Search Documents

By Luis Angel De Montreuil

Ante el problema del tratamiento de minerales complejos, la demanda de eficiencia metalúrgica y bajos costos de operación, el ingeniero busca el apoyo de la mineragrafía como estudio microscópico de los minerales económicos. En ese sentido, el presente texto señala la importancia de la minegrafía -en tanto ayuda a la flotación de los sulfuros valiosos de los yacimientos peruanos. Asimismo determina las propiedades de los minerales con el fin de identificarlos.

Jan 1, 1986

By E Apaza, R Neumayr

This paper aims to summarise the discovery of the QTS Central resource, a previously unidentified +1 Mt inferred resource that lies between two major CSA resource systems.The 1.7 Mt at 5.76 per cent Cu, QTS Central ore system represents 1/6th of the CSA mineral resource and was discovered in 2014 based on the accumulation of historic exploration records dating back to 1989.The CSA deposit consists of five ore systems hosted within turbidite-derived siltstones (CSA Siltstone) and lesser sandstones (five per cent) of the Devonian Amphitheatre Group. The host sediments strike approximately north–south with a steep westerly dip and exhibit a well-developed east dipping cleavage. Most CSA mineralisation is hosted within dilation zones at the intersection of cross-cutting structures and is interpreted as epigenetic in origin.Alteration and weak mineralisation, up plunge to the reported QTS Central mineral resource, was initially detected in 1990 during a downhole electromagnetic conductivity (EM) study, where one hole indicated an off-hole conductor, later tested with four diamond holes. One of these diamond holes intersected 3 m at 7.5 per cent Cu at 200 m. Development of the 9070 Subway drive in 2005/2006, linked the QTS North and QTS South workings and intersected structures interpreted to host QTS Central mineralisation. Subsequent drilling proximal to the 9070 Subway in 2007 identified an up plunge extension to the QTS Central zone (UDD07152: 1.8 m at 6.3 per cent Cu from 10.7 m). Work on QTS Central was largely forgotten until 2012 when the mining of a 450 m infrastructure drive provided a platform to test the anomalous grades. In December 2013, drill hole UDD13055A intersected 20.9 m at 7.2 per cent Cu from 378 m. By the end of 2014, the QTS Central inferred resource was 1.0 Mt at 6 per cent Cu and 18 g/t Ag (Hosken and Apaza, 2014). Late in 2016, further infill drilling occurred from two fronts to increase confidence in the QTS Central resource. The results of this drilling are expected late in 2017.The current interpretation indicates the QTS Central system consists of two main lenses hosted within closely bedded sandstones and siltstones. The sandstone in general is not mineralised, being heavily silicified, while the siltstone is mineralised and chloritised. The main mineralised lens is 75–200 m along strike and 450 m high. Massive sulfide feeder structures lie at the core of the two main lenses, although the characteristics of the QTS Central system tend toward the mineralisation being more chlorite-rich than in QTS North and QTS South.CITATION:Apaza, E and Neumayr, R, 2017. The discovery of the QTS Central ore system, CSA mine, Cobar, NSW, Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 151–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

The President was authorized to appoint. a liaison committee to cooperate with the American Mining Congress in respect to the establishment of a Secretary of Mines and Mining in the President's Cabinet. He appointed Edwin Ludlow, Chairman; Mark L. Requa, and J. E. Johnson, Jr. It was resolved to accept the invitation from the Chicago Section to hold the. 120th meeting of the Institute in Chicago during the week of Sept. 15, 1919. The action of the Executive Committee in appointing Past President E. Gybbon Spilsbury as representative of this Institute to visit France upon the invitation of the Société des Ingénieurs Civils de France was approved. The final budget for 1918 was approved. Tile President was authorized to appoint a committee, of three members, on the Development of Activities of the Institute. The committee was requested to report at the February meeting of the Institute, and the Secretary was requested to invite each local section to have a member present to discuss the subject. The President appointed J. W. Richards, Chairman; P. N. Moore, and Allen H. Rogers. Thirty-six members, ten associates, and five junior associates were elected; one change of status from associate to member was granted; two members were reinstated; and eight resignations were accepted. An extension of time was granted to nine members. The dues of eight members were suspended on account of their being in active service.

Jan 2, 1919

By J. W. Jensen

EXTENSIVE research and development was performed on the manganese-copper vibration-damping alloys to determine the relationship between the properties of the alloys and variations in composition, fabrication, Mid heat treatment. Mn-Cu alloys with unusually high specific damping capacity, 20 to 25 percent at a stress of 5,000 psi, have also the following useful properties: Tensile strength, 90,000 to 110,000 psi; yield strong, 60,000 to psi; elongation, 20 to 25 percent; hardness, 90 Rockwell B; and fatigue limit at, 28,000 to 30,000 psi. Both standard and special methods of testing were employed to obtain data on strength, modulus, hardness, resistivity, dilatation, micro-structure, crystal lattice, and damping capacity. The extensive tabular and graphical data on these properties are presented for alloys containing 50 to 85 percent as quenched d solution) and after various aging treatments. Expansion coefficients for all Mn-Cu solid solutions are graphed and a dilatometer study of contraction during aging is reported. Although high damping capacity is associated with aging to precipitate a-Mn from solid solution, with a cubic-tetragonal transformation and with the occurrence of antiferromagnetic ordering in Mn-Cu alloys, a tenable theory of the damping mechanism has not been reached.

Jan 1, 1965

By Thomas Prietl

The use of gas stirring systems through the furnace bottom is common for anode and holding furnaces in the copper industry The first implementation of a gas stirring COP KIN® system in a Peirce-Smith converter was performed at the New Boliden smelter, Rönnskar, Sweden. In addition to other benefits, a decrease in process time and a decrease of the oxygen content in the blister copper were observed. To determine the effects of the gas stirring system and the process endpoint, an optical production control ?Semtech OPC system? was used. The light emission of the converter flame as an optical process parameter provides qualitative on-line process information, and is also used for endpoint determination of the slag making process, on-line control of iron content in white metal, quality control of slag etc. The results, benefits and risks of using the COP KIN® and OPC system for a Peirce-Smith converter are reported.

Jan 1, 2005

By Paul R. Smith

The Colorado School of Mines Research Institute (CSMRI) was founded in 1949 to fill mining industry and government needs for minerals research and development. The operations of scores of mines, mills, and plants around the world are based on the results of work done by the Research Institute. Among other things, the Research Institute conducts studies in geology, mine planning, mineralogy, size reduction, minerals processing, and hydrometallurgical techniques in extractive metallurgy. Many CSMRI projects also involve energy and environmental considerations. What follows is a summary of some of the studies in which the Research Institute has been and is currently involved, as well as some comments on trends and developments in the industry.

Jan 2, 1982

By Burcu Ertug, Necip Ünlü

"On average, one out of two glass bottles coming on to the market is provided by recycling processes in Europe. Glass recycling has been started by the early of 1970s in Turkey, and the recycling amount has been reached to 70 thousand tons recently, while 4.2 million tons which represents only 25 percent of total glass manufactured, is the amount of glass collected annually for recycling in the world. The glass recycle process basically involves collecting, sorting, then crushing and grinding after which glass cullet is produced as the secondary raw material. Removing of the contaminants from the glass cullet, and then melting are the next steps. In this study, recent developments of 100% recyclable without any deterioration in quality, and never decomposable glass, are discussed detailed in terms of glass production processes.1.IntroductionIn many countries, waste glass constitutes a large proportion of solid wastes, and recycling the glass is a major environmental problem all over the world [1]. Among the diverse types of waste, glass is one of the most valuable recycling materials because it can be revived and recycled completely and hardly decomposes [2]. Between 80% and 85% of the mass output from the worldwide glass industry is either in the form of containers for the food, beverage, and pharmaceutical industries, or flat glass for building construction or for motor vehicle manufacture. Other product segments, whilst only constituting about 15% of the mass output, produce high value technical and consumer products by comparison with container and flat glass [3].In the present study, the recycling of Liquid Crystal Display (LCD), Cathode Ray Tubes (CRT) and Printed Circuit Boards (PCB) were examined. The production of glasses and glass-ceramics from glass cullet, synthesis of different compounds from recycled glass were other subjects of interest. The use of recycled glass for construction industry and using glass as aggregate were emphasized. Finally the recovery of glass fibers were investigated."

Jan 1, 2012

By Alok Garg, Rajeev Kumar Dayal

The Himalayan ranges have complex geological formation induced with locked up tectonic stresses and squeezing ground conditions. High overburden, steep slopes, perennial snow, and forest cover restricts accurate prediction of geological features, resulting in surprises during excavation. The tunnel planning under high altitude, extreme climatic, and unfavorable approachability conditions requires elaborate detailing. The construction technique and working faces for excavation are influenced by site accessibility/high overburden conditions, restricting the provision of access tunnel or shaft. The paper discusses site constraints influencing construction method and working faces for 8.9 km long highway tunnel at elevation 3,000 m under 1,900 mover burden through quartz-mica-schist formation.

Jan 1, 2001

A summary of the more important work by previous workers is followed by brief descriptions of the rock formations and regional structure. Type examples of the various forms of mineralization are described and the conclusion is drawn that there has been one main period of ore formation, namely, during the "Viti Revolution" in the mid or late Miocene.INTRODUCTIONThe Crown Colony of Fiji is comprised of a group of some 250 islands situated between latitude 160 sand 21 0 S and longitudes 1770 E and 1780 w: By far the greater, part of the total area, 7,083 sq. miles, is contained within the two main islands, Viti Levu 4,053 sq. miles, and Vanua Levu 2,128 sq. miles, and it is to these that most geologists have directed their studies. The most detailed work has been in the Tavua Basin, north coast of Viti Levu, centering about the mining town of Vatukoula and the geology of this area forms the subject of a separate paper by Blatchford (this volume p. 13).The present contribution summarizes geological knowledge of Fiji, at the time of writing (Feb. 1952), with particular reference to the known mineralIzation, but excluding the Tavua Basin. For general descriptions of Fiji's topography reference should be made to the recent works of Derrick and Dunkin.PREVIOUS WORKERSPeriod 1840-1930Prior to the gold rush of the early 1930s the visiting geologists concerned themselves in the main with the struc...

Jan 1, 1953

By Frank C. Townsend

Waste disposal schemes using spent shale in embankments require a thorough knowledge of its geotechnical engineering properties for environ-mentally safe disposal. In this context, the objective of this laboratory investigation was to determine the physical properties, geotechnical properties, and composition of spent oil shale retorted by the PARAHO and TOSCO processes. Physical properties consisted of mechanical analyses, Atterberg limits, and specific gravity determinations. Geotechnical engineering properties were determined by compaction, maximum-minimum density, unconfined compression, triaxial compression, permeability, direct shear, Ko, cyclic tri-axial, resonant column, and Los Angeles Abrasion tests. Petrographic, chemical, and scanning electron microscopy analyses were used to determine compositional features. Unprocessed shale is hard and durable and more properly described as a carbonate rock instead of shale. PARAHO is classified as a GP, while TOSCO classifies as an SM. PARAHO requires no moisture for compaction to maximum densities; however, TOSCO does. Retorting causes a loss in durability but creates self-cementing characteristics, which for PARAHO a 3-to 8-fold strength increase was observed, while for TOSCO the increase was 1.5 to 3 folds. The shear strength, compressibility, and dynamic properties of compacted PARAHO are comparable to those for sandy gravels. Compacted PARAHO is semipervious, while compacted TOSCO can be semipervious to impermeable.

Jan 1, 1979

By Pietro Navarra

A great deal of effort has been expended on how to optimize conventional water cooling circuits in furnace cooling elements, and the results have been largely satisfactory. However, there is a general agreement that the proximity of high-pressure water passages to the flow of molten furnace products is a safety concern. Nonetheless there exists little alternative to the formula: increasing furnace integrity implies the incorporation of more extensive forced-convection water cooling systems. Recent developments in evaporative cooling technology have resulted in the development of a high-capacity heat pipe capable of operating under the thermally intense environments of a metallurgical furnace. The system functions using several kg of a working fluid (water) in total, has no moving parts, and allows for a significant reduction in cooling water requirements. Full-scale pilot tests of a copper tap hole and slag launder were done in 2003 and2005, with detailed results given in this paper.

Jan 1, 2006

By Orr C. W

In previous papers (1, 2), the influence on the creep resistance of elements normally found in commercial lead has been recorded. The results in the present paper refer to the influence of calcium, an element which is not found naturally in lead, but which has been used commercially in the form of alloys. It was realised that calcium would act as a deoxidising agent for lead-and in fact it was with this feature in view that both calcium and magnesium were used as additions. Subsequent work (including the results given in the present paper) has tended to diminish the importance which at first seemed to be associated with the presence of oxygen in lead. The structure of the dilute calcium lead alloys has been worked out in detail (S) and the phase diagram shows the existence of limited solid solubility and a compound CaPbs.

Jan 1, 1938

By Li Keqiang

This paper discusses the pile foundation of tall buildings in Shenzhen region. For 156 constructed tall buildings exceeding 18 storeys, about 86. 5 per cent of the sum. The two main types of foundation used are the semi?machine?bored/slurry drilled cast?in?situ pile and the excavation pile (hand ?dug caisson). The engineering geologiical condition in Shenzhen was analysed. In general, the bed rock level is not too deep. It belongs to hard rock, but the geologic structure is more complex and the tectonic fissures is plenty. According to experiences of the researches, tests, designs and constructions of pile foundation, we present the basic design principle of pile foundations for tall buildings as follows; (1) pile strength control to select the pile type and to choice the cross sectional dimen­sions, must be in compliance with the strength of the pile. (2) bearing stratum strongly weathered, moderartely weathered and slightly weathered rock may be used as the bearing stratum. (3) bearing pile bored /drilled cast-in-situ pile designed as an end bearing pile. (4) friction pile precast concrete pile, prestressed concrete tubular pile and driven cast-in-situ pile designe as a friction pile. In case, pile design is in compliance with these principles, it may be safe, economical and reasonable.

Jan 1, 1991

By H. W. Sohns

A retort was constructed in which fine particles of shale, entrained in steam or other gaseous media, could be retorted at controlled temperatures and residence times and the effects of retorting variables upon quality and quantity of products could be determined. Studies of the effects of temperature upon products obtained from Green River (Piceance Creek Basin, Colo.) and Chattanooga (Tenn.) oil shales were completed. The feasibility of using the retort to process a shale of extremely high moisture content from Brazil also was investigated. Air was used as the entraining medium in a series of studies in which combustion of some of the products of retorting within the retort tube supplied a major portion of the process heat. In another series, shale oil from a conventional retort was cracked thermally to obtain data for comparison with results of retorting en-trained shale. In still another series the effects of rates of steam flow and solids feed upon rates of heat transfer from the furnace to the process stream were studied. Crushed quartz rather than oil shale was charged to the retort in this series. A study was begun in which raw shale was partly retorted, the products separated, and the partially retorted shale recharged to the retort. The shale was to have been recycled until it was completely retorted in an effort to improve oil yield by recycle retorting; however, the project was terminated before the investigation was completed.

Jan 1, 1959

By G Smart, D Ward, J Grace

Ridgeway Gold Mine is part of Cadia Valley Operations which is wholly owned and managed by Newcrest Mining Limited. It is an underground sublevel cave (SLC) operation mining approximately 5 Mt per annum. Ore control systems at Ridgeway have been designed to deliver gold and copper metal production through focussing on the ore characteristics that impact on mine and mill performance and ultimately metal delivery. This is achieved using data collection and management systems which allow data to be collected digitally with æat captureÆ validation routines. These data form the basis for forecasting and on-going systems analysis which aim to accurately assess local in situ and drawn ore characteristics. Physical attributes of ore such as draw characteristics, brow conditions, visual grade estimates and draw point sampling are routinely recorded. Ore tracking and accounting systems monitor gold and copper grades, copper mineralogy, host lithology and ore sizing. These factors have material impacts on concentrator throughput and metal recovery. Draw point recovered grades are routinely reconciled back to design data to monitor and assess draw performance. Statistical variance controls are also employed to analyse mine and plant performance and guide actions.

Jan 1, 2003

By R. A. V. Raff

Although falls of roof, face and rib (or side) of coal mines were the third ranking cause of disabling accidents in 1966, the accidents from these falls resulted in the most serious injuries and accounted for approximately 50 percent of the total fatalities (I). Further breakdown of these statistics shows that 88 percent of the fatal accidents occurred within 100 feet of the working face and that 96 percent of the deaths were in bituminous mines, with only four percent taking place in anthracite workings. These figures demonstrated the need for improved reinforcement procedures in operational coal mines, and they provided ample justification for research in the area of accident prevention. The purpose of this project was to investigate the use of polymers and of related techniques to achieve rock bonding and reinforcement of coal mine structures, in order to obtain better or permanent ground support (e.g., drifts, entrees, coal and ore passes, galleries, tunnels and shafts) by the fill ing of fissures in the rock, thereby preventing or delaying the onset of serious rock degradation processes.

Jan 1, 1973

By K. Terhaar, K. Prisbrey

The objective was to determine operating protocols for a lead and silver column flotation cleaner, being considered for installation at Sunshine Mining & Refining Co.’s Kellogg mill in Northern Idaho. In this column, tetrahedrite and galena were floated, and pyrite and other gangue minerals, including siderite and silica, were depressed. The procedure was to develop a dynamic simulation using a linear transfer function approach. The transfer function related cause and effect variables such as the influence of collector and depressant dosages on recovery and grades. Bench-scale flotation tests followed by pilot column testing provided the data used to develop a linear transfer function. The transfer function was derived using a spreadsheet. This model was applied to simulate how the flotation column could be made to respond to disturbances in feedgrade. The results were that xanthate, zinc sulfate, and sodium cyanide were found to be suitable controls for grade and recovery. Simulations showed the best sequence of manipulations of these reagents, and these sequences were useful for future operator training. The conclusion was that linear transfer functions were able to simulate lead and silver recovery, develop scenarios for operator training, and provide a foundation for future on-line control.

Jan 1, 1999

By H. B. Jensen

STUDY of the thermal-solution process was begun by treating crushed oil shale in a small autoclave at temperatures of 700° to 950° F. The effect of temperature, reaction time, type of solvent, and richness of shale upon the amount of organic matter that was removed from the oil shale was thus determined. Following this orientation work a semicontinuous, bench-scale apparatus was built so that heated solvent could be pumped through a bed of shale under elevated pressure, thus removing the converted organic matter from the spent shale. After some operating experience had been gained, a continuous unit was constructed. This permitted treating a slurry of shale oil and pulverized oil shale at about 300 p. s. i. and temperatures of 750° to 850° F. for various retention times. Considerable cracking and polymerization of the shale oil were found to take place during the process. In an attempt to prevent this, a study was made of extraction of the shale in batch-type autoclaves under high partial pressures of hydrogen at total gas pressures of as much as 4,300 p. s. i. at 850° F. The thermal-solution process was found to convert over 90 percent of the organic matter in oil shale to oil and gas. The highest yields of gas and oil obtained without hydrogen pressure were equivalent to 119 weight-percent of those obtained from the same shale by Fischer assay. With a high partial pressure of hydrogen, yields equivalent to 126 weight-percent of Fischer assay were obtained. However, the oil produced by thermal solution has a higher boiling range than that obtained by other retorting methods, particularly so if the thermal-solution process is used without a high partial pressure of hydrogen. Nondistillable oil (all benzene-soluble material that would not distill under 2 mm. Hg absolute pressure without cracking) equivalent to over 100 percent of the organic matter in the shale was obtained without hydrogen pressure in the system. When the process was carried out under hydrogen pressure, the yield of nondistillable oil amounted to 60 to 70 weight-percent of the organic matter. Part of this heavy material is formed partly by polymerization and condensation of the shale-oil solvent used. These reactions, as well as cracking of the solvent to form gas and a carbonaceous deposit on the shale, are unfavorable features of the process.

Jan 1, 1953

Optimizing production scheduling in open pit mines is important for managing cash flows of mining operations. This paper describes a new, probabilistic, mixed integer programming (MIP) formulation which has been developed to minimize the risk of not achieving planned production targets, in terms of metal production and ore tonnage feed for the mill during production, while considering maximization of total discounted economic value. The new MIP model also recognizes that to minimize movement of excavators over long distances and accommodate equipment access, the blocks scheduled for mining within a period cannot be spread too widely. The model is applied to a laterite nickel-cobalt deposit, as an example of multi-element deposits that have complex ore quality constraints. The results show that the proposed model generates feasible schedules. When compared with traditional optimization techniques, the new model is superior in terms of minimizing the risk of not meeting production targets, especially at the early stages of production, and in terms of generating practical scheduling patterns.

Jan 1, 2006