Search Documents

By R. E. Wilmot

This paper is based on the experiences, over many years, on the part of numerous authors in the South African mining industry and that of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a practical example; ?case history? where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions to be encountered in a new mining operation (now 10 years on) and concludes with two follow up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2006

By A. Nuric, S. Nuric, L. Kricak, M. Negovanovic, S. Mitrovic

"SynopsisRotary drilling with rolling tricone bits is the most widely used method for drilling large-diameter blast-holes in large surface mining operations. This drilling method is applicable to a wide range of soft to hard rock materials. This paper presents a fuzzy model for predicting the penetration rate of tricone rotary blast-hole drilling. The model is based on data obtained during the drilling of blastholes in rocks with various uniaxial compressive strengths in the Veliki Krivelj open pit mine, Bor, Serbia. The model was developed using the fuzzy logic toolbox of MATLAB with the Mamdani inference system. The fuzzy model was tested with 23% of the total dataset. The results obtained show the high reliability of predicting the penetration rates. Although there are possible limitations in applying the model to other open pit mines because of differences in rock properties, the prediction methodology applied in this paper can be used in many other predictions of the penetration rates.IntroductionAccording to Tamrock, rotary blast-hole drill operations depend on four important elements:•,Torque in the drill string drive sufficient to turn the bit in any strata encountered•,A high bit loading capability (pulldown force) sufficient for optimum penetration•,An air volume sufficient to remove chips generated during the drilling and to provide cool air to the drill bit bearings•,The selection of the proper type of bit for the material being drilled (Tamrock, 1984).The effects of rock mass parameters on the choice of the type of tricone bits were investigated by Kricak (1997)."

Jan 1, 2015

By Martin B. Hudson, Daniel Brescia, Zhangwei Ning

Due to the complexity and sensitivity of surrounding environments, instrumentation and monitoring (I&M) is critical for many urban deep excavations. The objects to be monitored include shoring bulkheads, retained embankments, adjacent buildings and roads as well as underground utilities. However, there are also plenty of constraints on the implementation of I&M such as: congested site space, difficult access to instruments, coordination among multiple contractors, and installation permits for private or public properties. Because of these constraints, sometimes the implementation of the initially planned I&M is delayed, its scope is reduced, and/or the continuity of monitoring is interrupted. For these reasons, it is important to implement the I&M with robust and redundant capabilities while providing minimal interference to the project construction and schedule. This paper describes state-of-the-art I&M technologies including automatic motorized total station (AMTS) with camera and automatic leveling device, reflectorless AMTS and IoT- based wireless sensors based on a case study of an on-going deep excavation project. INTRODUCTION In urban environments, deep excavations requiring the construction of temporary shoring bulkheads are becoming increasingly common, with the associated need to provide protection of the surrounding built environment during construction. Protection of the surrounding environment requires planning, engineering, construction, monitoring, and excessive shoring movement mitigation. The I&M is a vital component of the deep shoring implementation. In public projects, geotechnical I&M is often placed within the general contractor’s scope, whereas the majority of deep excavations are privately undertaken. For those private developments, sometimes the developer contracts the geotechnical I&M directly with the project geotechnical engineer or by a geotechnical I&M specialist hired by the project geotechnical engineer. In either the public project or private development case, the effective deployment of the I&M system relies heavily on coordination and collaboration with the project contractor.

Jan 1, 2018

By B. C. Alberts

Planning the use of South Africa's energy resources, especially coal, is of the utmost importance. The State and the mining industry require reliable official estimates of the economically mineable coal reserves for planning purposes. An overview of al the previous reserve estimates is given, with specific attention to the two most recent estimates-those of Petrick and De Jager. The differences between these two estimates are highlighted. The following important aspects are discussed: . the need to update the information regarding South Africa's mineable coal reserves, . the necessity of understanding and agreement between the coal-mining industry and the State department responsible for updating the coal-reserve data, and . the importance of the specific assumptions used in the updating of the data. A downward adjustment of mineable reserve figures is proposed, and the factors that influence the meaningful exploitation of the coal reserves are discussed. A recommendation is made as to how the Waterberg coal reserve should be exploited, and it is concluded that the Soutpansberg Coalfield cannot be exploited economically in the foreseeable future. An evaluation of the status of the coal-export trade is made and compared with the assumptions and targets set at the start of the coal-exportation scheme. The comparison shows the extent to which the exploitation of the coal reserves is being negatively influenced by the current market situation. Recommendations are made regarding planning for the coal-export market, and the aspects that have to be taken into account to keep South Africa in the export market are identified. Reference is made to the fact that the present unrestrained wage and salary adjustments, which show a total disregard of South Africa's poor productivity record, require serious thought and speedy rectification if the country is to survive in the export market. A salary and wage strategy must be developed to suit the specific needs of the Republic of South Africa.

Jan 1, 1987

The Bureau of Mines is active in programs pertaining to solid waste disposal and land reclamation. Nine reclamation projects of mining companies and six projects of the Commonwealth of Pennsylvania were investigated to provide information on the procedures, costs, and results obtained from reclamation projects of bituminous coal-waste disposal areas. Refuse disposal costs of mining companies ranged from 9 to 28 cents per ton-mile, and quantities disposed of ranged from 600 to 4,500 tons per day. Spreading and compacting the refuse at the dump site ranged from 3 to 20 cents per ton. Cost of covering with soil and planting ranged from $750 to $1,646 per acre. Total costs of reclamation for the Pennsylvania projects ranged from about $1,800 to more than $15,000 per acre. Refuse preparation costs ranged from $772 to $5,550 per acre. Soil covering and planting costs ranged from $1,083 to $5,086 per acre. The best results were obtained by soil preparation and conditioning prior to planting. The type and depth of soil and effect of climate were also factors.

Jan 1, 1973

Remediation of Mine Seepage at Batu Hijau

Sep 13, 2010

By J. J. Forbes

Probably the newest thing in mining safety, or safety for mines, is the apparent dissatisfaction on the part of the mineral industries, as represented by both management and labor, and the general public of the Nation, with the safety record of the mining industry. This is reflected by published comments and papers in the technical press;1-8 in labor periodicals, 10 11 in popular journals and periodicals,12 13 and in the daily press; also by discussions of the Safety Committees sponsored by the National Safety Council, 9, 14-15 the American Mining Congress, 1, 16 the American Institute of Mining and Metallurgical Engineers, 2, 4 the Mine Inspectors' Institute of America,6,8,17,18 the Coal Mining Institute of America, 5, 19, the American Standards Association, and others.20,21

Jan 1, 1949

By E. M. Stiles

THE Wellington Lake power plant of the Consolidated Mining and Smelting Company of Canada, Limited, about 25 miles from Goldfields, Saskatchewan, is the second hydro-electric project operating in that Province, the first being the Island Falls plant of the Churchill River Power Company which serves the operations of the Hudson Bay Mining and Smelting Company at Flin Flon, Manitoba. The Churchill River project develops 90,000 h.p. at 56-ft. head; the Wellington Lake plant 3,300 h.p. at 75-ft. with pro-vision for an additional 3,300 h.p. unit. Churchill River power is trans-mitted at 110,000 volts over a 58-mile line of steel towers to Flin Flon and an additional 45 miles over a wooden pole-line to Sherritt-Gordon. Our steel tower-line is 22 miles long, and the voltage is 60,000; this choice be-cause certain such equipment was available from Trail. The diversion of 15,000? second-feet at 56-ft. head for 90,000 h. p. at Churchill river dwarfs our 500 second-feet flow at 75-ft. head for 3,300 h.p. In both cases, the main obstacles to be overcome during plant construction were the lack of transport facilities and the short open season. Let it be noted here that this paper deals mainly with those phases of plant construction which were particularly interesting to the writer. With-out these variations from the ordinary routine, this is just another power project whose story is better told by the accompanying charts and pictures. To many members of the Institute it is still just that; but I am writing for those who, like myself, have been too seldom responsible for major under-rakings at an appreciable distance from a railway siding. When it was planned in early 1937 to erect a 1,000-ton mill at our Box mine, both hydro and Diesel power were discussed. With ten years' ore in sight, even an expensive hydro project, such as ours turned out to be, produces kilowatts materially below the 2-cent operating cost of a Diesel plant using fuel-oil at 14 cents a gallon.

Jan 1, 1940

By Patrick E. Durnal

The Richmond-San Rafael Bridge was built in the early 50s' and was first opened to traffic on August 31, 1956. Among California's longest steel bridges, it spans more than 21,000 feet across the northern portion of San Francisco Bay. It is one of six toll bridges currently undergoing seismic retrofit in the Bay area. Current retrofit criteria require the structure not to collapse in a Magnitude 8.3 earthquake lasting 45 seconds on the San Andreas Fault. The earthquake epicenter is 10 miles to the west of the Bridge, near the mouth of San Francisco Bay. Another major fault is the Hayward Fault, with a potential of a 7.5 magnitude earthquake. It is only 4 miles east of the eastern end of the bridge. The retrofit criterion is that the structure survives these earthquakes without collapse or loss of life, and that they are capable of repair within a period of one year. Therefore an energy absorbing, ductility and nominal resistance based approach to the retrofit design have been adopted for the retrofit of this bridge. Foundation Retrofit The foundation retrofits were designed to satisfy of drift criteria of 6 inches at the base of the footings, and to keep the existing H-piles from experiencing unacceptable levels of permanent soil displacement and /or structural rupture. Full-scale structural lateral load testing of BP14x89 piling, to rupture, has helped to determine the drift criteria. However recent non-linear analytical results, have led to a redesign, which may allow for 12 inches of drift. The as-built analysis of the Micropile piers determined that those piers would not exceed the 6-inch drift criteria so lateral resisting shear piles were not needed at those piers.

Jan 1, 1998

By John S. Ball

Aniline points have been used to some extent for more than 20 years. to indicate the types of structures in hydrocarbons and thus to analyze mixtures of hydrocarbons . This type of analysis has been applied - principally to the low -boiling hydrocarbons found in the gasoline range . Although there is some disagreement as to their merits , both aniline point and diesel index (aniline point in degrees Fahrenheit times A.P.I. gravity at 60 ° F. divided by 100) are used rather extensively for evaluating ignition qualities of diesel fuels . In recent years aniline points have been employed in the study of lubricating - oil fractions . They also have been used to predict : the tendency of different oils to cause swelling of synthetic rubbers.5/ Recent standardization of the aniline - point determination by the American Society for Testing Materials has encouraged wider use of this test . Considerable data concerning , aniline points and critical solution temperatures in aniline have been accumulated in the course of a study of related subjects . Thesc data , together with some original results , are presented here in the hope that they will prove useful to other worker's in this field ...

Oct 1, 1943

This report describes the development of training materials for the operators of underground mining equipment in the underground metal and nonmetal mining industry. The objective was to determine the effectiveness and acceptability of these training materials and to provide the validated training materials to the industry. Ten modules were developed, based on industry need according to accident frequency, accident severity and exposure to the equipment. The final modules were an average of 20 minutes in length and used slides with synchronized narration on cassette tapes. Testing materials are included for use by the mines.

Jan 1, 1984

By P B. Hills, R J. Walton

Geotechnical instrumentation has been implemented as a key step for monitoring and optimising an engineered mine design for managing seismicity at the Beaconsfield Gold Mine. Measurements of displacement, stress change, ground control element load and seismic response of the rock mass allow for back analysis and calibration of critical parameters for feedback into the engineering design loop. Instrument clusters are installed in strategic locations prior to the commencement of stoping in order to determine the nature of the response of the rock mass to stoping. A selection of instruments including instrumented cable bolts and rod extensometers, resistance wire extensometers, hollow inclusion stress cells, vibrating wire stress meters and resistance wire extensometers are used to gather data through a data logging system. The rate at which data is recorded is adjusted to provide more information during periods of anticipated rapid change such as around stope firings or during periods of high seismic activity, and less information during periods of anticipated quiescence. The twofold purpose of the instrumentation is to calibrate the numerical modelling output which forms the basis of the engineered mine design, and to provide an alert mechanism where the behaviour of the rock mass is not what was anticipated, or where the impact of that behaviour may compromise the integrity of the engineered ground control system. The paper describes the location of instrument clusters with respect to stoping, the type of instruments employed and the method of data acquisition. It provides examples of results obtained and illustrates the way in which that information is used to optimise the mine design and manage seismicity.

Jan 1, 2008

By J S. J van Deventer

"Conventional wisdom is that gold not assayable is not recoverable or does not exist. There has been no formal study on the possibility that gold assays using advanced spectroscopy such as mass spectrometry and neutron activation could grossly underestimate the gold recoverable by proprietary extraction techniques. Such gold is not considered here to be æinvisibleÆ to detection but rather æabnormalÆ or ædistortedÆ at atomic level. Large-scale extraction of gold from æabnormalÆ ores has not been demonstrated, hence this emerging field still lacks credibility and acceptance. For fear of harming their reputation, few academic researchers or companies are expected to venture into this field until it is well proven. This paper aims to create awareness amongst metallurgists of the potential of æabnormalÆ gold ores by reviewing unconventional observations, the pseudoscience mainly available in non-peer reviewed web sites, and hypotheses for the recovery of ænon-assayableÆ gold, including: the occurrence of high levels of nano-sized gold in clays detectable by high-precision analytical instruments, which represents æinvisibleÆ gold accounts of ambient transmutation of elements, mainly using thermal methods orbitally rearranged monoatomic elements (ORMEs), which are virtually undetectable by conventional means, and their conversion to normal metals the possibility of a æhigh spinÆ state of transition metals the formation of microclusters altering the chemical behaviour of gold and the possibility of clustering with other elements. It is suggested here that gold in ores displays a range of clustering, from ænormalÆ gold amenable to conventional extraction to the ORME state. The concepts of æintermolecular waterÆ in forming complex salts locking up precious metals, electro-dissolution in strong acids, and electrowinning at both the anode and cathode are discussed as a means of treating æabnormalÆ gold ores. It is also possible that the gas phase extraction of gold chlorides under controlled temperature and pressure conditions, as well as transferred-arc plasma fuming of gold through carbothermic reduction of sulfides, could be used as a basis for extraction of gold from æabnormalÆ ores.CITATION:van Deventer, J S J, 2013. Is there gold that we do not recognise?, in Proceedings World Gold 2013, pp 27-34 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

By Wilson Blake

This report presents the results of a 7-year Bureau of Mines program to review, revise, and make an effective engineering tool of the microseismic method of determining the stability of rock structures. The program consisted of developing new microseismic equipment and data analysis techniques and extensive field investigations to demonstrate the effectiveness and potential of the broad-band microseismic method. The guidelines for choosing the components of a microseismic system are presented along with approximate cost figures. Different microseismic systems are discussed, including completely automated systems. Procedures for conducting microseismic investigations and analyzing microseismic data are discussed in detail. Field situations which show the full value of the microseismic technique as an engineering tool are described.

Jan 1, 1974

By AIME

Burton J. Westman-Besides decreasing the diamond size, there appear to be two other approaches open to overcome excessive diamond loss and, more particularly, the rapid diamond polish that took place in this quartz-feldspar rock. First, however, a short discussion of the diamond characteristics should be made in order to discuss the situation more clearly. The West African diamonds which we can assume were used. for this drilling have two disadvantages when drilling hard, exceptionally fine-grained rocks. These are rapid polishing and, if .the bit isn't "drilled in" carefully, a tendency to damage, resulting in excessive diamond loss. The normal wear resistance of any diamond is inversely proportional to the compressive strength of the diamond, therefore only the highest grade, of diamonds free from insipient fractures should be employed. Using upwards of 90 diamonds per carat instead of the20 to 30 per carat not only decreases the total projected area of the cutting points but increases the stress per point which, in turn, causes greater depth of penetration into the rock. Considering this depth of penetration, therefore, suggests an approach other than increasing the, number of diamonds per carat and that is to decrease the actual number of diamond points (also the carat weight per bit) so that the penetrating force on an individual diamond is increased. This penetration increases the chipping or rock shearing action.

Jan 1, 1950

By T. P. Meloy

A methodology is presented for finding feasible or locally optimal designs in the class of homogeneous, countercurrent, processing networks performing two-component non-sharp separations. The advantage of the methodology developed here is that given a set of independent performance criteria (specifications such as network separation factor, beneficiation ratio or recovery), a feasible or locally optimal countercurrent network design meeting those criteria can be found in one step. In the methodology, graph-theory was used to explicitly obtain the exact network responses of specific countercurrent networks. These responses were used to formulate the linear recursion equations whose solution gives the expressions for the countercurrent network responses which are a function of the stage transfer functions for two-component, non-sharp separations. These expressions are also functions of the network variables n and c. These expressions, together with the set of independent design criteria, were solved simultaneously for n and c using the Levenberg-Marquardt algorithm for systems of constrained, non-linear equations. The network variables n and c embody the coded network design information which is used to find the feasible network design which satisfies the set of independent performance criteria.

Jan 1, 1994

By Catharine T. Fogg

The Bureau of Mines investigated the availability of flake and high-crystalline natural graphite from 4 domestic and 25 foreign mines and deposits in 11 market economy countries (MEC's). Demonstrated resources were estimated to be 95 million metric tons (Mmt) containing 5.61 Mmt of recoverable flake and high-crystalline graphite products. Fifty-five percent (3.17 Mmt) of the total recovered product is estimated to comprise plus 100-mesh (150-µm) flake pro-ducts and "lump" and "chip" high-crystalline products, designated as "graphite A" in this study; 45 pct (2.44 Mmt) of the total is minus 100-mesh (150-µm) flake products and "dust" high-crystalline products, designated as "graphite B." Total production costs, including all costs needed over the life of each operation, were determined at a 0-and 15-pct discounted-cash-flow rate of return (DCFROR) for both graphite A and graphite B products. For a 15-pct DCFROR, 1.74 Mmt (54.9 pct) of the graphite A products is available at $600/mt or less and 2.13 Mmt (67.2 pct) is available for $800/mt or less. For the same DCFROR, 1.08 Mmt (44.3 pct) of the graphite B is available at $200/mt or less, and 1.71 Mmt (70 pct) is available at $325/mt or less. No domestic resources were determined to be economic at present prices. A sensitivity analysis of the relative economics of the Alabama graphite deposits under various operational parameters is presented in an appendix. All evaluations are in January 1984 dollars.

Jan 1, 1987

PRESIDENT MARKS: This is a matter, I think, in which we are all very much interested, and I know We will have considerable discussion on the subject. MR. GIBSON: Wouldn't it be a fact, Mr. Trick, if a mine was laid off on the block system, it would require less ventilation, less cubic feet of air per minute, and therefore you would have that much better ventilation by

Jan 1, 1926

By R. H. Winn

A method for the selection of the most suitable corrosion inhibitor for a particular system is given. The method involves the evaluation of surface passivity by means of copper ion displacement after the metal surface has been subjected to the corrosive atmosphere. The application of the method to the selection of suitable inhibitors for use in producing wells is described. Correlation with recognized laboratory tests has beet1 found to be good within the limitations of the test. The use of the test to evaluate inhibitor persistencc is described. INTRODUCTION Corrosion as it is associated with the industry shows wide variations in its qualitative as well as its quantitative aspects. This complicates the work of the corrosion engineer. In the past few years the efforts of the corrosion engineer have been further taxed by the large numbers of products being marketed as corrosion inhibitors by various manufacturers. These products are submitted to him together with a limited amount of data to support their use as inhibitors. The data are usually authentic and reliable yet all too often when these products are applied to an actual corrosive system the results are disappointing due to the ineffectiveness of the inhibitor and the corrosive system. The corrosion engineer must select a comparatively limited number of inhibitors for field trial from the large number available. The selection is usually made on the basis of a standardized laboratory test such as that adopted by the National Association of Corrosion Engineers or by field experience in an area; however, testing of this type is discouraging on large numbers of compounds, particularly in view of the specificity of environment. It has been an object of this work to devise a method which will allow the corrosion engineer to select the best inhibitor for a specific environment under field conditions. The test would of necessity be rapid and inexpensive. It would preferably eliminate the need for expensive and delicate instruments. STATEMENT OF THEORY The test as developed makes use of the fact that metal ions will be displaced from solution by metals having a more positive electrode potential. Thus, if an active iron surface is exposed to a solution of a copper salt, free copper will plate spontaneously on the iron surface as it is displaced from the salt solution by iron ions. If the iron surface is passified, as by coating with an insulating-type organic corrosion inhibitor, it is no longer capable of displacing the copper ions due to its own limited ionization. The result will be a change in the amount of copper plated upon exposure to a neutral copper salt solution. In practice it has been found possible to measure the magnitude of the alteration of the cell potential by determining the copper deposited on a standard iron surface under controlled conditions. This means that, as the film builds up, the resulting shift in the electrode potential tends to cause the iron surface to act more like a noble metal, resulting in a reduction in the cell potential to a point that copper will no longer plate spontaneously. Obviously, the salts of other metals such as silver, gold or platinum might be used for this operation; however, copper was selected because of the color difference of the plate, the comparatively low cost of copper salts and the ease of evaluation of the plated copper. Furthermore, its high cell potential provides a substantial driving energy. The determination of the copper is readily done colorimetrically by dissolving it in 5 per cent ammonium hydroxide solution containing 2 per cent potassium per-sulfate. The blue color of the copper ammonic complex ion so developed may be compared with standards prepared by dissolving known quantities of copper powder in the same reagent. In routine screening it is seldom desirable to determine the amount of copper plated. It is usually more important to determine the concentration of inhibitor required to prevent the plating of copper.

By I T. Ross

In the last 50 years there have been tremendous improvements in equipment used in development on underground mines. Compressed air powered jacklegs have been replaced by high powered electro-hydraulic drifters on sophisticated drill jumbos and load haul dump units have taken over from small shovels and rail cars.Despite the increase in power applied in key parts of the development cycle, average advance rates have fallen and costs have increased. The factor that is most often regarded as the main contributor to slowing advance rates is increased support requirements. Whilst there is no denying that the drive to improve safety has resulted in the requirement for more bolting and the installation of a skin support (mesh or shotcrete), this is not the only factor.Within the industry as a whole, many of the basic principles of development appear to have been lost over time. This paper looks at a historical case study and discusses some of the features of old development cycles that are no longer in use. This highlights some of the basics that appear to have been forgotten. These may be indicators to what may provide improvements in the conventional drill and blast development cycle.CITATION:Ross, I T, 2014. Development – back to basics, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 67–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014