Search Documents

By D. Lusinga

Hydrocyclones are a common feature in almost all mining operations in the world, serving mainly as classifiers. Some of their advantages include low capital costs, low space requirements and their ability to reduce residence time in closed circuit grinding processes. Although an extensive body of literature exists for hydrocyclones, these devices are still inherently inefficient, and more research is currently being undertaken, particularly in the field of modelling. In the vast body of hydrocyclone literature published so far, there has been little or no effort devoted to analysing the effect of the cone force ratio on the performance of hydrocyclones. The cone force ratio is defined as the ratio of the spigot to the vortex finder diameter (Shah, 2005). In this study a total of 44 tests was carried out in a custom-built rig at the University of Cape Town. These tests were aimed at evaluating the effect of the cone force ratio on the performance of as mall diameter hydrocyclone. The cut size and water split were used as the criterion for evaluating the performance of the hydrocyclone. Results from the tests showed that the cut size decreased with an increase in the cone force ratio. The cut size also appeared to decrease as the calculated locus of zero vertical velocity (LZVV) shifted inwards. The water recovery to the underflow appeared to increase with an increase in the cone force ratio. The effect on the cut size of adjusting the cone force ratio was found to be higher for a coarser feed than it was for a finer feed.

Jan 1, 2009

By Mostafa Benzaazoua, Mariam El Adnani, My Ahmed Boumehdi, Rachid Hakkou, Salah Ouhamdouch, Abdelmalek Goumih

This study focuses on the environmental characterization and assessment of long-term neutral mine drainage (CND) potential from waste rock piles at the abandoned Erdouz mine in Morocco. The study involved metallographic analysis, static tests, and column tests. Results indicate that the waste rock is not an acid mine drainage generator but produces CND, mainly with sulfates exceeding Moroccan standards. The waste rock is relatively stable and could be reused after pretreatment.

Jan 25, 2022

By J. Drelich, M. Pawlik

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size, and distribution of mineral inclusions in coal, on its wettability are briefly reviewed.

Jan 1, 1999

By Charles Will Wright

The present struggle for economic and industrial supremacy by the Communist world is against the United States, its main target, and the other Free World nations. The basis of industrial power is minerals, so the Communist nations are building up mineral production within their borders, often regardless of costs, and are acquiring quantities of mineral products from Free World countries for future use. They are contracting for additional supplies and advancing funds for the development of these quantities. A number of the less developed mineral producing countries of the Free World are being infiltrated by Communists and Communistic influence. This situation is well known, but as yet little has been done to oppose these activities or to awaken the public to their seriousness. The Communist countries are still far behind the Free World Nations in production of many essential minerals. But, shortages are being made up from Free World nations in exchange for petroleum, manganese ore, chromite and other products. Restrictions on shipments of strategic materials to Communist countries have not been maintained.

Jan 1, 1964

By Wilbur L. Webb

An electrically powered methane sampling system for application on mining machines was designed, fabricated and laboratory tested. The system will sequentially draw sample air at a controlled rate from up to three machine positions across the mine face and deliver the air to either an approved methane monitor, methanometer or flame safety lamp. The prime considerations in the design were to provide an intrinsically safe, water and dust resistant control box and an explosion-proof power box capable of being operated from the various mining power sources. The power box contains an internal battery that provides operating power prior to mining machine start-up and alter machine shut-down. The internal battery is recharged automatically when mining machine power is available.

Jan 1, 1977

By E. Gallestey, D. Groenveld, F. Kolb, M. Rozou

"Recent copper price evolution pushes modern mining industry even harder to achieve highest production with maximum efficiency. Operations are bound by numerous contractual and environmental conditions that bring a high degree of complexity to both the operators controlling the process and the plant managers assessing the circuit’s potential and setting the production goals.Advanced process control (APC) for grinding is one important tool to operate this most energy intense area in an optimal way, finding the optimal trade-offs between highest throughput, energy efficiency and product quality based on variable ore properties, production targets and management priorities.ABB’s state of the art control and optimization software platform enables user to design a controller based on model predictive control (MPC). The paper and the presentation show the technology used and the results achieved through an APC controller installed in a pilot project in Aitik (Boliden SA), Sweden. Furthermore, possibilities to interconnect grinding with other areas as stockpile management and flotation with various interconnected APC controllers will be shown. Finally, an example of the return on investment and the payback times based on the increased throughput and better product quality will be presented.INTRODUCTIONDepending on the ore characteristics and the targeted plant capacity, the design of the grinding circuit may vary significantly. Typically, the circuit consists of several mills (rod, ball, SAG, AG) in series and/or parallel with a number of classifiers and sumps at appropriate locations (see Figure 1).The main goal of the grinding section is to reduce the ore particle size to a level that enables efficient separation between gangue and precious metals in the subsiding processing step. The trade-off between quality and quantity has to be made. At the same time, it is also crucial to execute this process at the lowest possible energy and grinding media consumption."

Jan 1, 2015

By Taylor R. G

This paper reports a biogeochemical study of the Siberia lode of the Herberton tin field. Soil near the orebody contained high levels of Fe, Cu, Pb, Sn, As, Mld Mn. Polycarpaea spirostylis and Indigofera dominii were associated with these high levels but several other species apparently could not tolerate them. The potential of these species as indicator plants is discussed.

Jan 1, 1975

By O. Rabeau, M. Legault, A. Cheilletz, L. Z. Cheng, J. J. Royer, M. Jébrak

"By compiling geological, structural, geophysical, and geochemical information into a 3D geological model, we evaluated the orogenic gold potential in the vicinity of a hidden segment of an important Archean fault zone, the Cadillac-Larder Lake fault (CLLF) in the region of Rouyn-Noranda. The segment of CLLF in the present study is partly covered by Proterozoic sedimentary rocks. Because more than 2000 t Au have been extracted along the CLLF to date, our objective is to evaluate the gold potential at depth along a poorly known segment of this fault. A 3D geological model (50 km × 9 km × 1.5 km) including the covered segment was built through the compilation and homogenization of available geological data and the construction of 23 cross sections. The geology under the Proterozoic cover was evaluated using geophysical inversions, drill holes (42 in total), and surrounding geology. All available assays were filtered and upscaled to a 250 m × 250 m × 250 m regular cell grid to determine and quantify spatial relationships between geological features and mineralized occurrences using the weights of evidence method. Structural features, such as E-W-trending faults and fault intersections, and certain lithologies with a high primary porosity such as volcanoclastic rocks of the Blake River Group and Timiskaming sedimentary rocks, proved to be very prospective, yielding favourable factors with a weight of evidence index W+ > 0.24. These salient features were then assigned a combination index for ultimately evaluating the orogenic gold potential under the sedimentary cover. The zones resulting in an optimization of exploration targeting were attributed the highest probability, representing ~1% of the initial volume. La compilation des données géologiques, géophysiques, structurales, et géochimiques et leur intégration au sein d’un modèle géologique 3D a permis d’évaluer le potentiel aurifère dans les environs d’une importante zone de faille archéenne sous couverture protérozoïque. Cette méthodologie a été développée en utilisant le cas de la Faille Cadillac-Larder Lake (FCLL) dans la région de Rouyn-Noranda. Puisque plus de 2000 t d’Or ont été extrait à proximité de la FCLL, l’objectifs des travaux est l’évaluation du potentiel aurifère en profondeur de ce segment. Un modèle géologique 3D (50 km × 9 km × 1.5 km) incluant le segment sous couverture de la FCLL a été construit en utilisant l’ensemble des données géologiques disponibles et 23 coupes géologiques. La géologie du socle archéen sous la couverture protérozoïque a été interprétée avec des inversions géophysiques, des forages (42 au total) et les contacts géologiques exposés. Les teneurs aurifères dans le secteur ont été filtrées et ajusté à une grille régulière de 250 m × 250 m × 250 m afin d’évaluer et de quantifier les relations spatiales existantes entre certaines entités géologiques et les emplacements minéralisés en utilisant la méthode du poids de la preuve. Les failles de direction Est-Ouest, les intersections de failles ainsi que certaines lithologies possédant une porosité primaire importantes comme les certains tuf du Groupe de Blake River et les sédiments du Timiskaming se sont montrés très prospectifs avec des valeurs de W+ > 0.24. Ces entités géologiques ont ensuite été utilisées par le biais d’un indice de combinaison pour évaluer le potentiel en or de type orogénique sous le couvert sédimentaire. Cette méthodologie permet une optimisation des campagnes d’exploration puisque les zones pour lesquelles la probabilité de minéralisations a été évaluée à la plus haute valeur représentent 1% du volume initial."

Jan 1, 2009

By W. M. Myers

Jet is a substance of organic origin and has been defined by the U. S. Geological Survey as a "dense black lignite, taking a good polish, and sometimes used for jewelry". Jet is characterized by the lustrous, intense black surface it displays when polished. It is due to this property that the expression "jet black" is so commonly used to imply intense blackness.

Jan 1, 1923

By Gerald V. Gibbs

Quadratic functions, Q(hkl), are given to six places in increments of 0.01° for 2? from 0° to 90° for CuKa and from 25° to 180° for CuKa1. The wavelengths used for Cu in the computation are those agreed upon by the Editorial Commission of the International Tables for X-ray Crystallography (1950): CuKal 1.54051 A.; CuKa2 1.54433 A. INTRODUCTION At the Federal Bureau of Mines laboratory, Norris, Tenn., X-ray diffraction crystallography using tubes with copper targets revealed a need for a handy reference for the quadratic functions of copper radiation. The tables presented here were prepared to satisfy that need. The quadratic form Q(hkl) may be expressed in terms of the Bragg diffraction angle 2? and of the wavelength ? as

Jan 1, 1961

By Jacques Ouellet, Ferri Hassani

"Within the mining industry paste backfill technology has evolved over the last two decades. This technology aims at producing safe and cost effective backfill of high strength. When used as cemented backfill underground the usual practice in the mining operations was to consider the backfill as a component under the production engineer responsibility. With its growing use in various site conditions some problems were encountered. Over time the mechanical characteristics of paste backfill could deteriorate. Investigations on these problems brought an increased understanding of paste backfill chemistry. Effectively, paste backfill is produced with tailings slurry having sometimes very complex chemistry and mineralogy. The bonding agents can be sensitive to the chemistry of these slurries. Today, a new understanding of the complex chemical reactions involved in cementing paste backfill is derived from concrete research literature. Cemented paste backfill is a manufactured product and as thus all steps involved in its making must be looked at. Both the processing engineers and mining engineers need to be involved. The proposed paper will go over the various developments and new understanding gained over the years on paste backfill chemistry. The authors had the opportunity to work with various Canadian mines that implemented paste backfill in their operations. Chemical alterations case study will serve to illustrate the importance of a good understanding of cement and paste chemistry. The authors will then conclude on research orientations needed to bring a more efficient use of paste backfill technology. The crucial role of the processing engineers in the paste backfill manufacturing will be discussed.INTRODUCTIONPaste backfill is usually prepared from a mixture of solids and water containing at least 15% particles smaller than 20 microns with the addition of binders for mechanical strength. Historically, tailings had been classified to extract the fines and only the coarse part was placed underground as sand slurry. Paste fill was researched in the last three decades to enable mining operations to use all the tailings, including fines, in backfill. The outcome of the early studies showed that paste fill provides high strength but due to preparation complexities and transportation problems is expensive. A greater understanding of the transportation mechanisms and advances in dewatering technology in recent years has resulted in more practical use of paste backfill."

Jan 1, 2002

By P. M. Ambrose, C. Travis Anderson, Cresap Moss, R. S. Dean

"MANGANESE METALMethods of PreparationMethods of preparing the manganese metal that has been used in chemical and metallurgical investigations have passed through a cycle. Most of the investigations made before the turn of the century used Moissan's pyrophoric manganese. 5/ This material was made by electrolysis into a mercury cathode and distillation in vacuo. It was essentially a pure material, and investigations in which it was employed (with proper precautions against oxida¬tion) led to accurate results concerning the intrinsic behavior of metallic manganese.An early investigation of the properties of ""Manganese-by-Mercury"" was made by M. Guntz. 6/ He prepared manganese by electrolysis of a concentrated MnCl2 solution with a mercury cathode. The manganese amalgam was pressed through chamois and distilled in vacuo (2 to 3 cm. of mercury) at 200°0., slowly rising to 250°0. Guntz recognized especially the decreased reactivity of manganese with increased temperature of mercury distillation. The most careful and com¬prehensive study of manganese made by this method is that of Kuh 7/ whose work unfortunately was never published in an accessible journal.Royce and Kahlenberg 8/ studied the electrode potential of manganese made by this method."

Nov 1, 1939

By Fredrick L. Johnson

The Bureau of Mines, under Congressional mandate, conducted a mineral survey on the Park Range WSA (Wilderness Study Area) in 1984 and 1985. The WSA, located about midway between Tonopah and Ely, encompasses 47,268 acres. No mineral resources were delineated, nor were workings found, during the investigation. There has been, however, exploration in and near the north end of the study area. ASARCO is actively exploring a block of 41 claims for hot-spring type, low-grade, large-tonnage gold deposits. Their claim block is almost entirely in the study area. The Morey mining district, 7 miles southwest of the study area, produced silver and lesser amounts of gold and lead sporadically from the mid-1860's through the mid-1960's. The WSA is underlain by Tertiary rhyolitic and latitic volcanic rocks and by Paleozoic sedimentary rocks. The Paleozoic rocks have been faulted, silicified, brecciated, and hydrothermally altered, and have anomalous concentrations of precious metals and pathfinder elements. Additional exploration in the north part of the Park Range WSA may lead to delineation of gold resources.

Jan 1, 1986

By Dr. Peter J. Conroy

The current study is part of the U.S. Department of Energy's (DOE) on-going subsidence research program. The long-term objective of the DOE program is to develop analytical methods of subsidence prediction applicable over a broad range of geologic and mining conditions encountered in the United States. The DOE currently has several contracts in progress to develop a sound data base that can be used in the development of predictive models. Dames & Moore is currently under contract to the DOE to collect and analyze detailed subsidence and hydrologic data from a coal mine employing longwall mining methods in the Eastern Coal Province. Work under Contract No. DE-AC22-80PC 30335 began in October of 1980 and will continue through September of 1984. This paper summarizes the work that has been completed through September of 1981 and presents the results that have been achieved during this period. Technical difficulties encountered during both the installation and monitoring phases are discussed, and recommendations for future work are presented.

Jan 1, 1982

By G. M. Brownell

A DEPOSIT of hematite occurs on Black island, lake Winnipeg, at a point known locally as Red Rock, on the south shore of the island directly across from Clements point. The mail boat from the Canadian Pacific Railway terminus at Riverton, crossing the lake to Manigotogan twice weekly, passes near Red Rock and provides a convenient means of transportation to this part of Black island (Figure 1). HISTORICAL The occurrence of hematite on Black island has been known for a long time. Dowling's report of 1898 states(1): "An iron-ore deposit on the south side has been known' for many years, and on Jeffrey's map of 1762, showing Canada and northern part of Louisiana, Iron island is shown a short distance south of the narrows, evidently the same as the Black island of today".

Jan 1, 1945

By Thomas M. Barczak

The 1990s brought an unprecedented increase in the development of innovative technologies to provide more effective and easier-to-install roof support in underground mines. To facilitate the application of these technologies in improving mine safety, the National Institute for Occupational Safety and Health (NIOSH) developed the Support Technology Optimization Program (STOP). STOP is a Windows-based software program that provides mine operators with a simple and practical tool to make engineering decisions about the selection and placement of these various roof support technologies. The program includes a complete database of the support characteristics and loading profiles obtained through safety performance testing of these supports at the NIOSH Safety Structures Testing Laboratory. A support design criterion in the form of the required support load density at a specified convergence can be established from four options: (1) a database of measured ground reaction obtained from various mines or ground behavior information input by the user,(2) load requirements based on a detached roof block or rock failure height, (3) criteria based on the current roof support system, and/or (4) arbitrary criteria set by the user. Using these design criteria, the program will determine the installation requirements for a particular support technology that will provide the necessary support load density and convergence control. Optimization routines are also available to determine the most efficient support design for a user-specified support installation. In addition to these performance measures, STOP can be used to compare material handling requirements and installation costs. Comparisons among the various support technologies are easily made, including a graphical analysis of relevant support parameters. This paper describes STOP and its application to optimizing standing secondary roof support systems.

Jan 10, 2000

By M. Hagfors

When establishing an underwater testing site for the energy measurements of the explosives, the dimensions of the measuring pool have to be measured to find out what is the maximum weight for the test charge. Secondly one has to decide the distance between the pressure gauge and the shooting point. Thirdly the pool has to be calibrated because of the reflections of the explosions by measuring the bubble periods of the calibration charges. The calibration shots can also be used to estimate the minimum weight of the explosive charge for the reliable energy measurements by calculating the shock, gas heave and total energy values and their standard deviations.

Jan 1, 2007

By F. N. Voskoboyev

The suggested new method for control of geomechanical state of undermined rock mass ensures, as a safety measure for the earth surface protection, the decrease of deformations by 2,5 - 10 times in mining the single seam, and by 1,5 - 5 times - in mining bed series, i. e. approximately within the seam ranges as in the application of full packing with various compressive properties or partial extraction of resources over the area with different coefficients of extraction. It should be noted that this new method has the following advantages o\w rhr. conventional methods: a) the decrease of the packing area and packing works volume by 2 - 4 fold including the operating and productive expenses; b) the elimination of mineral losses due to the increase of extraction coefficient up to 100 5%; c) rock utilization from workings drivage by its placing in the mined - out space. Perspective field of application of this method: disconservation of mineral resources in the left protective pillars of various designation.

Jan 1, 1996

By Walter R. Storms

"INTRODUCTION The New Mexico potash exploration described herein was begun in February 1944 with the object of determining the amount of potash ore in the United States Potash Reserve in Eddy County by exploring the deposit from the surface with vertical drill holes. The work was completed in October of the same year after 16 holes had been drilled on the Reserve and in the immediate vicinity.The Potash Reserve is in secs. 26; 27, 34, and 35, T. 20 S., R. 29 E., Eddy County, N. Mex., about 14 miles northeast of Carlsbad, as shown on figures 1 and 1A, Drilling was done in secs. 26 and 35 of the Reserve, in section 14 to the north, end sections 2 and 56 to the east. All work was done on Governnent-owned, unleased land.The Reserve may be reached from Carlsbad by traveling to the north-east by automobile for about 14 miles on the paved U. S. highway 62. This highway passes through the southern part of the Reserve. Other parts may be reached by a State highway that passes along the eastern side of the area, then by poor dirt roads to various drilling sites. A branch of the Santa Fe Railroad also passes across the southern part of the Reserve enroute from Carlsbad to the plant and mine of the Potash Co. of America, a few miles northeast of the project and 22 miles from Carlsbad."

Aug 1, 1947

By B. S. Xakalashe

Keywords: Pyrometallurgy, silicon, solar cells Silicon has been the dominant material in the photovoltaic (PV) industry since its application in the space industry in 1958. This review focuses on crystalline silicon solar cells, primarily due to their dominance in the photovoltaic industry, omitting other photovoltaic cell technologies such as second generation (e.g. thin films) and third generation (e.g. nano-structured solar cells). The value chain for the production of crystalline silicon solar cells has been reviewed. The primary processing steps for the production of silicon solar cells from quartz are as follows: bulk production of metallurgical-grade silicon via carbothermic reduction in a submerged furnace, refining of metallurgical-grade silicon via the chemical means to polycrystalline silicon, or through the metallurgical route to solar-grade silicon, wafer manufacturing, and, lastly, silicon solar cell manufacturing. During downstream processing, solar cells are interconnected and encapsulated into solar modules (panels), which can be used individually or incorporated into a photovoltaic system for electricity generation and supply. The cost for crystalline silicon based solar cells is approaching one US dollar per watt peak ($1/Wp), while the most cost-effective solar modules in industry have reported costs below $1/Wp, and are based on CdTe thin films. Solar cell energy conversion efficiencies as high as 22% have been reported in industry for crystalline silicon solar cells.

Jan 1, 2011