Search Documents

By Phillip Cancilla, Daniel Roy, Frank Rosenblum

"The manual moisture determination methods employed today by mineral processing plants falls short in providing timely information required for automation control. The costs associated with transporting and handling concentrates still represent a major portion of the overall treatment price. When considering the cash flow of a mining operation, that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, an efficient method of on-line moisture content would be a welcome tool.A novel on-line determination system for ore concentrate moisture content would replace the normally tedious classic manual procedure. Since the introduction of microelectronic-based control systems, operators have strived to reduce the treatment costs to the minimum therefore a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the “wish list” of mineral processors since the problem has always been that you can only control what you can measure. Today, the task of moisture determination is still done in the classical technique of loss in weight by uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of 7 to 9%. Many times, delays in manually achieving reliable feedback on the moisture content results in the moisture varying from 5 to 12% before corrective actions can be made.This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principals and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper describes a unique and promising on-line moisture sensor in two mineral processing applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimization of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented to indicate the usefulness and to summarize the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content."

Jan 1, 2001

By Gruenewaldt von

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. The principles of shear-driven aggregation of particulate matter suspended in fluids, a common industrial method of concentration and separation, were applied to a convecting magma to estimate the time required to sparge or strip the PGE and Cr content and concentrate it into the boundary layers. It was calculated that an ore-grade (e.g. 6 ppm PGE) boundary layer about 1 m thick would require 100 000 years at most to form from a body of magma 500 m deep with a PGE content of 20 ppb. Since concentration would be most vigorous when the magma was warmest, at least half of this concentration would take place in the first 10 000 years. The effect of dispersive pressure in the boundary layer would generate a concentration high of refractories just below the top of each boundary layer and another just above the bottom. If the magma was a double-diffusive system, it might evolve by the downward cascade of enriched boundary-layer material into the hotter, lower magma layers, where depending on saturation levels chromites would equilibrate and sulphides undergo partial or total resorption, enriching PGE levels in any remaining sulphides. This cascade process would in time greatly enrich the lower regions in PGE-bearing sulphides and chromites

Apr 1, 1994

By Thomas L. Vandergrift

To significantly increase the stability of underground excavations while exploiting the full advantages of confined rock strength, methods must be developed to actively control the distribution of stresses near the excavation. This U.S. Bureau of Mines study examines theoretical and practical aspects of rock pres¬surization, an active stress control concept that induces compressive stress in the wall rock through repeated hydraulic fracturing with a settable fluid. Numerical analyses performed by incorporating the rock pressurization concept into a variety of boundary-element models indicate that rock pressurization has the potential to improve underground excavation stability in three ways: (1) by relocating stress concentrations away from the weak opening surface to stronger, confined wall rock; (2) by inducing additional stresses in a biaxial stress field to reduce the difference between the principal stress components near the surface of the opening; and (3) by counteracting the tensile stresses induced in the rock around internally loaded openings. Practical aspects of the rock pressurization concept were investigated through a series of hydraulic fracturing experiments. The use of sulfur as a settable fluid for hydraulic fracturing was demonstrated, although problems related to sulfur viscosity suggest that other molten materials, such as wax, may be better suited to practical field application of the rock pressurization concept.

Jan 1, 2010

By Bruno Bussière

Le drainage minier acide (DMA) provenant de la circulation des eaux à travers les rejets miniers sulfureux est sans doute le principal problème environnemental auquel est confrontée l?industrie minière. Afin de prévenir les problèmes environnementaux reliés au DMA, on doit restreindre la présence de l?une et/ou de l?autre des principales composantes menant à la production d?acide, soit l?eau, l?air et les sulfures. Pour ce faire, différentes techniques ont été proposées au cours des dernières années, dont la désulfuration environnementale et les couvertures avec effets de barrière capillaire (CEBC). Dans ce papier, on propose d?utiliser ces deux techniques en combinaison. Ainsi, on produirait un rejet désulfuré à l?usine de traitement qui pourrait, par la suite, être utilisé comme matériau pour la couche de rétention d?eau de la CEBC. Dans un premier temps, on présente les résultats d?une étude de laboratoire qui montre qu?il est possible de désulfurer les rejets de concentrateur à l?aide de la flottation non sélective jusqu?à l?obtention d?un résidu non générateur d?acide. Par la suite, des essais en colonne ont permis de démontrer qu?il est possible de limiter la production de DMA d?un résidu sulfureux à l?aide d?une CEBC dont la couche fine est constituée de résidus désulfurés. Des prédictions théoriques estiment même que la présence de sulfures résiduels dans la fraction désulfurée utilisée comme matériau pour la rétention d?eau peut avoir un effet bénéfique en réduisant la migration d?oxygène. En effet, les sulfures contenus dans la couche de rétention d?eau peuvent consommer l?oxygène qui tente de migrer vers le bas et, ainsi, réduire les flux d?oxygène qui atteignent les rejets réactifs.

Nov 1, 2002

Gas well tests were performed on 17 wells in the Roma area. The procedure used in the test programme incorporates an initial isochronal test followed by what is described as the "two flow drawdown" technique. The second flow of the two flow drawdown test was conducted for sufficient time to allow transient investigation of the surrounding reservoir. This combination of tests allows the evaluation of stabilized production capacity in addition to the determination ,of several important reservoir characteristics.It also provides a qualitative indication of reserves, by reflecting the presence or absence of reservoir boundaries within the drainage area affected during the test.

Jan 1, 1968

By H. C. Seeber

When considering all the aspects of a viable mine plan, it is important to estimate the accurate cost of mine ventilation, which varies as a function of airway dimensions, fan selection and ventilation network. Optimization of the overall elements of ventilation design can lead to very significant cost savings when capital and operating cost savings are considered in combination. This paper will describe a methodology, whereby ventilation costs can be minimized by optimizing the ventilation aspects of mine design and fan selection, by providing a brief description on ventilation theory and the factors which affect ventilation operating and capital costs.

Jan 1, 2002

By K. H. J. Clarke

SINCE the beginning of this century the non-ferrous mineral industry has contributed $17,809,-000,000 to the economic growth of Canada. To contemplate the vast amount of investment capital required and the resultant beneficial distribution of these billions of dollars for labour, transportation, supplies, taxes and dividends, challenges the imagination. It is the purpose of this paper, (a) to trace the development of the industry since its formative period to the present; (b) to discuss the current situation and problems; and ( c) to attempt to peer into the hazy future. Although there are 21 metals currently being produced in Canada which are classified as non-ferrous, or as alloying metals, copper, lead, zinc, nickel-the metals which will be discussed in this paper-constitute almost 60 per cent of their total value. ;The story

Jan 1, 1961

By Y. Q. Li, Z. C. Shen, C. H. Zhao

The dynamic properties of the KYF-320 flotation machine which is one of the biggest flotation machines in the world were tested and then verified by the computational fluid dynamics (CFD) simulation. Aeration rate testing results suggest that he effect of circulation holes on the fluid state in the flotation cell becomes gradually smaller when the impeller speed is greater than 107 r/min. The dispersion degree of air increases with the increasing impeller speed and decreases with the increasing aeration rate, and it increases slightly when the impeller speed is greater than 107 r/min. The air holdup increases and then decreases with the increasing impeller speeds and aeration rates, and a maximum value of air holdup is shown at impeller speed of 107 r/min with a value of 12.28%. CFD simulation results are in good agreement with these testing results. Industrial-scale test was carried out using this 320 m3 flotation machine for the flotation of Cu ores. The results show that Cu content increases from 0.06% of crude ore to 1.26% of concentrate, and the S content increases from 0.39% of crude ore to 24.83% of concentrate. Moreover, using this flotation machine 5.88% of power is saved compared to other type of large flotation machine.

Jan 1, 2015

By Floyd Varley

In deep and highly-stressed coal mining, advanced design practices are used to minimize the potential for damaging events to occur. Despite these design efforts, the hazard of coal mine bumps can not be completely eliminated. This paper will review current and historic work practices used internationally to minimize the hazard to miners from mining in conditions which could produce a bump. These site specific work practices have a common base in monitoring for conditions which could result in a bump and application of controls to prevent the occurrence or minimize the severity of an event where miners are working. Monitoring practices range from purely observational to semi quantitative. Control methods attempt to initiate events in a controlled manner, absorb the energy of a potential event or reduce the potential for or magnitude of an event by altering the stress conditions of the mine workings. Building from the experiences of other coal fields, an empirical framework to manage the potential hazard of coal mine bumps can be developed to enhance the level of safety provided by prudent mine design.

Jan 1, 2008

By George W. Huseman, W. D. Mcmillan

"INTRODUCTION Feldspars represent one of the most abundant groups of minerals and constitute nearly Go percent of the material contained in the igneous rocks. They are grouped in a series of related aluminum silicates with varying amounts of potash, soda, and lime. .Approximately 85 percent of the feldspar produced in the United States is used as a flux in the production of glass, pottery, enamel and sanitary ware, brick, and tile. Notwithstanding the abundance of feldspar in the earth's crust, the only deposits that are worked to any extent are the pegmatites or coarsely crystalline dikes where natural segregation of the constituents facilitates recovery of the feldspar with a minimum of free quartz, mica, tourmaline, garnet, and other iron-bearing minerals that are detrimental in most ceramic industries.Although there are three glassplants and numerous other ceramic industries in Texas, all of the feldspar used in these plants is from other States. In the Llano region of central Texas, however, there are numerous coarse pegmatite dikes consisting primarily of feldspar and quartz in ratios up to 3 to 1. One of the more important of these dikes is the Badu Hill deposit in Llano County, Tex., which was first described by Carl Chelf 4/ in 1942. Following an examination of the deposit by W. D. McMillan, engineer in charge of the Texas field office of the Bureau of Mines, in January 1946, a proposal was made to investigate the deposit by core drilling in cooperation with the Department of Ceramic Engineering, University of Texas. This report presents the results of the cooperative investigation, which was begun April 24, 1946, and completed May 17, 1946."

Jul 1, 1947

By Rees J. Llewellyn

Improved product development, assessment methods and evaluation studies of materials for oil sands applications have traditionally focused on low and high stress abrasion and slurry erosion resistance mechanisms, because they were considered to be the predominant wear modes prevailing in oil sands mining, transportation and bitumen recovery. More recently with the very successful introduction of oil sands hydraulic transportation systems, there has been increasing use of crusher systems in which materials of construction are also required to have good toughness and gouging abrasion properties to withstand impact and the severe indentation and ploughing forces that are involved. To assess material property requirements for mitigating this additional wear mechanism, jaw crusher gouging abrasion tests using a modified ASTM G81 procedure, have been carried out on a range of wear materials of interest for oil sands mining service. The method involves a comparison of the wear losses that occur for reference and selected test plates when a controlled amount of standard feed rock is comminuted in a laboratory jaw crusher. Among the classes of material evaluated have been Q&T plate steels, austenitic manganese steel, chromium and chromium molybdenum white irons as plain castings and in laminated forms and also chromium carbide and tungsten carbide overlaid wear plates.

May 1, 2004

By Lewis W. MacNaughton, F. L. Burchard

The North Texas district, as herein defined, includes the counties of Archer, Baylor, Clay, Coolie, Foard, Hardeman, Knox, Montague, Wichita, and Wilbarger. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, are usually modified by stratigraphic changes in the sediments. Excepting the fields in southeastern Baylor, southern Archer, and southwestern Clay Counties, all the fields within the district are on this Red River uplift. These exceptions, which have the same type of oil and gas accumulation as the other fields, are on the extreme north end of the Bend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas to Archer County. The larger part of past oil and gas production has come from Pennsylvanian strata, with less important amounts from the Permian, and minor but increasingly important quantities from the Ordovician. DevELopments during 1941 Nearly 1600 wells were drilled in the district during 1941 as compared with more than 1700 in 1940. However, the ratio of successful drilling operations was higher and some 1200 oil wells were completed. Production held about even with the previous year, as did the number of producing oil wells. Known oil reserves increased slightly throughout exploration, which generally was carried on at greater depths than in former years. The average depth of discovery wells was 300 ft. deeper than in 1940. Although discoveries were evenly divided numerically between horizons above the base of the Strawn series and those below the Strawn, the deeper horizons, including the Bend series of the Pennsylvanian, the Mississippian limestone, and the Simpson and Ellenburger of the Ordovician, furnished most of the increase in oil reserves. The largest single addition to the reserves was in the Ellenburger formation in the K.M.A. field. During the year 112 wells were completed in this horizon, bringing the total developed acreage to some 4600 acres. The Straan series in K.M.A. also received considerable development in 1941, with 114 completions. K.M.A. Pressure Maintenance Satisfactory progress was made by the K.M.A. Pressure Maintenance Association in 1941. At the end of the year, 99 wells were being used for input and total monthly volume of gas returned to the reservoir reached a high of 340,548 M cu. ft. in December from a low of 208,853 M cu. ft. in February. Total volume of gas returned during 1941 was 3,306,052 M cu. ft. To the end of the year, 150 cu. ft. of gas had been returned for every barrel of oil produced from the reservoir while the input ratio for December was 397 cu. ft. Per

Jan 1, 1942

By F. L. Burchard, Lewis W. MacNaughton

The North Texas district, as herein defined, includes the counties of Archer, Baylor, Clay, Coolie, Foard, Hardeman, Knox, Montague, Wichita, and Wilbarger. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, are usually modified by stratigraphic changes in the sediments. Excepting the fields in southeastern Baylor, southern Archer, and southwestern Clay Counties, all the fields within the district are on this Red River uplift. These exceptions, which have the same type of oil and gas accumulation as the other fields, are on the extreme north end of the Bend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas to Archer County. The larger part of past oil and gas production has come from Pennsylvanian strata, with less important amounts from the Permian, and minor but increasingly important quantities from the Ordovician. DevELopments during 1941 Nearly 1600 wells were drilled in the district during 1941 as compared with more than 1700 in 1940. However, the ratio of successful drilling operations was higher and some 1200 oil wells were completed. Production held about even with the previous year, as did the number of producing oil wells. Known oil reserves increased slightly throughout exploration, which generally was carried on at greater depths than in former years. The average depth of discovery wells was 300 ft. deeper than in 1940. Although discoveries were evenly divided numerically between horizons above the base of the Strawn series and those below the Strawn, the deeper horizons, including the Bend series of the Pennsylvanian, the Mississippian limestone, and the Simpson and Ellenburger of the Ordovician, furnished most of the increase in oil reserves. The largest single addition to the reserves was in the Ellenburger formation in the K.M.A. field. During the year 112 wells were completed in this horizon, bringing the total developed acreage to some 4600 acres. The Straan series in K.M.A. also received considerable development in 1941, with 114 completions. K.M.A. Pressure Maintenance Satisfactory progress was made by the K.M.A. Pressure Maintenance Association in 1941. At the end of the year, 99 wells were being used for input and total monthly volume of gas returned to the reservoir reached a high of 340,548 M cu. ft. in December from a low of 208,853 M cu. ft. in February. Total volume of gas returned during 1941 was 3,306,052 M cu. ft. To the end of the year, 150 cu. ft. of gas had been returned for every barrel of oil produced from the reservoir while the input ratio for December was 397 cu. ft. Per

Jan 1, 1942

By A. C. Legg, M. T. Malema

Keywords: Pyrometallurgy, flash, smelting, furnace, nickel, copper, Botswana BCL Limited operates the only Flash Smelting Furnace on the African continent, at Selebi-Phikwe, situated in north-eastern Botswana. The furnace was commissioned in 1973 and produces a high-grade sulphide matte containing nickel, copper and cobalt, which is shipped to refineries in Zimbabwe and Norway for further processing. This paper outlines the recent process improvements and plant expansions that have resulted in a capacity increase from 40 000 to 60 000 tons per annum of metal production.

Jan 1, 2006

By D. Malhotra

The economic viability of a mining operation depends on continuous process improvements. Diagnostic testing and plant auditing are essential useful tools to improve performance and reduce operating costs. Case studies are discussed to illustrate benefits of these techniques to improve plant efficiency.

Jan 1, 2001

By G Veillette, B Parker, S Hart

This paper provides a history of the challenges that were experienced while treating both the clayey oxide gold ores and the supergene copper-gold ores at the Boddington Gold Mine during the period 1989 to 2001. However the bigger challenge was to find a process flow sheet that would allow the economic treatment of the large low-grade competent gold-copper resource that underlies the oxide and supergene gold resource. Metallurgical test work and engineering studies on this resource started in the mid 1990s and culminated in the approval in 2006 of the 35 Mtpa Boddington Expansion Project to treat this material. The process flow sheet provides the basis of an energy efficient comminution circuit that includes high pressure grinding rolls and a treatment circuit with gravity separation, flash and conventional flotation to produce a precious metal low-grade copper concentrate followed by cyanide leaching of the rougher-scavenger and cleaner tailings streams. The treatment circuit allows maximum removal of copper minerals prior to cyanide leaching and so provides an environmentally responsible tailings disposal circuit.

Jan 1, 2007

By J. R. Emery, D. F. Coates

"FOUR PAPERS ON CEMENTED BACKFILL were given at the Annual General Meeting of The Canadian Institute of Mining and Metallurgy in 1970:Weaver, W. S., and Luka, R., ""Laboratory Studies of Cement-Stabilized Mine Tailings"".Pasieka, A. R., Beattie, H. F., and Espley, G. H., ""Cemented Hydraulic Backill within the Falconbridge Group of Companies"".McLeod, P. C., and Schwartz, A., ""Consolidated Fill at Noranda Mines Limited (Geco Division)"".Clement, W. P., and Sokoloski, R., ""Pumping Cemented Backfill"".These four papers give the impression of a development in mining technology that has been substantially completed. Somewhat over ten years ago, The Inter-national Nickel Company of Canada, Limited and Falconbridge Nickel Mines Limited started experimenting with the addition of Portland cement to mill tailings to produce improved backfill and cheaper floors for scraping. Shortly after, the Canada Cement Company Limited (now Canada Cement Lafarge Ltd.), with full support of the two mining companies, started an extensive research program to provide the technologic-al data necessary to exploit what was obviously going to be a significant development in mining technology."

Jan 1, 1970

Ore from the Hill 50 Gold Mine, consists essentially of pyrrhotite, with minor amounts of pyrite, chalcopyrite, galena and gold, replacing "jaspilite." The gold is associated with the sulphides as shotty particles. About 8 per cent. of the particles are less than '0.010'mm.The Hill 50 Gold Mine, at Boogardie in the Murchison goldfield, about 300 miles north-west of Kalgoorlie, was first operated in 1898. From 1898 to 1917 it yielded 20,000 short tons of ore for a recovery of 6,225' fine oz. gold, equivalent to a recovery grade of 6.22 dwt. gold per ton.The present company since the beginning of its operations in September 1936 to June 30, 1954, produced 811,081 short tons of ore for a recovery of 242,554 fine oz. of gold, equivalent to a recovery grade of 5.98 dwt. gold per ton.The grade of ore (recovery grade) has shown a remarkable variation with depth. From the 120 ft. Ievel to the 300 ft. level, it averaged about 7.5 dwt. Au per ton. Below the 300 ft. level it declined, and from 300 ft. to 400 ft. averaged 4.9 dwt. per ton, falling further with increasing depth to about 4.5 dwt. per ton at the '600 ft. level.On the 820 ft. level the grade improved sharply to about 14 dwt: per ton, and this grade has persisted down to and on the 1060 ft. level.The orebody has been described by Finucane (1953) as a series of lenses of finely banded jaspilite conformably enclosed by greenstones. The jaspilite is tightly folded and faulted and intruded by dykes of felspar porpnyry.Mineralization is practically restricted to the jaspilite.

Jan 1, 1955

By Ronald B. DeDiemar

This paper will present the intrinsic factors of a cone crusher that affect performance, develop and define an ideal feed gradation for a cone crusher and, finally, bring out an important new development in computer design of crushing chambers and show an ability to predict crusher performance without trial-and-error methods.

Jan 1, 1979

The 1990s present many challenges, not the least of which is in the area of health and safety. Integrating of safety and health into the management process to suit the overall needs of a company will require commitment. Organisations which consistently perform to high success levels do so because they plan it that way. By using tools of total quality management, the potential to continually improve all safety processes exists. The successful integration of total quality measurement principles used in the improvement of safety processes, and the measurement of performance-based activities allow for prevention of accident causing scenarios and performance improvement.

Jan 1, 1993