Search Documents

By Pat DeWilliam

The Yakobi nickel-copper deposit is located essentially at tidewater in the east-central part of Yakobi Island, about 16 1 airline km (100 airline miles) west of Juneau, and can be reached by float plane and boat from Juneau and Sitka. The fishing village of Pelican, population 400, is situated 14.5 km (9 miles) to the east. An unimproved road, approximately 4 km (2.5 miles) long, connects a dock site at Lisianski Strait with the main part of the deposit known as the Basin Area (Fig. I). Other mineral occurrences are known as the Takanis, Flapjack, and Beach Areas. Another smaller nickel-copper deposit is located about 32 km (20 miles) to the south on Western Chichagof Island and is known as the Mirror Harbor nickel-copper deposit. The original discovery of the Yakobi deposit was made by S.H.P. Vevelstad about 1920 and a 47.5-m (156-ft) long adit was driven on the southwest side of the deposit in the Basin Area. The deposit was examined by J.R. Van Fleet of Union Carbide in 1930 and by J.G. Fairchild in September 1931. Stanley and Yates of the International Nickel Co. of Canada (Inco) visited the property in August or September 1937. In 1942, the controlling interest in the deposit, covered by 124 unpatented claims, was said to be held by Vevelstad and associates

Jan 1, 1991

By R. G. Vardiman, M. R. Achter

Observations of dislocation structure in niobium are presented using two techniques. Triangular pits developed by electroetching are confined to orientations in the stereographic triangle between the (111) pole and planes of the (1ll) zone and require the presence of carbon. Some unusual electroetching phenomena at other orientations are noted. A chemical etch of dislocations decorated by the addition of carbon to 50 ppm reveals the complete dislocation line structure in a surface layer up to 30 p deep, with a resolution of less than 1 p. This effect is independent of surface orientation. The structure of subboundary nets may be resolved for misorientations up to about 1'. Dislocation structures found in strain anneal grown crystals, such as helices, prismatic loops, and high-density areas, are observed. The measurement of dislocation density is discussed and values obtained in different ways are compared. IN the course of some work on the response of refractory metals to thermal-mechanical treatments, it was desired to examine the defect structure of relatively low dislocation density crystals of niobium in bulk form. Surface and bulk methods for the observation of dislocations have been reviewed by ~melinckx,' and include etch pitting, decoration, and various X-ray techniques. The dislocation line structure has been developed by decoration in a few metals, although observations were limited to certain orientations, or by the coarseness and nonselectivity of the precipitate. The most commonly used technique is etch pitting. In niobium, etch pits have been developed chemically'0," in material of high impurity content and electrolyti-cally'' in relatively pure material. In this paper, etch pits developed electrolytically, and the dislocation line structure of a surface layer developed by decoration and chemical etching, are examined, and observations are presented from both techniques. EXPERIMENTAL METHODS Our starting material was electron-beam-melted niobium, swaged to 4 or -in.-diam rod. Chemical analysis is given in Table I. Single crystals were grown by a strain anneal technique using 1 to 2.5 pct of strain and growth temperatures of 1700" to 2300"~.'~ Some crystals grown by zone melting were also examined. The desired surface orientation was exposed either by spark machining or by sectioning with a cut-off wheel and prepared for etching by electro-polishing.

Jan 1, 1969

By McKinnon R. L

Laboratory and field work on the use of wetting agents for suppression of colliery dust is described. Although the results were inconclusive they were not discouraging and further investigation is required. The use of certain wetting agents may constitute a healthhazard.INTRODUCTIONCoal dust presents explosion and health hazards to the coal mining industry. The problem of dust suppression is particularly acute where water alone is unsatisfactory for this purpose. The addition of a surface active agent (wetting agent) to the water should enable the dust particles to be more easily wetted and thus more easily prevented from entering and spreading through the mine atmosphere.Investigations into this effect carried out at The University of Sydney mainly under research grants from The Joint Coal Board (Dawson and Hargraves, 1955; Charlton and Curnow, 1957) are summarized, and information on the possible harmful effects of certain wetting agents is given.Twelve local manufacturers and five importers supplied 52 wetting agents in liquid, solid, powder, and paste form.The active material content varied from approximately 10 per cent to 100 per cent and the cost per pound from 8d. to 14/3.LABORATORY TESTINGPossible test methodsThree methods of laboratory testing were considered.1. The standard method for comparing wetting agents is the Draves test, used in the textile industry on cotton...

Jan 1, 1961

By Pierre Pelletier, Christian Pichetie, Dany Pelletier

"IntroductionDuring 1994, Barrick Gold Corporation, or American Barrick at that period, acquired Lac Minerals Ltd. properties. One of them was the Bousquet Complex. The Bousquet Complex is divided into three distinct sites: one mine (Bousquet 2), one mill (Est-Malartic Division) and one analytical chemistry laboratory (Les Terrains auriferes).The Bousquet 2 orebody was discovered in 1986. An extensive drilling program was initiated during 1987. Its purpose was to define the orebody extent. At the end of 1997, gold production from Bousquet 2 mine reached 1 290 000 oz of gold from a cumulative tonnage processed of 4 175 000 M t.From 1980 to 1990, the Est-Malartic mill was used for the treatment of ore from the following mines: Bousquet 1, Doyon, Francoeur (Richmont mines), Buckshot and 1-20 stope. At present, the mill receives ore from the Bousquet 2 mine.HistoryThe Est-Malartic mill is located close to the town of Malartic in northwestern Quebec. The mill has been in production since the mid-1930s processing mainly clean, free mill gold ore. Active mining from the Est-Malartic mine ceased in 1979 and the mill was switched to custom processing of ore from La Mine Doyon located some 45 km to the west. This custom processing arrangement continued until 1987 when the expanded mill at Doyon became available to process all of the Doyon production. In 1987, Lac Minerals commenced development of a second mine at the Bousquet site located 40 km west of Malartic. This mine, Bousquet 2, is the down dip extension of the La Ronde mine developed by Agnico Eagle. During pre-feasibility evaluations, it was determined that it would be economically more attractive to modify the existing Est-Malartic mill than building a new facility on site. The Est-Malartic mill modifications for processing the high-copper/gold ore from the Bousquet 2 mine began in late 1989 and new circuits were commissioned in mid-1990. Modifications included the addition of both gravity and flotation concentration circuits to recover coarse, free gold and the copper. The existing leaching circuit continued to operate on the copper flotation tailings with some minor modifications to the solution handling systems. A S02/Air cyanide destruction circuit was also added at that time."

Jan 1, 2000

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' Circular (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date and is being published as a similar series of seven miners' circular pros. 51-57, revised) on accident prevention in metal and nonmetallic mines. These circulars are: Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1957

By E. G. King

Heat of formation values for mercuric sulfide appear in all the comprehensive listings of thermodynamic data, but experimentally determined entropy values have been lacking. Consequently, all free energy calculations involving mercuric sulfide have been based upon estimated entropy values. This paper reports Bureau of Mines measurements of the low-temperature heat capacity of red mercuric sulfide (cinnabar) and the entropy value at 298.15° K. derived therefrom. The entropy value was combined with heat data to obtain free energy values for the formation of red mercuric sulfide from liquid or gaseous mercury and from rhombic or gaseous diatomic sulfur.

Jan 1, 1962

By G. A. Johnson

Basic management principles will be discussed (as they apply to minerals education efforts), especially in light of the changing nature of volunteerism in today’s society. Also, the “minerals education tree” will be presented, along with public opinion / public policy realities.

Jan 1, 2001

By Dale Bartholomae, David Harrison, Edward J. Walter

Methods that involve the use of signature blast holes in order to identify the particular frequency characteristics of a geographical area are widely available. Information acquired can be used to determine optimum blast hole timings to produce the desired constructive and destructive inference. However, these types of analyses can be both complicated and expensive. This study will investigate the use and practicality of signature hole and/or shift and sum analysis software and their application to small diameter construction utility blasting operations in Pennsylvania and faster moving projects in general. A determination will then be made as to whether this technology can be utilized by today’s blaster, from both a functional and a cost effective basis. Single hole blasts will be detonated on various smaller construction projects and will be monitored with an array of seismographs. The collected data will be analyzed in order to determine the optimum timing between holes to produce the preferred frequency content while keeping in mind the explosives user’s current inventory of blasting supplies.

Jan 1, 2005

By Rob Famlield, Gavin Yuill, William Birch

The Blasting Research Group at the University of Leeds, in the United Kingdom, continues to be highly active in the area of the environmental impact of blasting. In recent years a major part of this research has been concerned with the use of linear superposition. This technique relies upon the assumption that all the holes in a blast produce identical vibration signals. Previous work at the University has shown that this assumption is not sufficiently robust to be generally applicable. This is due to a number of factors of which the key variable appears to be dynamic confinement

Jan 1, 2002

By R. E. Thill

The ultrasonic pulse measurement system described measures velocities of longitudinal (compressional) and shear waves in rock to give values that can be used with density values to determine the dynamic elastic constants of rock. A special feature of this pulse measurement system is its unique acoustical bench that minimizes errors in pulse transit times that are commonly associated with coupling, sample alinement, and sample orientation. Some special features of the acoustical bench are its highly versatile transducer cartridges, a pneumatic ram coupling device, an orientation mechanism, and a vacuum chuck sample holder. The lathe-bed-like construction of the acoustical bench assures automatic alinement of samples and versatility in accommodating samples of various shapes and sizes.

Jan 1, 1968

By Richard J. Hartman

Current design practice is to select steel sheet piling sections using sufficient section modulus and yield strength to resist the calculated bending moment. Thus, section modulus is the only property of the sheet pile cross section used in the selection process. Full scale laboratory testing documented that section modulus alone is insufficient to predict the strength of sheet piling. During testing, sheet pile sections with equivalent section modulus exhibited as much as 75 percent difference in load resisting capacity. Analytical study following the testing established that, in addition to the traditional longitudinal (vertical) stress in sheet piling, transverse (horizontal) stresses are also present. Transverse stresses reduce the ability of the sheet piling to function in the intended manner. It was found that transverse stresses result from the pressure applied by soil and water and that the capacity of the sheet piling diminishes with increased pressure. All sheet piling is subject to this behavior. This paper describes the testing and the results and establishes that a problem exists. A two dimensional procedure is described that assists in evaluating transverse stresses and their effect on sheet pile capacity. A method of creating design aids for use by engineers is illustrated.

Jan 1, 2006

By R. B. Anderson

As a part of a Bureau of Mines program on the conversion of coal to liquid and gaseous fuels, the kinetics of the Fischer-Tropsch synthesis on iron catalysts was investigated. Nitrided catalysts were studied at 21.4 atmospheres using feed gases ranging from 2H2+1CO to 0.25H2+1CO, and at 7.8 to 21.4 atmospheres using 1H2+1CO gas. The overall apparent activation energy increased with increasing carbon monoxide content of the feed gas from 19.5 kcal/mole for 2H2+1CO to 23.7 for 0.7H2+1CO. The rate of synthesis with 1H2+1CO feed increased linearly with operating pressure from 7.8 to 21.4 atmospheres. A semifundamental rate equation of the form [r=a'PH2 0.6pco 0.4- ?r0.5PH200.5] was shown to fit the data satisfactorily. The relative usage of hydrogen to carbon monoxide decreased with increasing conversion, passed a minimum, and then increased. Apparently water is the principal primary product and carbon dioxide is produced by subsequent water-gas shift reaction. In another group of experiments water, carbon dioxide, argon, and methane were added to 1H2+1CO feed to a nitrided iron catalyst. Argon and methane were only diluents. Carbon dioxide was a slight inhibitor and water vapor was a strong inhibitor to the rate of synthesis. Water accelerated the water-gas shift and usually increased methane production. Important factors of catalyst geometry in determining rate were found to be particle size and extent of reduction. Apparently the active portion of the catalyst is confined to a layer of 0.01 to 0.02 cm from the external surface of particles. A special solution was made of differential equations relating re¬action at the catalyst surface to diffusion in pores of the catalyst for spherical particles with an active layer surrounding an inert core. The equation derived expressed the experimental data reasonably well. Diffusivities determined by this equation varied from 3 to 24X10-6 cm2/sec; these values are of the same magnitude as observed for the diffusion of gases in liquid. The appendix presents a group of synthesis experiments at pressures of 21.4 to 103 atmospheres. In this range the rate of synthesis on nitrided iron catalysts increased with pressure to the 0.74 to 0.84 power.

Jan 1, 1964

By A M. Purba and A Sjadat, A D. Wilson

Ongoing mining of the East Ertsberg Skarn System orebody below the Gunung Bijih Timur and Intermediate Ore Zone caves has been relatively successful and a ramp up to 80 000 t/d was achieved in the Deep Ore Zone Mine. However, the distribution of production, the overall drawpoint availability as well as the rate of change of the cave back profile has not followed the anticipated path. Several key factors influencing cave growth and progress, grade variation, fragmentation, wet muck and surface subsidence have been recognised over the life-of-mine that now have to be taken into account for planning the later stages of mining.The paper will discuss the influence of geological controls of lithology and structure – how this as well as other contributing aspects have impacted ore flow, contributing to some of the widespread panel damage, and been a key factor in compacted draw columns and caused an accelerated appearance of water ingress. This in turn has rapidly changed the distribution of wet drawpoints requiring remote mucking and special controls that also affect the call from the remaining dry drawpoints. Comment is also made on the potential final cave profile if it continues along the current trend and some discussion is offered about possible mitigation measures if this were to come about.CITATION:Wilson, A D, Purba, A M and Sjadat, A, 2016. Progressing cave performance into the later stages of the Deep Ore Zone mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 285–292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Wilfrid Comeau

The RICHTER scale is used in classifying earthquake severity. It is an energy scale giving the estimated energy liberated at the source of the earthquake. Earthquake damage on the earth’s surface, for example at the epicenter - spot on the earth’s surface directly above the earthquake, for a given RICHTER number can vary. This depends on the depth of the earthquake focus. Deeper earthquakes will generally cause a lower level of damage at the epicenter but the damage will be spread over a greater area. As mentioned by Randy Wheeler on Blastserve, each successive RICHTER number represents about a 30-fold increase in energy. This scale is open at both ends with “0” RICHTER equal to about 104 Joules. The lowest level detected by sensitive instruments is about 2 on the RICHTER scale or about 107 Joules. The highest-level earthquake detected at 8.9 RICHTER represents a release of about 3 x 101 7 Joules.

Jan 1, 2003

By E. H. Burroughs

HISTORICAL REFERENCES OCCURRENCE-GEOLOGY AND ORIGIN. 4. ARNOLD, RALPH. Conservation of the oil and gas resources of the Americas, Econ. Geol., vol. 11, Apr.-May, 1916, pp. 203-222; June, 1916, pp. 299-326; Proc. 2nd Pan American Sci. Cong., 1915-1916, vol. 3, Conservation of natural resources, pp. 207-237. Shows occurrence of oll, and status and possibilities of oil Industry in each country. Discusses briefly ways in which oll reserves may be conserved. 5. RUTIS, A. A. Petroleum known since remote times. Oil and Gas Jour., vol. 15, Nov. 2, 1916, pp. 33, 37. Gives historical reférences to the use of petroleum from Bible times to its discovery In America. See also Nos. 3, 257, 202, 337, 1843.

Jan 1, 1919

Kudremukh Iron Ore Company Ltd, a wholly owned Government of India Enterprise, was established in the year 1976 to develop mine and plant facilities to produce 7.5 Mtpa of high-grade iron ore concentrate at Kudremukh. The mine and plant facilities were commissioned in 1980. In view of high demand for iron oxide pellets in iron and steel industry worldwide and as a diversification activity, a pelletisation plant of 3.0 Mtpa capacity was commissioned in the year 1987 at Mangalore for production of high-quality blast furnace and direct reduction grade pellets for export. The pellet plant capacity has been increased to 3.5 Mtpa by technological improvement which included installation of roll press for quality and productivity improvement. In addition, the pellet capacity is being increased to 4 Mtpa by the addition of Shaft Pelletising Furnace plant.

Jan 1, 1999

By P. Sun

Abstract: From the viewpoint of interaction mechanics of solid and gas, a coupled mathematical model is presented for coal/rock mass deformation and gas leak flow in parallel deformable coal seams. Numerical simulations for the prediction of the safety range of mining of protection layer are performed with experimental data from a mine with potential danger of coal/gas outbursts. Analyses show that the numerical simulation results are consistent with the measured data on the spot. Therefore, the coupled model shows a positive future for applications in a wide range. ZUSAMMENFASSUNG:Von der Veranschaulichung der Abhängigkeit Mechaniker für Körper und Gas, wird ein verbundenes mathematisches Modell für festen coal/rock Deformation und Gasleckstelle Fluß in parallele deformable Kohlenähte dargestellt. Numerische Simulationen für die Vorhersage der Sicherheit Strecke, die Schutzschichtbergbau verwendet, werden mit experimentellen Daten von einer Grube mit möglicher Gefahr der coal/gas Ausbrüche durchgeführt. Analysen zeigen, daß die numerischen Simulation Resultate mit den gemessenen Daten bezüglich des Punktes gleichbleibend sind. Folglich zeigt das verbundene Modell eine positive Zukunft für Anwendungen in einer breiten Strecke. RÉSUMÉ: Du point de vue de la mécanique d'interaction pour le solide et le gaz, un modèle mathématique couplé est présenté pour l'écoulement plein de déformation de coal/rock et de fuite de gaz dans les filons houillers deformable parallèles. Des simulations numériques pour la prévision de la gamme de sûreté employant l'exploitation de couche de protection sont effectuées avec des données expérimentales d'une mine avec le danger potentiel des accès de coal/gas. Les analyses prouvent que les résultats numériques de simulation sont conformés aux données mesurées sur place. Par conséquent, le modèle couplé montre un futur positif pour des applications dans un éventail.

Jan 1, 2003

Develop tools that mine personnel can use to comply with 30 CFR,Part 47. Background The new MSHA rule, 30 CFR, Part 47 (also known as the HazCom rule), requires all mines to develop a written program to track hazardous chemicals at their sites. More specifically, the rule requires that mines list all chemicals and determine which are hazardous; develop a written Hazard Communication Program; label all containers used to store hazardous chemicals; obtain or develop Material Safety Data Sheets (MSDS) for all chemicals stored or produced; provide miners with training in working around hazardous chemicals; and make information about hazardous chemicals available to all workers. All mines with six or more employees must have complied with the new rule by September 23, 2002, and mines with five or fewer employees will have to be in compliance by March 21, 2003.

Mar 1, 2003

This paper is not available for inclusion in the Proceedings at the time of printing, but it will be included as an insert.

Jan 1, 1984

By T. Majcherczyk

Shaft lining reinforcing analysis of two shafts under construction has been presented in this study. The first shaft was driven from the surface, while the second was deepened. Mining and geological conditions have been studied with respect to the lining capacity. The improvement of shaft stability comprised two elements, i.e. reinforcement of the shaft lining capacity and improvement of the strength properties of the rock mass. In both tested cases, the particular hazard was connected with non uniform loadings of the lining, which could generate shearing stresses within lining structure. Thus such elements as armored concrete with high strength properties, bolting and injection sealing of the rock mass, and the use of special ring reinforcing the shaft lining have been used in order to reinforce the shaft-rock mass system. Practical conclusions related with new technological solutions, allowing the rock mass and shaft lining reinforcement, have been included for the present study. Practical conclusions related with new technological solutions, allowing for rock mass and shaft lining reinforcement, have been also included to the present study.

Aug 1, 2013