face recovery because miners are constantly exposed to the unpredictable gob edge. To protect the miners, one or more walking shields, cribbing and/or other supplemental roof and standing supports are typically employed as breaker line supports as each shield is removed. At the Harris No. 1 Mine in southern WV, mobile roof supports (MRS’s) have been used in lieu of traditional walking shields on 17 face moves since 1997. MRS’s are shield-like support units mounted on crawler tracks and are commonly used during room-and-pillar retreat mining operations. For longwall recovery, the two biggest advantages that MRS’s have over traditional walking shields are that they are remotely controlled and are highly maneuverable. MRS’s have contributed to safer shield recovery and shorter move times at the Harris No. 1 Mine. This paper will address both the safety and the operational issues associated with MRS usage during shield recovery. It will also discuss new developments, including the use of the inherently safer battery powered MRS’s, which have been recently certified by the Mine Safety and Health Administration.

By R A. Lynch

The state-of-the-art in cave seismic monitoring is reviewed, with the latest developments in active seismic monitoring included. Seismic monitoring systems are routinely used by most of the world’s block and panel caving mines to track the cave initiation and progression. The current best practice is to use the cloud of seismic event locations as a proxy for cave growth somewhere below. Problems with event location reliability due to seismic ray bending around the (unknown) cave are side-stepped by using sensors installed above the cave. However, the aseismic gap – the (unknown) distance between actual cave back and seismic event cloud – currently hinders reliable estimation of cave geometry.Velocity inversions using the passive seismic data are inexpensive and should be undertaken more routinely. The straight-ray methods should be used with caution, as the underlying assumptions are invalid in caving environments. The double-difference method is more correct for the caving situation, and there have been some promising results published. Constrained geometric inversions make a lot of sense, but have yet to be demonstrated successfully.Two active seismic source have recently been developed for use in the caving environment: a piezoelectric source for ranges up to a few hundred metres and a pneumatically-powered source for ranges up to a kilometre. These sources produce signals on standard mine seismic sensors that can be used to measure seismic velocity variations down to 0.01 per cent resolution. This allows the cave progression to be monitored by measuring tiny changes to seismic velocities as the rock above the cave is fractured and destressed.CITATION:Lynch, R A, 2016. Active and passive seismic monitoring of cave front evolution, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Implementation of Fine-Screening in Preparation of KGHM PM SA Sandstone-Carbonate Copper Ore for Flotation

Sep 13, 2010

By K. Norris

"The Campbell mill has undergone numerous changes over the past 43 years. However the rate of change has increased significantly in the last 4 years. A new grinding circuit, carbon-in- pulp circuit, pressure oxidation plant, and column flotation circuit are all new additions. Other changes have occurred in the last 2 years including a large reduction in sodium cyanide consumption, and the introduction of a computer controlled grinding circuit. More improvements are planned in the next 2 years. Some of these improvements include the construction of an effluent treatment plant, and the replacement of filtering and Merrill-Crowe precipitation with carbon-in-leach and electrowinning.Recent changes and improvements to the Campbell mill are a commitment by Campbell mill personnel and Placer Dome Inc. to decrease operating costs, increase gold recovery and gold production, improve industrial hygiene and safety, and meet environmental compliance with current government legislation.INTRODUCTIONThe Campbell Mine has been and continues to be one of Canada's premier gold mines. Campbell Mine is 100% owned and operated by Placer Dome Incorporated. Milling of ore commenced in 1949 at a rate of 300 tons/day producing 58,000 ounces per year of gold. In 1992 Campbell Mine will mill 1340 tons/day of ore at a grade of 0.6 ounces/ton, producing 275,000 ounces of gold at a cash cost of $205.00 Cdn./ounce.This paper discusses some of the changes that have been made to the Campbell mill in the past 4 years. The flowsheet has undergone extensive changes and will continue to change rapidly in the next 2 to 3 years. A simplified flowsheet of the Campbell mill is shown in figure 1."

Jan 1, 1992

By J. Chae, D. Pecha, R. Andrews

The Henderson/ML King CSO Project is a major combined sewer overflow (CSO)reduction project for the Department of Natural Resources and Parks of King County, Washington. The central element of the project is the 3100 lineal feet long, 14'-8"diameter 42nd Ave S Storage/Treatment Tunnel. During the course of the project, the owner and consultants evaluated numerous elements of the tunnel including the alignment, geotechnical conditions, tunnel liner, and settlement monitoring requirements. The contractor utilized innovative shaft construction methods for the tunnel portals, and adhered to strict contract requirements in successfully constructing the tunnel. This paper provides an overview of the design and construction elements of the 42nd Ave S Storage/Treatment Tunnel that led to the successful completion of the project.

Jan 1, 2005

By David Hake, David Salisbury

The Drainage Services Department (DSD) of the Hong Kong SAR Government commissioned the design and construction of the West Kowloon Drainage Improvement, Stage 2, Phase 2, Kai Tak Transfer Scheme (KTTS) project in 2000 to relieve potential flooding in Mong Kok caused by the insufficient capacity of the existing storm water drainage system. The KTTS involves construction of a 1.5km,4.4m drainage tunnel and a 450m long box culvert, running from Waterloo Road near Hereford Road to the existing Kai Tak Nullah in San Po Kong. This paper describes the design and construction of; the bored tunnel through both hard rock and soft ground using a slurry Tunnel Boring Machine (TBM), six associated access shafts, a connection structure at Waterloo Road and the box culvert connecting the bored tunnel to the outfall at Kai Tak nullah. Details will be provided on the contractor’s alternative designs adopted during the contract including the use of fibre reinforced shotcrete as one-pass temporary and permanent support for three of the shafts and modifications to the Engineer’s design for the box culvert structure.

Jan 1, 2005

By L. Hekkala, J. Ollila, J. Keihäs, P. Mäkelä

The Outokumpu Steel Belt Sintering (SBS) Technology is used for manufacturing chromite pellets that are charged into a smelting furnace for ferrochromium production. One of the main elements in successful furnace operation is the control of gas flows inside the furnace, giving improved temperature distribution in the bed during the process. Computational Fluid Dynamics (CFD) gives excellent opportunities for studying these phenomena. An investigation using CFD can be performed relatively fast. For example, implications of different configurations can be studied within a day and an optimum design chosen. Therefore, Outokumpu Technology has developed a Steel Belt Sintering Model (SBSM), which takes advantage of a commercial CFD code. Each main physicochemical event occurring in a steel belt sintering furnace is incorporated independently in the SBS model as a sub-model, enabling every event to be studied separately. The commercial CFD code solves mass, momentum, species and energy equations for determination of the gas flow, composition and temperature. In addition, the Outokumpu SBSM takes into account the moving pellet bed, drying of pellets interms of water content, coke combustion, oxidation and reduction of chromite and the decomposition of carbonates and silicates. During the development of the model, numerous laboratory-scale tests were performed. The sub-models were validated against the laboratory tests. The reliability of the Outokumpu Steel Belt Sintering Model was validated against a pilot-scale batch-sintering furnace by comparing the modelling results against measurements. The aim of this paper is to give a brief presentation of the Outokumpu steel belt sintering model by showing some general modelling examples. Emphasis has been placed on demonstrating some of the main features of the model.

Jan 1, 2007

By T van Niel, M Trefry, B Baker, I Rea, A Hawdon, D McJannet, D Boadle, R Fandrich, A Littleboy

Many open cut mines extend to depths well below the natural water table level with constant dewatering required to maintain operations. When mining activities cease the groundwater starts to fill the void and pit lakes form. The resultant pit lake is directly connected to the surrounding water table and understanding the hydrological and chemical evolution of these lakes is important for minimising environmental impacts. In Western Australia alone there are currently 1800 mine voids and more than 150 mines operating below the water table (Johnson and Wright, 2003). In conjunction with BHP Billiton Iron Ore, CSIRO has been undertaking research to measure and model rates of evaporation from pit lakes in the Pilbara region of Western Australia. Extreme high temperatures and low humidity ensures that this region experiences the highest evaporation rates in Australia.CITATION:McJannet, D, Hawdon, A, Boadle, D, Baker, B, van Neil, T, Littleboy, A, Trefry, M, Rea, I and Fandrich, R, 2016. Measurements and modelling of evaporation from abandoned mine pit lakes, in Proceedings Life-of-Mine 2016 Conference, pp 106–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Morabito J, Harrop D. W

Uranium exploration was commenced in 1973 and carried out at a regional scale over a wide area of the northern part of the Camarvon Basin of Western Australia by Minatome Australia Pty Limited and their joint-venture partners. As a result, pervasive uranium mineralization has been found in the Cretaceous sandstones near Manyingee Hills in the Onslow Region, which were probably deposited in a near-shore, fluvia deltaic palaeo-environment.Mineralization is generally found in poorly sorted argillaceous sandstones and siltstones near redox fronts formed by oxidizing waters circulating in reduced sediments. The principal minerals found in the two Manyingee deposits delineated so far are coffinite, uraninite with associated pyrite in the reduced zones, and phosphuranylite, siderite and limonite in the oxidized zones. The presence of dissolved uranium in the superficial aquifers, of secondary uranium minerals as coatings on granitic rocks, and of recent uranium-bearing calcrete sediments, suggest that the whole Cretaceous-Precambrian system has been subjected to the formation ofroll-front type uranium deposits since the Cretaceous. Continuing exploration is locating additional uranium occurrences. The deposits outlined so far are being evaluated for their amenability to in situ leaching tests planned for 1982-1983.

Jan 1, 1981