Search Documents

By R. C. Bunge

Many minerals float best with fatty acids in the intermediate pH range. For example, fluorite, a semi soluble salt mineral, exhibits a maximum contact angle and a maximum flotation recovery in the pH range of 6-8 after conditioning in a palmitate solution (fig. 1). The maximum in flotation coincides roughly, as many researchers have observed, with the boundary of bulk precipitation of the fatty acid. According to fig. Z this boundary is in the above case of 5xl0-7 M palmitate approximately at pH 6.3. For assessing the phenomena occurring at the bulk precipitation boundary of fatty acids, the surface tensions of carboxylate solutions have been measured under various conditions. Fig. 3 shows the surface tension development of palmitate and myristate solutions of increasing concentration at pH 12. Also shown are the bulk precipitation edges (BPE) of the respective solid species that is stable under these conditions, that is the potassium acid soap, HKAZ. Both curves display a similar behavior. As the concentration of carboxylat,e increases, the surface tension decreases, until a minimum is reached at which the curves level off. The decrease of surface tension with increasing carboxylate concentration is generally taken to indicate the surface excess of the carboxylate ion. The point where the curve suddenly levels off has not yet been explained. While it is well known that the onset of micellization (CMC) may cause such an inflexion of the surface tension curve, this cannot be the case here because the position of this point depends, as shown in fig. 4 for palmitate, on pH (the CMC is generally independent of pH). We believe that this point indicates the precipitation of a colloidal acid soap (colloidal precipitation edge, CPE) before the bulk precipitation of this species sets in (BPE).

Jan 1, 1994

By S. S. Dean, B. Silkes

"INTRODUCTION The metallurgical-research program of the Bureau of Mines .for the past 15 years has emphasized the production of high-purity nonferreus metals through the utilization of our available resources, ores, reducing agents, fuel, and power.Ore dressing or concentration, has always been a vitally important part of nonferrous metallurgy, and the Bureau continues to give most of its attention to it. In the field of the traditional nonferrous metals, the Bureau staff has developed natural-gas reduction of zinc, the application of glomerule technique to preparing high-grade lead concentrates for Scotch-hearth smelting, the production of electrolytic antimony from precious metal-bearing ores, and the recovery of nickel from nickel-chrome-iron ores.In the field of light metals, the Bureau staff has developed several improvements in both magnesium and aluminum production and in alloys of these metals. In the so-called ""rare-metal"" field, Bureau activities have included the production of pure ductile titanium on a larger scale than heretofore attempted, the electrolytic production of cobalt, chromium, and manganese which may now take their proper places as bases for nonferrous alloys as well -as ingredients of special steels. The Bureau staff has investigated many of these new alloys. Investigations of methods of recovering vanadium from its low-grade domestic ores have given promising results. Methods for the preparation of metallic zirconium have been improved."

May 1, 1947

By Walter S. Bergholz, Michael L. Schreder

"Since Escondida began operations in fiscal 1991, a series of aggressive expansion projects have enabled market share to be increased and ever larger profits to be realized. This was possible due to the very large size of the ore body and its high grade - averaging 2.7% copper from startup through fiscal 1997. The situation has now changed: ore grade is falling rapidly and is projected to be only 1.55% by 2003. Since revenue is directly proportional to ore grade, while costs are proportional to quantity of ore processed, profits will begin to fall dramatically. The Phase IV Expansion Project is intended to forestall this drop in profits by increasing ore processing capacity by over 85%.The Phase IV concentrator is designed for a nominal capacity of 110,000 MTPD and the key to achieving this value is through the proper design of the grinding circuit. This paper presents the general design criteria for the grinding circuit, as well as a description of the facility.INTRODUCTIONThe Phase IV Expansion Project consists of a new copper concentrator located 8.5 km south of the existing operations, a new tailings disposal and water reclaim system, a new concentrate slurry pipeline to the coast, and added concentrate handling capacity at the port of Coloso. The new concentrator has a nominal capacity of 110,000 tonnes per day (MTPD), compared to the existing concentrator’s capacity of 127,500 MTPD. The Laguna Seca concentrator is based on using the largest and most efficient ore grinding mills now available.The concentrator has been designed for a 110,000 MTPD nominal capacity. The process design criteria for the Phase IV project were established from in-house operating information and from test work. Unlike a green field project, Escondida already had an operating plant and it processes ore from the same pit that feeds the Phase IV plant. It is expected that the current mineralization will be similar for the first 6 years of operation of the new project. Therefore, some of the current plant operating conditions were incorporated directly into the design criteria."

Jan 1, 2004

By Patricia Petty

If enthusiasm is a requirement, the coordinator of the Total Concept program is a dynamic, exciting leader with a lot of potential to keep the program a vital and progressive effort for many years. Art Meyer is entering his third year as the leader of the Total Concept. He is using his years of experience in the industry to emphasize the basics required for the course, and has also instituted new programs. Meyer began his career, after graduation from CSM as geological engineer in 1950, with St. Joe Lead. He held other responsible positions with Amax and Rocky Mountain Energy. He can answer any questions that may crop up or find the right resource person for those questions. Additions to the 18-year-old curriculum instituted since Meyer became coordinator are the study of industrial minerals and strategic minerals. The industrial minerals portion of the course includes visits to a major sand and gravel operation, in addition to lectures on the subject. Much of the strategic minerals requires study and lectures, since Colorado is not a big production state in these commodities. How does the director arrive at new additions or deletions to the program? "It's very simple," he says. "We listen to questions posed by the students, recommendations by industry people who know what is important, and feed-back from course alumni." Alumni feedback from this course has been extremely gratifying, according to Meyer. Other ideas are constantly surfacing, ideas that will be implemented as time and resources permit. One of the most gratifying results of the Total Concept program from an alumnus was the development of a complete teacher and student package by John Christiansen, a teacher at Cherry Creek High School near Denver. The course so excited Christiansen that he envi¬sioned an energy and minerals course to fill a perceived gap in science education on the high school level. The draft package was so attractive that it was sponsored and the publication costs guaranteed by the Society of Mining Engineers. Today, under the leadership of the Mineral Information Institute, the package is in use in several states and has gained enthusiastic acceptance. Other alumni have launched their efforts to broaden the scope of the existing science education by instituting courses or special seminars. One recent alumnus, Dick Will, class of 1984, who was sponsored by the Denver Mining Club, is conducting a science seminar based on his experiences with the Total Concept program. Meyer will be speaking at this seminar, as well as other industry speakers from the SME GEM Committee Speaker's Bureau. Jane Dianich, another alumna, brought her students at Kent Country Day school, also near Denver, into the mainstream of resource education by taking them on abbreviated field trips similar to those she experienced while in the program. She also has been a vocal supporter of the organization and available to speak to other teachers on the value of the experience. George Wright, of the Lake School and a second sponsoree of the Denver Mining Club, admits he came into the program because the six credit hours given toward his continuing education requirement were attractive. He then stayed on to become an ardent advocate of the mining industry. In his own words, "I'm a convert." Wright has developed a slide presentation and has lectured to teachers and students as well as presenting his views to the Denver Mining Club. He has also indicated a willingness to participate with other organizations who need speakers. The value of these speakers and teachers is obvious, according to Meyer. "They represent a respected segment of the public and are not too `tainted' by association with an industry that is too often under criticism from various groups. They represent, in effect, a citizen's advocacy of the industry, which is an invaluable asset to us all." One of Meyer's concerns about the program is that the out-of-state student rate attendance is declining. He is hoping that more AIME sections around the country will become involved in the scholarship program of the Total Concept. Total cost is about $1200 per student. "The rewards to their sections could be tremendous, with the same kind of participation we get here with speakers, citizen advocates, and interested persons," he said. Teachers say that the course improves their teaching and knowledge in a number of subjects including biology, history, economics, career planning, environmental data, science, math, geography, physics, and chemistry. The recent interest in hazardous waste management has sharpened the desire to learn more about this. And Meyer foresees another segment of the course to emphasize this subject. "One of the most valuable resources we have is the field trip program. The course would probably be meaningless without this opportunity to get out into the field where these folks can see what actually happens. George Wright, for example, was amazed at the very small amount of area actually involved in the mining operation - something contrary to what he had heard in the past." The 45 students are taken by van on eight trips, one each week, and the long trip to Colorado's Western Slope. During this long adventure, the students visit underground mines, including CSM's Edgar, open-cut and underground coal mines, precious metals mines, and oil shale properties. They also have opportunities to meet with mine personnel at each of these stops. These field trips fill another function. Living together and exchanging ideas helps the teachers come up with new concepts for the classroom work - expanding their horizons. "As long as we have a mining industry, this effort will continue to grow," Meyer said, "and will fulfill a need within the public education and public relations area of the industry. We need the support. I have dozens of comments from teachers who attest to the value of this program. They understand. The mining industry must continue to do its part."

Jan 3, 1986

By D. M. Walters

To achieve safe and healthy working conditions in shaft sinking operations, ventilation, and where necessary cooling, must be provided. These requirements are considered for sinking vertical, sub-vertical and decline shafts. Regulatory requirements, determining air volumes and amount of cooling required, the various ventilation methods used such as force, exhaust, twin columns, air reversal using four gate systems and the equipment required to achieve this, are discussed. Consideration is also given to the sinking of single and twin declines using diesel equipment, calculating the air volumes required to dilute pollutants and the various methods for achieving this. Also discussed is the importance of having early ventilation design input to the overall design of the mine. In many cases ventilation can be the prime determinant for the size and configuration of the shafts or declines that have to be sunk.

Jan 1, 2009

By Tim O’Neil

The US Bureau of Mines and the Santa Cruz Joint Venture (SCJV) are working on a production-scale, in situ copper recovery project in Arizona. The research is being conducted at the Santa Cruz site, located 11.2 km (7 miles) west of Casa Grande, AZ (Fig. 1). Santa Cruz is a 1.36-Gt (1.5 billion st) porphyry deposit averaging 0.6% Cu, of which 65% is oxidized, concealed beneath post-mineral alluvium at depths of 365-914 m (1500-3000 ft). The Bureau and the SCJV will evaluate in situ mining as a method for extracting copper from this previously unmined deposit. Research objectives of the Santa Cruz project are: - to demonstrate that an in situ research test can be operated in an environmentally acceptable manner ; and * to operate an in situ well pattern long enough to develop information on copper recovery and economic feasibility data. In situ mining of copper from undisturbed deposits has not been attempted commercially. There are several potential advantages with in situ mining: less exposure of miners to hazards, lower pital costs for the mine and plant and lower operating costs. In addition, there are no pits, dumps or tailings, which means less environmental impact.

Jan 1, 1991

By P. Mogodi

The purpose of the project was to propose a coal clearance system (coal transportation system from the mining face to the plant) that could be used for the planned underground operations at Zondagsfontein Colliery. Components of the current coal clearance system were overlooked during feasibility studies. Subsequent studies of the coal clearance system revealed that the combined capacity of the two trunk belts does not match that of the shaft (main) belt. As a result production downtimes will be encountered due to bottlenecks in the system. Ways of addressing this challenge were analysed by weighing both advantages and disadvantages and ultimately a surge bin option was selected. Belt conveyor simulations were conducted in order to determine the optimum capacity of the surge bin. The configuration of the surge bin in relation to the two trunk belts was chosen by considering development cost, advantages, and disadvantages of each option. It was concluded and recommended that a 500 tonnes capacity surge bin is required to remove the bottleneck from the system.

Jan 1, 2010

"This generic study has been developed in response to the frequently asked question, ""That is the best treatment route for refractory gold ore?"". The study has developed operating and capital costs for many potential treatment routes and they are presented here in a generic form. All costs are in relation to the value of 1.00 given to the base case, a 1000 mtpd bio-oxidation plant, operating at 25% solids and 72 hours residence time.There is unfortunately no simple answer to the above quest ions. The treatment of refractory ores is a complex subject, with many variables, such as mineralogy, chemistry, environment and tonnage. However this study does offer information and relative numbers that we believe will be of assistance to gold metallurgists in obtaining a ""first shot"" at estimating costs.Equally, this technology is a rapidly evolving one. As more plants are commissioned, and test programs completed, better data is constantly being generated. For a generic study of this type to remain useful it will need regular updating and adjustment."

Jan 1, 1989

PUGET SOUND LOCAL SECTION. Executive Committee. CHESTER F. LEE, Chair roan. C. R. CLAGHORN, Vice-Chairman. JOSEPH DANIELS, Secretary-Treasurer, University of Washington, Seattle, Wash. W. C. BUTLER. AL K. RODGERS. On the evening of Tuesday, Sept. 2, an informal dinner was held at the University Club, Seattle, Wash., at which the Secretary of the Institute was present, and a valuable and interesting conference took place concerning the recent activities of the Institute and the relations of the Institute management to the Local Sections. SOUTHERN CALIFORNIA LOCAL SECTION. Executive Committee. THEODORE B. COMSTOCK, Chairman SEELEY W. MUDD Vice-Chairman. FREDERICK J. H. MERRILL, Secretary-Treasurer, 300 Germain Building, Los Angeles, Cal. C. COLCOCK JONES. FRANK ROBBINS. Maintains headquarters at 300 Germain Building, Los Angeles, Members of the Institute are invited to visit these headquarters whenever they are in the city. A reception was held at the headquarters of the Section on Wednesday, Sept. 10, at 8 p.m., to meet the Secretary of the Institute and discuss Institute activities and affairs. Light refreshments were served, and about 20 members of the Section attended.

Jan 10, 1913

The transgressive sedimentary sequence of the Noumea Basin contains rhyolitic lavas and less voluminous mafic and intermediate volcanics of shoshonitic affinities which erupted simultaneously during the late Cretaceous. The shoshonitic volcanism shows a trend froIn early mafic to younger evolved intermediate lithologies. The rhyolites are consistently calcalkaline. There is no evidence of mixing of the two magma types. The shoshonitic volcanism is the result of a short-lived subduction event related to spreading in the New Caledonia Basin and involved reactivation of an earlier esozoic subduction zone.

Jan 1, 1995

In the dimension stone industry, workers in processing shops may be exposed to harmful levels of respirable silica dust when conducting the different tasks in stone preparation, which include cutting, grinding, polishing, and thermaling. To protect workers from this health hazard, operators sometimes ventilate processing shops using fan-powered dust collectors to capture and filter dust. To investigate this issue, NIOSH, Pittsburgh Research Laboratory, in cooperation with a dimension stone operation, upgraded an off-the-shelf dust collector the operator was utilizing in a polishing/cutting shop. Initial dust surveys showed that the unit was under-designed for the amount of dust being generated in the shop. The objective of the research was to cost-effectively increase the air cleaning volume and improve dust capture efficiency of the unit with a larger motor and blower. The unit?s original stock 0.56 kw motor and blower was replaced with a 2.24 kw motor and matching blower to increase airflow. The unit was evaluated both in the laboratory and the shop before and after the retrofit to determine the improvement of the upgrade. The study showed that the 2.24 kw upgrade improved the performance over the original 0.56 kw motor resulting in more dust being cleaned from the ambient air in the shop. The 2.24 kw unit cleaned 19% more air and captured 32% more respirable dust than the 0.56 kw unit.

Jan 1, 2009

By AIME AIME

THE coal classification session* on Monday morning, Feb. 17, was opened by a paper by M. R. Campbell, entitled "Natural Groups of Coal and Allied Fuels," in which he pointed out, by means of graphical presentation of selected proximate analyses of coal, that coals can be classified on the basis of their moisture content. He proposes four groups of coal, brown coal, hydrobituminous, bituminous, and anthracite, each subdivided into two or three sub-groups. In a written discussion of this G. H. Cady, of the Illinois Geological Survey, showed that there is, in general, a progressive decrease in the moisture of Illinois coals from north to south, and that it would be very difficult to draw any arbitrary line dividing the coals of the State into two groups on the basis of moisture content.

Jan 1, 1930

By M Stewart

The structural framework for the major gold deposits of the Reefton Goldfield was largely established in the 1930s after a detailed regional geological mapping programme. Recent new mapping has now substantially modified the structural framework of the Globe Hill - Devils Creek area and the Waiuta area. Using bedding-cleavage vergence as a method of establishing fold limb facing, many new fold structures have been identified, some of which conflict with long-established structures such as the Globe Hill and Waiuta anticlines. In addition, the mapping of areas of west- versus east-facing limbs constrains the position of many faults. The mineralised Globe-Progress Shear is one such fault which graphically demonstrates major structural discordance of the folds in the hangingwall compared to the footwall. Recognition of the folding is establishing the structural framework for understanding of the origin of these productive gold mining areas.

Jan 1, 1996

Two years ago I was sitting in a big lecture theatre at the School of Mines in Kalgoorlie at the annual New LeadersÆ Conference listening to a guy tell us all how much he loved his job, travelling the country ælegallyÆ blowing stuff up à and getting paid to do it. I would have paid to see and do the things he spoke of à now IÆm that guy. From finishing a mining engineering degree at the University of Ballarat, through the job hunt, to firing environmental blasts in Tassie and designing and implementing construction blasts in the middle of the Gold Coast. My name is Rohan Stevens and IÆm a blast-o-holic. While the æjob huntÆ we all embark on toward the end of our degrees is a stressful time, itÆs also very exciting in the current climate. There are a number of things I have learnt through both my hunt for the job that best suited me and working for the worldÆs largest explosives manufacturer. If at least you donÆt benefit from my learnings IÆm certain you will enjoy hearing about (and viewing) some of the work I have had the opportunity to be involved with over the last 18 months with Orica Mining Services.

Jan 1, 2008

By T van der Meer, A Salokannel, M Martikainen, L M. Nevatalo, J McCulloch

Water use and wastewater management is becoming a focus for many industries around Australia and the rest of the world. Good quality water is increasingly being recognised as a precious resource, and regulations on the bulk storage and discharge of waste streams is becoming more stringent in order to protect the environment, existing water reserves and the communities that use these resources. Components such as heavy metals, arsenic, cyanide, and sulfate from acid mine drainage are some that occur at mining and metallurgical processing sites. Removal of such components can allow safe re-use of these streams, reducing the new water requirements of the process, or else allowing acceptable discharge to the environment. Re-use or discharge of treated water eliminates or reduces the risk associated with storage of large volumes of contaminated water on site.Technologies where a contaminant is selectively precipitated and removed as a sludge are used for many of these treatments. Selection of the best treatment option for wastewater must depend on what is suitable to each site, and consider not only the nature of the contaminant, but also other aspects, including the location and situation of the site, local regulations, cost of reagents, the sensitivity of the local environment and waste sludge disposal options. To outline how an effective and economical solution can be designed and delivered, this paper will present a case study for the removal of arsenic from a site wastewater, from assessment of the problem, selection of suitable technology, design and implementation, to the benefits delivered to the site.CITATION:Salokannel, A, Nevatalo, L M, Martikainen, M, van der Meer, T and McCulloch, J, 2013. Technology selection for removal of contaminants from an industrial wastewater, in Proceedings MetPlant 2013 , pp 531-538 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By T. A. Lang

Concepts and equations have been developed to quantitatively determine the stability of a rock bolted coal mine roof as a structural (beam-arch) member consisting of reinforced rock units. The equations take into account: rock bolt tension, length, spacing, and orientation; size of opening, strength and physical properties of the rock; and loads from distressed rock, and were critically reviewed using sensitivity analyses and the results available from relevant previous analytical and physical model investigations. It is concluded that they can essentially be validated by using small scale physical models and the full size mine entry model at the USBM Spokane Research Center. However, a comprehensive research program, including analytical and laboratory investigations and field trials in typical mines, will be required to define and validate criteria and standards for using the equations as a basis for a rational design code for rock reinforcement installations to replace the semi-empirical rules now being used. For example, these studies have shown that the practice of installing vertical roof bolts with a uniform spacing equal to the bolt length is inherently unsafe and that the spacing should be reduced near the walls to prevent shear failure of the roof strata. The development of such a rational design code would provide enhanced safety in coal mining operations and warrants a high priority in the Bureau's ground control research program.

Jan 1, 1981

The disasters between 1920 and 1979 in coal mines in Queensland and New South Wales due to underground fire, gas or coal dust explosion or to gas or coal outbursts, have been assessed. The evidence relating to disasters caused by gas explosion points strongly to divergence from safe mining practice as the main cause. There is a need for greater training and education of personnel, closer analysis of gas reports, better monitoring and testing procedures, improved ventilation standards and a policy where safe working practice is actively encouraged. Conditions in the New South Wales occurrences of gas explosion were similar to those at Collinsville, Queensland in that dykes, igneous sills, burnt out coal and faulting were common to all. Information on outbursts indicates that contributing factors were intrusions, depth of cover, fault zones and other geological disturbances, methods of work, pressure and type of gas.

Jan 1, 1982

By Baha Abulnaga

Slurry pipelines are used in a number of countries to convey processed ore mixed with water over long distances from remote mine sites to ports or plants for further processing. In Egypt and Sudan, numerous mineral resources are scattered in remote areas. Through the years, Egyptian geologists have identified 268 sites for metallic ores and 386 sites for industrial nonmetallic minerals. A large portion of these sites are in the Eastern Desert in an area called the Nubian Shield. Similar sites are found in the Sudan where mining contributes to less than 1 percent of the gross domestic product (GDP). There are three important components of infrastructure needed to develop these resources ? power, water and transportation. While Egypt is able to satisfy 70 percent of its needs in iron ore from the Gadideh Mine in the Western Desert, it needs to expand its other resources to reduce imports heavily sedimented. Dredging of these sediments and transporting them by slurry pipelines would enhance an industry of bricks or agricultural development based on tailings technology often used in mining. This article explores the potential for slurry technology for opening new mines in the desert or recuperating the sediments of the Nile. The technology by itself would be new to both countries and would benefit from collaboration, particularly to de-silt the Nasser-Nubia Lake.

Jan 3, 2010

Review on Some Research Methods of Mineral Crystal Chemistry and Computer Simulation on Flotation

Sep 13, 2010

By Pierre Beaudoin

"This paper deals with the repairs made on two damaged mills. It investigates briefly the causes of the damage, explain its nature and the design of the repair. It explains the detrimental effect on operation and the solutions implemented to reduce them. Finally, to review the follow-up required for such repairs. LOCATIONThe Holt McDermott Mine is located 75 kilometers Northeast of Kirkland Lake and 30 kilometres west of the Quebec border in Northeastern Ontario. The town of Kirkland Lake is located approximately 500 kilometres north of Toronto. HISTORYThe discovery of gold in Holloway Township dates back to early 1920. In 1984 Barrick Resources, which amalgamated with Camflo Mines, acquired more claims on the property and initiated an extensive drilling program. By 1985, the drills indicated reserve increased to 2,500,000 tonnes grading 6.8 g/mt. In 1986 a production decision was made and in 1988 the mine was officially opened.As of December 31, 1998, 4,691,507 tonnes grading 5,66 g/tonnes have been milled from 4 ore-bodies. The mill started up in June 1988."

Jan 1, 2001