Search Documents

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dumper operators are frequently exposed to whole body vibration (WBV) in surface mines. Surface mining activities involve the amalgamation of comparatively high intensity of vibration and extended exposure durations. Efficient risk reduction mandates knowing of important phases of a task that poses a threat to health of dumper operators. So far in India very limited studies have been reported on WBV exposure with regard to surface mines. This paper evaluates WBV of dumper operators based on ISO 2631-1:1997 Standards and European Union (EU) Directive 2002 for different phases of job cycle. Six dumpers were considered for this study and the vibration measurements were made for all the four phases of the job cycle by placing the triaxial accelerometer on the operator’s seat-surface and at the seat-back, independently. The findings of the study revealed that the haulage task (loaded travel and empty travel) remains the chief contributor to vibration exposure according to seat-surface and seat-back measurements. Maximum frequency weighted root mean square (RMS) of 1.12 m/s2 and 1.09 m/s2 were reported for empty travel task for seat-surface and seat-back measurements, respectively. For seat-surface measurements based on RMS, Z axis remains as the dominant axis of vibration for all the dumpers during haulage task, whereas for seat-back measurements, the dominant axis varies between X and Y. Exposure action value (EAV) based on RMS has exceeded the threshold value of 0.5 m/s2 for all the dumpers during loaded travel and empty travel for seat-surface as well as for seat-back measurements.

By Sarah Holtz Wilson, Kenneth Rossi, Carl R. Handford, David F. Tsztoo

The East Bay Municipal Utility District’s Claremont Tunnel is an 18,000-foot long water tunnel that crosses the Hayward Fault zone near Oakland, California. It was originally completed in 1929. This project involved the construction of a bypass tunnel through the fault zone, including an enlarged vault section designed to accommodate up to 8.5 feet of horizontal offset. Ground conditions encountered included sheared and crushed serpentinite and clayey fault gouge, and presented specific challenges for construction. A special excavation and support sequence used concrete-backfilled side drifts as foundations for the vault steel sets. It also allowed for a 20-foot-wide top heading and bench excavation in soft and squeezing ground conditions.

Jan 1, 2007

By Tae-kyeong Yeu, Cheon-Hong Min, Hyung-woo Kim, Sup Hong, Minuk Lee, Chang-Ho Lee

This paper concerns the optimum arrangement of the buoyancy module, which is used for stable dynamic motion and structure stability of the marine flexible riser. The main method of this study is simulation-based design using Genetic Algorithm (G.A) for optimum design and Multi-body dynamic for simulation. The marine riser connects the vessel and the seabed-tracked vehicle. The motion of the riser affects the motion of the vessel and the vehicle. In this study, a marine riser of the deep-seabed integrated mining system (Figure 1) is used. This riser has a strong effect on efficient transfer of minerals. So, the buoyancy module must be equipped to supplement problems of the structure stability and the dynamic motion. Positions and quantities of the equipping buoyancy modules are determined by the at sea experiment (Figure 2). But this method is not easy because the actual sea experiment is expensive, time-consuming and dangerous (Figure 3). Thus, the position and quantity must be determined by simulation-based design. The dynamic analysis models of the riser and the buoyancy module were built in the commercial software DAFUL. In the marine environment, factors affecting behavior are current, drag force, etc.

Sep 1, 2014

By Faruk Oksuz, Cary Hirner, William A. Rochford

Grouting is a frequently utilized remedy in the planning and implementation of ground improvement and tunnel rehabilitation practice. The state-of-art grouting application used for Chicago’s McCook Reservoir project offers a unique alternative to the tunneling industry for pre-excavation grouting as well as tunnel rehabilitation, rescue and post-excavation ground improvements. The McCook Reservoir project included a computerized grouting control and data collection system for a precise and highly effective groundwater cutoff in fractured dolomites. By using balanced and stabilized grout mixes, the effective permeability of the rock mass was reduced over two orders of magnitude to less than 0.1 Lugeon by installing a double line grout curtain. The stable grout mix designs allowed high pressure and effective grouting at depths up to 125 m (410 ft).

Jan 1, 2005

By M. J. Fairweather, J. R. Egan, W. A. Meekel

Cominco Metals, in cooperation with two Canadian Universities and the Government of Canada, is developing applications for column flotation in the treatment of lead and zinc ores. Plant scale results at Polaris and pilot plant studies of Sullivan, Pine Point and Red Dog ores show column flotation to have significant advantages over conventional mechanical flotation for lead and zinc cleaning. Results from these ongoing studies are discussed in relation to ore texture, mineral recovery, impurity behaviour, scale-up and control.

Jan 1, 1988

By F. Mendaña

The characteristics of the igneous and metamorphic bedrock, extra-hard and abrasive, of the Guadarrama Tunnels, a bi-tube project of length 28.4 km without any intermediate attack, are first commented upon. Next, a detailed discussion is given of the most relevant aspects of the performance of the four double shield type TBMs. The experience of this leads to various recommendations to be borne in mind in future designs of TBM having to work in rock of similar characteristics.

Jan 1, 2007

By L. Kulik, J. den Drijver

Rhenish lignite will continue to play an indispensible role in the energy mix of the German Federal Republic for a long time to come. The use of lignite for electricity generation, upgrading and, if necessary, as a raw material is geared to the long term. The holistic management of opencast mines underpinned by approval law in the long term and a stronger focus on man, the environment and nature contribute to the acceptance of the mines by the local population. The same is true of state-of-the-art lignite uses: as regards their operational flexibility, lignite-fired power plants are ideal partners for the expansion of renewables. It is along these lines that RWE is continuing its power plant renewal programme as planned. With a view to that which will be conceivable the day after tomorrow, RWE is researching future technologies today in order to meet objectives such as security of supply, profitability and environmental compatibility to the same extent in the long term. Another important contribution to acceptance is public transparency and communications as means to support approval procedures and the implementation of measures in all areas related to lignite mining and utilization.

Jan 1, 2011

By Don L. Deardorff

The Deserado Mine and transportation system is the fuel supply portion of the Bonanza Power Plant project. Deserado Mine con¬sists of an underground mine with a capacity of 1,224,700 tonnes (1,350,000 tons) of clean coal per year, a 649 tonne (715 tons) per hour closed water circuit jig type preparation plant, a 5.6-kilometer (3 ½ -mile) overland conveyor with covered slot storage, a unit train rail load-out and 59.5 kilometers (37 miles) of totally independ¬ent, captive electrified railroad. Planning and exploration started in March of 1978. Construction of all facilities was completed in April of 1984, approximately six years after initial planning was commenced. This paper will discuss exploration, environmental permitting, mine planning, engineering and construction of the Deserado Mine project.

Jan 1, 1984

By W. A. Wright

The use and abuse of social media restate common employee relations issues. Business solutions to these issues require advanced preparation. Employers should establish and enforce social media policies to guide their reactions to employees? social media posts that reflect on the employer and its business.

Jan 1, 2011

By William H. Pomroy

This report describes research leading to the design, prototype fabrication, and successful in-mine proof-of-concept testing of two improved stench fire warning systems for underground noncoal mines. The stench system, widely used in underground noncoal mines to warn of fire or other emergency suffers several serious shortcomings, including the toxicity of the odorant leading to debility in miners; reactivity of the odorant with iron oxide, resulting in unreliable warning because the odor may fade when transported long distances in steel pipe; lack of control over the rate at which agent is released into the air-stream, resulting in some work areas receiving unbearably high stench concentrations and other areas being missed altogether; lack of visual indication of system status, valve positions, or proper system operation; and excessively long stench transit times. In 1979, the Bureau of Mines, U.S. Department of the Interior, began research to upgrade the stench warning system. Two systems were subsequently developed which offer significant advantages over current systems.

Jan 1, 1984

By D. M. Carris

Since the Buffalo Creek incident in February, 1972, Federal and state environmental agencies have had the pressure on the coal industry in the Appalachian area to close the coal processing plant water circuits. In an attempt to comply with this requirement, Eastern .Associated Coal Corp. decided to install a vacuum disc filter system at its Kopperston plant to eliminate the tailings pond and reduce the amount of plant make-up water. It was recognized at the time that the plant static thickener tailings would be a very difficult slurry to dewater because of its unusually high clay content. The following is a case history of the Kopperston installation and the refinements Eastern has made in its vacuum disc filter operation to increase efficiency.

Jan 1, 1979

By J. Appleby

This paper reviews earlier in-plant testing at the Sidbec-Normines pelletizing plant at Port Cartier, Quebec, Canada. It describes the result of the more prolonged use of coke breeze during recent months and in addition, the effects of varying dolomite and coke additives upon the metallurgical properties of the pellet production have been studied. Mention is also made of some brief test work carried out to use peat moss as a carbonaceous additive to the pelletizing process and in particular the plans for future work in this respect. Earlier laboratory pot-grate test work had indicated that a production rate increase of between fifteen and twenty percent was a practical possibility, or alternatively that the plant could be run at design rating with significantly lower energy consumption. These energy reductions were of the order of ten to fifteen percent for fuel and main process fan power respectively. The physical and metallurgical pellet properties for both blast furnace and direct reduction furnace use were little affected by the production rate increases, and were actually somewhat improved when practicing maximum energy conservations. Pellet properties could be further improved by not extracting the maximum energy economy. Two phases of carefully controlled in-plant testing were run to assess the effect of energy conservation under plant conditions. These two phases of testing confirmed that an overall fuel saving of approximately fifteen percent could be realized, with a reduction in the Bunker C oil consumption of about forty-five percent, and a reduction in main process fan power of approximately ten to fifteen percent. The present scope of work is aimed at establishing the use of varying levels of coke addition up to about one percent under normal plant operating conditions.

Jan 1, 1980

By Warren H. Weisz

A cement, in the broad sense, is any substance which will cause various materials to adhere to each other. Clay was probably the first material to be used by man as a cement or binding agent. Water occurs in or is mixed with the clay to make it plastic, so that it can be formed in place. The sun and air remove the water from the clay and on drying strength is developed. The clays unless fired are not too resistant to water, therefore, their use is best when restricted to dry areas. Gypsum used as a cementitious material is not the subject of this paper, but its use dates back thousands of years. Gypsum mortars were used by the Egyptians in building such massive masonry structures as the pyramids. The Egyptian mortar consisted of a mixture of sand with burned gypsum (of an impure type of 81.5 per cent calcium sulphate and 9.5 per cent calcium carbonate) for the cementitious material. The burning of this type of cementitious material took place at relatively low temperature. These burning reactions will be covered later when the dehydration of gypsum is discussed. The setting of the partially dehydrated gypsum is considered to be crystallization from a supersaturated solution which deposits crystals of dihydrate (gypsum). In low water-content mixes, the interlocking of the needle-like crystals helps to produce higher strengths. Slaked lime made from limestone burned at higher temperatures (1648 F is generally considered as the calcining temperature, although under certain conditions incipient calcination will take place at 1250 F) is another early-period cementitious material. During slaking with water, a colloidal or amorphous hydrated lime is formed. When it is allowed to dry, it hardens and develops low strengths. On exposure to the carbon dioxide of air in the presence of some moisture, carbon dioxide is adsorbed and part of the calcium hydroxide is converted to calcium carbonate. Structures in which a lime mortar is used continue to grow in strength as this reaction proflesses. Hydrated lime has the disadvantage of not setting under water.

Jan 1, 1960

By D. Marcus

A methodology was developed wherein. the increase in compressive strength, mineralogical changes and pore water composition were all studied simultaneously as a function, of moisturized spent shale curing time. From these results the relationship between the nature of cementation process and the composition of pore water was established. Heavy metals were entrapped in the cementing constituents and the pore water became mainly a solution of alkaline sulfates. While the specific data are applicable only to the material studied, the methodology and general conclusions are useful for evaluating the environmental factors in spent shale disposal and expected leachates composition.

Jan 1, 1984

The support of the roof in coal mines remains a critical safety issue with 3 fatalities from roof falls in 2007 and 430 injuries from roof falls in 2006. A snapshot survey by the authors of room design and support details as well as unplanned falls of ground in the industry revealed some useful data concerning support use, seam details, fall dimensions, bolt lengths and spacing and the stand-up time.

Jan 1, 2009

By Albin E. Anderson

The PSM System has been available to the mining industry for nine years. During this time, many of the more than 160 Systems sold have been put to practical use and have provided the owners a handsome return on investment. In this paper, the author will briefly discuss how the System works and how it can be put to use in automatic grinding circuit control. Throughout, detailed consideration will be given to the many factors that can significantly influence how successful a specific application is.

Jan 1, 1979

By R. Maurice King

In the operation of today's large scale ore-processing mills, it is extremely important to have some way of making an objective evalu¬ation of the performance of the available flotation reagents. Attempts to do this may often result in inconclusive findings since the magnitude of the difference in the mill results for any two reagents is apt to be quite small compared to the variability introduced by the process and 'the analytical procedures used to measure them. In cases where two reagents give vastly; different mill results, evaluation becomes a simple matter and as such deserves no further attention here. A question of primary concern, however, is how a mill can go about evaluating the performance of two reagents which may, for example, give a difference of only 0.001% copper in the-tailings or of 0.2% in copper recovery. The casual observer may feel that such small differences may be of little importance, but in a mill-whose daily tonnage is between 30 and 40 thousand, these differences could mean a substantial savings. Before the presentation of an actual example of a reagent testing scheme designed for just this-purpose, perhaps a few minutes should be devoted to a review of some statistical methodology to be used later in the discussion.

Jan 1, 1964

By Robert Giglio

Looking back over the last 150 years or so, it is not hard to see that electricity has been a primary force in shaping human development. It has been a basic ingredient in our industrial revolutions that simultaneously improved the productivity, working and living conditions within our farms, factories, hospitals, offices and homes. Today, it has become an essential part of our daily life and our future. Amazingly, we keep finding new ways to use electricity to make our lives more safe, comfortable and productive. It is a great success story of human ingenuity, achievement and development. Demand for electricity The convenience and value of electricity has not gone unnoticed by consumers. According to the U.S. Department of Energy (DOE) (Energy Information Administration, 2009), electricity is the fastest growing form of energy in the world and during the next 20 years the world will likely consume twice as much of it as it does today. In 2008, almost 20,000 terawatt hours of electricity globally were consumed (Energy Information Administration, 2009). That is enough electricity to light up more than two million baseball stadiums or power more than 11 billion computers continuously for an entire year. The United States has the dubious distinction of be-ing the largest consumer of electricity in the world with enough power to provide each American with more than 3 kW of electricity ? that is about twice the power currently available to Europeans, eight times the power available to the Chinese and more than 25 times the power available to the citizens of India (American Coal Foundation, 2009).

Jan 1, 2009

By Scott Rosenthal, David Gilkey, Michael McGivern, Lorri Birkenbuel, Daniel Autenrieth, Ty Murphy, Hadi Aldossari

A safety climate case study was carried out at a surface metal mine where investigators administered the Liberty Mutual Short Scale Safety Climate Survey to 365–368 miners to measure safety climate in consecutive years. Following the baseline safety climate survey in 2019, Foundations for Safety Leadership (FSL) training was conducted with 81 middle to upper management employees at the mine site. Investigators found statistically significant differences in the pre vs. posttraining FSL assessment scores of the middle to upper management employees who attended the training. The follow-up safety climate evaluation was compared to baseline scores and revealed no significant improvement. The overall baseline company safety climate score of 76.38 increased minimally to 76.50 (p-value = 0.616). Investigators also evaluated differences in safety climate between the company’s three major divisions (operations, maintenance, and administration). Both years administration had the highest mean score and operations had the lowest mean score. The authors attributed the statistically significant differences found among the three major divisions to various dissimilarities in their work environments.

Aug 13, 2021

By Manoj Khandelwal, Minghui Liu, Jian Zhou, Kun Du

The waste rock and tailings backfill into the mined-out areas are the most effective method for solving the environmental pollution and surface disasters for nonferrous metals mines. In practice, the success and availability of backfill operations are dependent on the slurry fluidity and the strength properties of cement backfill. The transport of the slurry through the pipeline to the designated backfilling area relies on its eximious flow properties, while the appropriate strength of the filling body ensures the safe operation of the stope. In this paper, the effects of cement and aggregate types on the slurry fluidity and strength characteristics of cemented backfill are studied in detail, which are often ignored in other pieces of literature. Diffusivity is used as an indicator to evaluate the slurry fluidity. Various slurries whose concentrations ranging from 70%, 73%, 75%, 78%, and 80% are made with different aggregate ratios and cement-sand ratios are tested. It has been shown that slurry fluidity is inversely related to its concentration, but 78% is the “stopping point” for the deterioration of fluidity. The addition of rod-milled sand improves or worsens the cemented backfill (CB) strength depending on the amount of rob-milled sand. The uniaxial compression experiment results on 216 CB specimens produced by different combinations of influencing variables showed that CB specimens made from cement with superior mechanical properties have a higher uniaxial compressive strength (σucs). It has been also found that the effect of aggregate ratio on the CB strength is not singular, but works in conjunction with the curing time and the cement-sand ratio. The longer the curing time and the higher the cement content, the higher the CB’s σucs. To avoid the time-consuming and costly problem of obtaining the strength of the CB from indoor experiments, an SVR model capable of predicting the uniaxial compression strength of CB specimens is proposed, which is optimized by genetic algorithm (GA) and particle swarm optimization (PSO) algorithm. The results of the three performance indexes (MAPE, MSE, and R2) show the superior performance of the GA-SVR and PSO-SVR models and the agreement of the predicted results with the experimental results, which indicate that these two models can accurately predict the σucs of CB.

Feb 3, 2022