Search Documents

By H. E. Powell

A laboratory investigation was conducted by the Bureau of Mines to study the magnetic characteristics and to measure the magnetic susceptibility of the mineral siderite. All susceptibility measurements were made by the method of Gouy on powdered samples and at room temperature. Specific susceptibilities of samples from 15 different locations, domestic and foreign, were determined. Values ranged from 66 to 103 (10-6) cgs electromagnetic units. The relation of susceptibility to mineral composition is discussed in this report. The specific susceptibilities of 76 minerals are tabulated in an appendix.

Jan 1, 1963

By Rudolf E. Greuer

This report contains the practical application of a computer program for the simulation of ventilation systems under the influence of mine fires and other emergencies on five hardrock mines. The introduction describes the need for such a program, its basic features, and the range of its applicability which is mainly a function of the available ventilation data. The second chapter discusses program modifications, whose necessity or desirability was, during the application, discovered. The following five chapters, which comprise the major portion of the report, give the detailed description of the program application on the five mines. For every one of the selected mines, the ventilation system, the source of the used ventilation data and their preparation for computer simulations are outlined. Based on data for the airflow distribution solely, fumes concentrations in the mines are calculated for several assumed fire locations. Based on data for airflow and pressure distributions, ventilation disturbances caused by fires as well as the resulting fumes concentrations and temperatures are determined. The consequences for escape routes and the possible means to keep them free of fumes are discussed. To investigate the capabilities of the program, other contaminant sources and other potentially dangerous ventilation factors, like fan failures and changed surface temperatures, are simulated also. The results of the calculations have been entered into ventilation plans which makes them easier to scrutinize. All significant computer printouts have been attached.

Jan 1, 1981

By G. Beckstead, L. F. Sawatsky, R. Nutbrown, D. Long, G. Gould

"This paper presents a case study for optimizing water management at Gregg River Coal Mine located near Hinton, Alberta. The optimization study was derived based on a review and assessment of existing management practices and plans for future operation and final reclamation. A proactive water management strategy was developed to assist mine staff in adopting a rational, environmentally sound, and economical approach to water management. A plan was developed to provide for safe operation, self-sustaining operation, low maintenance, minimum negative environmental impacts, and anticipation of future needs for existing and future operations. A plan for final reclamation drainage was developed including establishment of effective, sustainable, and maintenance-free water management systems. The study demonstrated the importance and benefits of a proactive approach for integrated mine water management. This approach is recommended for other similar mine operations because it will improve environmental compliance and reduce costs of water management. IntroductionGregg River Resources Ltd. (GRRL) operates an open pit coal mine on the eastern slopes of the Rocky Mountains, located about 45 km south of Hinton, Alberta. GRRL opened the mine in 1982 and expects to continue operations after Year 2000. GRRL has progressively reclaimed the disturbed area and expects to complete mine-land reclamation shortly after mining in the area is complete. The existing disturbed area and reclaimed area covers approximately 9.5 km2 and will expand to about 10.5 km2 upon mine closure.Like other coal mines in the mountainous areas of Alberta and British Columbia, the GRRL coal mine is subject to highly variable temperatures and moisture conditions. Average monthly precipitation varies from a low of 12.6 mm in January to a high of 113.0 mm in August, based on the precipitation record at the mine site since 1982. Despite the relatively high rainfall during the spring and summer months, excess water problems during rainfall events are quickly replaced by water deficit conditions during periodic droughts. Surface runoff varies from near zero in the winter to a mean annual monthly maximum of 78 mm during the month of June. The mean annual surface water yield is 345 mm."

Jan 1, 1997

By William H. Langer

I spent 41 years as a geologist with the US Geological Survey (USGS) conducting geologic studies and preparing peer reviewed maps and reports describing the results of those studies. Since retiring from the USGS in 2011, I have been a consultant specializing in aggregates and other industrial minerals. Consequently, I have had the opportunity and pleasure to apply the information contained in those kinds of geologic maps and reports to real-life situations. About half of my consulting is performing due diligence for mineral resource evaluations of one type or another where resource information has been provided by the property owner. Many of those jobs necessitate that I conduct desktop studies followed by field work. I then use my information to review and comment on the written reports of others; reports variably referred to as geologic reports, resource studies, reserve analyses, and so forth. While there are many well written reports addressing geologic resource issues, I was surprised to see that there are also a significant number of so-called geologic reports that only pay cursory attention to geology. Unfortunately, that lack of rigorous geologic investigation commonly leads to erroneous conclusions. This paper addresses three such reports covering concrete sand, metallurgical gravel, and proppants (frac sand). Although all three examples are located in the Gulf Coastal Plain Province, I do not reveal the exact location of any of the properties for purposes of confidentiality. Furthermore, I have generalized the site descriptions and illustrations. However, all the descriptions faithfully define the geologic situation.

Feb 1, 2024

By Jr. Brinkley

For a theoretical description of power plants that derive their energy from the combustion of a fuel, it is necessary to solve, to an appropriate degree of precision, a hydrodynamic problem that requires for its solution a knowledge of the thermodynamic properties of the working fluid com-posed of the products of the combustion reaction. It is usually a good approximation to assume that the properties of the combustion gas are determined by the conditions of thermal equilibrium, and it is thus possible to employ the methods of Classical thermodynamics for their computation. The thermodynamic properties of fuel gases also are of considerable importance, as they form the basis for the design of appropriate means for their effective utilization. The specification of the operating conditions to produce a gas for use as an intermediate in a chemical process, such as the synthesis of liquid fuels, may be based upon a study of the variation of the composition of the synthesis gas with changes in the various process variables. Although there exists a large number of important scientific and technical applications of the data that can be obtained from the systematic determination of the thermodynamic properties of combustion gases, such application has been greatly handicapped by the extremely tedious and time-consuming computational methods required. The development of large-scale automatic computational equipment makes feasible the initiation of a systematic program for the determination of the thermodynamic properties of combustion gases and for the application of such data to specific problems of scientific and technical importance. As a part of its program of basic research in flame and combustion phenomena, the Explosives and Physical Sciences Division of the Bureau of Mines is engaged in such a program. The present communication is designed to introduce a series of reports presenting the results of this program.

Jan 1, 1951

By WILLIAM COUPER

THE completion of the excavation of the tunnels through Bergen Hill for the extension of the Pennsylvania Railroad into New York City, together with the fact that the excavation for the rest of the tunnel-line has been practically completed for some time past, arouses sufficient interest to justify a description of the engineering- and contracting-work, and the organization by which it has been accomplished. The finishing of the excavation is a long step towards the completion of the entire tunnel-project. It will be interesting to the members of the Institute, who last spring were taken through a great part of this work, to know that by the excavation now completed it is possible to walk by tunnel from a, point near Sunnyside yard, Long Island, east of the 34th Street ferry, to the central passenger station site in the City of New York, and thence by tunnel to the Hackensack meadows, and by an embankment constructed across these meadows to Newark, N. J. This New York tunnel extension is being constructed as a part of the Pennsylvania Railroad system by the Pennsylvania Tunnel & Terminal R. R. Co., a corporation of the States of New Jersey and New York. It extends from a point near Newark, N. J., to the Sunnyside yard, Long Island, as indicated on the accompanying plan.

Jan 7, 1908

By Walter D. Holland

This instructors guide is intended for use in a course which teaches metal and non-metal mine inspectors to perform surveys for inhalation contaminants in above ground metal and nonmetal mine work areas. The handbook entitled "Handbook for Surveys of Inhalation Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas? is used as a manual during the course. The manual contains a survey check list, rules for determining if sampling is required, a list of most frequently encountered contaminants, a list of candidate contaminants and their sampling conditions, and a description of control procedures and devices. There are several experiments in this guidebook which the trainees perform to acquaint them with the sampling systems.

Jan 1, 2011

By L. J. Terrill

Lateral displacement in the immediate roof beam at the Waste Isolation Pilot Plant (WIPP) is a significant factor in assessment of excavation performance for the design of ground control systems. Information on roof beam lateral displacement, expansion, fracture formation, as well as excavation convergence, is gathered using a variety of manually and remotely read instruments. Visual observations are also used when possible. This paper describes the methods used to measure lateral displacement, or offset, at the WIPP. Offset magnitudes are determined by the degree of occlusion in drillholes that intersect the offset plane. The Borehole Lateral Displacement Sensor (BLDS) was developed for installation at WIPP to monitor offset at a high degree of accuracy at a short reading frequency. Offset measurements have historically been obtained by visual estimation of borehole occlusion. Use of the BLDS will enable relationships between time dependent roof beam lateral displacement and expansion to be established in much shorter periods than is possible using visual observations. The instrument will also allow remote monitoring of roof beam displacement in areas where visual estimations are not possible. Continued monitoring of roof beam displacement, convergence, and expansion, is integral to timely and pertinent assessments of WIPP excavation performance.

Jan 1, 1996

In 2005, CANMET-MMSL used its pool of expertise in ground control, open pit and underground mine engineering, mineral processing, information technology and applied mineralogy to launch a mine-to-mill research project. The objective of the project was to optimize the distribution of rock breakage energy among blasting, crushing and grinding activities, thereby maximizing the efficiency of energy utilization within comminution processes. Tests were designed to demonstrate that this approach could reduce energy consumption, thus contributing to the reduction of green house gas (GHG) production in the Canadian mining industry. The project was accomplished in collaboration with DynoConsult and Dyno Nobel Canada Inc., a world leader in commercial explosives. Data analysis from 12 blasts (six with electronic and six with pyrotechnic detonators) in three different geological formations of a quarry (soft, medium and hard rock) shows that electronic blasting technology increases rock fragmentation by 15% (in hard rock) to 20% (in soft rock). A more uniform rock fragment size distribution is also obtained. The impact of the improved quality blast product on downstream processes of the quarry is a productivity increase of 5% in rock excavation and transportation, an energy reduction of 10% at the primary crusher and an increase of 15% of the primary crusher throughput. Extended to the Canadian mining industry, such results would represent a GHG emission reduction of about 0.05 Mt/y. A soft-sensor prototype, based on primary crusher data (i.e., energy consumption, throughput, feed and product size distribution) and a simplified computerized process model, was developed for on-line measurement of the rock operating work index. Additionally, 385 rock samples and specimens were collected and prepared to determine the tensile and compressive strength of the rock material, to evaluate the aggregate crushing work index and to examine the development of micro- and macro-fractures by means of binocular and SEM microscopy. Blast-induced rock damage was evaluated at the end of the laboratory-testing program. Even though a reduction of rock hardness of around 30% was observed after blasting, the impact of the blasting method (i.e., use of electronic or pyrotechnic detonators) on the induced rock damage could not be observed. It is either absent or not perceptible with the accuracy of the measuring techniques and the number of samples analyzed.

Jan 1, 2008

By Adrian Brown

Pilot Hole ?X? was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine will be drilled. Five permeability tests were performed at various stratigraphic levels within this hole. The test method used was that of pumping fluids out of the hole for three hours, using the air lift method, followed by a three-hour period where the recharge was observed. Transmissivity and permeability results were determined from these test data. The test procedure used is described and supporting data for the hydrologic tests are provided.

Jan 1, 1977

By T. L. McCall

CHANGES in mining practices have evolved so quietly and unobtrusively that perhaps we scarcely appreciate how truly startling these changes are unless we cast our minds back so as to compare the past with the present. Such retrospection is, indeed, necessary when attempting to forecast the future, for it is only by carefully reviewing the past that we can hope to obtain an indication of what the future may hold in store. In this instance, it is not necessary to delve into the very early history of . coal mining, as our purpose will be served if the last three or four decades are reviewed, a period that is still fresh within the memory of many of us. These earlier days might be termed the selective period of mining, for at that time the coal resources of the world had not been tapped to anything like the extent they are at present and this condition enabled the owners and operators to exercise selective powers and only mine such seams of coal as could be most easily reached an worked at the lowest possible cost and which, at the same time, would suit the requirements of the market. Carrying this thought of selective mining still further, the miner, who was then an artisan skilled in all the branches of his calling, was able to select or discard such parts of the seam he was working that the co al sent out of the mine was acceptable to the consumer with just the barest minimum of preparation. Compare these conditions with the? conditions prevailing today, when coal seams of medium height, good quality, and readily accessible have been largely depleted and the operator has been compelled either to carry on his operations under much greater depths of cover where the coal is more costly to win, or else to work seams of lesser height or of poorer quality.

Jan 1, 1938

By R. Kanniganti

The primary problems of pillar design in seams subject to interaction are due not only to difficulties in predicting loading, but also to the often unsymmetrical nature of the stress fields. The effects of uneven stress fields on failure patterns within a pillar were studied wing a two dimensional finite element method. Lower seams, including ultra- close mining situations were evaluated considering conventional pillars. Pillar case study data for under mining were analyzed to determine if empirical trends in stable pillar sizing could be derived. Recommendations for multi-seam pillar design are made, based on anticipated loading conditions within a pressure bulb. Applications of the research results are demonstrated using case studies

Jan 1, 1995

By F. W. DeVries, O. B. Mathre

Addition of Kastone® peroxygen compound and formaldehyde to cyanide gold extraction process effluents, containing at least 5 mg soluble copper per liter, will oxidize acid-dissociable cyanide to levels less than 0.2 mg per liter, without appreciable oxidation of thiocyanate. Most of the copper precipitates and is removed by filtration of the treated solutions. The treatment can be completed in less than 2 hours when the excess of hydrogen peroxide over the cyanide is about 75-100 mg per liter. The excess hydrogen peroxide destroys residual formaldehyde and then is catalytically decomposed by the copper-containing solids that separate, so it will not interfere with subsequent operation. A pilot plant using this technology has been operated for more than four months at rates from 1-2 gpm. Clear, filtered effluent containing less than 0.2 mg acid-dissociable cyanide per liter has been produced.

Jan 1, 1981

By R. J. Allan

"CANADA HAS A GREATER LAKE AREA than any other country. Discountin the Great Lakes, this fresh-water area, mainly in the Canadian Shield, is listed as approximately 300,000 sq. mi. Densities of lakes range up to 7,500 in a 5,294-sq. mi. area of the Shield, southwest of Reindeer Lake, Saskatchewan. Five areas chosen randomly from the Shield (Figure 1) contained sufficient lakes to provide samples at a density of at least one per 10 sq. mi. Regional geochemical surveys in the Appalachian area (Nova Scotia, Boyle et al., 1958; New Brunswick, Boyle et al., 1966) and in the Cordilleran area (Yukon, Gleeson, 1965) of Canada and in many other areas of the world have relied heavily on analyses of stream sediments. These surveys show that sampling of material related to the drainage system reflects the over-all trace element content of the rocks and surficial deposits in the drainage basin. In the Shield, the classic types of dendritic (and other) stream systems found elsewhere in the world are very rare. However, impeded and disorganized stream systems that abound with lakes can provide the exploration geochemist with an ideal composite drainage system sample in the form of lake sediment. This paper attempts to demonstrate the feasibility of, and review the theory and problems involved in, the use of lake sediment as a regional geochemical exploration medium. Most of the references to field examples are taken from a regional survey using lake bottom sediment as the sample medium over 1,500 sq. mi of the Coppermine basalt group and adjacent rocks (Figure 2). During this regional survey, detailed sampling of several lakes was carried out and the results are referred to at appropriate places in the text."

Jan 1, 1971

By Larry Schneider

Are you one of the thousands of hunters, fisherman, or hikers who purchased handheld GPS systems over the past several years and then been disappointed in their accuracy and performance. Or maybe you are one of the hundreds of blasters who have attempted to use GPS as a method for locating the exact position of their blast and measure distances from the blast to nearby structures. If so, you may have found that the accuracy of the handheld GPS systems left much to be desired. It may be time to get the units back out of storage and give them another try. As of midnight, May 1, 2000, the federal government has turned off the “error” built into the system known as “selective availability.” Here is a brief explanation of what that means in a question and answer format.

Jan 1, 2001

By George S. Rice

"The emission of hydrocarbon gases from coal beds and contiguous strata causes many accidents in coal—mine workings, the number of fatalities so caused being second only to those due to falls of roof. Gases tend to increase in amount with depth of coal mining, hence the danger of explosion is increased with depth. The pressure of the gas in virgin—coal areas at a distance from mine workings likewise tends to increase with depth from the surface, probably due to corresponding increase in hydraulic head and possibly, when the gas is held in nonporous formations, to greater ground pressure. The rise in gas pressure with depth under usual conditions is shown in wells drilled from the surface and in some coal fields in drill holes into the face of workings; however, under normal conditions of coal formation gas does not issue into workings under high pressure because the coal and adjacent strata have many bedding and joint planes which allow the gas to escape freely at the face of the workings. The rare occurrence of instantaneous outbursts of gas, with violent effects referred to later, constitute the exception.Variations of volume and pressure of fire-damp or methane found in different coal beds by wells at a distance from mine workings, are analogous to variations in volume and pressure of natural gas found in different gas and oil sands, although in general the pressure tends to increase with the depth. Sometimes, however, in tight sands higher in the formation the pressure of gas therein is abnormally high, and on drilling the well deeper gas in the lower strata may be found at lower pressure."

Jun 1, 1934

By Erik Melchiorre, M. Katherine Crombie, Dante Lauretta, Chris Gholson

Rich Hill, also known as Weaver District No. 2, is among the most productive placer gold locations in Arizona. Located near Congress, AZ (Fig. 1), this district hosted major placer rushes in the 1860s and1930s. Those rushes were followed by an electronic metal detecting rush that started in the 1980s and continues today. Thousands of ounces of gold have been produced by these modern amateur and professional metal detectorists. Many of them see more gold in an afternoon than Nevada mine workers will ever see outside of the mill. Rich Hill discovery Inspired northeastward by Spanish legends, a party of 10 men left Yuma, AZ on April 1, 1863. Included in the group were Pauline Weaver (Fig. 2), Henry Wickenburg and Abraham Peeples. Wickenburg left the group near the Hassayampa River and discovered the Vulture deposit. The rest of the group arrived at the base of Rich Hill in late May. While drying antelope meat on the first day, a few of the men prospected a nearby creek bed and immediately found gold. In a couple of hours they picked up more than 2.8 kg (90 oz) of gold. The next day, four members of the party went searching for their horses and returned with news that a nearby hilltop was literally graveled with nuggets.

Jan 1, 2003

By A-A. Bogno, Ch. -A. Gandin, A. Maitre, H. Henein

Most metallic materials are produced from their liquid state. In order to control the properties of industrial products, it is very important to understand their solidification path and the resulting microstructures which can be significantly affected by melt undercooling. High undercooling results in rapid solidification and a refined microstructure with minimal microsegregation. This paper reports on the analysis of rapidly solidified Al-Cu droplets obtained by a single fluid atomization process, Impulse Atomization. A quantitative analysis by Rietveld refinement method of the Neutrons Diffraction data was carried out to determine the fraction of the intermetallic Al2Cu. Knowing the fraction of Al2Cu, the eutectic fractions and corresponding dendritic and eutectic undercoolings were estimated using the metastable extensions of solidus and liquidus lines of the Al-Cu system calculated by Thermo-Calc. In addition to this work, a model of microsegregation coupled with ThermoCalc software via TQ (application programming interface of ThermoCalc) and the Wang-Beckerman model for dendritic growth velocities has been developed for binary alloys. This has led to the development of a phenomenological relationship between primary phase undercooling and initial growth velocity. A comparison of estimated primary undercoolings using a coarsening model with the adiabatic undercoolings for each alloy composition has confirmed that solidification occurs under adiabatic conditions during recalescence.

Jan 1, 2014

By Steven D. Sandbrook

A man by the name of Louis Binstock once said, “Too often the shortcut, the line of least resistance, is responsible for evanescent and unsatisfactory success.”

Jan 1, 2015

By Dipak C. Talapatra

This report describes the development of guidelines for design, inspection and maintenance of automatic couplers. In order to devise the guidelines, performance requirements for automatic couplers were carefully established. This was clone through a comprehensive survey of coupler manufacturers and extensive observation of automatic couplers in service in a broad spectrum of mines. The capability of the couplers to withstand the demands of the mining environment in terms of strength characteristics, gathering range, curve negotiability, and other factors were all carefully evaluated. An analysis of coupler related accidents for the years 1972-1976 was carried out to provide information on the safety and reliability of existing automatic couplers. This formed an important input to the development of the guidelines. It is expected that these guidelines will he useful to coupler manufacturers for establishing designs for improved automatic couplers, and to mine operators for maintaining their couplers in a safe and good operating condition throughout their expected lifetimes. This report is in two volumes: Volume l - Technical Report Volume 2 - Design, Inspection, and Maintenance Manual

Jan 1, 1977