Search Documents

By C. A. Rowland Jr

"I. INTRODUCTIONFred C. Bond's ""Third Theory of Comminution"" (1) was published in 1952. The mathematical statement of the Third Theory is the well-known Bond Formula:where W - Kw H per short tonWl - Work IndexP - Product size in microns which 80% passesF .. Product size in microns which 80% passesWork Index, as defined by Fred Bond, "" ... is the comminution parameter which expresses the resistance of the material to crushing and grinding. Numerically, the Work Index is the KwHrs per short ton required to reduce the material from theoretically infinite feed size to 80% passing 100 microns."" (2)Work indices for grinding can be obtained tram Bond grindability tests and can be calculated from plant grinding mill operating data when power consumed per ton of ore ground, the feed size analysis and the product size analysis are known.Work indices obtained tram Bond grindability tests, having been obtained from standard and controlled laboratory procedures, are reproducible and for the sample tested are accurate. The degree of accuracy relative to plant mill operation depends upon how representative the sample is of the total mill feed.The results of the Bond closed circuit rod and ball mill grindability tests (3) are given in grams of product sized material produced per revolution of the test mill. In developing a method to evaluate plant operating data and results from his grindability test, Fred Bond developed the ""Third Theory of Comminution."" In the process formulae were developed for converting grams per revolutionobtained from grindability tests to work index.The standard feed sizes for the Bond grindability tests are:Rod Mill Test ore crushed to minus 1ll inchBall Mill Test ore crushed to minus 6 mesh (Tyler)The formulae for converting grams per revolution to work index incorporate the 80% passing sizes for the feed to and the product produced in the specific test. Therefore, accurate work indices can be obtained from Bond grindability tests when the feed size is finer than standard. To obtain accurate test results, the ratio of reduction should be greater than 6 to 1."

Jan 1, 1972

By Rodrigo Toro, Mario Delisle, Claudio Zamora

"The mining market is researching innovative methods to train the workforce for mining which is normally extremely difficult to get. Thus, the dynamic simulation-based technologies become an essential pillar to educate and train the inexperienced staff at the pace required by this industry. Even if Operator Training Simulator (OTS) systems are commonly used in most of industries, knowledge transmitted to operators are unfortunately not ""capitalized"" in general. The OTS systems are usually delivered as a single hardware and software platform and very little as a full service long-term.In this article, an integrated solution to increase the efficiency of the operators is proposed. This solution is based on the combination of dynamic simulation, processes knowledge, virtual reality and the knowledge capitalization through the creation of simulation scenarios and e-learning. The Codelco Ministro Hales plant simulation project for a copper concentrator plant is presented as a real life example.IntroductionDynamic and real-time process simulation have proven to be a must in the development of greenfield projects, providing mechanisms to design and test controls design, interlocks, start-up, shut down sequences and operator training, among others (see (McMillan, 2006) for further details). Early adopters of this technology were utility power plants; in the petrochemical industry have become a standard, and in the mining industry the use of dynamic simulations is growing, especially in new projects and training of operations personnel for the adoption of best practices and new technologies, see (Nikkhah & Anderson, 2001) and (Toro, Ortiz, & Yutronic, 2012).This paper outlines a solution that utilizes dynamic simulations as the base of an integrated platform for operational effectiveness, which takes into account the current scenario of new mining projects and operations, where high turn over rates and needs of specialized workforce have given a special value to this kind of technologies."

Jan 1, 2015

By E. Gallestey, D. Groenveld, F. Kolb, M. Rozou

"Recent copper price evolution pushes modern mining industry even harder to achieve highest production with maximum efficiency. Operations are bound by numerous contractual and environmental conditions that bring a high degree of complexity to both the operators controlling the process and the plant managers assessing the circuit’s potential and setting the production goals.Advanced process control (APC) for grinding is one important tool to operate this most energy intense area in an optimal way, finding the optimal trade-offs between highest throughput, energy efficiency and product quality based on variable ore properties, production targets and management priorities.ABB’s state of the art control and optimization software platform enables user to design a controller based on model predictive control (MPC). The paper and the presentation show the technology used and the results achieved through an APC controller installed in a pilot project in Aitik (Boliden SA), Sweden. Furthermore, possibilities to interconnect grinding with other areas as stockpile management and flotation with various interconnected APC controllers will be shown. Finally, an example of the return on investment and the payback times based on the increased throughput and better product quality will be presented.INTRODUCTIONDepending on the ore characteristics and the targeted plant capacity, the design of the grinding circuit may vary significantly. Typically, the circuit consists of several mills (rod, ball, SAG, AG) in series and/or parallel with a number of classifiers and sumps at appropriate locations (see Figure 1).The main goal of the grinding section is to reduce the ore particle size to a level that enables efficient separation between gangue and precious metals in the subsiding processing step. The trade-off between quality and quantity has to be made. At the same time, it is also crucial to execute this process at the lowest possible energy and grinding media consumption."

Jan 1, 2015

By Willemijn Husslage

Tata Steel Group At a glance ? Part of the Tata Group ?Tata Steel Group: ?Fortune 500 company ?Top 10 global steel producer ?Annual crude steel capacity of 28 million tonnes ?More than 80,000 employees ?Manufacturing operations in 26 countries across 5 continents ?Serving customers all across the globe ?Turnover 2009-10: $22.8 billion

May 1, 2011

About MAC ? The national organization of the Canadian mining industry ? Mining, smelting and refining of base and precious metals ? Mining of iron ore, diamonds, uranium, oil sands, coal and industrial minerals ? Many associate members ? www.mining.ca

Aug 1, 2013

By Marc C. Bétournay

Over the last four years, an international initiative, championed by Vehicle Projects LLC, the Fuelcell Propulsion Institute and Natural Resources Canada, has been active in carrying out research projects to prove out the concept of applying fuelcell technology to underground mining vehicles. These have been carried out by a consortium consisting of mining companies, equipment manufacturers, technology developers, national laboratories and consultants, with the participation of Canadian and U.S. mine regulatory agencies. This clean technology, which produces only water and electricity, would allow several advantages to be obtained, in the health area (by eliminating diesel emissions and reducing noise generation), in lowering production costs (such as reducing ventilation required) and lowering green house gas emissions. This article outlines the results obtained in several key areas, such as the operation of fuelcells in underground conditions, risk issues related to underground and surface operation of hydrogen vehicles and hydrogen production and delivery systems, and the design and mining performance of the world?s first hydrogen mining vehicle, a mine production locomotive. The work to date on the fuelcell loader, designing the power plant and power transmission systems, operational requirements, and operating cost reductions, is also presented. There is also an evaluation of the overall mining applications and advantages this technology can bring to underground mining, including the facilitation of automation and tele-remote operation.

May 1, 2003

By Andre Vien, Jean-François Dupont

"Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the installation and use of such a device on a SAG mill at the Holt-McDermott Mine. Comparison to measured static volumetric load and bearing pressure and inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed. INTRODUCTIONWhile the measurement of load is very important in all kinds of grinding applications, the biggest benefits are expected from AG and SAG milling. This is what motivated Holt-McDermott to take a closer look at this problem, with a view to optimizing SAG mill performance.In many cases, the SAG mill control problem can be stated as maximizing throughput while avoiding a volumetric overload, with the other constraints (e.g. power, grind size, upstream/downstream equipment constraints, etc.) playing a less important role. This is certainly true at Holt-McDermott where the SAG mill is the production bottleneck about 90% of the time, and anything that can be done to increase SAG mill throughput will have a significant impact on operating profit.Although the goal of maximizing throughput while avoiding volumetric overload is simple to state, it has proven to be much more difficult to achieve. The mineral processing industry has expended a great deal of time and effort to devise control strategies in the pursuit of this objective. While much progress has been made, there is still room for considerable improvement. Across the industry it is probably fair to say that overloads occur relatively infrequently, but the real losses accrue as a result of the tendency to run rather conservatively."

Jan 1, 2001

By R. Haecker, S. Bajic, R. Thorpe, A. Palko, M. Kalstrom

"Historically, mineral processors have used inferential data like plant instrumentation, assays, and grind sizes to monitor the performance of their plants. The ability to monitor the minerals themselves on a daily basis has eluded all but the very largest and richest of operations. The advent of a new generation of compact, robust, and user-friendly SEM-based automated mineralogy systems looks set to accomplish this, aiming to bring daily mineral monitoring of plant performance within the reach of all mills from mid-size upwards. This paper describes the use of this machine at Greens Creek Mine, a 2.5 ktpd Ag-Au-Pb-Zn operation with a complex flotation flowsheet. During the trial, the machine provided turnaround from sample collection to reporting averaging 24-36 h for key daily samples. All equipment was located within the compact mill, and proved highly reliable despite the challenging environment. Turnaround time was fast enough for metallurgists to understand, and, where possible, respond to ore and process changes while they were still happening. The plethora of data generated was filtered to a simple report whereby mill management could quickly absorb key daily mineral-based performance indicators. This paper will describe how the data was used to understand the key drivers behind metallurgical efficiency at Greens Creek, and how metallurgists began using the information to enhance daily mill performance."

Jan 1, 2014

By Olli Aulio, Outokumpu Oy

"GENERALThe Outokumpu Company is today an important European producer of metals from its own mines: copper nickel cobalt, ferro chrome and zinc being the main products. In 1972 about 4 million tons of ore was hoisted from eleven mines.Outokumpu Oy has gained experiences on the various aspects of on line computer control since 1968. This knowledge has been combined to develop a standard computer control package for concentrator control. Before the development of computer control package was started Outokumpu Oy had three large computer control systems. The first system was at the Pyhasalmi Concentrator, thee second at the LokkolaPlant, and the installation of the third system at the Vuonos Concentrator was just started.The characteristics of general computer software packages - both control and executive ones - were thus well-known as well as the practical usage of control theory. Furthermore Outokumpu had developed the Courier analyzer which included a so-called minicomputer. This project had given experience both 1n totally self made real tire executives and in computer hardware and peripheral d=vices. The instrumentation of the Outokumpu concentrators was designed and installed traditionally by the engineers of Outokumpu themselves."

Jan 1, 1973

By J. E. Williamson

Introduction 1. Factors on Which the Design of the Roaster Plant was Based The roasting operation at Lake Shore, it was realized from the outset, would be profitable only if costs and losses could be reduced to a low figure. It was absolutely imperative that the operation should be self roasting over the whole range of tonnages and sulphur grades which might obtain during the life of the mine. The roasting operation could not bear the cost in fuel and labour of even a partially fired roast. To meet this requirement, it was necessary to resort to additional insulation in the construction of the roaster and to provide a more flexible means of rabble cooling than the conventional water jacket (see p. 31). A second basic consideration was that of handling a wet, putty-like concentrate. The operating costs of a drier ruled out the possibility of drying the charge before feeding it to the roaster. Moreover, the dusting which would result from charging a dry product virtually all -40 micron (325 mesh) in size would seriously handicap the use of a dryer. Dust lubrication (p. 3S) due to the back-mixing action of the Edwards rabbles, and the use of a Sullivan slapper ( p. 27) on the concentrate filter, completely solved the problem of handling the roast feed. The third consideration was the reduction of dusting to a sufficiently low point that a Cottrell or other dust collecting system was unnecessary. The Edwards roaster when properly supervised, it is believed, can be operated to give the minimum possible dusting. At Lake Shore, the evidence has been that less than 1 per cent dusting occurs at any time and that the greater part of the dust produced is recovered either in the spray tower or in the dust chambers.

Jan 1, 1947

By Karl J. C. Harries

"12.1. NO DEPRECIATION/GAAPAll calculations and computations relating to the Royalty shall be carried out in accordance with generally accepted accounting principles consistently applied to the extent that such principles are not inconsistent with the provisions of this Schedule and the agreement attached hereto, it being specifically agreed that nothing herein contained shall permit, or be construed to permit, the Operator to deduct any amount for depletion, depreciation, amortization or any deduction that represents a non-cash outlay.Comment: In cases like net profit royalties where recoupment of prior expenditures is permitted, care should be taken to avoid any implication that depreciation may also be taken. It is only logical and equitable that Property Owners should not be permitted an apparent ability to “double dip” with respect to deductions. A provision like this example should accomplish the task. It will be noted that the example specifically contemplates that the negotiated arrangements will prevail over any requirements of GAAP. Accordingly, if the parties agree to an unusual formula for recoupment, it will not be set aside to accommodate GAAP requirements. Under GAAP, revenues and expenditures are accounted for on an accrual basis. In addition, it specifically prohibits the taking of non-cash deductions, which is in keeping with the concept of recoupment.Although in some ways the example states the obvious and could be considered redundant, its presence, especially in provisions contemplating recoupment, makes it clear to the financial people that there may well be some variations from normal practices dictated by GAAP, while at the same time confirming the availability of GAAP to fill any voids.The accounting profession often makes the caveat that application of GAAP is an “art”, not a “science”. GAAP do not provide a cure-all and can create problems that will have to be addressed. For example, GAAP contemplate that asset costs are to be reduced by investment tax credits, which can cause a problem for a payor with more than one mine."

Jan 1, 2003

By H. E. Pawson

"COMMON METHODS OF ELIMINATION: The four methods most frequently used to dispose of cyanide wastes are:1. Oxidation2. Dilution with water or with cyanide free wastes3. Acidification and dilution of resulting gas with air4. Alkaline ChlorinationMost operators practice a combination of the first two methods, allowing oxidation and dilution of cyanide waste in tailings ponds. Then, pond effluent is introduced to a stream for further dilution andoxidation which is expected to take care of the cyanide. This method oftreatment does work to a certain degree. Atmospheric oxidation in tailings ponds and in receiving streams chemically breaks down the cyanide radical to form carbon dioxide and nitrogen.2(CN) + 202 2 CO2 + N2The monetary advantage to this method is obvious to the operator but too frequently though, climatic conditions are ignored. Length of winter, and reduced flow of the receiving stream in summer, adversely restricts the result of this combined method. For those of us who rely mainly on dilution it would be wise to remember that 70 million pounds of water are required to dispose of one pound of sodium cyanide (1).The third method outlined involves addition of acid in a closed vessel and venting resulting gas to atmosphere with or without air dilution by mechanical means. Cost, safety and some form of secondary treatment to complete destruction of cyanide remaining in the solution usually make this method prohibitive.The alkaline chlorination method is the one most commonly accepted for treating cyanide bearing wastes since it is felt that cyanide is completely eliminated in this manner."

Jan 1, 1973

By D. Kidby, A. Briggs

"Vitrokele ™ is a synthetic adsorbent, using chelating groups on large polystyrene beads, developed in Canada over 7 years ago, and first commercialised in 1985 to recover noxious metals from plating wastes.Pilot plant trials have been performed in Australia and Canada to demonstrate the recovery of cyanide and removal of metal cyanide complexes from gold plant effluent using Vitrokele1 M 912. The pilot plants comprise a simple adsorption train (similar to a CIP circuit) followed by complete elution facilities, so that loaded Vitrokele™ can be stripped and returned to the adsorption circuit.An account of these campaigns is provided, showing the reduction of total CN levels from over 200 ppm to less than 0.5 ppm and Cu levels from approximately 100 ppm to less than 0.3 ppm in treated tailings.Comparisons between pilot plant results and laboratory test data are given and probable future work on the process and its application to the gold mining industry is discussed.INTRODUCTIONThrough millions of years of evolution, life forms have developed specialised molecules with exceptionally high affinity and selectivity for various metals such as iron, cobalt, zinc and copper.In the early 80's professors at the Faculty of Medicine of McGill University engaged in research on the extremely efficient ways that living cells captured trace metals essential for life.As research progressed, it became evident that the special molecules used by biological systems to capture metals could be synthesized to capture selected metals with similar efficiency from water or other solutions.The technology was first commercialised in 1985 to recover noxious metals from plating wastes with compositions applying the special molecules (chelating groups) on vitreous particles (hence Vitrokele™). To date approximately three commercial Vitrokele™ plants have been installed for treating plating waters in Ontario and Quebec."

Jan 1, 1992

By D. M. Doyle

"The Strathcona Concentrator operations, the application of control systems in the crushing, flotation and tailing fill sections, and current and future computer control concepts are described in this paper.The computer has been used for reporting and monitoring roles and operating the on-stream analyzer since start up of the mill in 1968, while over the past twenty months, it has been used for process control. The systems which have been developed include:1. The blending of pentlandite concentrate with pyrrhotite concentrate to produce a special product of constant nickel analysis.2. The blending of cement with tailing fill to produce backfill of consistent cement content.3. The supervisory control of xanthate, frother and pH to the flotation circuits to maintain the nickel copper concentrate grade within narrow limits.IntroductionThe Strathcona Concentrator is currently treating 7,200 tons per day of an ore which contains nickel associated with the minerals pentlandite (28 -32% Ni) and pyrrhotite (0.3 -1.0% Ni). The ratio of the nickel minerals varies from 4 to 15 parts of pyrrhotite to 1 part of pentlandite over the orebody. The production of a high grade concentrate re4uires the separation of this small quantity of .oentlandite from the much greater proportion of pyrrhotite and gangue and is complicated by the presence of two pyrrhotite minerals differing in nickel content, floatability and magnetic susceptibility."

Jan 1, 1974

By R. A. Ozerkevich, R. J. Voisey

"SherrGold's MacLellan V ne is located about five miles south east of Lynn Lake immediately to the east of the Keewatin River. (Figure # 1)The property is accessible by an all weather road, leading north from the provincial highway 391, which links Lynn Lake with the Town of. Leaf Rapids and the city of Thompson to the south.The MacLellan Mine (formerly the Agassiz property) was discovered in the early 1950's and optioned from Comiesa Corporation in 1979 by Sherritt. SherrGold Inc. was formed in September 1985. Sherritt then transferred the MacLellan Mine, 15 other gold prospects in the Lynn Lake area and the old Lynn Lake nickel-copper mill to SherrGold. At the same time Sherrgold entered into a management agreement with Sherritt whereby Sherritt would develop and operate the MacLellan Mine and conduct SherrGold's exploration activities.The ore body as outlined in the original feasibility study is expected to produce in excess of 300,000 ounces of gold and 450,000 ounces of silver over the next 5 years. However the deposit is open to depth and exploration is continuing on and around the main zone and the many satellite deposits.The start of construction of the MacLellan mine and mill was scheduled to phase in with the closure of the Fox copper-zinc mine located 30 miles west of Lynn Lake. The majority of the employees from the Fox Operation were either employed at the MacLellan mine or relocated to Sherritt's Ruttan Operation."

Jan 1, 1987

By Marc D. Melker, Geoffrey R. Lane, Michael Jahraus

"The Cresson gold deposit is located in the Cripple Creek district of Colorado. The deposit is composed of volcanic intrusive rocks and volcanogenic sediments where gold mineralization is associated with veins and cavities within a diatremal breccia.The purpose of the current study was to:1. Determine the penetration potential of the Cripple Creek Breccia.2. Assess the relationship between penetration and gold recovery within the Breccia.Two methods were applied using a cyanide solution containing ultraviolet sensitive dye to elucidate pathways of penetration within the rock. The first involved stagnant soaking of twoinch square pieces within the solution. The second method involved column leaching of ~100kg of Breccia crushed to P80 12.7 mm (0.5 inch). Samples were selected at specified intervals to capture the penetration progress of the solution. Photomicrographs and image analysis were utilized to illustrate and quantify the degree of penetration.Results indicated that the maximum penetration for the Cripple Creek Breccia (85 to 97%) due to a porous and permeable groundmass, containing large non-porous lapilli fragments. In addition, ~90% of leachable gold was recovered with only ~50% rock penetration.INTRODUCTIONDye penetration studies were first developed at SGS-Lakefield Research for the purpose of determining the fluid penetration amenability of differing rock types. The method was to place a large rock or drill core in a pan with 1 to 2 inches of a pre-mixed, water based fluorescent dye. The sample was sequentially cut after prescribed time periods to reveal a fresh surface. The cut surface was photographed under long wave ultraviolet light, and the same piece returned to the dye and allowed to sit until the next prescribed cutting."

Jan 1, 2006

By George Chung

"The Iron Ore Company of Canada's Carol Lake Project is Located near the western boundary of Labrador, 960 air kilometers northeast of Montreal (Figure 1).The Concentrator operation was started in 1962 with a capacity to produce 7 million tonnes of concentrate per year. The bulk of the concentrate was pelletized at a 6 million tonnes per year pelletizing plant completed in 1963. The remaining concentrate was sold in the international market. The concentrator was first expanded in 1966 to 10 million tonnes per year capacity with the pellet plant also expanded in 1967 to match the increase in concentrate production. In 1973, the concentrator was further expanded to gear with the increase in concentrate sales. In 1977, more than 40 million tonnes of crude ore was processed to produce in excess of 17.4 million tonnes of concentrate and 10.4 million tonnes of pellets."

Jan 1, 1980

By Yaw Boadi, Andrew McCallum, Sandy Gray, Yavuz Atasoy, Peter Wemyss

"Various full-scale test programs and installations of the InLine Pressure Jig (IPJ) have provided evidence that pre-concentration of the difficult to leach sulphide mineral through gravity can provide significant increases in economic recoveries. The continuous gravity concentrates are intensively treated either by re-grinding or Intensive Cyanidation. Data from various mine sites worldwide is presented. Treatment of complex ore bodies with this low cost methodology may render previously uneconomic ore bodies financially viable and assist in the recovery profile of transitional ore.INTRODUCTIONThe use of gravity is made extremely attractive in complex ore situations due to the low cost of operation, typically a few cents per ton operating cost and lack of chemicals.Gold mines which suffer from poor recovery due to complex mineralogy such as Stibnite, Arsenic, Carbon, Telluride, Silver and other pacifying agents such as Iron, which can form coatings, can all benefit from the process proposed in this paper. The key issue is not overall recovery as much as one of economic recovery. The key to this is maximised recovery at the lowest possible capital and operating cost. Other options such as flotation are reviewed but are not seen in many instances to be the panacea due to issues discussed in the paper. The use of the InLine Pressure Jig in the re-circulating load of the milling circuit is a cost effective means of recovering a sulphide/gold concentrate containing the complex mineral assemblages which require re-grinding and intensive leaching for optimised gold recovery.The benefits of Jig Assisted Grinding (JAG) are many and the challenge over the past years has been developing, understanding, implementing and evaluating the benefits of various flowsheet models. This has involved the reconciliation of results in plant scale trials back to the original laboratory test program. The following paper outlines the insights gained in this area through extensive work carried out by many people across both laboratories and plant sites in Australia and overseas. The examples in this paper are some of the work carried out on a few selected sites but similar work has been carried out on other sites such as Penjom, Granny Smith and Agnew. This work has eventuated in several installations which we believe have great importance in the future of the gold processing industry. They will lead the way forward to the modern all-gravity plants of the future.Compared to flotation, for the recovery of sulphides, gravity is a simple option. The simplicity generally translates to low capital and operating cost."

Jan 1, 2004

By T. A. Grammatikopoulos, B. Vasily, A. H. Clark

"The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoeshaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York, no carbonate protolith is preserved, and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560°C, or, alternatively, 550 MPa and ca. 630°C.Several high-grade zones, averaging >40% but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 cm to 5 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates.St. Lawrence compares favourably to other known prospects and operating wollastonite deposits: having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production."

Jan 1, 2003

"The characterisation of resources and description of variability across different ore domains is key to accurate prediction of probable metallurgical performance. Such characterisation testwork often has limited drill-core from which to work and this immediately confines the characterisation method to smallscale. For flotation feeds, the JKMSI (Mineral Separability Indicator) is being developed as a potential characterisation tool, building on earlier work by Chudacek, (1990), which used shaken test tubes, and was called the EMDEE device. In addition, the consistency of flotation recovery for specified size fractions has shown to be preserved, irrespective of the amount of material in that size fraction obtained by different milling conditions, so that the overall recovery can be estimated from knowing the particle size distribution (McIvor and Finch, 1991; Bazin et al, 1994, Runge, 2007 and Wightman et al, 2010) The JKMSI unit uses less than 10 g of material per test in narrowly sized classes and results to date have demonstrated the value of the test. This paper discusses the potential of the test by demonstrating the link between JKMSI performance and mineralogy of five different ores from Laguna Seca, Escondida Minera Limitada as well as the correlation to plant scale performance obtained in an earlier survey (Coleman et al, 2006). Further work to tie down the proof of representatively of the small sample has been identified and is discussed and included in the paper. INTRODUCTIONSince the uptake of the flotation process at the turn of the twentieth century, small scale, laboratory methods have been sought to characterise flotation response. Although laboratory batch flotation tests are the most widely used method to evaluate reagents, characterise ore variability and obtain suitable model parameters using various scale up factors Runge (2101) other methods using less ore would be useful where ore samples were limited.A method using test tubes for testing ores’s flotation response to reagents was first developed by Ian Walk (Wark & Wark, 1935; Wark; 1938; Sutherland and Wark 1955). In these tests a 50 cc stoppered measuring cylinder served as a means for a qualitative experiment, the aeration being effected through violent shaking by hand. In these experiments about 10 g of mineral was ground by pestle and mortar under water after which the ground material was deslimed and adequately conditioned with the appropriate reagents."

Jan 1, 2013