Search Documents

By Michael Lenz

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels. The predictive program was initiated on the P&H Model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Feb 24, 1997

By Alan J. Lutenegger

Some years ago, a method was developed to incorporate a grout column around square-shaft helical screw-piles and anchors to increase shaft buckling resistance under compression loading. An additional benefit of this grouted shaft is to increase the load capacity in both compression and tension, depending on the geometry of the lead helical section and the soil conditions. Because of the unique construction procedure, the contribution of the shaft to the total capacity has largely been unknown. The behavior of grouted shaft helical anchors in clay was investigated by performing full-scale axial uplift (tension) load tests on a series of anchors installed at the University of Massachusetts Geotechnical Test Site. In order to isolate the contribution of the grouted shaft to the total load capacity, anchors were installed with a wooden dowel connection between the lead helical section and extension sections on three of the four anchors so that only the shaft resistance would be measured during the load tests. The grouted shafts ranged in length from 10 to 30 ft (3 to 9 m). Initial tests were performed approximately 5½ months after installation. Nearly four years after the initial tests were performed, the tests were repeated to evaluate any significant change in capacity with time and/or repeat testing (preshearing). The soil conditions at the site are presented along with the load-displacement curves for both the initial and repeat teats and a discussion of the analysis of the results. Repeat load tests showed an increase in capacity from the initial testing, however the percent increase was not the same for all depths. The results demonstrate that considerable shaft resistance can be developed in clays from the grouted shafts as might be expected. Depending on the L/D ratio of the shaft and the contribution of the lead helical section, at working loads the shaft capacity can dominate the behavior.

Jan 1, 2011

By Balakrishnan Nanthakumar, Marek Pawlik, Dennis Grimm

"The anionic flotation of a high-iron phosphate ore from Agrium - Kapuskasing Phosphate Operations was investigated through batch flotation tests in the presence of soda ash. The flotation data were supplemented by titration of the flotation pulp with soda ash, analysis of process water chemistry, and determination of the mineralogical composition of the ore. The results of lab tests were applied to the flotation circuit design allowing the flotation plant to efficiently process problematic ores. Process control measures (pH, conductivity) were also developed.Calcium cations and sulfate anions were identified as the dominant ions present in the process water when the difficult-to-process ores are beneficiated in the flotation plant. The concentrations of calcium and sulfate ions were consistent with the presence of a small amount of a calcium sulfate mineral in the ore although an oxidation/weathering process of iron sulfide minerals present in the ore could also be responsible for the observed water chemistry and subsequent flotation problems with the ores. The latter possibility suggests that the long-term stockpiling of such ores may have a highly negative impact on the flotation process.The role of soda ash in the flotation circuit is to precipitate metal cations from the pulp thus allowing the tall oil-based collector to selectively interact with the phosphate components.INTRODUCTIONPhosphorus minerals are the main source of this element for the production of fertilizers, and the froth flotation process is the most important technology for beneficiating phosphate ores. The flotation concentrate from Agrium-Kapuskasing Phosphate Operations (KPO) is transported to Redwater Fertilizer Operations in Alberta (also operated by Agrium) where the phosphate concentrate is converted into a phosphate fertilizer and other important chemical products. The KPO phosphate ores differ widely in mineralogy and phosphate grades, and are broadly divided on-site into three classes. The easy-to-float A-type ores do not pose any major flotation problems, but the B-type and “marginal” ores, which are quite common in the KPO igneous phosphate deposit, are not always readily-floatable using the current reagent suites and process parameters (pulp density, feed particle size, pH). In fact, marginal ores are presently considered impossible to process by flotation. A-type ores contain normally more than 15% P2O5 and less than 8% ferric oxide equivalent (Fe2O3). B-type ores are approximately of the same P2O5 grades as A-type ores but their iron content may reach 30% Fe2O3. Any material containing less than 15% P2O5 is rejected as waste rock."

Jan 1, 2008

By W. H. Zieman

"THIS IS THE THIRD of the consecutive Annual Forums on Grinding that were instituted by Mr. L. E. Djingheuzian in 1957. The first was on the subject of Ball Milling (Transactions, Volume LX, 1957) and the second on The N on-Cataracting Ball Mill (Trans-actions, Volume LXI, 1958). From the discussions at these forums it was evident that one of the most important factors affecting the efficiency of grinding is the shape of the liners. In order to make a study of liners in use, it was •decided to seek the co-operation of operators across the country by sending out questionnaires requesting basic information. Additionally, these operators were urged to set down briefly any pertinent information on the subject acquired through experience and experiments at their own particular plants. A compilation and analysis of these data were to form a basis for discussion at the Forum on Liners at the Annual Meeting in Montreal, April, 1959. The response of the milling fraternity to this solicitation was most gratifying, and clearly indicated the importance attached by the operators to the effect of liner design upon overall grinding performance."

Jan 1, 1959

By Christoph Mueller

Mining operations are characterized by cost pressure and cycling product prices. A high potential for enhancing efficiency is the integration of all single steps of the mining working chain into a production process structure to make advantage of an optimized flow of material and information through the ?moving ore factory?. As modern mining machinery today is controlled electronically and even already operated autonomously, a smooth and cost efficient flow of data in the mining process will be crucial for cost efficient future mine operations. Therefor, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ?common electronic language? for easy and standardized data exchange between mining machines and central computer systems. As in other industries, this standard is expected to have significant impact on the use of automated equipment. It shall provide easy ways of using multi vendor machine installations in data controlled mining processes. At the same time it reduces cost for individual development of interfaces for all parties involved. Standardized data exchange is also a crucial precondition to integrate the mining process into enterprise level modeling, cost analysis and decision finding systems. The standard?s technical architecture is open and flexible for future applications. It uses modern XML technology enabling easy data exchange with commercial databases as well as open on line networking. The IREDES work is carried out by the initiative members working jointly together in the technical work groups. Prototyping implementations of the Drill rigs profile are currently going on. Further profiles under development cover LHD?s/Loaders/Trucks and Explosives Chargers. The first official release covering the Drill Rigs profile is planned for the end of 2002.

May 1, 2002

By Glenn K. Nolan

"Today, more than any other time in recent history, aboriginal communities are looking for ways to be understood as more resource development companies continue to explore and develop Canada's vast resource potential.Recent Supreme Court rulings have affirmed the need to engage aboriginal communities early on in resource development projects. There are many conflicting ideas on how, who, and when to engage. Given the large number of communities and varied cultures, each resource development company must equip itself with a better understanding of the people they are planning to work with.The lecture will begin with a basic historical perspective on treaties and the various societies across Canada. We will also explore the current situation many communities find themselves in today. Building a meaningful relationship with a community is the foundation for a lasting partnership. Every community is unique and every approach to engage communities must be just as unique. The lecture will outline some basic steps that can lead to a better relationship building process between the communities and companies."

Jan 1, 2008

By A. C. Fieldner, S. H. Katz

"Introduction.Recent experiments (Fieldner, A.C., Katz, S.H., Kinney, S.P., and Longfellow, E.S., Poisonous gas from carbon tetrachloride fire extinguishers, Jour. Franklin Institute, October, 1920, pp. 543-565), by the Bureau of Mines have shown that carbon tetrachloride extinguisher liquids when applied to fires produce small quantities of irritating and poisonous gases which may be dangerous in very closely confined spaces where conditions are such that the user can not escape without breathing the fumes. The results of the experiments have been confirmed in an independent investigation by the Underwriters Laboratories (Nuckalls, A.H., Corrosive action and products formed when carbon tetrachloride extinguisher liquids are applied to fires, Nat. Fire Protection Assoc. Quarterly, vol. 14, January, 1921, pp. 221-236) who conducted similar experiments for the purpose of determining the corrosive action of these fumes on metals. Both investigations showed that carbon tetrachloride vapor, hydrochloric acid gas, and phosgene were produced in addition to the ordinary products of combustion, such as smoke, carbon monoxide and carbon dioxide. The Bureau of Mines' tests were made by applying a one-quart extinguisher to a wood fire of excelsior in a gas-tight room of 1000 cubic foot capacity. The glass and metal construction of this chamber limited the experimental fire to very small dimensions. It was, therefore, deemed desirable to make a test on a larger scale in the entry of the Bureau's experimental mine in order to similate more nearly the practical use of carbon tetrachloride and other types of extinguishers in mines.Description of extinguishers.Two series of tests were made under identical conditions on different days. Commercial carbon tetrachloride extinguishers were used in the first series of tests and ""foamite firefoam"" extinguishers in the second series of tests."

Jun 1, 1921

By Peter J. Nicholson

"IntroductionDuring my more than 40 years in the practice of underground construction and engineering, the industry has seen progress from the dig down to rock or hardpan or alternatively drive concrete or steel into the ground and count the blows; then you can be sure of you have a solid foundation; to the modern day, I’m willing to try anything to save money. Of course these are both exaggerations, but not gross ones. After getting bored being supervision on jobs counting blows, I struck out into the new field of “tie-backs” as they were called in the United States, or “ground anchors” as they were then termed in the United Kingdom. After installing some of the first permanent ground anchors for the Corps of Engineers on Lake Michigan as well as the highest loaded rock anchors of the time at two dams on the Ohio River, we were at the top of our game in the 1970’s. Subsequently in the 1980’s when my view of the future of ground anchors saw their installation becoming a commodity item, we branched out into “Pin Piles” now known as Micro Piles, high capacity, steel tube encased, small diameter (5-12” or so), high capacity (100-500 tons) piling. Next came soil nailing, both temporary and permanent retaining walls, as at Cumberland Gap Kentucky. My next morph was into “Cement Deep Soil Mixing” earlier on, known simply as “soil mixing”. For this education I traveled to Japan several times and established a long-term, Joint Venture, relationship with one of the better known Japanese specialty ground modification companies. In Boston at the “Big Dig” we established the then record size soil mixing project, 500,000 or so cubic meters of CDSM concluding in the year 2000. Since then I’ve been involved as a consultant mainly for dams and levees. Below is the story of how I came to be at this place in the road to innovation in Geotechnical processes."

Jan 1, 2017

By J. W. Thompson

SALE AND CONVEYANCE. DEED BY INDIAN ALLOTTEE OF UNSOUND MIND-BONA FIDE PURCHASER. The deed of an Indian allottee whose mind was unsound, but who was not entirely without understanding, is voidable if made before the grantor's incapacity has been judicially determined; and a purchaser of the original grantee who interposes the defense of a bona fide purchaser has the burden of showing a purchase for value and on failure to do so can not claim the benefit of a bona fide purchaser. Adams Oil & Gas Co. v. Hudson (Oklahoma), 155 Pacific, 220, February. 1916. PURCHASER OF MINING CLAIM-RIGHT TO FIXTURES. The purchaser of a mine equipped with an electric hoist, placed in the mine under a rental contract with the owner of the hoist and under an agreement to return it to the owner at the expiration of the term of hiring, can not claim and hold the hoist as against the owner where the agent of the seller explained to the purchaser that the hoist was not owned by the owner of the claim. Montana Electric Co. v. Northern Valley Mining Co. (Montana), 153 Pacific, 1017. p, 1018, October, 1915. AUTHORITY OF GRANTEE TO EXTEND LEASE. A deed conveying lands subject to an oil and gas lease under which the lessee had the right to drill or pay money in lieu of drilling at his option, and reserving to the grantor a share of the royalties under such lease, and expressly authorizing the grantee to lease the land for oil and gas purposes and to take the rentals, authorizes the grantee to extend the existing lease before the expiration thereof in consideration of the annual payment of money in lieu of drilling, as contemplated by the lease.

Jan 1, 1916

By John C. Taylor

A resource document, prepared for the Royal Commission on the Health and Safety of Workers in Mines, which outlines aspects of occupational health and safety in the Canadian metallurgical industry has been expanded to provide examples of some practical solutions. General process descriptions are provided in conjunction with some of the major potential hazards associated with each step. Emissions to the working environment, particularly around converters, are discussed. Newer metallurgical processes, the role of automation and other advances in the metallurgical industry are described with respect to their impact on the work place. The role of staff and unit employees in providing safe working conditions in the complex metallurgical plant of today is outlined and the need for close cooperation within the human sector emphasized. The technology is available and is being applied to integrate the complex process requirements with realistic regulations to control emissions and provide a safe, healthy environment in metallurgical plants.

Jan 1, 1978

By Caroline Gomes de Oliveira

A busca por materiais que atendam as demandas ambientais que vem surgindo com o passar dos anos abre um importante mercado para a aplicação de fibras naturais. Além de biodegradáveis e provenientes de fontes renováveis, as fibras naturais possibilitam a produção de materiais compósitos de baixa densidade e com boas propriedades mecânicas. Para aumentar ainda mais essas propriedades, estuda-se o uso de tecidos de fibra natural em vez das fibras alinhas. As principais vantagens desta nova configuração são o reforço em mais de uma direção ao mesmo tempo e o fato de serem mais compactos, viabilizando a incorporação de uma fração maior de material de reforço. O presente trabalho investigou a resistência ao impacto de compósitos de matriz poliéster reforçados com tecido puro de rami, que é uma das fibras lignocellusosicas mais resistentes encontradas até hoje. Os corpos de prova foram reforçados com 1, 2 e 3 camadas de tecido e foram ensaiados num pêndulo de impacto Izod. Concluiu-se com base nos resultados que o aumento da fração volumétrica de tecido aumenta a resistência ao impacto dos compósitos.

Aug 17, 2017

By Rob Thomas

Main gate roof control during longwall retreat is subject to a significant increase in horizontal stress and risk. The implementation and management of an appropriate roof support design is as a result, an imperative requirement for any longwall mine and must in addition to the likely consequences of a roof fall, also consider the variables of the geotechnical environment, associated support costs and practicalities. This paper will therefore summarise a number of recent advances in main gate roof control in the Australian coal industry. Points considered include; (i) the ?Longwall Acceleration? concept, (ii) macro-scale horizontal stress notching, (iii) micro-scale horizontal stress notching, (iv) bedded versus laminated roof types and (v) the type of cable reinforcement used.

Jan 1, 2006

By M. M. Fine

A process for simultaneously reducing and indurating iron are pellets was developed by Bureau of Mines laboratory research and confirmed on a continuous pilot plant basis. Moist iron are concentrate was balled, mixed with solid reductant, and heated at about 1,100° to 1,150° C. On a small scale, a variety of concentrates and fuels were utilized successfully. The pilot rotary kiln tests were limited to natural magnetite, synthetic magnetite, lignite, and anthracite. In both cases, partially reduced pellets with excellent physical properties were regularly produced with average analyses of at least 80 percent total iron and 60 percent or more metallic iron. These and other prereduced pellets were smelted in the Bureau's experimental blast furnace facility, Bruceton, Pa. With prereduced spheres comprising 85 percent of the burden, the coke rate was approximately half that with standard oxide pellets and production of hot metal was increased by 75 percent. Economic appraisal of the cost of making hot metal indicates that reduced pellets could be more profitable than any other iron raw material in both investment capital and daily cost of operation.

Jan 1, 1970

By Michael Alber

Resin grouted rock bolts are the major support measure in coal mining. They are rather easy and foolproof to install, take immediately load and are the least time consuming support measure for controlling gateroad deformation. The use of only resin grouted bolts allows fast gateroad development which is essential for economical resource exploitation. The design of reinforcement / support systems for coal mining typically bases on empirical methods, which work fine when encountering known or usual ground conditions. However, coal mining approaches depths where little experience exists and numerical modeling is often the only method to estimate ground behavior. This paper discusses the geotechnical properties relevant to numerical model and focuses particularly on input values for modeling resin grouted rock bolts for safe gate design.

Jan 1, 2006

By W. F. M. GOSS

The locomotives in service on the railroads of this country consume more than one-fifth of the total coal production of the United States. The amount is so large that any small saving that can be made effective in locomotive practice at once becomes an important factor in conserving the fuel supply of the nation. For this reason the United States Geological Survey gave attEmtion to the special problems of combustion in locomotive boilers. It approached this task from several different directions. The facts presented herewith constitute one series of results. In the fall of 1906 the locomotive-testing laboratory of Purdue University, at Lafayette, Ind., entered on a series of tests, one purpose of which was to determine in precise terms the degree of efficiency with which a modern high-class American locomotive utilizes the heat energy of the fuel supplied to it. The general interest in the subject, the elaborate plans which had been formulated for conducting the work, and the substantial character of the support which had been pledged to maintain it justified the Geological Survey in aiding the investigation. a The cooperation of the Survey consisted in detailing experts to assist the regular staff of the laboratory in the chemical and calorific work of the tests. These experts, working under the general supervision of the director of the Purdue laboratory, became responsible for the sampling of smoke-box gases, of the fuel used, of the cinders caught in the front end, of the sparks discharged by the stack, and of the refuse caught in the ash pan. The gas analyses were made by them at the university laboratory. The analyses of all solid samples and the calorific tests of the fuels were made at the government fuel-testing plant at St. Louis. The representatives of the Survey were not concerned with other phases of the work.

Jan 1, 1911

By Iain Finnie

This report is in three parts. The first part presents a review of theoretical models which have been developed to study removal operations for various types of materials. In the second part, a brief summary is given of coal cutting research. The majority of this work has been carried out in Britain using chisel type bits rather than the conical picks which are in general use in this country. However, a comparison of specific energies measured for conical picks in the laboratory and in the mine shows very encouraging correspondence. In the third part of the report, analytical models for coal cutting by picks are suggested. An extension of the British "tensile breakage" theory, developed for chisels, is given for picks. The role of crushing and cutting in coal removal is discussed as a theory which combines the two processes is shown to give reasonable predictions for specific energy requirements. Finally, directions in which the existing theory could be improved are presented and the need for further research is emphasized.

Jan 1, 1977

By N. P. Kripakov

The Bureau of Mines has developed a unique new mine design procedure to determine the changing static load distributions imposed on under-ground support structures during the mining cycle. The procedure reduces the complexities associated with analyzing a three-dimensional problem. A combination of the multiple-seam displacement-discontinuity model and a two-dimensional finite-element window model produces refined results for a specific area of interest by assuming displacement compat-ibility between models. Input to the procedure includes the geometry of mined-out areas in up to two adjacent seams, the rock mass characteris-tics of the surrounding geology, the in situ stress conditions, and the mining sequence. The displacement-discontinuity program calculates ex-pected loadings for mine structures affected by the mining cycle and/or by overlying or underlying seams. Pseudoelastic finite-element analysis using a yield-factor approach determines the stability of coal pillars by simulating the degree and extent of nrogressive rib failure and sub-sequent load transfer. Application of the procedure is demonstrated on a field problem. In-duced stress changes predicted from the numerical model analysis are in reasonably good agreement with stress measurements obtained from an instrumented chain pillar affected by remnant workings in an upper seam.

Jan 1, 1988

By Charles E. McCarthy

Part 1 of this report is concerned with the electric-furnace production of calcium aluminate and iron alloy from a variety of siliceous ferruginous ores of aluminum. The furnacing research was directed, first, to determine the extent of the field in the CaO-Al2O3-SiO2 system, in which calcium aluminates with the optimum leaching characteristics are obtained; second, to produce suitable quantities of these aluminate mixtures for pilot-plant leaching tests; third, to investigate the physical chemistry of the reduction reactions during furnacing; and, fourth, to study the economics of the process. The third and fourth steps were not completed. Part 2 comprises another phase of the work and will appear as a second Report of Investigations. It deals with the extraction of metallurgical-grade alumina from the calcium aluminate slag produced in the electric furnace and includes the following steps: leaching, desilicating, precipitating, dewatering, filtering, and washing of the aluminum hydrate. No claim is made that the data are complete, nor has the chronological order of obtaining data been followed. Rather, it is emphasized that additional work is necessary if the full possibilities of the process are to be evaluated. and made available.

Jan 1, 1949

By Kunihisa Katsuyama, Yuji Ogata, Yuji Wada

The one free surface blasting of a concrete block was simulated by Discontinuous Deformation Analysis(DDA) method. Comparing the simulated results with the concrete block blasting experiment, the crack growth and the free surface displacement which were simulated by DDA were observed with a high speed camera.

Jan 1, 1996

By G. van Aswegen

The geometry and morphology of a set of low-angle fractures around a stope in a deep Witwatersrand gold mine are explained in terms of extension fractures forming under variable conditions of stress. Primary extension fractures (E1) form some distance ahead of an advancing stope along the s1, s2 plane. With stope advance, a couple of these fractures end up in a stress regime conducive to transpressional shear and a secondary set of extension fractures(E2) is formed at a high angle to the primary fractures. i.e. at a low angle to the stope. As the E2 fractures are undermined, they migrate into a stress regime of transtensional shear and a third set of extension fractures (E3) may develop between E2 fractures. These have sigmoidal shapes, being parallel to the E2 fractures at the E2 discontinuity where s3 is negative, and curved through the un-fractured rock between E2 fractures where s3 is positive at the instant of fracturing. The fractures all display fractographic features characteristic of dynamic extension failure with striae indicative of the direction of rupture propagation and the local, instantaneous orientation of s1.

Jan 1, 2012