Search Documents

By Q. Cheng

This paper introduces the multi fractal interpolation method (MIM)developed for handling singularities in data analysis and for data interpolation. The MIM is a new moving average model for spatial mapping and interpolation. The model decomposes the raw data into two components: singular and nonsingular components. The former can be characterized by a localized singularity index that quantifies the scaling invariance property of measures from a multifractal point of view. The latter is a smooth component that can be estimated using ordinary kriging or other moving average models. The local singularity index characterizes the concave/convex properties of the neighbourhood values. The paper utilizes a binomial multiplicative cascade model todemonstrate the generation of one- and two-dimensional data with multi-scale singularities which can be modelled by asymmetrical multifractal distribution. It then introduces a generalized moving average mathematical model for analysing and interpolating data with singularities. Finally, it is demonstrated by a one-dimensional case study of de Wijs’ data from a profile in a zinc mine, that incorporation of spatial association and singularity can improve the interpolation result, especially for observed values with significant singularities.

Jan 1, 2015

In this study, numerical simulations of yield pillars employing the finite element method with time-dependent Drucker-Prager material model are conducted. The stress control mechanism of yield pillars on weak floor strata is studied. The development of pillar yield zone, the distribution of pillar stress and the development of failure zone in the weak floor strata are investigated. The study indicates that a properly selected yield pillar size may significantly reduce the peak stress induced in the weak floor strata and effectively control the development of failure zone in the floor.

Jan 1, 1999

By Anselmo Monteiro Ilkiu

No presente trabalho será apresentado um modelo matemático para a análise da instabilidade plástica de um cilindro de parede fina sujeita a pressão interna, considerando o material com anisotropia normal R no estado plano de tensões. As equações foram obtidas, com base nas teorias elásticas e plásticas, considerando o critério de escoamento de von Mises no estado plano de tensões em termos da anisotropia normal, e de acordo com os trabalhos realizados por Johnson & Mellor [1], Chakrabarty [2] e Al-Qureshi [3].

Aug 16, 2017

By Michel G. Grenier

Compliance with Diesel Particulate Matter (DPM) exposure regulation is currently performed using timeweighted average (TWA) sampling on underground mine workers. These samples are collected in the span of an entire shift and the resulting concentrations are compared to a legislated exposure limit. While this is very useful to determine the exposure level of an individual to DPM, it fails to clearly identify causes of exposure and highlight opportunities that could help reduce the exposure of workers in the course of the work shift. Real-time DPM monitoring measures the worker?s exposure as a function of time and helps identify circumstances where corrective actions can be taken or design changes can be made by the individual or the employer to reduce the overall exposure of the worker and peers. This work focused on obtaining DPM concentrations using a real-time polycyclic aromatic hydrocarbon (PAH) monitor. The aim was to demonstrate that this instrument, while not a direct DPM analyzer, was able to provide a concentration profile that could easily be linearly correlated to standard TWA elemental carbon measurements. In addition, several instances of improvements that could be implemented to reduce the exposure of underground employees were demonstrated.

May 1, 2010

By Cristian Rodriguez, Tom BoBo, Maria Rocha, John Kemeny

Blast fragmentation depends on many factors. First of all, it depends on the specific blast design, which includes the amount and type of explosive, the blasting pattern, the timing and sequencing, and other parameters. Secondly, it depends on the properties of the rock mass, including the uniaxial compressive strength (UCS), the rock mass elastic modulus (E), the rock discontinuity characteristics (as reflected in the GSI or RMR), and the rock density. Several fragmentation models have been proposed to predict blast fragmentation based on the blast design and the properties of the rock. These models include the Kuz-Ram model and variations of this model, as well as recent models by Kim and Kemeny (2011) and others. Fragmentation models are validated and calibrated by comparing the predicted fragmentation with actual post-blast fragmentation from image processing monitoring systems.

Jan 1, 2014

By Mike Turner

The Otter-Juan mine was closed by WMC Resources? Kambalda Nickel Operations (WMC-KNO) in 1999 due to the combined effects of low Nickel prices and high mining costs. GBF Mining Pty Ltd purchased Otter-Juan Mine from WMC in early 2001 as part of WMC?s disinvestment from the nickel mines in the Kambalda area. Goldfields Mine Management (GMM), (a wholly owned subsidiary of GBF Pty Ltd) re-opened Otter-Juan in May 2001. The Otter-Juan mine is one of the oldest mines in the Kambalda region and is now mining at depths below 1160mbs. Stresses are very high, rock mass deformation considerable, and the mine has a history of serious seismic activity. Orebody widths in the current mining area range from 2 to 2.5m, with dips from 25° to 40°. On taking over the operation, GMM converted the mining method from the previous mechanised drift and fill method to a slot-rise and strip method using hand held airlegs. During the latter years of production under the control of WMC, production averaged around 12000 tonnes per month, with grades of 2.7% and orebody extraction of only 55 to 60%. In the last three years of operation under the control of GMM the mine has produced an average of 12000 tonnes per month of ore at an average grade of 4.2% and with an orebody extraction of 70 to 75%. The mine is now highly profitable with at least another 3 years of reserves remaining at depth. The main benefits of the current method include reduced dilution and increased extraction. In the relatively poor ground conditions experienced this has only been possible using airleg mining, with excavations designed to suit conditions, support to suit rockmass deformations, and with improved extraction sequencing. Other benefits have included improved operating conditions, reduced falls of ground incidents and a dramatic reduction in seismic activity. These achievements have only been possible by stepping back in time and using traditional airleg stoping methods to extract the maximum amount of the orebody with minimum dilution. This paper includes details of the mine history, geology, mining method, seismicity, and support.

May 1, 2004

By Robert Alperstein, Nidal AbiSaab, Joe Pastore

"This paper describes the design and construction aspects of the foundation support for a 57-story building currently under construction in lower Manhattan. The site is located near the East River with subsurface conditions consisting of about 40-ft [12.2-m] of unsuitable historic fill and soft plastic clay underlain by about 130-ft [39.6-m] of dense sand resting on bedrock. A mat foundation supported on unsuitable soils improved by jet grouting was selected for the project. Design concepts and selection of the engineering properties of the improved and natural foundation soils are discussed. The results of quality control testing and methods to verify design parameters during construction are presented.INTRODUCTIONNew York City (especially Manhattan) is known for its skyline of high rise structures. The geologic conditions in the New York Metropolitan Area influence the selection of foundations and feasibility of high rise construction as noted by Horvath (2013). These conditions include varying depth and quality of bedrock, multiple glacial events during the Pleistocene Epoch, and the effects of human modifications to the subsurface environment. Clusters of relatively taller buildings are generally located in Lower and Midtown Manhattan where sound crystalline bedrock is at relatively shallow depth beneath the ground surface and shallow foundations rest on the bedrock surface. In recent years the use of more costly high capacity driven piles or drilled caissons and deep basements has enabled the high skyline to spread to other areas."

Jan 1, 2016

By Steve Kral

It seems that mining has been in the doldrums for awhile. Except for gold, metals prices remain depressed. And economic conditions in the United States and around the globe have put governments in a financial bind. This affects new building and infra-structure repairs, which, in turn, have a major impact the building materials industry. Add to that the severe environmental and regulatory restrictions placed on the mining industry in developing new mines and expanding existing ones. It’s enough to make a mining engineer/geologist/metallurgist go sell real estate. So why do those employed in the mining industry stay in the business and remain optimistic? Many of them will say that they have been through down cycles before and know that an upswing is in the offing. They also know that society will always need the commodities they produce. And they love the challenge. The challenge in mining’s case is producing commodities as cheaply as possible, in an environmentally sound manner and improving the quality of life in the communities where they work.

Jan 1, 2003

By M. M. Cole

An assessment of the combined application of remotely sensed satellite imagery, geobotany and biogeochemistry reveals the complementary value of these techniques in the Thalanga area. The SPOT imagery yields useful information on features of the terrain and discriminates the gossan over the ore zone. Geobotany differentiates geological units and the anomalous vegetation provides visual expression of the surface presence of the ore zone, while biogeochemistry effectively locates its concealed extension below Tertiary sediments and ferricrete

Jan 1, 1991

By Víctor Guimaraes

El presente texto señala las estrategias de planteamiento de minado en la minera Tintaya con el objetivo de maximizar el valor neto de la operación minera y a un nivel aceptable de riesgo. Este ciclo de planeamiento, evalúan diferentes alternativas dentro de los siguientes procesos como: optimización del pit (Uso de ley corte durante el proceso, diseño de taludes, Pit descontado, inclusión de nuevos procesos metalúrgicos y de recursos inferidos), generación de fases de minado (Parametrización de fases), programación de la producción (uso de optimizadores basados en programación lineal), planeamiento de desarrollo mina (incluye planes de drenaje subterráneo y superficial), Planeamiento corto plazo y actualización del plan de cierre.

Sep 9, 2007

By N Elith

Coal is a valuable energy source in New Zealand and has been mined from the West Coast for over 100 years. Stockton Mine is New Zealand's largest opencast coal producer supplying around 1.5 Mt of hard coking and thermal coal to international markets annually. The Stockton Plateau forms an extensive, gently inclined dip slope on erosion resistant Lower Eocene Brunner Coal Measures unconformably overlying basement rocks. The dip slope rises 600 - 1000 masl, locally dissected by fault scarps and present-day fluvial systems, some of which are deeply incised. Within the Mt Augustus Mining Block overburden comprises of a 30 - 40 m thick sequence of fluviatile, coarse to granular coal measure sandstones. High quality coking coal is preserved as a gently dipping, 10 - 12 m thick seam. High and sometimes very steep cliffs of jointed overburden shape the skyline escarpment, above steep forested slopes and gullies. As mining has progressed at Mt Augustus individual coal blocks are progressively becoming more technically challenging. This paper outlines the scientific approach taken by Solid Energy International and mining contractors to carefully unlock many thousands of tons of coal whilst protecting nearby flora and fauna from the impacts of dislodged rock and other blasting side-effects. The strategy involved: an expert-driven onsite risk assessment,formulation of a management plan to manage impacts,conducting an in situ vibration research program, andanalysis of results and operational designs to eliminate potential environmental problems.

Jan 1, 2003

By Yves St-Amour, Vince Luongo

This paper will discuss one of the largest construction projects the City of Portland has undertaken. This phase of the Willamette River Combined Sewer Overflow (CSO)project consists of approximately 18,500 ft of tunnel in soft ground, requiring the construction of six deep shafts and jet grout ground improvement. The purpose of the project is to reduce volume of combined sewerage overflows from the drainage areas on the west side of the Willamette River. Bencor-Petrifond-Pacchiosi Joint Venture was awarded a contract to design and construct six deep circular shafts, jet grout ground improvement for three bridges and jet grout ground improvement break-in/outs for some shafts. Of the six shafts the Pumping Station Shaft was the deepest and largest, requiring a permanent ground support system with a deep jet grout ground water cut-off to 335-ft deep. The joint venture used state of the art methods and equipment to achieve its objectives and build the structures through some very difficult alluvial soils to great depths next to the Willamette River. The paper will provide a general discussion of the shaft construction and jet grout ground improvement installed for this phase of the project. It will also discuss some of the technical challenges encountered while effectively managing risk and costs, resulting in a successful project completed in a timely manner.

Jan 1, 2005

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters ? usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

By Richard Kastner, Emilie Vanoudheusden, Fabrice Emeriault, Jacques Robert

INTRODUCTION The subway line B of Toulouse (France) has been realized with three different tunnel boring machines (TBM) techniques: Contracts 2 and 5 are excavated with earth-pressure balanced TBM, Contract 4 with a slurry shield TBM, and Contract 3 with a compressed-air TBM. The first three machines are around 7.7 m in diameter, while the last one is 5.3 m. Moreover, a small part of the line (50 m) has been excavated by a conventional method. The tunnels run through the Toulouse molasses, composed of hard sandy clay with pockets and lenses of dense sand. Geotechnical investigations have shown that in these formations, K0 is greater than 1, around 1.8 at a depth of 25 m (Serratrice,2005) and that geotechnical characteristics are homogenous on the whole layout (? =22 kN/m3, Su = 300 kPa, c' = 30 kPa, F' = 32°). The water table is found between 2 and4 m below ground level. As geology, stratigraphy and tunnel cover (between 10 and 20 m) are almost identical, a comparison of movements induced by the excavation by each of the four excavation techniques is possible. This paper presents the soil mass movement measures in the case of the conventional excavation method and in the case of TBM sections. It shows how tunneling parameters may explain the different surface movements observed during excavation. For the sake of simplicity, only the results of Contract 2 (earth pressure balanced TBM)will be presented. MONITORING Monitoring for the Conventional Method Section For the conventional method section (Vanoudheusden et al. 2005) the mass soil movements are measured with two inclinometers and one multi-point extensometer borehole with automatic data acquisition (Figure 1). The monitoring devices include

Jan 1, 2007

By J. A. Caldwell, G. E. Blight

The metropolitan area of the Witwatersrand has grown up around the Witwatersrand gold mines. Most of the mines have now been abandoned, but deposits of waste material remain and have been surrounded, and in some instances covered, by urban and industrial sprawl. This paper describes the development of geotechnical measures for the abatement of air and water pollution from abandoned gold-residue dams in the Witwatersrand area. The measures include the stabilization of the surfaces of the dams to prevent wind and water erosion, the terracing of slopes to minimize erosion, and the construction of catchment walls and dams. The measures were developed in terms of the set of guidelines for environmental protection adopted by the Chamber of Mines of South Africa in 1979.

Jan 1, 1983

By Carel Robinson

THE little coal mine at Otsego, in the Winding Gulf field of southern West Virginia was dying. In the history of coal mining thousands of mines have been successful at first, but usually a change occurred and profits ceased. Often be change was so gradual and extended over such a length of time that the fundamental causes did not stand out in sharp relief and their significance was not realized. Studies often reveal that the cause for failure was in the arteries that connect the producing places with the mine entrance. Profits continued so long as the working places were close to the tipple and while the thrill of newness aid ease of access resulted in effective supervision from day to day. The air- way and haulageway, the wire line and manway, may have been sufficient when the distance from the entrance was a few hundred feet, but were inadequate when this was extended for thousands of feet.

Jan 1, 1937

By Moi Arzamendi, Jose Ramirez, Kenneth Kniss, Sunil Arora, James Gingery

Construction of a new approach embankment for a railroad bridge over a river in Southern California required placing up to 12 ft of fill over soft to medium stiff silts and clays along an approximate 1,500-ft long stretch. The embankment, situated within a narrow railroad right-of-way between an existing live track and existing buildings, would have been susceptible to excessive settlement that could damage existing buildings and numerous underground utilities if regular weight soil fill had been placed over the unimproved ground. To limit total and differential static settlements to tolerable levels, a design was developed using a combination of mechanically stabilized earth wall with lightweight cellular concrete fill and rigid inclusions ground improvement. This paper describes the design of the ground improvement system, construction methods used, and challenges of working next to live railroad traffic. Ground improvement quality control and assurance measures, and verification of performance by settlement monitoring are also addressed. INTRODUCTION AND BACKGROUND The 0.9-mile San Diego River Double Track (SDRDT) project is located on the Los Angeles-San Diego- San Luis Obispo (LOSSAN) Corridor in San Diego, California. The project includes the replacement of the existing 900-ft long single track railroad bridge over the San Diego River with twin double track structures. Construction of the project is phased and closely coordinated with the associated Mid-Coast light rail project (San Diego Trolley Blue Line Extension). The new bridge is a 7-span, twin steel, through girder structure supported by six cast-in-place reinforced concrete pier caps and two abutments. The large diameter cast-in-drilled-hole (CIDH) foundations are up to 9 ft in diameter, with upper portions encased in a 1.5-in.-thick permanent steel casing. The north abutment approach embankment includes a mechanically stabilized earth (MSE) retaining wall up to approximately 10 ft high and 1,520 ft long. This paper focuses on the design and construction of the north approach embankment. The project site is characterized by challenging geotechnical and seismic conditions. The site contains liquefiable soils interbedded with soft cohesive soils, underlain by competent layers of sand/gravel/cobble and other sedimentary formations. Static settlement of the new railroad, crossing utilities and adjacent buildings was a primary design concern for the north approach embankment.

Jan 1, 2018

By P. Brad Marchant

"To properly evaluate bioleaching as a commercial alternative for sulphide concentrate oxidation, to enhance cyanidation response, it was necessary to define and optimize critical operating variables outside of the laboratory under less than ideal conditions. A complete bioleach testing laboratory was installed at Equity Silver Mines to aid in pilot plant flowsheet development.A continuous pilot scale bioleach circuit was constructed to provide data for meaningful valuation of biotechnology on a plant scale. The important operating and design parameters for pilot plant testing are described. Plant scale feasibility and design considerations, to treat a refractory pyrite/arsenopyrite concentrate produced from flotation tailing, are discussed. 1.0 BACKGROUNDEquity Silver Mines Limited is located 37 km southeast of Houston in central British Columbia. A 70% owned subsidiary of Placer Development Limited, Equity is Canada's largest open pit silver producer. Ore reserves were estimated at 28 million tonnes grading 106 g Ag/t, 0.96 g Au/t, and 0.38% Cu from two pits, the Southern Tail and the Main Zone. Detailed geology and mineralogy has been described previously(1,2).The concentrator flowsheet consists of conventional crushing, grinding, flotation, and dewatering circuits processing 5 300 tonnes per day of new mill feed. The resultant Cu/Ag/Au concentrate is trucked to Prince Rupert for shipment to market. Mill tailing reports to a closed circuit pond from which mill process water is recycled. Details of the concentrator process have been reported( 2,3).Production in the Southern Tail pit, from July 1980 to March 1984, resulted in mill tailing averaging 0.9 g Au/t and slightly more than 20 g Ag/t. Historic data indicate that unrecovered gold is associated with arsenopyrite and silver losses with unliberated tetrahedrite or minor silve,, bearing sulphosalts. Main Zone mill tailing, which commenced production in March 1984, contains approximately 0.5 g Au/t which is probably associated by majority with silver bearing minerals and pyrite while silver losses, 30-40 g Ag/t, are associated with unliberated silver and antimony bearing minerals."

Jan 1, 1985

By Li Keqiang

Among the pile foundations of the 156 tall buildings over 18 storeys in Shenzhen, 86. 5% of them are constructed by slurry drilled piles, bored piles and excavated piles (hand-dug caissons). Based on the experiences of the engineering practices, the paper points out that the main quality problems of pile foundations in Shenzhen are: insufficient bearing capacity of single pile; poor concrete quality of pile; damage of the precast pile; pile tip not reaching the required bearing stratum and the thickness of bored/drilled sediment exceeding the specified. etc. The quality inspection methods that have been used include: check of construction records and excavating; static loading test; core sampling test; non-destructive test, etc. Treatments of quality problems used in Shenzhen are also introduced in this paper.

Jan 1, 1991

By Sergio N. Monteiro

Jute fiber reinforced polymer composites are among the most investigated and applied natural composites. In this past decade the mechanical properties of these composites has been assessed for various types of test conditions. However, the reported results correspond mainly to short-cut jute fiber composites, which do not present the highest mechanical strength as compared to continuous fibers of the same kind. In order to complement these results, the present work evaluated the mechanical behavior, by means of flexural tests, of polyester matrix composites reinforced with continuous jute fibers. Bend tests were conducted in standard specimens with up to 40% of jute. Fracture analysis by SEM displayed the rupture mechanisms. The results showed an improvement in some flexural properties with incorporation of jute fiber. However, a low fiber/matrix interfacial stress was responsible for limitation in the values attained by some properties.

Jan 1, 2010