Search Documents

By Robin B. Dill, Mark Pelletier, Daniel J. Dobbels, Subodh Bhaumik, Daniel J. VanRoosendaal

Although primarily cut-and-cover excavations are required for replacement of the existing elevated I-93 interstate highway through the heart of Boston for the Central Artery/Tunnel (CA/T) project, some mined tunnel construction was also undertaken. The mined tunneling conducted was the 22-m-wide northbound roadway structure which passed below a 20-m-deep operating underground subway station that was built in 1913. The innovative underpinning scheme used to support the subway station during construction resulted in the successful mining beneath the subway station with negligible vertical settlement. Two grouting galleries were carefully mined below the subway structure, and pre-grouting of the granulary, pervious glacial soils and weathered bedrock was carried out from these galleries. The reinforced concrete walls of the underpinning structure were constructed within three stacked drifts that were sequentially mined below each grouting gallery. After 11 cross adits were mined between the grouting galleries, cast-in-place post-tensioned girders that spanned between the stacked-drift walls were constructed to support the subway station. The stacked-drift walls also provided lateral support for the 22-m wide by 29-m long by13-m high opening beneath the girders.

Jan 1, 2001

Impala Platinum?s No.16 Shaft mine is currently under construction and is expected to reach full production of 256 500 tons per month by 2014. Mining will start at 1 260 m below surface with a maximum mining depth of 1 535 m where virgin rock temperatures of 56.6°C will be experienced. As a result of depth, high virgin rock temperature and narrow reef mining, an expected total of 31.5 MW[R] of air cooling capacity will be required to achieve acceptable underground conditions. This will be achieved by cooling mine intake air in a single dedicated air cooling installation located on surface. The compact installation includes air cooling spray chamber, refrigeration machines, condenser cooling towers, evaporator and condenser water reticulation as well as all electrical and control systems. Construction and commissioning of the first phase of this air cooling installation has recently been completed on a turn-key contract basis.

Jan 1, 2009

By N. S. Yet

This paper shall present the design and construction of bored pile and diaphragm wall for the proposed MHA complex in Singapore. The work was carried out by L&M Foundation Specialist Pte Ltd and PWD Consultants Pte Ltd was the consultant for this project. A brief description of the project is first presented to illustrate the scope and scale of the work involved, which includes the construction of bored piles and diaphragm walls and installation of steel stanchions in the bored piles. This is followed by a description of the methodology used to analyse and design the wall and bored piles. As both towers in this project are supported on bored piled foundation and are constructed by top down construction method, the analysis of the wall has taken into consideration the sequence of work phase by phase and this was carried out by means of a commercial finite element program called CRISP. Modelling of the problem will be briefly described and the findings from the numerical analysis will be presented. This is followed by a description of the structural and geotechnical design aspects of bored piles. The paper shall then describe the difficulties encountered for this project and solution used to solve the problem. The subsoil condition will be described with special mention on the encounter of very strong granitic rock at depth above the maximum excavation level of the basement at certain locations, hence necessitating the drilling of rock for a considerable depth for both bored piles and diaphragm wall. At this juncture, the construction method used to drill through the rock will be briefly described. For construction of bored piles, penetration of rock was carried out by chiselling or drilling using reverse circulation rigs. For construction of diaphragm wall, it requires the employment of Bauer hard rock cutter which uses cutting wheels fitted with roller bits and are capable of excavating into granitic rock of compressive strengths more than 100 MPa.

Jan 1, 2000

By Adrian Coombs

The York Durham Sewage System (YDSS) Interceptor Tunnel Project is located in the Town of Richmond Hill, Ontario, Canada, just north of Toronto. Construction commenced in September 2006 and completion is planned for early summer, 2008. The project involved public and agency buy-in of construction technologies and methods that minimized dewatering, design and construction of sealed shafts with jet grout break-in and out blocks in order that Earth Pressure Balance (EPB) mode could be maintained by the Tunnel Boring Machine (TBM) during shaft entry and exit. This paper will discuss the advances that were made possible through the opportunity to apply and test these technologies in order to accommodate the aquifer and artesian conditions present on this project.

Jan 1, 2008

By Frederick C. Rhyner

Drilled shafts have become an economical foundation choice for bridges in the northeast United States, especially when they can be constructed over water without the use of cofferdams. For the Boscawen-Canterbury Bridge over the Merrimack River in New Hampshire, an unusual design was used to avoid the use of cofferdams and avoid the need for pier caps at the waterline. This design used a pair of integral drilled shaft ? columns to form a bent type of substructure for support. Drilled shafts were 8-foot diameter, about 90 feet deep, with 16-foot long rock sockets. These are integrally constructed with 6-foot diameter reinforced concrete columns extending 37 feet from the waterline to the superstructure. Design load cases focused on lateral loads from ice flows, stream flows, wind and seismic events. Alternative analyses using different methods were made to check the design results. This paper discusses the subsurface conditions, design of the drilled shafts and columns, rebar and joint detailing issues, and construction of the drilled shafts.

Jan 1, 2004

By Andrew Peterson

The Maine Department of Transportation offered this challenging design-build project for a new, 12-span, bridge over the Kennebec River in Bath, Maine. This structure would be built to replace the existing Carlton Bridge connecting the village of Bath, Maine to neighboring Woolwich, Maine. The design build team of Flatiron Structures, Inc., and Figg Engineers, Inc., elected to design and build a segmental concrete bridge. Site conditions dictated that this bridge would be supported primarily on deep foundations. Case Foundation Company joined the project team in the winter of 1997 to install twenty-two, eight foot diameter drilled shafts. The drilled shafts were designed with 8' diameter, permanently cased shaft sections and 7.5' diameter rock sockets. Shaft lengths ranged from 20' long near the river's edge to 100' deep in the middle of the river. Rock socket lengths ranged from 12' to 30' deep. Two Osterberg Cell load tests were conducted on production drilled shafts. Figg Engineers utilized the results of the load tests to "fine-tune" the rock socket design during construction of the drilled shafts. Construction of the drilled shafts proved to be very challenging and called on every member of the design-build team to work together throughout the project. One of the most challenging aspects of this project was in the installation of the 8' diameter permanent casing and drilling of the rock sockets. Early in the project, it became apparent that the top of bedrock was broken and unstable. This condition limited the advancement of the permanent casing and the affect of a "seal" at the top of rock socket. As a result, as the rock socket was advanced, loose material spilled into the hole and stopped progress of the socket. In order to resolve this problem, the design-build team developed a redesigned drilled shaft which included the installation of a steel sleeve to seal off the unstable rock formation. Following installation of the sleeve, the rock socket diameter was reduced to 7' diameter and advanced additional length to achieve required design capacity. All drilled shafts were installed with equipment supported on floating barges. Water access, along with the long shaft lengths and very hard bedrock required the use of cranes and drilling equipment that far exceeded the requirements of typical drilled shaft projects. This paper will discuss the relationship between design, construction, and equipment utilization on this challenging design-build project. [ ]

Jan 1, 1999

By Gerald G. Griswold, Allan G. Provost

INTRODUCTION The Norad Expansion Project was located 10 miles southwest of Colorado Springs, Colorado, within Cheyenne Mountain. The expansion areas to be excavated would be adjacent to the existing underground Norad complex, which would remain in operation during the work on the expansion. The original complex had been constructed approximately eight years earlier and had been in full operation for approximately five years. Phase I, Excavation was awarded the Tiro Construction Corporation, a subsidiary of Harrison Western Corporation, Denver, Colorado, in the fall of 1970. Notice to Proceed was given to Tiro on 28 December 1970. The project owner was the U. S. Air Force, design was performed by the U. S. Corps of Engineers, Omaha District, who would also serve as the construction agency. [ ]

Jan 1, 1979

By Robert S. Thomas, Bernard M. Tarralle, Nasser Massoudi

"The Commonwealth of Virginia is restoring and expanding its Capitol of great historic significance. Designed by Thomas Jefferson in 1785, it is the second oldest Capitol building in the United States. The building expansion required excavations immediately adjacent to its South Portico. The building, which rests on shallow brick footings, is very sensitive to any disturbance caused by construction and excavation. A comprehensive and secure plan of operations was devised by the design team to ensure that this national monument remains unharmed by the new construction. Various construction techniques were implemented to satisfy the strict movement goal of 0.25 inch and distortion of U2000. They consisted of jet grout columns to stabilize the upper soils, compensation grouting for future foundation leveling, a tied-back reinforced concrete diaphragm wall for excavation retention and foundations, and realtime instrumentation for monitoring. This paper describes the design approach for the retention system, providing information on the various construction phases and techn iques, and reports on the movements recorded by the real-time monitoring system during the course of the project. At the time of this manuscript preparation, and the deep excavation complete to final grade, the results indicate that the extremely restrictive building movement criteria have been met. The success can be credited to detailed design, close cooperation among the project team, prudent construction methods, and real-time monitoring. INTRODUCTIONThe Commonwealth of Virginia is undertaking a comprehensive renovation and expansion of the Virginia Capitol building located in Richmond, Virginia. The Capitol building was designed by Thomas Jefferson in 1785, with construction of the original building starting the same year. The Capitol building was designated a National Historic Landmark in 1960 and was listed on the National Register of Historic Places in 1966.A part of the comprehensive renovation and expansion of the Capitol is a 25,000-square foot, two-level subterranean extension on the south side of the Capitol building, which will serve as a new Visitor Center and public entrance for the Capitol. Deep excavations were required for the construction of the new Visitor Center. The excavation required a permanent retention system to accommodate an approximately 40- foot deep excavation."

Jan 1, 2005

By J. Chae, D. Pecha, R. Andrews

The Henderson/ML King CSO Project is a major combined sewer overflow (CSO)reduction project for the Department of Natural Resources and Parks of King County, Washington. The central element of the project is the 3100 lineal feet long, 14'-8"diameter 42nd Ave S Storage/Treatment Tunnel. During the course of the project, the owner and consultants evaluated numerous elements of the tunnel including the alignment, geotechnical conditions, tunnel liner, and settlement monitoring requirements. The contractor utilized innovative shaft construction methods for the tunnel portals, and adhered to strict contract requirements in successfully constructing the tunnel. This paper provides an overview of the design and construction elements of the 42nd Ave S Storage/Treatment Tunnel that led to the successful completion of the project.

Jan 1, 2005

By David R. Beadman

This paper discusses how modern techniques of design and construction were used to create the deep stations for the Copenhagen Metro. The deep stations are located in small squares within the city adjacent to many old and sensitive buildings. The architectural design provides a large open atrium to allow natural light to reach the column free platforms to give the citizens of Copenhagen a feeling of safety and security and encourage them to use the Metro. The design and construction contract was undertaken using the relatively new and untried Eurocodes. The resulting stations set new standards of design for underground metros and have pushed forward the frontiers of what is appropriate construction practice to protect the existing and enhance the future environment.

Jan 1, 2000

By Hemang Desai

A damaged outlet pipe beneath Lenihan Dam has restricted reservoir discharges, severely constraining the owner?s groundwater recharge program. The solution, a new outlet pipeline through the dam?s right abutment, includes an approximately12.2-m-deep (40-ft-deep) shaft and 618.7-m-long, 4.3-m-diameter (2,030-ft long, 14-ft-diameter) tunnel mined in Franciscan melange composed of hard blocks of rock and soft clayey matrix. Alternating road header with drill and blast operations and using steel ribs and shotcrete have proven a flexible combination for handling the variable ground conditions. Excavating the shaft and connecting it to the tunnel require lowering the reservoir for five months, during which time careful construction sequencing and use of a tunnel plug eliminate the risk of an uncontrolled discharge.

By Alain Pecker

The choice of a design concept for a bridge foundation is guided by various factors; several of these factors are indeed of technical origin, like the environmental conditions in a broad sense, but others non technical factors may also have a profound impact on the final design concept. The foundations solutions adopted for the Rion Antirion bridge are described and an attempt is made to pinpoint the major factors that have guided the final choices. The Rion Antirion bridge is exemplar in that respect: the foundation concept combines the simplicity of capacity design, the conceptual facility of construction and enhances the foundation safety. The design of these foundations was a very challenging task which required full cooperation and close interaction with all the parties involved: concessionaire, contractor, designers and design checker.

Jan 1, 2005

By D. Rendini, R. D. Gutridge

INTRODUCTION Gwinnett County, Georgia, is a part of the rapidly expanding metropolitan Atlanta Georgia area. Located approximately 48 km (30 miles) northeast of Atlanta, Gwinnett County has a current population in excess of 600,000 and is projected to reach a population of 1,200,000 by 2025. As a part of the County’s master plan to supply drinking water for the expanding population and to increase system reliability, the Gwinnett County Public Utilities Department undertook the Shoal Creek Raw Water Intake and Pump Station Project. Figure 1 shows a vicinity map for the project. Prior to construction of the Shoal Creek Raw Water Intake and Pump Station Project the County had a single raw water intake to feed water from Lake Sidney Lanier (Lake Lanier) into a filter plant for processing into potable water. This project together with a newly constructed water filter plant provides Gwinnett County additional capacity and system redundancy to prevent interruptions to the drinking water supply. Lake Lanier is a man made reservoir with over 800 km (500 miles) of shoreline and was constructed by the Army Corps of Engineers in the 1950s for hydro electric power generation, flood control, and navigation benefits for the Chattahoochee River. Over time, Lake Lanier has become an increasingly important source of drinking water for the metropolitan Atlanta area. This paper focuses on the primary underground construction and lake tap components of the project including a 42.7 m (140 ft) deep pump station shaft 24.4 m(80 ft) in finished diameter transitioning to a 6.1 m (20 ft) finished diameter shaft, a3.05 m (10 ft) finished diameter by 19.8 m (65 ft) deep intake shaft constructed in an average of 21.3 m (70 ft) of water, and a 190.5 m (625 ft) by 3.05 m (10 ft) finished diameter modified horseshoe tunnel connecting the two shafts. This raw water intake system, in conjunction with the incorporated pump station with 8 pumps and dual1,829 mm (72 inch) pipelines, provides a system capacity of 1,091,062 m3/day(240 MGD) to two water filter plants and is expandable by the addition of pumps to1,500,210 m3/day (330 MGD). Parsons provided design and construction management services for the project. The $29.6 million contract to construct the project was awarded to W.L. Hailey &Company. Notice to proceed was given August 6, 2001 and substantial completion was achieved on January 20, 2004. Value engineering changes adopted for the project contributed to completing the project at a final cost of $28.8 million.

Jan 1, 2005

By Patrick O. Shires, Harry W. Schnabel

With stable building sites becoming scarce in the greater San Francisco Bay Area, the new Summit Senior Care Facility is being built into the side of an unstable hillside adjacent to the San Ramon Regional Medical Center in San Ramon, California. This hillside has had a long history of instability and the site of the new Senior Care Facility required excavation into both a historic old landslide and a more recent active landslide. After a thorough geotechnical study, it was concluded that the best way to build the new facility would be to construct a tied-back retaining wall in the area of the old landslide, since it extended off-site onto two adjacent properties, and remove the active landslide and replace it with compacted fill before cutting into its toe area with an additional tied-back retaining wall. The design was further complicated by the proximity of the site to several active faults. In the area of the old landslide, the combination of an ascending slope behind the wall, landslide forces and seismic forces resulted in total design pressures between 365 to 4,575 PSF for a wall with a maximum height of 30 feet. The wall for the old landslide was constructed by first drilling and placing steel soldier piles in concrete. The tip of the soldier piles extended a minimum of 12 feet below the landslide plane that was up to 36 feet below the bottom of the wall. Permanent double corrosion protected tiebacks were then installed through the soldier beams and anchored below the slide plane. A shotcrete facing was then installed on the face of the wall. BACKGROUND The site of the Summit Senior Care Facility is located on the southwest flank of Mount Diablo adjacent to San Ramon Valley which is characterized by gently rolling hills. The San Ramon Valley Regional Medical Center, which opened in 1990, is located to the north and an existing church is located to the southwest. There are also private residences located to the southeast. The site is shown in Figure 1. Numerous faults run close to the site, the most significant of which are the Calaveras and Pleasanton faults. The site has also had a long history of slope instability and has been the subject of numerous investigations. Studies conducted in 1979 and 1984 concluded that there was a landslide in the area and recommended that a buttress shear key be constructed between the subject site and the existing church for a sewer main as well as removal and replacement of the head area of the old landslide to stabilize the hospital site. While two previous geotechnical studies in 2008 and 2016 identified slope instability, they did not recognize the genesis and limits of the old landslide on the western portion of the site or the limits of the active landslide on the eastern portion of the site.

Jan 1, 2018

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shaft (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, ? Design and construction of the scour protection for the two main pylons, ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2005

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shafts (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, including the post-grouting of all drilled shaft tips. ? Design and construction of the scour protection for the two main pylons. ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2007

By Sivilay Sayavong, David Puller, Julian Gatward, David Hard, Martin Stanley

"AbstractThe Thames Water Tideway Tunnels programme involves the upgrade of London’s combined sewer and storm water system. The first section is the Lee Tunnel between the Beckton Sewage Treatment Works (STW) and the Abbey Mills Pumping Station. This will intercept the overflows currently discharging to the River Lee and has the capacity to store and transfer 350,000m3 of storm water and sewage. The project required 4 shafts and a 6.9km 7.2m diameter tunnel. The shafts are some of the largest ever constructed in the UK, with diaphragm walls up to 98m deep and 1800mm thick. As a result of the innovative methods of diaphragm wall design and construction adopted the 4 very large and deep shafts were able to be excavated and completed safely, with minimal water ingress and with extremely high quality.MVB, a joint venture of Morgan Sindall, Vinci Construction Grands Projets and Bachy Soletanche are delivering the £635m contract with Thames Water’s Project Management Team in a collaborative manner under an NEC contract. Mott MacDonald, Morgan Sindall UnPS & Bachy Soletanche are acting as designers.Some of the important advances in diaphragm walling made included:??Diaphragm wall design to both EC2 & EC7 taking into considering the assessment of chalk stiffness, high hoop stresses, large multiple openings and non-axisymmetric loadings.??Formation of shafts as a faceted circle from a series of overlapping panels, with primary panels up to 7.2m wide demanding concrete volumes up to 1300m3 be poured in one go. Overlapping secondary single bite panels cut into the grade C50/60 concrete.??Excavation of the full geological stratigraphy of London making bentonite management complex.??Panel verticality of 1:300 required over the full depth. The results achieved this and in many cases exceeded expectations with some panels coming in at up to 1 in 800 with the majority at 1 in 400 to 1 in 500. The project is also the first in the Soletanche Bachy Group to take data from the ultrasonic drilling monitor used to check the verticalty in electronic format in order to create 3D CAD as-built drawings.??Each diaphragm wall panel was reinforced over its full depth. Up to 18 separate pieces of reinforcing cage had to be installed in primary panels. Cages underwent a full range of temporary works designs to check that lifting, splicing and placing could all be undertaken safely. Fibreglass was used in the tunnel portals in the shafts to ease breakthroughs."

Jan 1, 2014

By R Blair

The Domain and Burnley Tunnels, which are major features of the Melbourne City Link Project, are MelbourneÆs first road tunnels. They are 1.6 km and 3.5 km in length respectively and are being constructed through a variety of ground conditions. Deeper sections of the tunnels have been driven through the Silurian mudstone which underlies Melbourne. Other shallower sections of the tunnels pass through a variety of ground conditions including silts, sands, clay and rock and have been constructed using both top-down and bottom-up cut and cover construction techniques. The Yarra River Crossing is a 140 m length of the Domain Tunnel which crosses under the Yarra River on a relatively shallow alignment. The crossing of the river using cut and cover techniques was identified in the early stages of design development as being one of the most challenging stages of the works on the Southern Link. The prevalence of varying geological conditions combined with the need for maintained traffic and stream flow conditions provided a demanding and often conflicting set of criteria for which there appeared to be no one clear solution. A team of designers, constructors, estimators and specialist contractors were involved in a concept evaluation and risk analysis study spanning a period of approximately 12 months. During this study, four concepts were considered as likely contenders. This paper provides a brief outline of the four concepts addressing their relative merits, disadvantages and risks followed by a detailed description of the adopted solution, namely top-down construction using secant pile walling (east bank) and bottom-up in situ construction (west bank).

Jan 1, 1999

By Suk han Jang

This paper describes the tower foundation design and construction experience for the 345kV Youngheung marine transmission line, which has been in commercial operation in Korea since July, 2004. This transmission line was designed and constructed to meet the rapidly increasing power demands of metropolitan areas and supply stable, bulk electric power from the Yonghung thermal power plant into metropolitan areas. This transmission line passes over the west sea, Lake Sihwa and over land. In order to successfully complete this project, and to safely support the tower during severe maritime conditions, several types of tower foundation such as Pad and Chimney foundation, Pier (Cylindrical) foundation, R.C.D foundation, Jacket pile foundation and Steel pipe pile + concrete mat foundation were developed and used. As the world?s first and longest marine transmission line, the 345kV Yonghung marine transmission line operates successfully, thanks to several high-tech civil engineering technologies and KEPCO?s accumulated experience.

Jan 1, 2007

By James W. Marold

Tunnel and shaft plugs have been designed to assist in construction of new and rehabilitation of existing tunnels and shafts. Tunnel plugs have been used to provide construction access for side by side tunnels, separation of raw and treated water, and to allow operation of one tunnel during construction of a nearby tunnel. Shaft plugs have been used to seal up surface openings to tunnels and to prevent seepage of water to the surface through adjacent tunnels or shafts. The design construction details of tunnel and shaft plugs are provided. Typical examples of tunnel and shaft plugs are provided.

Jan 1, 2008