Search Documents

By D. Harrington

When the word "gas"' is mentioned in connection with mining almost invariably it is inferred that the explosive gas, methane, is in mind and that the reference is to coal mining. Although methane is likely to occur in any coal mine the metal mines of the world contain by far a greater variety of gases than do the coal mines. Often the gases in metal mines are as dangerous as the gases likely to be found in coal mines, and sometimes are even more deadly. A coal mine is more likely to contain methane than a metal mine. In rare instances it may contain high percentages of nitrogen or carbon dioxide or it may be deficient in oxygen where the air is confined in a blind end or in a sealed region. Much more rarely relatively small percentages of ethane or other hydrocarbons with an odor of ether, gasoline, or kerosene, or minute percentages of hydrogen sulphide are found in a coal mine. During a coal-mine fire or explosion carbon monoxide content is likely to be high (4 per cent or more), and if the coal contains much sulphur the high fumes may contain some sulphur dioxide.

Jan 1, 1931

By Anthony E. Szczuka

Two facets of surface mining were studied: feasibility of using training simulators to increase productivity of haulage trucks, front-end loaders, and shovels; and improving the efficiency of dragline operations with a computer-aided analysis of dragline usage and the addition of an on-board operator display. Training costs per student were estimated based on current training practices. Training objectives were derived from task: analyses of haulage trucks, front-end loaders, and shovels. The cost effectiveness of training simulators was determined. A computer-aided analysis defined the critical performance parameters. An on-board operator's display is recommended to improve operator efficiency.

Jan 1, 1976

By I. M. Wolf, S. A. Usmar, L. A. Cornish

The limiting criterion in the use of stainless steel for certain forming operations such as coining is its hardness, which determines parameters such as required striking pressure, wear on dies, and integrity of pattern detail. Attention is given here to the development of ultra-soft ferritic stainless steels for coinage. In the first instance, the influence of carbon content on the striking properties of a series of commercial and experimental 17%Cr alloys was evaluated. It was found that a lower carbon content permitted the striking of relatively highly profiled and intricate patterns, provided that the hardness did not exceed 125 HV. Hardnesses as low as 115 HV were achieved in the fully annealed condition, but these alloys required high striking pressures. In a further study, three grades of experimental 14%Cr ferritic stainless steels were produced with a view to optimizing the ductility. When the residual impurities were minimized, hardness values of about 100 HV and lower were achieved. Micro-alloying additions allowed the heat-treatment response and grain size to be controlled. Excellent tensile properties, with elongations of up to 42 per cent, were achieved in the fuly annealed condition, and highly profiled patterns were produced in coining trials.

Jan 1, 1993

By D. R. Parker

"This paper canvasses emerging trends in public policy and law, which may influence the zinc industry's interest in recycling. There are forces at work beyond direct economic benefits that will drive recycling of zinc, including:• corporate determination to pursue sustainable practices and product stewardship.• public perceptions and pressure,• customer and investor demand,• workforce recruitment, and• protection and expansion of marketsIn this paper, these ""indirect"" forces are examined with particular focus on the zinc industry: It is concluded that, in today's world with an emerging precautionary approach to policy and law making, public perception concerning the environmental implications of metal products, and the need to conserve resources for future generation, a strong industry response is required."

Jan 1, 2000

By William W. Odell

Certain gas-making processes are in use in Europe, particularly in Germany, which differ radically from those in common use in America. A number of them are of particular interest because they are different. The questions naturally arise: Are any of them applicable to the making of gas in this country and, if so, with what particular type of solid fuel? It is a fact that some of them were developed with consideration of a particular set of conditions and for the utilization of solid fuels available in Germany. The latter fuels, in certain characteristics, are unlike the high-rank fuels commonly used for making gas in the United States; therefore, in attempting to evaluate the various foreign- developed processes with regard to usefulness here, one must give attention to the particular conditions that will prevail in any specified case and also the characteristics and requirements of the process and generator under considera- tion. Three of the processes that were developed and put into commercial operation in Germany, and which have some characteristics in common, are con- sidered in particular in this publication; they are: 1. Lurgi pressure gasification process. 2. Winkler process. 3. The Leuna slagging-type producer-gas process. Each of these processes requires steam and oxygen as gas-maiding fluids. For a number of years, oxygen, has been used in a relatively pure state,. along with steam, in making gas in Germany, and many of the difficulties initi-. ally encountered have been overcome. Although it appears that oxygen recovered from air was first used in this manner as a method of utilizing a byproduct in a plant that used the nitrogen complement in the manufacture of ammonia; more recently, the oxygen was made particularly for the purpose. The fuels - brown coal or lignite used in processes 1 and 2 were not suitable for use in the older and commonly used intermittent-type water-gas generators, and it was necessary, therefore, to devise a different process for gasifying them. A gas of higher heating value than producer gas, was desired, and the use of oxygen (not air) along with steam made possible the production of the desired gas without nitrogen dilution, which characterizes producer gas. Operating data presented herein are based upon observations by, members of the Technical Oil Mission at plants in Germany, on records, and on information vocally given to members of the lässion, including the author, while visiting those plants, and they are believed to be reasonably correct; however, certain hasic observations, comparisons, and conclusions are. made by the author.

Nov 1, 1947

By J. J. Forbes

The original organic act establishing the Federal Bureau of Mines in 1910 and the amended act of 1913 indicated that promotion of the health and safety of mine workers was to be ore of the chief functions4/ of the Bureau. Many of the field and laboratory studies pursued by the Bureau are designed to improve conditions under dish minors must work. As the Bureau has no legal authority to enforce safety rules, it must rely upon cooperation of employer, employees, State mining or other departments, and labor organizations for success in promulgating its finding and making recommendations. The staff of the Safety Division, which is essentially a service organization of the Bureau, is composed of 28 safety instructors, 29 engineers, 18 clersk, and 7 others engaged in promotion of an educational program in an effort to improve conditions in the mining industry. The work is directed from 14 safety stations in the United States and 1 in Alaska. The work of the personnel, of the mine safety car that operates in. the anthracite region of Pennsylvania was supervised and directed by the district engineer in charge of the Wilkes-Barre (Pa.) Safety Station.

Jan 1, 1940

By V. B. Dale

This paper is one of a series covering the mineral resources of the Nation. It briefly describes most of the known tungsten deposits of New Mexico. Most of the descriptions are from field examinations by the senior author. Reported tungsten occurrences that were not visited are listed below: Colfax County: Occurrences of ferberite in thin veins in Willow Creek near Elizabethtown.4/ Dona Ana County: Small, low-grade occurrences of scheelite near the summit of the Organ Mountains about 15 miles east of Las Cruces. Hidalgo County: Scheelite reported in the Daisy mine 7 miles southeast of Hachita. Ores are carbonates containing copper, gold, silver, and bismuth.5/

Jan 1, 1959

By Warren Howes, A. B. Campbell, W. H. Ode

"INTRODUCTION The mines in the eastern part of the now active region of the Tri-State zinc district of Missouri, Kansas, and Oklahoma have unusually acid water, which during periods of moderate or no rainfall is used in the mills to replace losses from evaporation, seepage, and tailings disposal. Its use has caused difficulties by corrosion of equipment and by interference with flotation.The growing importance of flotation, which requires good water, and the increasing troubles caused by the corrosion of the milling equipment have prompted the Mississippi Valley Experiment Station of the United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., to investigate the action of the waters on flotation and to undertake to develop means of obviating their harmful effects.The work was under the immediate direction of W. T. Schrenk, consulting chemist, United States Bureau of Mines, and professor of chemistry, Missouri School of Mines and Metallurgy, and Will H. Coghill, supervising engineer of the ore dressing section of the United States Bureau of Mines.ORIGIN OF ACID MINE WATERSRain water, carrying oxygen and carbon dioxide in solution, finds its way into the pores and crevices of the earth's crust and percolates downward through the rocks. This water and its dissolved gases exert a solvent action on many minerals, the extent of which depends upon the nature of the associated minerals.The iron sulphides are the chief sources of the 'trouble with sulphates and sulphuric acid because they oxidize so freely and contain more sulphur than is required to satisfy the iron when ferrous sulphate is formed. Galena and sphalerite may oxidize to sulphates without liberating acid. A few of the common reactions occurring in the Tri-State mine waters may be illustrated by the following equations:"

Mar 1, 1932

Since the introduction of water cooled test rings the operation of cupelling retort bullion has not alone been sImplified, but has also been the means of concentrating the bullion for the fining test in a much shorter time.The first water cooled test ring which I used was rectangular in shape, inside dimensions 5 ft. 3 in. x 2 ft. IQ in., and made of i in. mild steel plates, with a water space of 9i in. x 3t in. However, it was found that as soon as the filling commenced to wear and the litharge came in contact with the jacket, the plate was gradually affected on the lines of the wash, caused by the blast. After a while the inside steel plate went beyond the factor of safety, and was then substituted on the sides and the front of the test ring by a tin copper plate, which has stood now for the last five years without showing the least signs of wear or leakage.The test remains in use as long as the bottom is regarded as safe, and toward the end of the life of the test the litharge is allowed to work against the copper plate.

Jan 1, 1901

By J. W. Thompson

That the governor is hereby authorized to appoint a commission of seven persons, to be known as the industrial accidents commission-two of whom shall be employers of labor, two of whom shall be employees in either mines or industrial establishments of this Commonwealth, or duly accredited representatives thereof, two of whom shall be learned in the law, and one of whom shall be a person skilled and experienced in making investigations-to inquire into the causes and results of industrial accidents in the mines, mills, factories, stores, and upon the railroads, street railways, ships, wharves, and in all industrial establishments, and in all other places where men, women, and children are employed in manual labor in this Commonwealth; to study the most advanced methods for safe-guarding against these accidents; to inquire into the subject of fair compensation for those who are injured in these accidents, and for the families of those who shall be killed as a result thereof; and to study the operation and effect of the Workmen's Compensation Law of 1913. SEC. 2. The chairman of said co~mission shall be designated by the governor, and the person named on said commission as a skilled and experienced investigator shall be the secretary of the commission, The commission shall have power to employ such legal counsel and other officers and employees as it may deem necessary to properly perform its duties. SEC. 3. The secretary of said commission shall receive an annual salary of $2,400 and his actual necessary expenses; and the other members of the commission shall receive no compensation for their services, but shall be allowed their actual traveling and other necessary expenses. The salaries of any other persons employed by the commission shall be fixed by it.

Jan 1, 1920

By V. H. Gottschalk

Sponge iron is a product resulting from the reduction of an iron oxide below the temperature at which the product melts. Commercial grades usually contain 80 to 95 percent metallic iron, 2 to 5 percent unreduced iron oxide, and an amount of siliceous gangue material depending on the pur.ity of the are used for reduction. The reducing agent may be gaseous or solid, and a large variety of procedures have been proposed for bringing the reducing agent into reaction with the iron oxide. Of the proposed procedures, the one that has the distinction of having been in continuous commercial operation for the longest time, from 1911 to date, was developed at a ceramic plant in Hoeganaes, Sweden, and yields? a product that has an enviable reputation as furnace feed wherever special, high-quality steels are made.

Jan 1, 1948

By M. Ataee-pour, S. E. Jalali

So far, a large number of algorithms have been developed for the optimization of pit limits, most of which follow deterministic rules. In this paper, a new algorithm is introduced, which follows a probabilistic logic using the Markov chain process. The algorithm is implemented on a transition matrix that corresponds to the 2D conventional economic block model of the mining area. The probability of mining a block is proportional to the desirability it may provide. Applying this algorithm, the probability of mining each block is obtained, and finally, the optimum pit limits are defined as the pit, which provides the highest probability of mining. In order to validate the proposed model, a numerical example is given and the results of the algorithm are compared to those of a dynamic programming algorithm. A 2D analysis of the problem is discussed in this paper. Although dealing with 3D problems requires larger size matrices, the optimization method is the same and the algorithm does not need any smoothing.

Jan 1, 2006

By Dave Kay, Young-Suk Song

To meet the needs of South Korea's rapidly expanding economy, a large number of infrastructure projects are under way to improve transportation efficiency within the nation. These projects include high-speed rail links between major population centres and improvements to the road network. Being densely populated and geographically mountainous, infrastructure development in Korea requires a significant amount of tunnelling. Owing to the predominantly hard granitic nature of rock, drill and blast is the preferred method of tunnel advance. The Korean tunneller, however, faces the same pressures as those of his international counterpart in that both cost and production targets need to be achieved while meeting expectations of both community and regulator.

Jan 1, 2005

By C. A. Heiland

THIS year's review of geophysical activities has a somewhat different complexion than usual. With the ending of the war, the time seems opportune to supplement the customary report on operations and discoveries in oil and mine exploration by a review out-lining the contributions of geophysicists to the. war effort. To give as much space as possible to the latter, presented as Part 2, some of the usual review features have been omitted from the statistical section, given as Part 1 immediately following.

Jan 1, 1946

By James C. Barker

The analytical variability encountered when sampling for platinum-group metals (PGM) was statistically evaluated during a 1983 study by the Bureau of Mines and the University of Alaska. Sampling procedures were designed to systematically incorporate commonly used reconnaissance exploration techniques under actual field conditions. Analytical variability was evaluated at each procedural step. Analytical data from each sample from a single deposit grouped relatively well around the calculated mean for that deposit. Standard deviations did not exceed 43 pct of the mean for any of the deposits; more commonly, the deviation was about 25 pct. Statistical treatment of the data by analysis of variance indicated the most important source of error is selection of the sample site. Two or more replicate samples appear necessary to adequately quantify the PGM content. Secondly, significant variation occurs during preparation of a pulverized split for fire assay. The optimum sample size was in the 11-lb range; larger samples did not appreciably reduce variability. Smaller samples generally indicated a higher degree of variability. Evaluation of the sample method suggested the common grab sample, if carefully taken, is a useful indicator of the general range of PGM concentration but potentially includes a considerable margin of error.

Jan 1, 1985

By Norman L. Wimmler

Active placer mining in Alaska began near Juneau in 1880, but the first gold rush did not start until 1896; then the discovery of the Klondike brought gold seekers from all parts of the world. A few of the newcomers were experienced miners, but the majority knew nothing whatever of placer mining. Even those who were placer miners of much experience found entirely new conditions, notably frozen ground, that presented many difficult problems. As a result, numerous methods of mining and of thawing frozen ground were tried. From these trials the practice described in this bulletin has been developed. All known placer fields in Alaska have been mined to some extent, and some have been virtually exhausted. In most districts, however, there remain large quantities of low-grade gravel and also some small isolated areas of comparatively rich gravels which could not be successfully mined because of adverse physical conditions. These districts are now the scene of most placer mining, including dredging, hydraulicking, drifting, mechanical methods of open-cut mining, and ground sluicing (or booming) followed by " shoveling-in."

Jan 1, 1927

By D. B. RUSHhIORE

I. INTRODUCTION. OF primary importance in mine-installations is the hoist, which has a very direct bearing on the successful operation of a mine. Conditions vary greatly with different mines, and especially in different localities. Such factors as depth, incline, the number of levels, permissible or desirable speeds, conditions of ore, etc., are always more or less special in each case. Veins of ore are never exactly duplicated, and the nature of the ground through which shafts are sunk may considerably modify permissible values. As mining-laws are made by the different States, they necessarily vary somewhat, and, even when not fully observed, they introduce factors which qualify the conditions of hoisting men and ore. The amount of timbering required is often of importance as relating to hoisting-conditions. Methods of loading ore affect the time required, as also does the question of the use of cars or skips. Safety-precautions must be very carefully considered, and the number of men in each mine, the number of compartments, and often the method of removing water from the mine, must. have careful consideration. While a general discussion of the subject. of hoisting is possible, most cases are entirely special, and can be considered only in connection with the peculiar conditions pertaining to that particular installation. The cost of installation of the hoisting-plant may be an appreciable amount, while the cost of raising the ore may be but a small part of the total operating-charge. In many cases, however, the output of the mine is limited by the capacity of the hoist, and the latter thus becomes of the first importance. * Presented also, by mutual agreement, at the meeting of the American Institute of Electrical Engineers, New York, N. Y., Mar. 11, 1910.

May 1, 1910

By C. O. Hawk

A PART of the Bureau of Mines effort to improve the conversion of coal to liquid fuels, batch autoclave tests were made on the hydrogenation of bituminous coal by a dry method, which featured charging the autoclave with dry ingredients only-coal, catalyst, and hydrogen. This innovation, which omitted the liquid vehicle used in earlier work, limited the products to those made from the coal charged. The effects of the common process variables (catalyst, hydrogen pressure, temperature, and residence time) were studied. Tin catalysts showed the highest activity in the widest variety of forms and were the easiest to disperse; dry mixing in the autoclave during the heating-up period usually sufficed. Ammonium molybdate, on the other hand, was inactive when dry mixed, but it compared favorably with the best catalysts known when applied by impregnating the coal with a solution of a molybdenum compound. As a group, metal naphthenates were the most effective; in fact, molybdenum naphthenate was the most active catalyst the Bureau tests disclosed. One-hundredth of a percent of molybdenum in this form (calculated as the metal in weight-percent of maf coal) induced 90-percent conversion of coal. However, because of their high cost, naphthenates have as yet only technical significance in coal hydrogenation. Long residence time and high reaction temperatures tend to increase the amount of thermal decomposition products formed (light hydrocarbon gases and/or char). High hydrogen pressure favors the production of liquids.

Jan 1, 1965

By H. W. Gillett, E. L. Mack

Prior to 1911 the literature on melting brass by electricity consisted entirely-save for some suggestions made in patent literature but not actually worked out-of a few observations by farseeing men ' on the theoretical advantages of melting brass and other nonferrous alloys in electric furnaces. Roeber was the first to see and clearly state the possible advantages of the electric furnace in brass melting. The same factors tha.t make it desirable to manufacture special steels in the electric furnace rather than in crucibles, he declared, apply to brass as well. He pointed out the possibility of using larger melting units, of eliminating crucible cost, of readily controlling the purity of the product. and of nearly eliminating the loss of zinc. "The replacement of the • old crucible process is sure to come," he said; "perhaps it will come in two years, but it will, necessarily, in ten years .... The inevitable advance along this industrial line will have great influence in the metal world and will also provide, in large cities, a new kind of load for the central station." The years 1905 to 1910 may be termed the purely theoretical period of the development of the electric brass furnace, though the Conley furnace was tried out e:xperimenta.lly about 1910 and a few heats were made in an induction furnace. 2 In December, 1911, the American Chemical Society held a symposium on mineral wastes, at which Bassett s discussed the zinc· losses that attend making brass in fuel-fired furnaces.

Jan 1, 1922

By S Dunham

A cross-discipline approach combining geology, metallurgy and mine planning, geometallurgy is seen as the next logical advance in improving the design and operation of mining businesses. This rapidly evolving field is focused on realising the value that has often been lost in the chasms between the aforementioned technical silos. When successful, the geometallurgical approach promises the ability to tailor mining and mineral processing development and operational options more closely to the characteristics of the resource with resulting lower costs (both capital and operating), improved recoveries and fewer project failures.As with any technological (or managerial) change, there will be side effects from the success of the geometallurgical approach that will impact areas beyond obvious linkages between geology and processing. Some of these effects have the potential to be beneficial to the resource industry and society in general. Beyond the basic geometallurgical promise of closer alignment between processing design/strategy and the multivariate 3D spatial characteristics of the mineralisation, this paper discusses the broader implications and ramifications of the emergent geometallurgical approach: enhancing exploration and discovery; improving project development success; achieving sustainability in an industry working with non-renewable resources; in a world of increasingly hard won license to operate, improving the management of potentially harmful by-products and waste materials (with knock on effects for proactive management of closure issues); smarter approaches to energy management and thus optimisation of projects with respect to carbon footprint; and potential to re-value assets and thus realise a strategic advantage in the area of acquisitions, divestments, mergers and take overs. The authors strongly believe that companies that actively engage with the above issues (and ensure that technical efforts in the area of geometallurgy are not isolated from the larger value chain activities of the firm) will be able to exploit the opportunities that consequentially arise. These early adopters will gain first mover advantages. Firms taking the broad view of geometallurgy will have an opportunity to maximise stakeholder value and win greater success than their less insightful competitors.

Sep 5, 2011