Search Documents

By Kazem Oraee

Falls of ground have historically been the main cause for fatalities in underground mines. Although recent advances in technology have reduced the number of such accidents, when failures occur they usually result in severe consequences. Risks of rock falls, use of heavy machinery and electrical apparatus, entry to confined spaces, working in noisy and dusty environments, and working on unstable platforms are some of the hazards in ground control operations. Managing these risks requires a management regime involving strict adherence to operational codes of practice and an enshrined culture of safety. These should be subsequently reinforced through active participation of management, systematic training, and stringent internal and third party auditing. Accident reports show that the major contributing factor in most rock fall accidents is the failure to adequately manage known risks due to the lack of a systematic process. OHSAS 18001 (Occupational Health and Safety Assessment Series) is an international occupational health and safety management standard specification to develop occupational health and safety at the workplace. This standard is intended to help mine operators control occupational health and safety risks. Addressing the requirements of OHSAS 18001 can be a complex and demanding task. A comprehensive guide for efficient and accurate implementation of this standard is provided in this paper. The discipline can be used to establish an accountable management system foreground control activities in underground coal mines. The paper also provides guidelines for preparing necessary documents, devising safety policies, procedures, performing risk assessment, and handling instructions. Finally, the paper concludes by providing a sound analytical basis in terms of the creation of a robust safety management system foreground control operations in underground mines. Full benefits of implementing an effective and systematic operational health and safety management system are illustrated. The procedure adopted and prescribed in this paper can be used in all underground coal mines where lack of appropriate ground control practices can create deficiencies in both safety and productivity.

Jan 1, 2012

A model was developed to facilitate secondary tailgate support selection based on analysis of over 100 case studies, compiled from two different surveys of operating longwall coal mines in the United States. The ALPS (Analysis of Longwall Pillar Stability) program was used to determine adequacy of pillar design for the successful longwall case histories. A relationship was developed between the secondary support density necessary to maintain a stable tailgate entry during mining and the CMRR (Coal Mine Roof Rating). This relationship defines the lower bound of secondary support density currently used in longwall mines. The model used only successful tailgate case history data, with adequate ALPS SF according to the CMRR for each case. This model facilitates mine design by predicting secondary support density required for a tailgate entry depending on the ALPS SF and CMRR, which can result in significant economic benefits.

Jan 1, 1996

By Peter Altounyan

The rate of decay of the energy from a hammer blow to a coal mine roof is related to the size and nature of the contacts between the rock being struck and its surroundings The use of this principle as a basis for testing roof condition in South African coal mines has been investigated under a SIMRAC funded project, with the objective of reducing the number of roof falls. ( I ) A prototype instrument having a simple numeric display related to the energy decay rate (the Acoustic Energy Meter) was constructed and used to carry out surveys at mines covering the range of coal mine roof geology and condition. The equipment was simple to use and provided excellent discrimination between visually intact roof and less stable conditions, once the normal/abnormal threshold had been established for a given site. Areas of potential roof failure were identified close to roof slips and igneous dykes, and confirmed in areas of visible deterioration. Directional stress effects on roof condition were also identified at some sites, with consistent differences in readings obtained depending on the direction of drivage. Repeat surveys also indicated areas where roof conditions were deteriorating with time. Based on the success of the prototype, a hand held version of the instrument. has been developed to a specification from Anglo Coal. This incorporates a simple 'traffic light' green / amber/ red display, making the device suitable for routine use by mine operatives This version is now undergoing trials at an Anglo Coal mine. It is concluded that the Acoustic Energy Meter shows great potential as a test instrument providing output which relates to the stability of the immediate roof.

Jan 1, 2000

By Andreas Hucke

For the roadway design in the German hard coal mining industry, an advanced combined planning system has been applied during the past 20 years. The German mining industry is working with single entry roadways system. After first longwall passage the roadways will be stabilised with side wall building material packages. Later this roadway will be used again for the second retreating longwall. The intention of the implementation of several different design methods for the planning of the roadways is to enhance the reliability of the results. On one hand the planning system uses numerical simulation and physical modelling in addition to analytical and empirical methods. On the other hand in-situ monitoring and analysis during the roadway development will be used to verify and calibrate the numerical and physical models. Especially before the implementation of new support elements in underground, this system is suitable and reasonable because the new support elements will be tested in the physical and numerical simulation prior to cost intensive underground tests. The interaction between the numerical and physical modelling in comparison with underground monitoring and analysis during development and the later use of roadways will be shown with some examples. The first example shows a rock bolted rectangular roadway which will be mined at both sides of the roadway. Different support and roadway building material package systems are investigated under various stress conditions. The results are utilised to optimise the roadway support and the roadway side package systems. The influence of different points in time of the installation of several support elements in a combined arch and bolted roadway is shown as another example. Two different types of support systems are compared within the physical models. These models are used as a base for ongoing numerical analysis and simulation to find out the ideal point of time to assemble the different support elements. The last example handles the influence of slickensides in the roof of arch shaped roadway on their stability. Different slickenside positions and densities are investigated and classified.

Jan 1, 2006

Historically, the selection of mining sequence for multiple seam conditions has been based on many factors other than ground control considerations and minimization of interaction effects. Today, numerous operations are finding themselves mining above existing or abandoned operations, some of which exhibit large scale caving, pressure arches and subsidence troughs. Development of design criteria for the upper seam that would alleviate damage due to lower seam interaction effects can contribute substantially to the safety and productivity of many mining operations. The primary objective of this re search has been to identify methods of improving ground control conditions in the upper seam when mining through either passive or active subsidence waves. These methods concentrate on improved ground control practices for the upper seam, rather than reducing the amount of subsidence in the upper seams by improved practices in the lower seam. Design factors such as pillar size, pillar and opening orientation relative to the subsidence trough, offsetting intersections, and different support methods have been studied for the upper seam in a variety of typical geologic environments. Analysis has demonstrated criteria for ameliorating negative interaction effects and facillitating design in the superincumbent seam.

Jan 1, 1986

By Ulrich Paschedag

The WESTFALIA group of companies developer and manufactures underground mining machinery for complete high-performance longwalls. WESTFALIA uses a state of the art electrohydraulic system as the most important component for the realisation of today's fully automated plow or shearer longwall. The shield control unit (SCU) allows maximum custom designed software flexiblity as well as maximum hardware reliability. The master control unit (MCU) monitors shield support data as well as the plow/shearer position. By using an industry standard PC in an explosion-proof box with an intransically safe keyboard nearly unlimited software capabilities can be obtained with inexpensive hardware. Among various other modes of operation this MCU allows the monitoring and recording of data which can be transmitted to a surface computer. Production and operational adjustments can be made by the mine management based on the MCU information. Statistical analysis of the distribution of roof pressure under various conditions is also possible. The WESTFALIA automation system PM-4 gives the operator maximum flexibility and helps the mine management to run their longwall more efficiently and safely.

Jan 1, 1994

By Slawomir Bock

One of the fundamental issues having a great influence on the safety of operations performed in underground mines is the support of workings which should assure their stability in a given geological setting and mining-technical conditions during the life of their use. The process of designing and planning support for roadways may use analytical and empirical, as well as numerical methods. In view of the rapid increase in the data processing capacity of computers and the development of more and more enhanced software for numerical modeling, it seems to be advantageous to use numerical methods in searching for design solutions ? especially in the case of non-typical mining and geological conditions and in cases that need to take into consideration a great number of factors. The assessment of rock mass quality is of basic significance in designing mine supports. Fractures, dividing the rock mass into blocks, have an essential influence on the stability of the rock mass and underground construction. This paper presents examples of the fundamental underground investigations on the rock mass conducted by the Department of Extraction Technologies and Mining Supports of the Central Mining Institute in Poland, such as: penetrometric tests, introscopic examination, laboratory testing of rock samples and ground penetrating radar. Moreover, this contribution also presents examples of applications of three-dimensional numerical modeling for the purposes of stress-strain analysis of the rock mass around mine workings and computer-aided support design by means of FLAC3D (developed by Itasca) and Cosmos/M (developed by Structural Research and Analysis Corporation).

Jan 1, 2009

By Tex M. Kubacki

In 2007, the University of Utah Seismograph Stations (UUSS) temporarily expanded its seismic monitoring network in Emery County, Utah, in response to the August 6 Crandall Canyon mine collapse that trapped six workers. In spite of this additional coverage, no seismic events were located in the area during a six-day period (gap) from August 8 to August 13. The Mine Safety and Health Administration (MSHA) ?Command Center Log Books? however, contain references to 16 instances of underground ?bumping? and ?bouncing? that occurred during the gap. When ground truth information provided by the log books is compared to the raw seismic data recorded by the UUSS network, the correlation offers insight into the chronology of mininginduced seismicity (MIS) in the aftermath of the collapse. The new research focuses on identifying and locating seismic events that occurred during the six-day gap using double-difference relocation techniques and correlating them with log book ground truth. Ten seismic events were identified in the vicinity of the mine during the six-day gap, ranging in magnitude from coda magnitude (MC) 0.5 to 1.4. Three of these events were amenable to location by double-difference techniques. The location of one of these events is directly confirmed by ground truth information from the log books. As a result of this new research, the accuracy of Crandall Canyon double-difference locations has been improved, and the number of events correlated with ground truth information has increased. The seismic events occurring in and around the collapsed area appear in two distinct sections of the mine?east and west of the center of collapse. It was originally reported that the post-collapse events occurred in episodic clusters. The first two episodes occurred to the east, followed in time by a cluster on the west, and then by a third episode on the east. With the addition of new events to the data set, this pattern is no longer as clear, although the events still occur in clusters. Only one MIS cluster was found to occur within the bounds of the minimum estimated collapse area (Pechmann et al., 2008).

Jan 1, 2012

By Anthony Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990?s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine?s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

Jan 1, 2007

Recent improvements are described in several techniques for ground control in underground mining. Promising methods for analysis and mitigation of rockbursts are discussed. Methods of assessing damage to underground excavations from repetitive seismic loading are reviewed. Analysis of mining-induced surface subsidence is discussed.

Jan 1, 1989

By Anthony Iannacchione

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width-to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By Mike Faure

Hercules cribs make use of timber loaded parallel and perpendicular to the grain. Maximum use is made of the orthotropic properties of timber resulting in crib- having superior strength, high initial stiffness and controlled post yield deformations. Blocks and timbers can be combined in many different ways resulting in thousands of different geometries. Each geometry has a specific combination of block on block, timber on timber and block on timber contact area which results in a unique performance. Each crib can be fingerprinted by defining four parameters relating to its load/deformation curve. If the geometry is known, the performance can be predicted with a high degree of accuracy. If the mine support requirements are known, the crib geometries can be designed which met theme requirements in the most cost effective manner Hercules cribs come closest to satisfying mine support requirements. Due to the flexibility of the concept and their superior strength, they can be employed in most mining situations to enhance safety, improve productivity, reduce working costs or improve profitability.

Jan 1, 1993

By Anil K. Ray

This paper discusses in situ studies conducted at an Illinois Basin room-and-pillar coal mine to evaluate the performances of three different types of bolts under similar geologic conditions. The bolt types considered were the fully grouted passive rebar (FGPR), the resin-assisted mechanical anchor (RMAB), and the fully grouted tension rebar (FGTR). During the evaluations, the three types of bolts were installed in a single entry covering a span of three contiguous pillars with almost identical geologic conditions. The performances of the three types of bolts were investigated by instrumentting the bolts prior to installation as primary supports on cycle. Additional data on roof behavior was collected with extensometers and shear meters placed near the instrumented bolts. Excluding some time lapse right after installation, the performance evaluation of the three bolt systems was based on the data collected for over a year. Based on this study, it was found that the axial loads measured in the different bolt types did not show any identifiable patterns under the prevailing geological conditions at the mine. Therefore, the assumption that active bolts must be superior to passive ones is not always valid. Even though the studied mine did not have any thinly laminated, weak rocks in the immediate roof, the passive bolts performed as well as the active systems.

Jan 1, 2012

By Andrew P. Schissler

The Citronen Zinc-Lead Project is one of the world?s largest undeveloped zinc-lead resources, containing more than 13 billion pounds of zinc and lead metal. The project is located in northern Greenland, a self-governed region of the Kingdom of Denmark (Figure 1). Citronen is the northern-most mine in the world, operating at a latitude of 83o 3? N. In excess of 67,000 meters of diamond drilling have been completed to delineate the resource. As of January 2012, the measured, indicated, and inferred reserves for the Citronen project totaled 70.8 million tonnes, consisting of 5.7% zinc + lead (3.5% zinc cut-off) (Ironbark, 2012). For the underground mine plan, room-and-pillar and long holestoping mining methods were selected. The beneficial application of structural fill was considered for increased recovery, efficient tailings disposal, and ground control. Three types of fill were compared - paste fill, cemented rock fill, and iced tailings. An environmental and economic feasibility study concluded that iced tailings was the preferred alternative provided it met the ground control requirements. The purpose of this paper is to explain the investigatory steps that led to the possibility for the use of iced tailings as structural fi

Jan 1, 2012

By Shu Yan

The high resolution resistivity method (HRRM) is developed specifically for detecting underground cavities and tunnels. HRRM has a special feature in that it can recognize and cancel static shift, which makes it different &om the high density resistivity method (HDRM). In searching for various means for detecting underground cavities, we found that the detecting depth of the transient electromagnetic field method (EM) depends mainly on the measurement duration, not the loop area. In addition, TEM can also be used to locate the high-resistivity bodies. In order to use them for local working site conditions, we combine HRRM with TEM to become a combined electromagnetic method. Since the late 1980's this method has been used to locate abandoned mines and air passages and burning centers of mine fires with great success. This paper cites case studies for which this technique was successfully used.

Jan 1, 2005

By Stephen C. Tadolini

PC-Strand tendons, commonly referred to as cable bolts, have become a major rock reinforcement device for underground mining and civil applications. The most common configuration is a 1+6 strand, which designates a center king-wire, with six outer wires wound around it to form a 0.6-in (15-mm) diameter cable. The capacity of this tendon approaches 30 tons, but the performance is largely dependent on the anchorage medium and the ability of the system to transfer stresses back into the rock mass while reinforcing and suspending the immediate roof. Recent developments to improve the transfer mechanisms of the PCstrand via the anchorage medium by impregnating the individual wires with uniquely designed deformations have resulted in improved anchorage and subsequent cable bolt performance. This paper describes a series of laboratory tests used to develop the initial indentation patterns and numerical modeling simulations that were undertaken to refine and optimize the final designs. The new, indented PC-Strands, offered in both bright and properly galvanized, have been tested in the field and are being used effectively in two new cable bolt products. The results of the laboratory, computer modeling, field testing and in-situ installations provide a glance at the next generation of cable bolts. This suite of testing shows how they will improve the safety and serviceability of openings under adverse ground conditions.

Jan 1, 2012

By T. M. Tharp

Attempts to analyze the stability of slopes, foundations and underground openings in discontinuously jointed rock have generally assumed full joint continuity or ignored the role of stress concentration at the tips of discontinuous joints. The most common approach in rock slopes is to consider a failure plane consisting of coplanar, but discontinuous joints separated by intact rock. The intact rock is assumed to fail in shear as a MohrCoulomb material and to contribute a strength component proportional to the fraction of the failure plane that is intact rock (Jennings, 1970). An alternative approach by Stimpson (1978) applies Lajtai's (1969) theory for shear strength of discontinuously jointed rock masses to slopes. Lajtai allows tensile failure in the intact rock of a composite surface. This theory yields lower shear strength than that of Jennings (1970) except in the presence of high normal compression, however it also fails to account for the stress concentration at the tip of a discontinuous joint. For a given slope geometry, stresses increase with slope height, but in both of these models rock mass strength is independent of size. A fracture mechanics analysis shows that particularly for small slopes, rock mass strength decreases with size.A continuous stepped failure surface produced by propagation of preexisting joints may develop at lower shear stress than pre¬dicted by the Jennings (1970) or Lajtai (1969) models. This fracture mechanics model applied to slopes in competent rock is more realistic in its assumed failure mechanism, and for large slopes more conservative than the Jennings (1970) or Lajtai models (1969).

Jan 1, 1984

By John Popovich

The MICON RokLok binder system including component and consolidation processes and safety and its first aide are described. The implementation procedures and selection of injection parameters are discussed. Finally a case example of recovering a 30-ft. long roof fall in mainline haulage entry is used to illustrate the economic potential of preventive measures by RokLok injection.

Jan 1, 2001

By M. M. Zarnan

This paper presents the results of s study involving characterization of ground subsidence of abandoned lead-zinc mines in northeastern Oklahoma. Two coordinated efforts were undertaken: (1) collection and analysis of available data such as driller's logs, geologic cross-sections, structure contour naps and stratigraphic sections, and (2) development of a numerical (finite element) technique for prediction of collapse and mine subsidence. An in-depth analysis of a major collapse in the region was conducted. The factors which contributed to this collapse were identified.

Jan 1, 1989

By G. J. Hasenfus

This paper presents the results of an extensive hydrological and geomechanical monitoring program which Gas conducted at a longwall coal mine in W. Va. The field program included monitoring of groundwater levels. overburden hydraulic conductivity, overburden movement, and surface subsidence relative to the passage of the longwall. Overburden geology and rock strength characteristics were evaluated prior to mining. A postmining corehole was drilled to evaluate main roof fracturing. An overburden response model is proposed based on the correlations between hydrological and geomechanical data.

Jan 1, 1988