Search Documents

By Donald W. Mitchell

Research shows that water neutralizes the explosion hazard of coal dust when present in sufficient quantity and when intimately mixed with the dust. The quantity of water required to neutralize coal dust and coal-rock dust mixtures is about equal to the limiting moisture adsorptive capacity of the dust; the adsorptive capacity increases with increase in the fineness and volatile content of the coal. Pools of water or high atmospheric humidity do not reduce the explosion hazard. Although wetted dust is less dispersible than dry dust, poor dispersibility cannot be relied on as the sole safeguard against explosion. Dust mixtures that contain water in excess of their limiting adsorptive capacity are dispersed and ignited by severe initiation sources. Pure coal dust adsorbs water with difficulty and retains water poorly; adsorption and retention is increased by the addition of rock dust the coal; the rock dust agglutinates wetted coal and assures that incombustible is present should drying occur. Therefore, it is advantageous to rock-dust wet areas in bituminous coal and lignite mines. When coal-rock dust mixtures are wetted and subsequently dried, the explosion hazard is about the same as for dust which was not wetted.

Jan 1, 1962

This is what I term ... the graveyard end of any Conference. It's almost over. Those of you remaining are either all talked out or past the information overload stage. And some of the sensible? ones have left for more exciting field trips, or gone back to their work-site where they earn their daily crust, or headed off South to another Conference of interest to the Energy sector that is being held currently in Christchurch. But that's OK. I have a thick skin! And neither am I particularly Politically Correct! I am not a miner: I am not involved in the mining industry in a hands on way at all. I am not even an academic. I am not even too sure why I am here ... apart from the fact that I agreed to come! At various times in my life I have been a D istrict Councillor, Chairman of a Regional Council and even an MP. I am a supporter of responsible mining.  All of what I have to say is my own point of view rather than that of either the Coal Producers' Federation or the mining industry. That is not to say that we are often in agreement, but I thought I would clear that point right at the outset. And some of what I will talk about will not strictly be to the topic - it's hardly mind-bending riveting stuff. Well, is it? But obviously because you are still here you have some interest in the topic.

Jan 1, 1997

By Steven A. Hawkins

This report details the conduct and results of a 5-month study to collect data on the use of steel support for ground control in European underground coal mines. The report summarizes European steel support design practices and describes the applicability of steel supports to U.S. mining conditions.

Jan 1, 1980

By Johnston W. H

MINING operations in the Waihi mine began, under the present proprietorship in the year 1889. Previous to this, and as far back as the year 1880, the presence of reefs in the Martha Hill had been known, and surface working on a small scale had beencarried out, without any great measure of success. The only method of treatment in use at this time was the old system of light stamps, amalgamating tables and berdans, and recovery by this method being low, little margin for profit was left, so thatthe property in these days was not considered of great importance and work on the area was only carried on spasmodically by different owners.On the transfer of the leases to the present company, calcining, dry crushing, and hot pan amalgamation was adopted as the method of treatment, and this system was continued till the more modern cyanide process was introduced and applied. As themethods of treatment and gold-saving became more efficient with the application of more modern and scientific processes, the importance and future prospects of the mine became more and more pronounced, and mining on a larger and more comprehensive scale was gradually established.As in the case of ore treatment, mining methods in the early stages were not as far adv.anced as the adopted practice of today, and numerous shafts, levels close together in vertical height.

Jan 1, 1912

By K. Zeidler, T. Schwind

The Fort Canning Tunnel, Singapore, is an approximately 50 feet (15m) wide vehicular tunnel under shallow ground cover that has been constructed according to the principles of the NATM. Its shallow location in soft ground combined with a high groundwater elevation in close vicinity of historically important features called for special design considerations combined with a rigorous monitoring scheme. Surface, sub-surface and in-tunnel instrumentation was installed to monitor the performance of the ground and tunnel support during construction. Comparison of actual reading data with the results from the computer modeling carried out during the design phase is provided in this paper.

Jan 1, 2007

By P. C. Dagneau

QUEBEC CARTIER MINING COMPANY was incorporated in 1957 to explore and develop low grade iron are deposits in Northeastern Quebec. Four separate deposits were located and identified as being of ore quality and size to support commercial development. Said deposits were located at Lac Jeannine, Mount-Wright, Fire Lake and Mount-Reed. In 1970, in preparation for the replacement of the depleting Lac Jeannine are reserves, construction of an SS-mile railway extension was initiated, towards the newly selected mine site at Mount-Wright. This orebody was selected because the physical and chemical characteristics of the ore were very much similar to those of Lac Jeannine, as well as its huge reserves, estimated at more than one billion tons. In addition to the railroad extension, a mine, concentrator and related facilities were constructed and the new town of Fermont was created. Total investment for the Mount-Wright project exceeded $700 million and initial production commenced in 1976. Quebec Cartier is presently (1992) the leading producer and seller of iron ore in North America at 15,5 million tons and employs some 2,300 people.

Jan 1, 1993

By Beevers J

The Ok Tedi Project is now a high production open-pit porphyry copper mine located in the Star Mountains of Papua New Guinea (PNG). At present, total daily production is 190 000t of ore and waste. Large scale drilling and blasting has only been in operation since 1988, prior to which all material was removed by ripping and dozing. This paper reviews the steps taken over the last 12 months in establishing a more efficient drilling and blasting operation and highlights the significant reduction in powder factor. These improvements have been achieved largely through the introduction of air-bags, controlled pattern expansion and an overall focusing on the operation by involving consultants, ICI's technical service and internal departments.

Jan 1, 1991

By J Sigda, T Jones, D Staggs, J Ewing, C Cheng, J Pickens, S Paulka

Mine-derived solutes from Energy Resources of Australia’s (ERA’s) Ranger uranium mine have been closely monitored for decades. Ranger is surrounded by the Northern Territory’s Kakadu National Park and is upstream of Ramsar convention wetlands. Modelling of groundwater flow and solute egress from mine wastes to surface waters has helped ERA successfully assess closure options and secure intermediate regulatory approvals during the site closure process. Potential environmental impacts were assessed using groundwater modelling in support of three ERA applications involving disposal of tailings-derived mine waste. Model results were an important part of the basis for obtaining regulatory approval. Three case studies are presented describing the three applications and how the groundwater modelling supported approval of the applications. For case study #1, INTERA supported ERA in addressing stakeholder concerns in 2017 regarding two aspects of tailings deposition in Pit 3. The first was the potential for flow of tailings fluid into the surrounding formations during tailings deposition. The second was the difference in post-closure magnesium (Mg) loading to surface water for two tailings deposition scenarios. INTERA developed a two-dimensional (2D) model that showed excess tailings pore pressures would not cause outflow and solute egress from the pit during deposition. INTERA’s three-dimensional (3D) models demonstrated that post-closure Mg loading to creeks for both tailings scenarios differed marginally and would be a small fraction of natural creek Mg loads. The modelling results helped avoid delays in completing tailings deposition driven by stakeholders’ environmental concerns. Case study #2 consisted of supporting ERA’s 2019 request for approval to change the tailings deposition method and final tailings level in Pit 3. INTERA’s model results for the permitted and proposed deposition methods showed minimal differences in post-closure Mg loading to creeks. The model results helped ERA obtain the needed approval for the tailings deposition method and water and tailings levels in Pit 3. For case study #3, INTERA modelled the comparative impacts from leaving the entire contaminant plume from the temporary tailings storage facility (TSF) in situ or excavating a portion of the contaminated material from beneath the TSF floor and placing it in Pit 3. The modelling results supported an approved TSF contaminated material application important for ERA to stay on schedule and minimise both closure costs and environmental impacts.

Jul 1, 2021

By L. C. IlsLey

One of the details which the engineers observe closely in conducting tests on explosion-proof type equipment at the Pittsburgh experiment Station of the Bureau of Mines is the construction of covers and their means of fastening. These covers are of particular concern from a safety standpoint, because they are very liable to be frequently disturbed for the purpose of making inspection or repairs to internal parts of motors, controllers, etc. When depended upon to permit frequent inspections it is desirable from a practical operating standpoint that the cover be easily and quickly removed and replaced. The position that been taken by the Bureau of Mines is that the questio of ease with which covers will permit inspection should be determined by the mamu- facturer and the user. If the scheme used requires considerable effort, as in the removal of several bolts, it has been assumed that the one going to all this trouble to get the covers off could be trusted to put the cover back in place properly, especially as the approval plate generally calls specific attention to this point. Where a cover is simply screwed in place, fastened by a single bolt, or secured by a hing in or other similar arrangement, the bureau has not been willing to assume that the, cover would in all cases be properly fastened and has required further security by means of a lock or seal. In the course of its investigations the bureau has had occasion to inspect and test five types of covers as follows: (1) Covers having two plane surfaces bolted together. (2) Covers having two plane surfaces held together by lugs, clamps, or other means besides bolts. (3) Covers which have screw thread and fit a similar thread in the compartment. (4). Covers having plane surfaces with the addition of a tongue-and-groove joint at about the center of the plane surface and in general secured by hinge pins or similar means of fastening. (5) Covers in the form of an annular ring accurately fitted to a motor shell which can be rotated around the shell, and thus make easy access to inspection openings in the shell and rotated back again to effectively seal these openings. Tests. have also been made of large bolted covers having a smaller and more accessible cover within the large one, which could be opened for inspection purposes.

May 1, 1930

By Claude Bodeving

The present steel economy drastically increases the financial strain on blast furnace operators. As a consequence, the importance of reliable cast floor operations is increasing drastically, which has a direct influence on the required clay mass and tapping equipment performances. When using modern high performance clay masses, pneumatic taphole drilling machines quickly reach their performance limits, which has made fully hydraulic drill hammers a standard in modern cast house operation. Besides the well-established hydraulic TMT hammers with high impact energy, an alternative version with lower impact energy, but high impact frequency was developed by TMT in the past, in order to achieve improved taphole protection. TMT’s recent research has shown that the drilling requirements inflicted by the taphole condition change over the taphole length, which has triggered the development of a new hammer, capable of switching between a high impact frequency mode and a high impact energy mode.

Aug 17, 2017

By Deborah A. McCombe

"There are a number of important dates that must be disclosed when a Qualified Person (QP) is preparing a technical report for securities purposes. The dates are discussed in NI43-101 and the Form of the Technical Report, NI43-101F1. •,Effective date of the technical report •,Possible revision date of the report •,Effective date of mineral resources and mineral reserves •,Date of the personal inspection (site visit) •,Signature date of the date report (execution date) •,Date of the certificate of the QP •,Date of the consent of the QP The effective date of the report is basically the cut-off date for the information that is included in the technical report. The effective date should be close to the signature date. If there is too long a period between these dates, the QP runs the risk of new material information becoming available and then the technical report would no longer be current. The effective date is disclosed on the title page of the report and on the signature page. If a technical report needs to be revised to correct problems or disclosure deficiencies identified by the regulators, the QP will normally need to include a revision date on the title page of the report to distinguish the revised version from the original version. In these circumstances, the regulators will request that the original date of the report remain on the title page and the revised date will be below it. When a technical report must be revised, the QP must resign and date the signature page of the report and provide a new certificate and consent."

Jan 1, 2003

Advances in Optical Image Analysis and Textural Classification of Iron Ore Fines

Sep 13, 2010

By J. Dean Warner

In 1984 and 1985, as part of its critical and strategic minerals studies, the Bureau of Mines investigated lode and placer tin occurrences near Rocky Mountain (Lime Peak), in east-central Alaska. The lode occurrences consist of mineralogically complex, generally fault-controlled veins, and contain an average of approximately 0.05 pct Sn, as cassiterite. Beneficiation testing of two bulk samples of the vein material produced concentrates containing 65 and 59 pct of the total tin values at grades of 0.35 and 13.9 pct, respectively. Although as much as 30 million short tons (MMst) of mineralized rock containing up to 20 MMlb Sn may be present, the grade of these occurrences is too low to be considered economic at this time. Trace amounts of cassiterite were also identified in surface samples of glacial out-wash gravels collected along North Fork Preacher Creek, which partially drains the area of tin lode deposits near Lime Peak. Low tin grades in the samples do not account for the former erosion of a large volume of lode tin mineralization from near Lime Peak; higher tin grades may be present in gravels closer to bedrock.

Jan 1, 1988

By A. G. Galaitsis

The two volumes of this report summarize the noise control work performed by BBN on a rail personnel carrier operated in coal mines. Volume I of the report - submitted November 1977 - describes the aboveground work performed to identify the noise sources, design, fabricate, and install the treatments, and evaluate the treatments through noise and vibration tests. The current volume (II)-describes the underground work conducted by BBN to determine the deterioration, if any, of the treatments when the vehicle is operated normally in a mine. There were no significant changes in the acoustical performance or mechanical integrity of the treatments at the end of a three-month period.

Jan 1, 1980

By Pertti Paavola, Hikki Rasanen

This paper describes a very exacting tunneling project. Planning and technical realization of this service and transportation tunnel was especially difficult as a matter of vibration control, because the tunnel is situated only a few meters under Maria Hospital, which is one of the most busiest hospitals in Helsinki. In this hospital there are many departments for bedpatients, research and treatment with high-tech equipment, operational surgery and a big laboratory. Besides access tunnels are situated near several apartment buildings. The functionality of the tunnel required the placement of the access tunnels to be straight towards these apartment buildings for which special care for blast induced air pressure had to be taken.

Jan 1, 1997

About 15 per cent of total electricity (400 MkW) was generated by nuclear power plants in the world (2009) and about 36 000 tons of uranium has been mined in uranium mines annually. Radioactive waste material is produced from uranium mines and nuclear power plants. The wastes must be disposed or stored safely for long-term. If they leak and/or move from disposal or storage sites due to air/groundwater flow, then a serious environmental pollution can occur. Hence, multi-layer system has been proposed and employed in order to seal off these radioactive waste materials from biosphere. Basically, bentonite is now used for establishing absorbing and sealing layers in this system. However, the amount of high quality betonite is very limited and in some cases it is hard to be obtained.On the other hand, a great deal of refuse from coal burning plants is produced every year and the amount of it is expected to be higher each year, especially in developing countries. More than half of flyash is utilised and the remaining is disposed at the disposal sites. However, the life of the disposal site is limited and it is diff cult to find a new disposal site. It is requested that the percentage of the utilisation of the flyash be increased in every field.From the above two points of view, a flyash-based barrier layer/cover system is considered in this research and this paper discusses the applicability of flyash as a content of barrier layer/cover material based on the results of a series of laboratory tests.

Dec 6, 2010

By Eric M. Hill, Daniel E. Walsh, Hsing K. Lin, John T. Hollow

The Fort Knox Mine is located in Alaska’s interior where the average ambient air temperatures range from -24°C in January to 16°C in July. The mill processes a free milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Plant slurry temperature cycles seasonally and allows for a unique opportunity to measure the impact temperature has on gold leach kinetics, carbon adsorption efficiency and cyanide destruction reactions. Mathematical models have been developed to accurately predict actual mill performance. This paper describes the development of the models and presents data that allow for a better understanding of the impact of circuit operating temperature on process efficiencies.

Jan 1, 2005

In recent years there have been many changes in mine ownership due to the on-going rationalisation towards larger mining companies. Larger companies inevitably find it hard to manage small mining operations and in many cases smaller mines do not fit corporate resource, production and profit criteria. Smaller companies are more suited to managing these medium or small scale mines and are tendering for the purchase or lease of mines that larger companies wish to dispose of. In addition to these factors there has also been a trend (especially in Western Australia) for mines to continue operating at ever increasing depths. This in turn has led to more mines operating in high stress environments and experiencing damaging seismicity. Assessing the viability of seismically active mines from a takeover or purchase point of view should involve analysing the risk profile of every aspect on mining that could be affected by adverse seismicity. This includes assessing current and alternative mining methods, mine designs, support systems, extraction sequencing, monitoring and blasting. This paper includes discussion on items that need to be assessed when considering the purchase of seismically active mines, with experience gained from some recent studies in Western Australia. In these cases it was apparent that quantification of previous seismic history on itÆs own was a totally inadequate method of assessing minewide seismic risk potential. A more holistic approach is required, taking into account all aspects of relevant data, all the minewide effects of seismic activity and all possible means of mitigating those effects.

Jan 1, 2002

By Neall. George M.

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U.S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions. A review of the literature reveals that some work has been conducted on the roof truss. 1 Gambrell and Haynes (1970) showed that the roof truss is superior to angled roofbolts installed through a header. Sheorey, Verma, and singh2 (1973) used statics to prove that the optimum angle of inclination should be greater than 450? However, to date, no systematic attempt has been made to establish design criteria. In this report, the problem was approached in three ways. First, model studies were performed to determine general trends of truss support as a function of a number of variables. This provided a better understanding of the support mechanism involved. Secondly, beam theory was employed to calculate the actual support capacity of a truss, realizing the many simplifications, assumptions, and shortcomings of this approach to such a complicated problem. Last, field testing will be utilized to test the hypotheses previously developed and provide hard data to further synthesize roof truss design criteria. Field testing has recently commenced and should be complete before mid 1977.

Jan 1, 1977

Blasts should be designed so as to maximise the percentage of charges which shoot to a free face (Le, to a pronounced rock/air interface).Free faces should be rough, parallel and reasonably near to blastholes and, very importantly, concavely·biplanar relative to the charges (see Fig. 6b). The presence of biplanar free faces requires that each charge fragments and detaches its quota of the burden rock before the detonation of:1. later-firing adjacent charges in single-row blasts, and2. dependent charges in multi-row blasts.In multi-row blasts, biplanar faces are best achieved:1. by drilling blastholes on equilateral triangular grids,2. by selecting a VI, V2 or V3 initiation sequence, and3. by using down-the-hole delays.Biplanar faces start to be created only when the conventional value of effective blasthole spacing/effective burden distance (Se/Be) increases beyond about 2.4. Values of Se/Be less than about 2.4 result in planar free faces. Where biplanar faces are created, conventional values of Se/Be are invalid and appreciably greater than real values of Se/Be.

Jan 1, 1986