Search Documents

Jan 1, 1991

By M. F. Lopez, A. J. Mattus, S. B. Magid, D. B. Mobbs

"The use of Caro's acid as a replacement for hydrogen peroxide for the oxidation of vanadium prior to solvent extraction resulted in a 56% reduction in oxidant usage when compared on an equivalent hydrogen peroxide basis. Comparative oxidation tests, using two actual uranium mill raffinates, resulted in premature precipitation of an amorphous ferric vanadate when hydrogen peroxide was used to oxidize one of the raffinates containing a high iron to vanadium ratio. The use of Caro's acid eliminated the precipitation problem, thereby permitting the adjustment of the raffinate pH to a higher, more favourable level prior to solvent extraction.Potentiometric characterization of the raffinates revealed that vanadium is responsible for the inefficiency of hydrogen peroxide compared with Caro's acid, with the oxidation efficiency of iron being the same for both oxidants. A limiting potential between 720 and 740 mV was observed when using hydrogen peroxide, while, when using Care's acid, potentials approaching 1200 mV were achievable.A four-stage, countercurrent extraction performed on the oxidized raffinates did not reveal any operational problems. The extraction efficiency and the extraction coefficient were found to be higher when Caro's acid was used as the oxidant, as opposed to hydrogen peroxide.IntroductionMost vanadium is recovered as a by-product of some other process: leaching of Carnotite uranium ores, oil fly ash, phosphate rock or chromite processing. The major source of vanadium has been from uranium mills incorporating acid leaching of Carnotite ore s at elevated temperatures and pressures. The by-product recovery of vanadium from uranium ores of the Uravan Mineral Belt, located in the Colorado Plateau , is a common occurrence when vanadium recovery is economically viable."

Jan 1, 1983

By R. S. Warfield

The Kasna Creek copper deposit near Lake Kontrashibuna in the Lake Clark region, Alaska, was the object of an investigative project by the Bureau of Mines during the fall of 1948. Recessed because of inclement weather, it was completed in 1949. This project was a part of the Bureau of Mines program in Alaska for the development of critical and strategic minerals. The ore bodies are contact-replacement deposits in limestone. Mineralization is mainly specular and micaceous hematite associated with chalcopyrite, calcite, chlorite, quartz, and amphibole. The deposit, on the right limit of Kasna Creek approximately 2 miles from the shore of Lake Kontrashibuna, is composed of two mineralized zones that range in altitude from 2,350 to 2,650 feet. This report contains a brief history of the prospect, description of the physical setting of the property, its geology, and the factual results of the Work performed by the Bureau of Mines.

Jan 1, 1951

By A. Eccles

Phase designs are the foundation upon which all open pit mine sequence optimizations and budgets should be built. Unfortunately, at times, mine engineers skip the step of developing realistic pit phase designs - designs that include access ramps and mineable widths. Without mineable phase designs, their optimized schedules are based on theoretical pit shells or ?quick-and-dirty? plans with no ramps. The output from such optimizations is almost always overly optimistic. Without mineable designs, the production estimates are misleading, because they overestimate ore, and underestimate waste stripping requirements. Worse yet, when plans are not based on realistic phase designs, they can point to exactly the wrong decision in feasibility studies (i.e. ?go? when it should be ?no-go?). This paper discusses the importance and features of good pit phase design, and demonstrates the pitfalls of relying on optimized production sequences that are not based on properly designed pit phases.

Feb 27, 2013

By George A. Laird

I. INTRODUCTION. THIS old and once famous district played, through its enormous production of silver and gold, an important part in the history of the State of San Luis Potosi. According to a pamphlet prepared under the direction of the Governor of the State, Sr. Don Blas Escontria, and presented to the visiting members of the Institute during the Mexican meeting of 1901, this district is situated 20 km. east of the city of San Luis Potosi, in a range of mountains of moderate height, extending 135 km. N. and S., and 16 km. E. and W.; and the mineralized area hitherto developed is about 600,000 sq. m. The history of the district,. as given by the record dated 1778, and formerly kept in the San Francisco convent, says that it was discovered in 1575 by Sr. Don Pedro Irarte, and adds that the city of San Luis Rey de Francisco del Potosi received its name (in allusion to the famous Potosi mines in Bolivia) by reason of the remarkable productiveness of its gold- and silver-mines in the first period of their exploration, during which they paid to the Crown, as " quintos " (the fifth part of the product), $97,000,000, as appears from the accounts of the royal treasury. The amount of the quientos paid during the " bonanza period " of 80 years was $72,000,000. The larger sum first mentioned probably represents a longer series of years. But either will suffice to indicate the great wealth of the mines. In 1663, the decadence of the industry began with the caving¬ in of several mines, concerning which the record of 1778, al¬ready cited, says, in substance, that on Good Friday one of the owners in the enterprise, in view of the unfavorable prospect of a lawsuit in which he was engaged, set fire to the timbers supporting the underground galleries and workings of the San

Jan 1, 1905

High-pressure grinding rolls (HPGR) are an accepted, but continuously expanding, comminution technology. The copper industry has a growing need to process harder ores with progressively lower grades, more challenging metallurgy and increasing demand for efficient bacterial leaching applications. This has resulted in a major focus on HPGR use in a crushing circuit. If the industry is to increase leach extraction while lowering energy costs in high-throughput hydrometallurgical operations, HPGR will be of inherent significance. The following paper summarizes test work on copper leach ores utilizing the benefits of HPGR comminution, while increasing several critical metallurgical parameters. Based on the current work and previous investigations, it was found that HPGR comminution within a crushing circuit, in specific instances, can result in 2 - >10% increases in cop-per extraction. The tested variables are crush size, rock type and copper mineralogy dependence. Various other process parameters may also be optimized.

Jan 1, 2011

By Mario Aiezza

This paper outlines the results of a relationship developed during the design and construction of the foundations for the Gallery Towers project in Melbourne. Both the builder and the piling contractor were determined to arrive at a satisfactory foundation solution to the problems encountered at the site. The scope of piling work was to provide load-bearing piles under the building columns, some of which were located within a retention system that also required a piling solution. Geological conditions were variable and challenging. The site area was small and located adjacent to the National Arts Centre in the developed Southbank area, a high density office area. This presented logistical problems in limiting construction traffic on site and also demanding minimal noise and vibration emanating from piling activities. The piling contractor, Vibro-Pile, and the builder, Walter Construction Group, faced the challenges presented with a refreshing cooperative attitude that was beneficial to both companies. Commercial issues rising from design and construction problems were first put apart in order to allow the respective technical department of each company to work with minimum constraints to achieve the most cost effective solution. In the process usual adversarial attitudes resulting in loss of time and money was avoided. A number of issues were addressed successfully at minimum cost and time during this contract. Despite the difficulties encountered, the job was completed on time and with negligible claims for extras, resulting in the development of a strong mutual respect between both companies.

Jan 1, 2002

By W. P. Campbell

Introduction OWING to the necessity of curtailing the length of this paper, nothing like an exhaustive treatment of the subject will be attempted. Instead, merely a few aspects will be considered, viz., water trouble in wells, sampling of waters, analysis, methods of reporting analysis, and the comparison of a few typical waters. The waters discussed will not be confined to those occurring in areas where oil or gas has already been found, but will include samples from areas in which drilling is being carried on in the hope that oil or gas may be found, i.e., from unproved fields. The Water Problem The problem of dealing with water encountered in oil and gas producing areas has engaged the attention of petroleum engineers from the early days of the industry. Water was not always considered a menace to oil sands; indeed, a certain amount of it was considered beneficial in some areas, but if such exist today they are very exceptional. In some fields, the problem is more acute than in others, and at times has baffled all attempts to solve it satisfactorily. Wells have been brought-in with promise of good production, but after a brief period have 'gone to water'. Whether ?it has always been a case of poor engineering in the form of unsuccessful water shut-off of 'top' or 'bottom' water, or because 'edge' water was present and water and oil were in such close contact it was impossible to remove the one without the other, is hard to say.

Jan 1, 1929

DynoMiner APS Delivery Systems Overview ? New Design of DynoMiner APS-M2 ? Stand alone or attach to Cargo type 10,000 lb (4536 kg) emulsion bins. ? Hose reel w/200-ft (61-m) by 1-inch I.D (25-mm) hose capacity, power rewind. ? Increased water and trace capacity. ? Hose reel and gassing offered as options. ? New Flow Meter ? DN-100: aluminum body, UHMWPE rotors. ? Will be offered as an option. ? APS Nomenclature ? Proposed changes ? DynoMiner APS and APS-M1 to become DynoMiner APS Drifter ? DynoMiner APS-M2 to become DynoMiner APS Stoper. ? Both to have optional gassing / flow metering.

May 1, 2004

By Renfeng Song, Shaoyan Wang, Zhiqiang Zhang, Ke Guo

Leaching titaniferous magnetite concentrate with alkali solution of high concentration under high temperature and high pressure was utilized to improve the grade of iron in iron concentrate and the grade of TiO2 in titanium tailings. The titaniferous magnetite concentrate in use contained 12.67% TiO2 and 54.01% Fe. The thermodynamics of the possible reactions and the kinetics of leaching process were analyzed. It was found that decomposing FeTiO3 with NaOH aqueous solution could be carried out spontaneously and the reaction rate was mainly controlled by internal diffusion. The effects of water usage, alkali concentration, reaction time, and temperature on the leaching procedure were inspected, and the products were characterized by X-ray diffraction, scanning electron microscope, and energy dispersive spectroscopy, respectively. After NaOH leaching and magnetic separation, the concentrate, with Fe purity of 65.98% and Fe recovery of 82.46%, and the tailings, with TiO2 purity of 32.09% and TiO2 recovery of 80.79%, were obtained, respectively.

Jun 16, 2021

The Heavy Media Separation plant operated at Lidsdale siding, eight miles from Lithgow, by the N.S.W. Mining Co. is a product of the Western Machinery Company, of D.S.A.This mill, designed to use finely ground magnetite as the heavy medium, was prefabricated in America and shipped to Australia for erection.First operated early in December, 1951 it has worked on a two-shift basis since. Designed for an input rate of 330 tons per hour, this mill is capable of washing 4 in. x /u in. coal down to its inherent ash by removing all heavy material, including high-ash coal.The principle is quite simple. A stream of raw coal is fed into the separatory vessel which contains a liquid medium, the density of which is adjusted to produce the desired split between coal and refuse. In this bath the lightest coal floats, and all material heavier than the specific gravity of the medium sinks, and is removed separately. Such a system is,. ideally suited to Western coal, as there is no definite splitting point between coal and refuse. Inherent ash of the coal fed to the plant ranges from 8 to 25%, the corresponding density range being from 1.28 up to 1.8.Generally speaking, the higher the density the higher the ash content of the coal.The density in the separatory vessel (hereafter called the cone) can be quickly and easily adjusted throughout the above range to any desired value. Customer requirements, coupled with the economics of washing, dictate the proper specific gravity to be maintained. At present this is held at 1.52...

Jan 1, 1954

By Enguang Zhu, Kangning Zhang, Yang Li

"Due to the use of outdated mining technology or room and pillar mining process in small coal mines, the coal recovery ratio is only 10% - 25%. In many regions of China: the damage area caused by the small coal mines amounted to nearly one hundred square kilometers. Therefore, special mining techniques must be taken to reclaim the wasted resource in disturbed coal areas. This paper focuses on the different mining methods by analyzing the longwall panel layout and abandoned gateroad (AG) distribution in in the abandoned area of Cui Jiazhai Coal Mine in northwestern China. On the basis of three-dimensional geological model, FLAC- 3D numerical simulation was employed. The abutment pressure distribution was simulated when the panel face passed through the disturbed areas. The proper angle of the inclined face was analyzed when the panel face passed through the abandoned gateroads. The results show that the head end of the face should be 13-20m ahead of the tail end. The pillars on both sides of abandoned gateroads had not been damaged at the same time, and no large-area stress concentration occurred above the main roof. Therefore, the coal reserves of disturbed areas can be successfully recovered by using underground longwall mining. INTRODUCTIONDuring the 70-90's, there were a lot of small coal mines in China. Due to their disordered mining, most of the small coal mines left a great many abandoned gateroads (defined as AG in this paper) and a large area of damage coal seam. In these type of coalfields, there exist many mining risk issues, including nonuniform stress in the overburden, flooding and hazardous gases accumulated in the gob. So how to lay out a longwall panel and successfully mining under this type of abandoned small mines is a big issue nowadays in China.As mentioned above, longwall panel is being performed in the damaged coal seams in order to increase recovery of coal reserves (Wang, 2009). However, the abandoned geteroads intersect to each other all around the area. So a series of production issues arose while the panel face is passing through these AG. Gang and Gong (2015) analyzed the roof stability and abutment pressure distribution during the face was passing those AG that were parallel and inclined to the faceline. Xie, et al. (2015) proposed the ground control mechanism by passing the AG in top-coal caving longwall mining. He recommended to stop the face advance until the roof is over, using high strength bolts and cable bolts, and grouting consolidation. This paper studies the different mining methods by analyzing the longwall panel layout and AG distribution in damage coal seams. Theoretical analysis and field observation were conducted to determine the overburden movement when the face was advancing under the AG. The pillar between face and parallel AG changes from elastic to plastic and eventually to the residual supporting status. All these three status was combined with the roof structure to establish the theoretical model to calculate the shield support capacity. Numerical modeling was employed to simulate the pillar stability and determine the abutment pressure distribution as the face inclined to the AG during longwall mining."

Jan 1, 2016

By BUREAU OF MINES

This summary of State laws on explosives was compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and , in general , how they have been treated . It does not include any legislation passed after 1942 , or any proclamations , regulations , or administrative orders . It does not purport or attempt to be authoritative . If any problem arises involving interpretation of the statutes of any particular State , the original source must be consulted for the exact words used by the legislature . This summary , however , will be useful in determining whether relevant statutes exist , and in locating thern quickly, with a minimum of effort . It will be of value also in comparing statutes in one State with similar statutes in other States to determine what construction has been placed upon them by the courts of these jurisdictions or to contrast the varying provisions of many States upon a similar subject . To make these comparisons easier , the statutory provisions for each State have been grouped under several major topics in outline form . Although this sometimes has resulted in disruption of the continuity of individual acts , the increased general clarity and availability of comparable sections have more than justified the procedure followed ,

Jul 1, 1943

By Thomas M. Barczak

State-of-the-art longwall roof supports provide effective strata control, but failures of these support systems still occur. To identify failure mechanisms and the impact these failures have on the safety of the support system, the U.S. Bureau of Mines has been conducting research on shield mechanics in the Bureau's unique mine roof simulator, as well as field studies of in situ support loading and investigations of longwall failures, Three types of failures are discussed: (1) inadequate support capacity, (2) structural failure, and (3) instability. Hypothetical situations with proposed courses of action and case studies of actual longwall failures are described. This information is intended to assist the Mine Safety and Health Administration (MSEIA) and industry mining personnel in safety evaluations of longwall roof support systems.

Jan 1, 1989

By P. D. Rao, D. E. Walsh

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherit and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' remit research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Feb 24, 1997

By Arthur La Motte

I NDUSTRIAL explosives, as distinguished from military explosives, include high explosives and blasting powder. The high explosives which are best known are straight dynamite, gelatin dynamite, ammonia dynamite and permissibles. There are two kinds of blasting powder, saltpetre blasting powder and nitrate of soda blasting powder. Blasting powders are mechanical mixtures of nitrate of potash or nitrate of soda with sulfur and charcoal, highly compressed, granulated and glazed. They ignite from a spark and burn with relative slowness, the rate of burning and hence the rate of conversion into gases depending upon the size of the granulation and upon the degree of. confinement under which the powder is placed. High explosives, on the other hand, are chemical compounds which detonate; that is, when the explosive is subjected to a violent shock, provided in practice by a blasting cap or an electric blasting cap, the molecule of the essential ingredient, usually nitroglycerin, is disrupted and the energy and heat released cause any other explosive ingredients which may be present, such as ammoniuin nitrate or T.N.T., to decompose with a resultant evolution of gases at an extremely rapid rate varying from 6000 to 20,000 ft. per second.

Jan 1, 1924

This publication summarizes the Bureau's activities as part of a study of the Juneau Mining District (JMD) during the period 1984-1988. The objectives of the program were to identify the type, amount, and distribution of mineral deposits in the district, determine ore reserves, study beneficiation technologies for the ore, make feasibility studies, and address economic and legislative effects on mineral development. The JMD study was a cooperative study involving the Bureau and the Alaska Division of Geological and Geophysical Surveys (ADGGS). Over 30 employee-years were spent by the Bureau on this project. Bureau investigations in the JMD consisted of a district-wide investigation of industrial materials in addition to site-specific investigations of precious and base metals in five subareas. During the 4 years of the JMD study, more than 300 areas, mines, prospects, and occurrences were visited, which contain gold, silver, copper, zinc, lead, nickel, cobalt, tungsten, molybdenum, chromium, and platinum group metals (PGM). More than 59,000 feet of underground workings were mapped and sampled. More than 5,500 samples were taken; one diamond drilling program and three geophysical surveys were completed. An up-to-date and complete mineral data base for the JMD did not exist prior to this study. The JMD study, which coincided with a tremendous increase in mineral interest and activity in the district, has proven to be valuable to both the minerals industry and land management agencies. The discovery of two new mineral occurrences and compilation of data on known mines, prospects, and occurrences have aided industry activity in the region. The study enabled timely data to be available to land management agencies at the Federal, State, and municipal levels.

Jan 1, 2012

By W. G. K. Fleming

The general history of piling is traced up to the present time with regard to the evolution of methods and materials. The processes have been strongly influenced by developments in basic equipment and industrial change. It is noticeable that in the twentieth century more progress has taken place than in the many previous centuries. It has been strongly influenced by the general development of Soil Mechanics. Test loading is probably the most effective way to assess the success of designs and many empirical relationships have been challenged through it. As we approach a new century it appears that it will be an age of rapid equipment development, with much enhancement of understanding of what has been done. Processes of automatic construction and testing will becoming commonplace. These changes will narrow the limits of conventional scatter that have come to be accepted and to a large extent will be driven by political efforts to curtail energy consumption, to raise standards of quality and reliability, and to conserve the environment. 1. Ancient history. Piling is an ancient art. Its first mention in history is from Herodotus, the first person to commit an account of his times to the written word in the years 557 to 479 BC. He evidently had a strong interest in engineering matters because he wrote of building, brick making, reinforced brickwork, river training, canal building, bridge construction, tunnelling and its acoustic detection and piling. The piling reference comes from Book 5 at paragraph 16.

Jan 1, 1999

By F. M. Boler

The U.S. Bureau of Mines has configured a flexible data acquisition and analysis workstation, which incorporates control and analysis software written in-house for use in mining research experiments conducted in the laboratory and in operating underground mines. This data acquisition system combines computer-automated-measurement-and-control (CAMAC) modular instrumentation with a Unix-based graphics workstation. The data acquisition front-end hardware can be interfaced to almost any computer. CAMAC instrumentation modules adhere to mechanical, electrical, and digital interface standards and can be custom designed or purchased off the shelf. Communications along the CAMAC bus are regulated by the crate-controller module, which contains the only hardware link to the computer interface. Software support for the data acquisition and analysis workstation consists of a series of functions and programs written in the "C" programming language designed to provide flexible and fast data acquisition, processing, and analysis. The user can interactively control the digitizers and other CAMAC modules by sending standard CAMAC read, write, and command function codes from a menu-driven program. Automated data collection is achieved through software that responds to hardware interrupts triggered by acoustic emission or microseismic events. Graphics display routines are used to plot part or all of the data and provide the ability to process and store signal information selectively.

Jan 1, 1990

By Bijan Taheri, Behrouz Maghsodi, Monireh Heshami, Reza Kohan

A common problem recently encountered with the increase in the rate of input feed at Enrichment Plant 2 of the Sarcheshmeh Copper Complex is the loss of value to the tails, translating to lower recoveries. The feasibility of the direct transfer of part of the high-grade concentrate from rougher stages to an appropriate position along the circuit was studied, and two positions were proposed for direct transfer of the concentrate. One position was the feed flow into cleaner cells, and the other was the feed flow into the recleaner cell. The results indicated that transferring the concentrate from the first unit of the rougher stage to the feed flow into the cleaner cells was feasible, with no limitations, while the second position required the installation of a set of hydrocyclones. It was found that the transfer of concentrate to the proposed positions not only addressed the problem of limited cell capacity, resulting in debottlenecking of the circuit, but also improved metallurgical separation efficiency up to 1.4%.