Search Documents

By V. A. Danielson

The Bureau of Mines examined sources, consumption, and movement of iron and steel scrap in the southeastern States--Alabama, Florida, Georgia, Kentucky, North Carolina, South Carolina, and Tennessee. Officials of the scrap-processing and scrap-consuming industries were interviewed, data was obtained from the published literature, and a canvass was made by the Bureau of scrap consumers. The Southeast generated excess scrap which was shipped to domestic and foreign consumers in about equal proportion. Total 1963 demand in the Southeast was 3,336,000 net tons, of which purchased scrap was 75 percent, foreign exports 13 percent, and domestic exports 12 percent. Alabama, with 47 percent of the purchased scrap consumption in 1963, was the most important scrap-consuming State, and Kentucky, with 34 percent, was the second most important one. Southeast demand was 4.8 per-cent of the total U.S. demand. Projected 1980 consumption is 8,340,000 tons. Scrap prices showed a slight downward trend for the period 1953-63, although gross consumption increased slightly. A significant trend in processing scrap in the Southeast is the preparation of smaller bundles or "briquettes" weighing from 75 to 150 pounds, which are easier for consumers to handle and inspect. Another significant development is the "shredding" of automobile scrap which produces a dense, clean scrap especially desirable for use in electric furnaces.

Jan 1, 1967

Coagulation-Neutralisation Technology to Treat Wastewater from Lead-Zinc Concentrator

Sep 13, 2010

By Steven P. Oman

Large room and pillar mines are characterized by numerous and widespread working places. Ventilation requirements are high since each panel employs men and equipment that work simultaneously in multiple headings. Also, it usually is not feasible to redirect airflow from idle to active panels as the demands of each shift vary so every panel in the mine is fully ventilated at all times. Ventilation requirements will be even higher for mines that are classified as gassy. As a result of these considerations, ventilation systems for room and pillar mines are generally designed to handle large quantities of air. But as mining progresses and the mine be- comes larger, greater demands will be placed on the ventilation system. To insure that adequate ventilation is maintained at these times, ventilation engineers must anticipate problems and plan how best to deal with them.

Jan 1, 1983

By Rongdong Deng

A tower-like magnetic system comprising eight permanent magnets was installed at the center of a flotation column to separate chalcopyrite and pyrrhotite minerals. A cyclonic flotation was installed within the underpart of the column to separate the pyrrhotite from the gangues. A three-product magnetic flotation column was fabricated to create a magnetic field and a cyclonic zone. The products were Cu concentrates, pyrrhotite concentrates and tailings. The theoretical magnetic field strengths and the magnetic forces were calculated. The results of the flotation experiments showed that the Cu grade increased from 14.20% without the magnetic field to 26.40% in the presence of the magnetic field and that the S grade in the pyrrhotite concentrates increased in the presence of cyclonic flotation. The separation efficiency of this magnetic flotation column was evident. Therefore, this three-product magnetic flotation column may have a potential application, due to its high separation efficiency.

By J. C. Thornley

Service failures of seemingly conventional galvanized bolts, in normal operation, on transmission towers in New Brunswick have been found to be the result of hydrogen cracking. In both these cases, similar failures elsewhere can be avoided by suitable clauses in the purchase specifications. In the first case described, the manufacturing procedure was responsible for strengthening and embrittling a standard, soft, constructional steel. In this case, a fracture mechanics analysis predicted critical crack depths for final fracture very similar to those found in practice. This case reveals an apparent cooperative connection between hydrogen embrittlement and strain ageing in plain carbon steels. In the second case described, the steel was simply a high strength steel which should not have been made into galvanized bolts.

Jan 1, 1979

By Albert L. Toenges

[The i~ ortance o~ S3~e, fdequnt, nQ economical tr~n~po~t~t on 8ys~em Th~a bee~ e~~~~siz8d by the introduction of mechanical loading in co 1 mines, pa.rticula:c y \'r~ e::-e ~o?oile loaciine; ~ac~ine!;j rrre u .... ed. This papar i tr_e . eco:1d or' ?. ~eries deGcribi 1{) t:;'~~11>ort:ltion G stems et1-p oyed in mech3JlizeG. f!lincs. Progre,-s ?. epo~ t J...2.t deal t ~~tirel.: ,'Ii th the l:se of rail .laulagr £or c;atl:erine tran~ortc;tion, ailc, in t-!is paper 'Ii 11 be i acuss d c .icilY rub"col'-t? ro ~ t:tto::"ing as Ie _ as ani:naJ., con-",reyor, an ot.he~ systems of rnil gatheri?1.g. ~ho l)urpo~e of this invosti-gation is, as outlined in Progress ,~ort 1, to studT . Q analyz0 v rious systems nov.: in. u"'e El.I1d to derivQ cor..cl :cicn .... tllcrcfrom.]

Jan 1, 1941

By Edward Keller

The work covered by this report was undertaken at the request of Dr. J. A. Holmes, late Director of the Bureau of Mines, to whom the writer had been recommended by C. W. Goodale and E. P. Mathewson, of Butte and Anaconda, Mont. The director's offer was accepted for the honor it conferred and for the useful results that might be promulgated by the work in the technical field covered. The investigation was facilitated by permission to visit various works and sometimes by contributions of important definite information on a given subject. It is therefore with pleasure that acknowledgment of courtesies is made to the following corporations and gentlemen: Anaconda Copper Mining Co., Raritan Copper Works, Baltimore Copper Smelting & Rolling Co., United States Refining Co., American Smelting &, Refining Co., B. B. Thayer, A. C. Clark, A. L. Walker, William H. Peirce, E. A. Cappelen Smith, H. H. Alexander, F. C. Newton, S. Rolle, R. W. Deacon, N. W. Pierce, O. C. Martin, C. N. Sappington, James K. Thomson, W. G. Derby, and the assistants of the writer, K. W. McComas and W. L. Raup. In this report considerable space has been devoted to general and theoretical principles on the ground that under modern conditions the best results in any field of activity can be attained only with the a. id of an adequate knowledge of the best theories underlying the practice. The diffusion of such knowledge in the field of sampling metallic metallurgical materials appears to have been quite insufficient, and it is felt that when the principles involved are once thoroughly comprehended their universal application will be appreciated, so that it will make no difference whether pig iron or gold bullion is offered for test. It may further be noted that a discussion of the theories underlying practical methods is placed under the caption "Practical Sampling," with the idea that no one can be a practical sampler unless he is capable of analyzing his methods. No attempt has been made to advocate any one method, but it is hoped that the analyses of all of the methods in use will show where each may be correctly and safely applied. The fact that it is possible to demonstrate the theoretical correctness of several methods indicates the invalidity of the claim that any single one of them is the standard.

Jan 1, 1916

By Albert L. Toenges

[The i~ ortance o~ S3~e, fdequnt, nQ economical tr~n~po~t~t on 8ys~em Th~a bee~ e~~~~siz8d by the introduction of mechanical loading in co 1 mines, pa.rticula:c y \'r~ e::-e ~o?oile loaciine; ~ac~ine!;j rrre u .... ed. This papar i tr_e . eco:1d or' ?. ~eries deGcribi 1{) t:;'~~11>ort:ltion G stems et1-p oyed in mech3JlizeG. f!lincs. Progre,-s ?. epo~ t J...2.t deal t ~~tirel.: ,'Ii th the l:se of rail .laulagr £or c;atl:erine tran~ortc;tion, ailc, in t-!is paper 'Ii 11 be i acuss d c .icilY rub"col'-t? ro ~ t:tto::"ing as Ie _ as ani:naJ., con-",reyor, an ot.he~ systems of rnil gatheri?1.g. ~ho l)urpo~e of this invosti-gation is, as outlined in Progress ,~ort 1, to studT . Q analyz0 v rious systems nov.: in. u"'e El.I1d to derivQ cor..cl :cicn .... tllcrcfrom.]

Jan 1, 1941

By D. A. Elkins

This report is the second of a series of three that will evaluate, in order, the metallothermic, carbothermic, and electrolytic methods of magnesium production. The historical development of the carbothermic process is outlined. Production costs varying from 38.9 to 21.8 cents per pound of magnesium are estimated for different versions of the process. Additional suggested process modifications are listed. The technical and economic potential of the different versions are compared. Areas deemed most promising for future research on the process are delineated.

Jan 1, 1967

By R. A. Isberg

This report describes the design and implementation of UHF radio and closed-circuit television systems in the Black River room and pillar limestone mine near Butler, Pendleton County, Kentucky. Prior to designing the radio system, measurements of signal attenuation on 812 and 466 mHz were made in the slope tunnel and in the straight and level crosscuts in the mine. Two distributed antenna systems fed by two sets of base stations provide approximately 75o coverage of the mine. Passive reflectors are used for extending signals into intersecting crosscuts and two-way signal boosters will be used to extend signals to the perimeter and obstructed areas of the mine. Fourteen mine vehicles were equipped with mobile radios equipped with digital identification, alarm and status encoders. Fifteen portable transceivers also were used. Six closed-circuit television cameras provide surveillance of critical transfer points of the belt conveyor system, and the loading dock at the base of the slope and an ash disposal area in the mine. Two-way radio communication and closed-circuit television have saved considerable man. hours, increased production, reduced maintenance costs and enhanced safety. Innovative developments were the use of passive reflectors and two-way signal boosters for extending signals into intersecting crosscuts, development of lightweight signal margin measuring equipment, modifications of mobile digital encoders to automatically send status information from mine vehicles such as numbers of loads of ore delivered, hot engine, etc., and the use of CATV technology for multiplexing audio, digital and video signals onto coaxial cables from the surface to the mine.

Jan 1, 1981

By D. A. Elkins

Design plans and detailed cost estimates of mining and treating ore from Maggie Canyon deposit by two alternative methods which can be used in the event of a sudden need to exploit this resource are given . Lower costs are estimated for the operation employing oil - emulsion flotation . The total capital investment required for this operation is estimated at $ 11,750,000 . Assuming an 85 percent recovery in mining , 55.6 pct of the manganese in the ore reserve would report in 153,333 tons of ferromanganese containing 75 pct manganese . The production cost for the 5 - year operation would be about $ 245 per ton of ferromanganese . The total annual operating cost would be approximately $ 7.5 million , distributed , in pct , as follows : Mining 11.9 , milling 24.4 , sintering 9.9 , smelting 47.2 , hauling ore and sinter 2.8 , and general offices 3.8 . Recovery and costs are both higher for the operation employing dithionate leaching . In this operation the required investment is about $ 17,220,000 . Manganese recovery would be 67.6 pct in 186,160 tons of ferromanganese . Production cost would be about $ 284 per ton of ferromanganese . The total annual operating cost would be about $ 10,575,000 , distributed , in pct , as follows : Mining 8.4 , milling 44.4 , sintering 7.4 , smelting 34.7 , hauling ore and sinter 1.3 , and general offices 3.8 . Potential process modifications might reduce the operating cost of the first operation by as much as 7 pct and that of the second operation by as much as 9.5 pct , but exploitation of the deposit by the techniques studied is not economical today .

Jan 1, 1964

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006

By R. A. Plumbridge

The Honourable Mr Molefe, Premier of the North- West Province; Or Scot-Russel, Chairman of the CMMI's XV Congress; Mr Loton, Chairman of the CMMI; distinguished guests, ladies and gentlemen. At the outset may I express my sincere appreciation to the organisers of this Congress for their kind invitation to me to participate in the plenary session. May I also thank the CMMI for inviting me to be their fifth distinguished lecturer. This is a signal honour and one which is sincerely appreciated by my Group and myself. The subject of gold is a very emotive one. It conjures up different images in the minds of a wide variety of people. For many of us it is very simply the ultimate metal. In ancient times gold was sought after and treasured; it was the chosen metal for adornment and many of the best preserved artefacts of that time were hand-fashioned from gold which had been won by primitive mining techniques. Gold's rarity and its value was recognised by those who fashioned the earliest gold coins thus underlining gold's special place as a store of value.

Jan 1, 1994

By F. C. Foshag, P. E. Wingrove

The Kayford, Boone and Nicholas Division of Bethlehem Mines Corp. operates a modern coal preparation plant in Van, WV. Since start-up of the Van plant in 1976 until the summer of 1980, the refuse handling system proved to be a costly maintenance problem and a material handling bottleneck. During the 1980 two-week miners' vacation, the original system - which included two screw conveyors and a drag conveyor - was replaced by an installation using two Flexowall steep angle belt conveyors. This paper describes the technical and economic analysis that led to the new installation and reviews its first year operating performance.

Jan 1, 1983

By Jack L. Henry

The monocarbide region of the ternary system U-C-O has been investigated at 1,700° C as the first phase of a more extensive study of a portion of the four-component system U-C-O-N. An area bounded by the following compositional limits in atomic percent was studied: U, 44 to 55; C, 30 to 60; 0, 0.2 to 20. Compacts composed of mixtures of uranium, graphite, and uranium dioxide powders were sintered at 1,700° C under an equilibrium pressure of carbon monoxide to produce uranium oxycarbide specimens having a variety of compositions. Sintered specimens were evaluated by X-ray, chemical analysis, and ceramographic techniques. Solid-solution boundaries and phase relations have been established, and the effects of composition on the lattice parameter as well as the decomposition pressure have been investigated. Oxygen can be substituted for carbon in stoichiometric uranium monocarbide to the extent of about 17 atomic percent at 1,700° C. The composition range of the oxycarbide solid solution extends from about 48 to 51 atomic percent uranium in the low oxygen region. Above 10 atomic percent oxygen the composition range narrows to less than 1 atomic percent uranium. Carbon monoxide exists as a gaseous phase in equilibrium with all compositions which contain oxygen. Five separate phase fields were found bounding the solid-solution area. Other phases within this portion of the system include uranium, uranium dioxide, uranium dicarbide, and uranium sesquicarbide. Decomposition pressures of oxycarbide compositions at 1,700° C have been found to vary from a few microns for stoichiometric and uranium-rich compositions to 35 torr for carbon-oxygen-rich specimens. Lattice parameters were found to depend upon the U to C + 0 ratio as well upon the extent of substitution of oxygen into the stoichiometric monocarbide lattice.

Jan 1, 1967

By Charles W. Briggs

The steel foundries of Germany were investigated for the purpose of ascertaining (1) the type and classification of steel structures produced as castings, (2) processing methods, (3) the mechanical properties of carbon and alloy cast steels, (4) the type and character of defective castings, (5) the appearance of castings, (6) research in steel castings, and (7) plant lay-out and equipment.

Jan 1, 1946

By E. H. Crabtree

IN an ideal mill, with perfect milling operations, the mineral extraction would be 100 per cent, the, concentrate would be 100 per cent mineral, the tailing would assay zer.0 mineral and the milling cost would be zero dollars. Such an operation can, of course, never be attained. We can only strive to approach it as nearly as possible and in doing so most recognize .the fact that the three primary factors in milling: assay of concentrate, assay of tailing, and cost of operation bear a definite economic relationship to each other. This relation will change from time to time and will be different for different mills, depending on milling equipment, character and quality of feed, market conditions, and other factors. It is granted that for a given operation there is an economic point, but the location of this point is difficult. It is for the purpose of making some of these economic points a little more tangible that this paper has been prepared.

Jan 1, 1930

By S. C. Sun

A study(1) on the sulfuric acid extraction of alumina from some Pennsylvania ferruginous clays indicated that the published electrolytic method(2)(3) seems to be more efficient than the known chemical methods (4-9) for removing iron from the leach liquor. The main disadvantages of the chemical methods are the consumption of excessive amounts of reagents and/or the precipitation of prohibitive amounts of aluminum. In the electrolytic method, iron is deposited on the mercury cathode, while aluminum is not and remains in solution. This method, however, had been handicapped by the lack of an effective and economical way to purify the contaminated mercury cathode.(7)(l0). Described herein is a scheme for cleaning the mercury cathode, and for recycling the clean mercury back into the electrolytic cell. Armed with such an apparatus, the effects of applied potential, temperature, and operation time on the electrolytic separation of iron from aluminum sulfate solutions were determined. For the sake of comparing results, a term, removability, was coined to represent the percentage of iron amalgamated per unit height of electrolyte (cm.), per unit surface area of cathode (cm.2), per unit of operation time (second).

Jan 1, 1968

By Lyman Moore

This Bureau of Mines report describes 2nd evaluates iron ore resources in California and Nevada and analyzes the California and Japanese iron ore markets in which these resources will be used. The competitive position of California-Nevada ores, in these markets, was estimated by comparing regional iron ore prices, production costs, and transportation costs with those of foreign suppliers. Resources were determined to be sufficient to produce the equivalent of 585 million tons of 64-percent iron pellets at a price of less than $15 per ton delivered at California ports. Much higher tonnage could be produced at higher prices. Iron ore requirement of the California iron and steel industry will increase to an estimated 15.9 million tons by the year 2000. A study of the iron ore production potential of California-Nevada deposits and of out-of- State sources indicated that this ore requirement can be supplied most economically by California-Nevada ores. Iron ore import requirements of the Japanese iron and steel industry will increase to an estimated 150.0 million tons by the year 2000. A study of price trends in this market indicated that very little California-Nevada iron ore will be sold in Japan after 1973 when existing sales contracts expire. Iron ore-exports might be economically possible if ore could be transported from California to Japan at ballast rates as backhaul on existing petroleum shipping.

Jan 1, 1971

Jan 1, 1988