Search Documents

By N. M. Safaya

Moderate to acute deficiency of plant available phosphorus is very common in western coal mine spoils and topsoils. Although some of the spoils are known to contain seemingly adequate amounts of total phosphorus, the plant available phosphorus is so low that it constitutes a serious plant growth limiting factor in the mined lands. For the revegetation of these spoils, the use of species, varieties and ecotypes exhibiting greater efficiency for P uptake and utilization, or conversely, lesser susceptibility to P deficiency would be highly desirable. To identify such plants, quick and adequate methods of screening germplasm should he available. In the present growth chamber study several plant species were screened using continuous flow culture and spoil culture systems to provide information on their relative susceptibility. In flow cultures, P was maintained at 0.25, 2.5, and 25 moles; while in spoil cultures it was applied at 0, 25, and 75µg/g to a P-deficient spoil. Phosphorus deficiency symptoms appeared in alfalfa cultivars, birdsfoot trefoil, emerald crownvetch and yellow sweetclover within 7-10 days upon transfer of their seedlings to U.25 or 2.5 µM P solutions. Burning bush and Russian thistle, found abundantly as pioneering species on mine spoils, showed no deficiency symptoms; their shoot dry matter yield in the 0.25µM P treatment was 24% and 36%, respectively of their maximum yield obtained with 25 µM P. However, the percent increase in the dry matter yield of legumes with 0.25 µM P ranged from 7-13% over their maximum yield. With the increase in solution P concentration, the root dry weight ratio in the legumes increased from an average of 0.22 to 0.43, while in the weeds from 0.14 to 0.30. The low susceptibility of Russian thistle to P deficiency was also demonstrated in the spoil culture experiment. Legumes showed greater response to P-fertilization on the spoil than did the two weeds. With increasing concentrations of P in the solution, the root weight ratio of all the species decreased. At 25 µM P, weeds invested only 14% of their total dry matter yield in the root fraction, where as legumes and grasses invested as much as 24% and 33% respectively. Weedy species averaged higher P concentrations than the legumes and grasses. The mean P concentrations of alfalfa cultivars were the lowest among legumes. In general, P concentrations increased with the increase in P supply. In the flow culture system, P supply increased the Ca levels of legumes. The mean Mn concentrations were highest in the weedy species. The increases in P supply decreased Zn levels in all of the species. File effects of P fertilization on the tissue concentrations of Mn and Zn in spoil culture were similar to that of flow culture system. From this preliminary study, it may be concluded that the continuous flow culture system is efficient in rapid screening of a large number of species under controlled conditions for their efficiency in adapting to mineral stresses.

Jan 1, 1982

By Jessica Barber

Problem ? Mining operations consistently need equipment that is available, and able to perform to its maximum potential ? The most difficult part of a Maintenance Manager?s job is often a lack of knowledge on how long their equipment has to last ? The short term view can lead to interim fixes that accumulate into larger problems ? It is always difficult to justify major overhauls and upgrades when there is pressure to meet mine plan production targets

May 1, 2008

By William E. Souder

The behavioral accident simulator (BAS) is a computer program that can be used to simulate accident situations. It demonstrates how the potential to have an accident grows or diminishes as a result of changes in various environmental, organizational, and behavioral factors. It calculates the number of fatalities that may result from various conditions and graphically displays these data. The BAS is useful for studying systems of accident causes, for demonstrating the various ways to diminish fatalities, and for training employees. This Bureau of Mines report provides the detailed instructions needed to use the BAS.

Jan 1, 1988

By Tapio Leskinen

"l. IntroductionA reliable sampling system is the basis for an on-stream analyzer. This was realized in Outokumpu company when the development work of the Courier 300 On-Stream X-ray analysis system was started. Because Outokumpu Oy is a mining and mineral processing company, its engineers have been able to thoroughly test sampler prototypes in actual operating situations. The sampler development has been going for several years in close co-operation between company's concentrators, the Institute of Physics and the Instrument Division of Outokumpu Oy. The most active part of the work was done between 1969- 1972. Besides the reliable operation of a sampler special attention was paid to the representatively of the samples taken by the samplers. 2. The Courier 300 Sampling SystemThe sampling system comprises up to fourteen sampling circuits in one Courier analysis system. Each circuit consists of the following components:1. Primary sampler 2. Secondary sampler 3. Cleaner screen 4. Feeding tank5. Sample cell6. Timer-controlled sampler7. Pumps, sumps and pipesSecondary samplers, cleaner screen and feeding tanks are included in the secondary sct1npling system. The sample cells are located in the spectrometer cabinet of the analyzer."

Jan 1, 1976

By Ray H. S, Galgali R. K

It is well accepted that the blast furnace will continue as the main route for iron-making for many more years. However, its limitations have motivated researchers to look for alternative routes, particularly, those where non-coking coal is used for liquid iron production. Smelting reduction (SR), where coal and oxygen are used to produce liquid iron and power is now receiving serious attention. Several smelting reduction reactors are now operating in pilot plant scale and one or two have reached commercial status.

Jan 1, 1999

By W. R. Donaghue, R. L. Robinson, C. Scott

Whilst spontaneous combustion has never been considered a major problem in south Durham, certain collieries in the area have a history of heatings and precautions are essential. Three collieries are affected - Shotton, Vane Tempest and Seaham - and in the case of the last two, there are huge areas of high quality coal to work under conditions where spontaneous combustion is a real hazard. The seam being extracted has an immediate roof in goaf left by the incomplete extraction of a contiguous seam worked before the turn of the century. The presence of residual coal stocks and old roadways and cavities adds to the difficulty of preventing unwanted air movement. The main preventive measures adopted are the construction of airtight gateside packs and the use of sprayed surface coatings in the gate. Sampling systems and sampling points are described and, in particular the field of continuous monitoring from the surface is examined. The resulting possibility of a quantitative as well as qualitative assessment of the preventative measures required is discussed.

May 23, 1905

Solid. dense, air-cooled slag can fulfil most, if not all, the functions of natural stone for civil engineering purposes. The value of pumice, also, has long been appreciated, and processes for the manufacture of similar synthetic material for light-weight concretes and insulating fills have been developed in past years.Foamed slag is, in effect, blast furnace pumice and is often referred to on the European continent as metallurgical pumice. It is made by the treatment of molten blast furnace slags with a critical quantity of water during which process the slag cools and expands into a sponge-like mass. The connection between foamed slag and air-cooled slag is also considered and a basis for density control given.All blast furnace slag cannot be foamed to give a product which would comply with B.S.S.877; 1939 Foamed Blast Furnace Slag. A large proportion of the total output of molten slag lacks the necessary inherent properties. This investigation attempts to discover the conditions necessary for the production of foamed slag capable of meeting the British specification.EARLIER WORKIt was generally accepted (Parker, 1951; Gallai-Hatchard, 1955) that the spongy structure of foamed slag was caused mechanically by steam trapped in the slag when it was poured into water. It was assumed that slags which would not foam would not trap steam, because their viscosities and surface tensions were unsatisfactory, on account of temperature and/or composition. The earliest systematic investigation was made by Frisak (1923) who attempted to establish a limiting chemical composition for foamable slags. He decided that foamable slags covered most blast furnace slag compositions on the basis of silica, alumina, and lime, and further "that the replacement of lime by magnesia up to 15 per cent has no noteworthy effect on foamability, that moderate quantities of alkalis are not deleterious, that sulphur raises the foamability and that MnO is only deleterious in the presence of 1...

Jan 1, 1963

By José Carlos do Amaral, Marcelo Groszownik, Jorge Beim

"Initiated in 2008, the project of this 1800 km long Electrical Transmission Line is a job of extreme technical complexity, crossing regions of major forests and rivers. When ready, it will allow the large Brazilian states of Amazonas, Amapá and Pará to use the energy from hydroelectric plants, thus eliminating the need for the use of diesel fuel thermal plants, with their much larger environmental footprint. Due to its extraordinary characteristics, the Green Peace and the Discovery Channel constantly visited the job. The part between the Amazon and the Xingu rivers started in 2012, and encompassed about 100 transmission towers with up to 150 m height, through a region known as “Alagados”. This region exhibits a 1.5 m water level during the rainy season, and soaked ground the rest of the year. Navigation of regular vessels is impossible during the flood season, when a dense vegetation called “bulhado” fills the riverbed, and vehicle traffic is impossible during the dry season, due to the extremely low surface soil resistance. Great logistical and technical difficulties were encountered for driving and determining the capacity of the piles. New systems had to be developed for driving the piles, with the simultaneous use of 15 small piling rigs. The final penetration, total number of hammer blows during driving, plus Dynamic and Static Load Tests were used for determining the driving and acceptance criteria.The geographical challenge and initial conditionsThis paper describes the execution of foundations for a 500 kV Electrical Transmission Line in a region that becomes flooded during the rainy season and heavily muddy during the dry season. This is the monsoon climate, typical of the equatorial region of Brazil, where there is a rainy season lasting for about half the year, followed by a very dry season. The temperature varies very little throughout the year, due to the proximity to the equator. The locals call the rainy season “winter” and the dry season “summer”.The most important part of the so-called “Alagados” region is situated inside an Environmental Extractive Reserve (RESEX) called “Verde para Sempre” (Forever Green), created in 2003. This is one of the largest environmental reserves in Brazil. It is an area controlled by the Brazilian Environmental Control Department, the Chico Mendes Institute (ICMBio). The environment control parameters are very strict.No deep foundation had ever been executed before along the “Alagados” region. The main challenge faced on this job, however, was working in a place where self-propelling vessels or land vehicles and equipment cannot be used. During the rainy season there is a dense and intricate vegetation called “bulhado”, which prevents the movement of outboard motor boats with propellers going deeper than 50 cm. In the dry season, the heavy mud prevents the movement of foundation equipment, excavators, trucks and other machinery."

Jan 1, 2015

The observation of lower-than-predicted Fe/Cu ratios in the cementation of copper on iron in tests at elevated temperatures indicated that some other reaction was contributing to the reduction of cupric sulphate in addition to the reduction by elemental iron. Experiments showed that the copper sponge, which initially formed on the iron, subsequently reduced the cupric sulphate giving the products cuprous oxide and sulphuric acid.Tests were undertaken to determine the rate and equilibrium conditions of the reduction reaction with variations in the types of the reducing agent and solution parameters. The reaction first became apparent at temperatures above 50°C and as it ceased at pH 1·8 it was possible to induce further reaction by alkali addition.

Jan 1, 1974

By K. J. Liles

Research was undertaken by the Bureau of Mines to determine the technical feasibility of producing lightweight aggregate from the waste glass fraction of municipal incinerator residues. Tests were conducted to determine the amount and optimum size of glass, the amount of sodium silicate, and the method used to form the material to be expanded. The most suitable mixture, 78 percent glass, 20 percent clay, and 2 percent sodium silicate, was pelletized and then expanded by exposure to a temperature of 1,550° F for 15 minutes The resulting lightweight material had a bulk density of 38 lb/cu ft and exhibited excellent pore structure. Concrete test cylinders made from the light weight aggregate had a unit weight of 104 lb/cu ft and a compressive strength of 2,550 lb/sq in after a 28-day steam cure.

Jan 1, 1976

GOOD ventilation is recognized as an essential for the preservation of health, and laws have accordingly been framed in many countries for the provision of adequate ventilation in factories and places of public resort as well as in mines.Apart from the legislative enforcement of hygienic measures as a matter of public 'policy, the ventilation of mines has an important economic aspect, since it affects to a large extent the industrial efficiency of the workmen, and consequently the cost of mineral production. Until recent years the ventilation of metal mines has not generally received much consideration, and the importance of pure air has been sometimes overlooked. To the absence of explosive gases in such mines, and to the cost of the installation and working of mechanical ventilators, may generally be attributed disregard of adequate ventilation. In this paper it is not proposed to furnish statistics on the mortality and morbidity of miners, or a treatise on the medical aspect of the rock-dust problem, to further elaborate which would be superfluous, the deleterious effects of the latter having been...

Jan 1, 1912

By Yoginder P.

ACKNOWLEDGEMENTS Authors sincerely appreciate the interest, cooperation and technical support of the coal company management and staff in conducting the study. Without their assistance this study would not have been possible. INTRODUCTION AND SPECIFIC OBJECTIVES An area in the midwest overlying abandoned room-and-pillar mine workings at, shallow depth has been experiencing subsidence movements with associated damage to surface structures. Other coal companies in the area have also been having similar experience. A 16 - month cooperative study between a mining company and the Department of Mining Engineering at SIUC was developed with the following objectives. 1) Determine the extent to which surface and subsurface movements were complete in the area, 2) Identify the mechanism(s) of subsidence in the area, 3) Determine the influence of geology and hydrology of the area on subsidence movements, 4) Observe the conditions of abandoned underground workings with a borehole TV camera, 5) Characterize the extent of damage and monitor possible progressive damage to selected surface structures, and 6) Make recommendations to a) minimize further damage to surface structures in the area, b) identify future areas that may be affected by these movements and c) modify mining systems to minimize these movements.

Jan 1, 1986

By R. G. Bentsen, D. A. T. Donohue

The cyclic steam injection process has become the most widely applied and most successful thermal recovery technique in use today.1-4 Normally, steam stimulation is repeated several times during the life of a project. The problem is to select the optimum number and size of steam treatments so that the profits realized over the entire life of the project are maximum. Obviously, operating costs rise directly with the frequency and amount of steam injection. Operating efficiency, on the other hand, can be adversely affected if the amount and frequency of stimulation are insufficient. Thus arises a multistage decision problem; that is, a decision must be made at each sub-period (day, for example), as to whether steam should be injected, and, if so, how much. It is desirable that these decisions be made in such a way as to secure maximum net profit before taxes. This can be achieved by dynamic programming. To use dynamic programming, we must be able to predict not only the production rate-time curve resulting from a given stimulation, but also how changes in stimulation policy will affect this curve. In this study, the effect of steam injection on well performance is estimated on the basis of a simple model that takes into account both steady-state and transient flow. Oil production rate is calculated for both types of flow, and the larger of the two values is used. This allows the calculation to change to radial steady-state flow at such time as this mechanism becomes more effective than the transient mechanism. We propose to show how dynamic programming can be used to optimize the steam soak process with respect to net profit. For this, a mathematical representation of the steam soak technique is necessary. A further objective, therefore, is the formulation of a mathematical model capable of realistically simulating the physical process. Oil Production Response Model The advantage of using a mathematical model is its generality and ease of manipulation. However, the model must be an accurate representation of the physical process, for a solution derived from a model can be no better than the model itself. The question now arises as to how well the model should be expected to simulate reality. In general, the simplest model should be tried first, for additional accuracy is apt to require additional cost and time. Also, the search for a high degree of accuracy may yield only greater complexity and difficulty without yielding significantly better results. With this in mind, we kept our model as simple as possible, yet generally representative of the actual physical process. The number of state variables is limited to three, and stochastic variations in the parameters are ignored. As a consequence, use of this model should be restricted to cases in which the underlying assumptions are not severely violated. In

Jan 1, 1970

By David Norval

The increased tendency to use hydrometallurgy as an extraction step towards final refining following a pyrometallurgical smelting process requires melts which have to be cast and or comminuted which can then be taken up into solution or leached. To generate surface area for optimal leaching, a common process is to granulate and in many cases mill, which is a general practice with friable material with properties associated with higher sulphur, carbon and silicon levels. However, in the case of metallic melts milling can be unfeasible due to the ductility of the granulated particles. Water solidification is capable of producing either fine particles by means of granulation or atomisation. Atomisation however, can produce particles as fine as 40 microns without a milling circuit.

Jan 1, 2005

By E. Amini

"While methods exist to allow the simulation and optimization of existing flotation operations, there is a deficit in the ability to predict the performance of a new ore type pre-processing. A laboratory scale batch flotation testing methodology has been developed to assess the flotation potential of ores (known as the JK Floatability Index or JKFI). Previous work conducted by Alexander and Collins (2008) showed that the test could be used to predict full scale results in base metal ores. In this work, JKFI tests were applied to three different types of ore and one blend from a greenfields gold deposit to show the test applicability to flotation of precious metals. The results from the JKFI test on one ore type were then used to predict the response of all ore types (including the blend). To validate the predicted kinetic parameters, a comprehensive survey was performed on a pilot plant where each of ore types was processed in the circuit. An acceptable agreement was found between the experimental recoveries and predicted recoveries which indicate the potential of this method for use in predicting the flotation response of an ore.INTRODUCTIONOver 100 years, flotation has been considered an efficient method to concentrate different types of sulphide and oxide minerals and coal. Thus, numerous research studies have been undertaken to find an appropriate model to predict the behaviour of particles in flotation circuits (Barnwal et. al., 2006; Bascur and Herbst, 1983; Cecile and Villeneuve, 1991; Deng et. al., 1996; Zheng et. al., 2006). Most methods are based on the ore flotation response in an industrial plant which is expensive and time consuming to characterise. It is difficult to reliably predict flotation response for new types of ores in industrial scale plants.The floatability component modelling (FCM) approach, developed within the Australian Minerals Industry Research Association (AMIRA) P9 project, has been used to derive models of operating flotation plants for the purpose of simulation and optimisation (Alexander and Morrison, 1998; Alexander et. al., 2000; Varadi, 2006). This approach has been applied at a large number of operating sites treating a wide variety of ores. The approach requires metallurgical surveys to be undertaken in conjunction with batch flotation tests and cell characterisation. This allows ore and machine parameters to be derived, which are then used in the P9 Flotation Model. The development of a FCM generally requires a large commitment of resources and time. While there has been significant support of this approach in industry, the FCM approach is limited to ores already being processed (Runge, 2004; Wightman, 2006)."

Jan 1, 2009

By Graham A. Mathieson

The precise definition of an ultimate or economic pit has, over the years, received much attention in the literature on the subject of mine planning. Unfortunately, relatively little has been published in the area of pit sequencing and scheduling--an aspect which is typically of much greater economic significance both during the life of a mining operation, as well as in the evaluation of an exploration project. This paper discusses an overall mine planning methodology with emphasis on the design of an optimal sequence of pit expansions or phases. Although the concepts given are not new, it is hoped that some practical suggestions will be made. The paper will also describe graphical techniques which have been found useful in comparing the merits and impacts of alternate planning strategies and production schedules.

Jan 1, 1982

By L. B. Pankratz

Thermodynamic data on carbides, nitrides, and other selected substances were reviewed, evaluated, and compiled at the U.S. Bureau of Mines Albany Research Center. Values for Cp°, S°, H° - H°298, -(G° - H298)/T, ?Hf, ?Gf, and log Kf are given in tabular form. Cp°, H° - H°248, ?Hf°, and ?Gf° are also expressed algebraically.

Jan 1, 1994

By D. R. Wilburn

The worldwide budget for nonferrous, nonfuel mineral exploration was expected to increase by 58 percent in 2004 from the 2003 budget, according to Metals Economics Group (MEG) of Halifax, Nova Scotia. The increase comes two years after a five-year period of declining spending for mineral exploration (1998 to2002). Figures suggest a subsequent 27 percent increase in budgeted expenditures from 2002 to 2003. For the second consecutive year, all regional exploration budget estimates were anticipated to increase. The worldwide budget for gold exploration achieved about 50 percent of the total amount budgeted in 2004.This was 68 percent, or US$715 million, higher than the reported 2003 budget. The 2004 worldwide exploration budget estimates for copper increased by 70 percent, orUS$237 million, to US$577 million from the 2003 budget. The budget for nickel exploration increased 52 percent, or US$89 million more than in 2003. The 2004 exploration budget for other mineral targets (primarily cobalt, heavy minerals, industrial minerals and silver) increased114 percent, or US$118 million.

Jan 1, 2005

By A. W. Dickerson, G. Hollier, F. A. Bartley

Following on from many years of research aimed at improving the effectiveness of truck haulage operations in mines operated by BHP Minerals, BHP Research developed a concept for an Innovative Large Mining Truck, (ILMT) which has the potential to significantly improve the cost effectiveness of rear dump mining trucks. The ILMT concept reduces the empty vehicle weight dramatically, greatly reduces unequal rear tyre loading and improves ride and handling characteristics. The concept has been taken to the "proof of concept" prototype truck stage with the cooperative efforts of BHP Coal, BHP Research. Liebherr Mining Truck, Inc., Liebherr-Australia and Birrana Engineering. Testing of the prototype truck commenced at a coal mine in Queensland, Australia during May, 1996. Preliminary results from the testing program are very encouraging. Expectations are being met and in some cases exceeded.

Feb 24, 1997

By Duane A. Smith

They are gone now. Gone like that long ago generation that gave them birth. The Homestake Mine, nestled in the northern Black Hills, closed in 2001 after 125 years, the longest run of any major American gold mine. The Homestake Mining Co., which guided its destiny for those many years, is gone too. It merged with Barrick Gold. The Hearst family, which guided the early destiny of both, has long since gone beyond its mining heritage and into the national and even international spotlight. The mine and the company passed from the scene with as little fanfare as heralded their birth, amid the Black Hills gold rush of the 1870s. They both grew into American mining legends, as did the town they sired and nurtured, Lead. In a real sense, the mine and the company symbolized one of the last links to a vanished world and a mining era.

Jan 1, 2003