Search Documents

By F. W. DeVries, O. B. Mathre

Addition of Kastone® peroxygen compound and formaldehyde to cyanide gold extraction process effluents, containing at least 5 mg soluble copper per liter, will oxidize acid-dissociable cyanide to levels less than 0.2 mg per liter, without appreciable oxidation of thiocyanate. Most of the copper precipitates and is removed by filtration of the treated solutions. The treatment can be completed in less than 2 hours when the excess of hydrogen peroxide over the cyanide is about 75-100 mg per liter. The excess hydrogen peroxide destroys residual formaldehyde and then is catalytically decomposed by the copper-containing solids that separate, so it will not interfere with subsequent operation. A pilot plant using this technology has been operated for more than four months at rates from 1-2 gpm. Clear, filtered effluent containing less than 0.2 mg acid-dissociable cyanide per liter has been produced.

Jan 1, 1981

By M. Drozd, A. Ibrado, P. Butcher

While effective in treating refractory sulfide ores, pressure oxidation leaves carbonaceous matter unscathed and able to adsorb gold from cyanide solutions. Barrick Goldstrike's strategy to mitigate this problem is to minimize contact between dissolved gold and native carbon in advance of the carbon-in-leach (CIL) process. Measures currently in use include limiting carbonaceous matter in the plant feed by meticulous blending of ore, controlling the degree of oxidation in the autoclaves and blinding native carbon surfaces with lauryl sulfate. The presence of residual cyanide and thiocyanate in the process water remains to be a cause of premature gold dissolution and loss of gold by adsorption on carbonaceous matter. This cyanide is introduced by water that is recycled from the tailing pond. Of several treatment options considered, oxidation by peroxymonosulfuric acid, also known as Caro's acid, is deemed to be the most effective. Laboratory and pilot plant tests show that Caro's acid can oxidize free cyanide, weak¬acid-dissociable (WAD) cyanide and thiocyanate, resulting in significant improvements in gold recovery downstream. The process requires Caro's acid at 125 % of the stoichiometric requirement and pH in the range of 9.5 to 10 to accomplish the desired destruction in about twenty minutes. A cyanide destruction plant is currently being designed and construction should be completed by the end of 2005.

Jan 1, 2005

Beatrix Gold Mine, a deep-level gold mine in the Free State province of South Africa, has the highest methane emission rate of any gold mine in the country. Methane is emitted from underground sources intersected during mining operations and is liberated into the general mine atmosphere. The total methane emission rate for the mine is of the order of 16001/s and the South section of the mine emits approximately 10001/s of methane gas. The mine has a history of gas accumulations which have led to a number of underground explosions. Following the last explosion in 2001 and the subsequent investigation, a number of recommendations were made. Two of these were to consider extracting the underground mine methane to render the mine atmosphere safe, and to declare hazardous locations that require special operating procedures. A number of such workplaces have now been declared at the South section of the mine. Methane gas is a potent, explosive greenhouse gas whose contribution to global warming and climate change is 21 times higher than that of carbon dioxide. To reduce its inherent danger and to mitigate its global warming impact, a carbon credit project under the Clean Development Mechanism (CDM) of the Kyoto Protocol has been developed and implemented, the aim being to capture and destroy the methane at Beatrix mine. The mine has constructed an extraction system to capture and extract 400 (Is of the methane. Percentage methane (per volume) of the gas intersected at source is 85%, with negligible concentrations of other hydrocarbons and water associated. The mine contracted the services of Group Five to design and construct the flare and ancillary equipment on surface, and Promethium Carbon was contracted to assist with the carbon¬-related aspects, approval framework, and administration of the project. A number of design and construction challenges had to be faced to extract and transport the gas effectively to the surface of the mine as the emitters are approximately 3 600 m away from the mine shaft at a depth of 860 m. Further considerations were the requirements for the type of column to be used to transport the methane gas, the pressure loss over the system, the safety systems needed to address the risk factors involved in the transport of the methane gas, and a suitable pumping system to extract the gas to the surface. The system operates under negative pressure provided by two blowers on surface delivering the emissions to a flare capable of burning off 450 8/s of methane gas. In this paper a number of benefits for the mine are discussed. These include, but are not limited to, the removal of approximately 55% of the total volume of methane gas from the general body of the air in the geographical areas of the mine where the methane gas is emitted into the atmosphere, and reducing the risk of methane-related incidents. A further benefit of this project is the mitigation of the global warming impact of the methane gas and the reduction of the mine's carbon footprint by approximately 25%. This project could also assist in alleviating the energy shortage being experienced in South Africa by means of the planned generation of 4 MW of electrical power, utilizing the methane gas, as a second phase of the project.

Jan 1, 2011

By N. Hmidi, T. Yalcin, M. Papadakis, B. Hilscher

Mill tailings, containing iron sulphides in particular, pose an environmental concern since they constitute a potential source of acid mine drainage which can damage vegetation, harm soil and living organisms, and contaminate groundwaters. Proper disposal of acid generating tailings is therefore an important issue that must be addressed and resolved in a satisfactory manner. Placer Dome Canada operates a 4000 t/d gold cyanidation facility at Musselwhite mine, in northwestern Ontario, where the mill tailings have been classified as acid generating. This study was conducted to explore the effectiveness of froth flotation in removing the sulphide minerals from these tailings and producing a low-sulphur, non-acid generating material that could serve as a capping material for previously deposited tailings. Laboratory semi-batch flotation tests were carried out in accordance with an experimental design procedure, and a computer simulation program was developed to facilitate the evaluation of flotation performance. In this investigation, pH, collector concentration, and airflow rate were considered as the relevant flotation variables, and their effects were examined both experimentally and by simulation. Results have demonstrated that flotation can successfully desulphurize the Musselwhite mine tailings and render them non-acid generating.

Jan 1, 2004

By Khaled Morsy

In the past two decades, high horizontal stress has been attributed to many ground control failures. Most believe that entries parallel to the high horizontal stress is most stable and least stable when perpendicular to it. Entry stability decreases when the angle between entry and horizontal stress increases. The concept of 2-D stress shadow has been proposed for selection of proper panel orientation, often with mixed results. In this paper 3-D finite element modeling was used to analyze the stress distribution at the headgate of a longwall panel subject to high horizontal stress at various angles. It was found that the directions of induced principal stresses at the longwall face and headgate are independent of the panel orientation. The induced principal stresses concentrate or relief at headgate based on the panel orientation with respect to the directions of the induced principal stresses. Accordingly, only 3-D modeling can fully account for the effects of high horizontal stress on panel orientation. The paper illustrates in details the changes in orientation and magnitude of all three principal stresses around the longwall face and T-junction area as panel orientation changes.

Jan 1, 2006

By J. Kendall Hales

Jan 1, 2005

By Gloria Fernández

La contaminación por drenaje ácido de mina se considera como la responsabilidad ambiental y económica más grande que actualmente enfrenta la industria minera. En ese sentido, se delimita las áreas afectadas mediante la perforación de pozos de monitoreo a través de un estudio geofísico previo. Por ello, el presente trabajo señala los métodos geofísicos como herramientas que pueden ayudar a delimitar y mapear las zonas afectadas por la contaminación proveniente de drenaje y filtraciones que va desde canchas de relave, pilas de lixiviación a minas abandonadas, etc.

Aug 25, 2002

By Y. H. Alghamdi, A. D. S. Gillies

"INTRODUCTION Background Diesel Particulate Matter (DPM) has been a critical issue during the last decade in underground mines. This problem is threatening the health of mine workers, as well as the mine’s productivity. It has been confirmed that the diesel engine exhaust is the main source for the diesel particulate matter (DPM), and that it has the highest impact in raising carbon monoxide, carbon dioxide, oxide of nitrogen, and hydrocarbons in the underground environment. Miners who are exposed to this kind of emission are at high risk for developing lung cancer and other lung diseases. The Mine Safety and Health Administration (MSHA) has issued standard rules to regulate diesel emissions in underground mines. The final ruling confirmed in 2008 that the total carbon should not exceed 160 µg/m3. (MISHA, 2008) Monitoring DPM in underground mines has become important to ensure compliance with the MSHA regulations. There are many different types of DPM monitoring systems that are currently being used in underground mines. Two methods are typically used for DPM sampling: the personal sampling method or the direct exhaust sampling method, which takes a direct sample from the engine’s tailpipe. Many mines do not recommend using the direct exhaust sampling method since it involves complex measuring equipment and procedures, as well as it is not regulated in the United States or Canada. Thus, the personal sampling method is the preferred method in many mines when taking DPM samples. Even this method includes many variations, such as the Respirable Combustible Dust (RCD) method and the method devolved by the National Institute for Occupational Health and Safety NIOSH 5040. The NIOSH 5040 method is the preferred method overall because it gives more accurate measurements compared to the other methods. This method does not allow organic carbon sources other than those coming from diesel engine exhausts to interfere with the measurements, which otherwise would lead to overestimating the actual amount of the DPM in the mine environment. An impactor feature in the cassette, which holds the samples in the instrument, characterizes this method. Since the diesel particles are less than 0.9 micron, this impactor does not allow particles more than 0.9 microns to be collected in the cassette filter. The cassette is then analyzed in a lab and the concentrations of organic carbon (OC), elemental carbon (EC), and total carbon (TC) are determined. Lately, the National Institute for Occupational Safety and Health (NIOSH) has developed a new instrument that can use the same concept of NIOSH 5040, but with instant measurements of elemental carbon. It utilizes laser radiation with the cassette so it can give a real time measurement. The real time measurements give instant information about the underground environment that will allow the mining engineer to take immediate action and enact plans instead of waiting for results from the laboratories where NIOSH 5040 method may take several weeks to get the measurements."

Jan 1, 2016

When xanthates or dithiophosphates are used as collectors in sulphide ore flotation, adsorbed species may be identified by gas chromatography of the volatile products formed during low temperature pyrolysis. For collector additions ,as low as 20 g/tonne of ore, pyrolysis of the flotation products usually gives' an olefin directly related to the particular xanthate or Aerofloat reagent used. The method is able to provide valuable qualitative and quantitative data relating to the extent of collector adsorption and the resulting changes in the hydrophilic or hydrophobic nature of the mineral surface.

Jan 1, 1974

By Shu Yan

The high resolution resistivity method (HRRM) is developed specifically for detecting underground cavities and tunnels. HRRM has a special feature in that it can recognize and cancel static shift, which makes it different &om the high density resistivity method (HDRM). In searching for various means for detecting underground cavities, we found that the detecting depth of the transient electromagnetic field method (EM) depends mainly on the measurement duration, not the loop area. In addition, TEM can also be used to locate the high-resistivity bodies. In order to use them for local working site conditions, we combine HRRM with TEM to become a combined electromagnetic method. Since the late 1980's this method has been used to locate abandoned mines and air passages and burning centers of mine fires with great success. This paper cites case studies for which this technique was successfully used.

Jan 1, 2005

By E. Niehuis, J. Y. Kim, H. G. Cramer, S. L. Chryssoulis, K. G. Stowe, C. Bendel

TOF-SIMS was used to detect, identify from parent molecular ions and determine the relative concentrations of collectors sorbed on the surface of mineral particles in concentrate and tailings samples from three Canadian concentrators. In the Kidd Creek Zn circuit, sphalerite lost to tailings carried on average a quarter of the amount of isobutyl xanthate present on that recovered to Zn concentrate; amyl xanthate, which is not reported as added to the circuit, was also detected on floated sphalerite and pyrite. At Brunswick, sphalerite particles lost to the scavenger tailings had ten times less amyl xanthate and isobutyl xanthate than those recovered to the Zn final concentrate, while both xanthates were detected on sphalerite floated to the Cu-Pb cleaner circuit. At Matagami, significantly more isopropyl xanthate and isopropyl dithiophosphate were detected on sphalerite recovered to the final Zn concentrate than on that lost to the Zn rougher tailings

Dec 1, 1995

By Arnaud Faucher, Claude Bazin, Marilène Renaud, Mohamed Mai Manga

"Grinding circuits are operated in the presence of disturbances due to ore changes and equipment malfunctions. One of the challenges faced by the operators is the detection of a disturbance, the identification of its origin and of the action needed to minimize its impact on the process. Hydrocyclones overloading, worn or partly plugged apexes of the units of a nest, surging and internal liner detachment may cause a loss of classification capacity and quality. Recovery losses in downstream leaching or flotation circuits justify the effort in developing techniques for the detection of hydrocyclone malfunction. Two approaches for the detection of hydrocyclone fault are presented in this paper. The first proposed method uses the conventional sensors available in a grinding circuit allowing real time detection of hydrocyclone abnormal operation. The second technique is based on the use of vibration sensors installed on the hydrocyclone of a nest. This last technique enables the classification of the hydrocyclone malfunction as surging, overloading and plugged apex. The two techniques can be combined to increase the robustness of the problem detection.INTRODUCTIONHydrocyclones are used for many purposes ranging from water separation, fines removal and obviously for the preparation of the feed for subsequent concentration circuits in a mineral processing plant. The strategic role of the hydrocyclones for the preparation of the feed to the concentration circuit is often underestimated because of their simplicity of operation and robustness (Napier-Munn et al., 1996; McIvor, 1988). It remains that despite their simplicity, hydrocyclones have been studied extensively from 1970 to 1990 with the objective of developing mathematical models of their operation to be incorporated into grinding circuit simulators (Napier-Munn et al., 1996; Lynch, 1977; Flintoff et al., 1987). Such a development effort is already an acknowledgement of the importance of these units in a mineral processing plant. Several authors (Del Villar et al., 1996; Plitt and Kawatra, 1979; Casali et al., 1998) proposed soft sensors to estimate the classification efficiency of hydrocyclones using sensor measurements. However, few of the proposed sensors are used in the industry. More recently several papers were published to discuss the application of 3-D modelling of the hydrocyclones (Narasimha et al., 2005; Cullivan et al., 2004) and sensors (Bond et al., 1999; Neesse et al., 2003; Hou et al., 1998; Olson and Waterman, 2004; Williams et al., 1995; Willams et al., 1997) to help in the detection of hydrocyclone malfunction."

Jan 1, 2010

By Xie Qiang

It is known that the stress state inside rock discs under Brazilian tests is neither simple compression nor tension, but a complex combination of both stress types, as well as for a beam subjected to bending, where compressive and tensile stresses are separated by the neutral axis. In this study, AE generation was obtained on pure white marbles from south Portugal that were submitted to both Brazilian and bending tests. Main questions to be answered were: (1) Does Kaiser effect exist in tests which create complex distributions of tension and compression? (2) Are there any meaningful differences in AE behavior of marble under Brazilian and bending tests?

May 1, 2009

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. The sheer volume of sensors results in mines not being able to keep the sensors calibrated. When a sensor goes off calibration, it results in errors which can severely impact plant economics. Normally, these errors are not detected until the error grows and becomes a large (“gross”) error. Undetected errors are not remedied until the next calibration, which on average are a year apart Beamex (2019) [1] across all industries. Classical statistical methods that depend on linear relationships between input and response variables are typically used to find gross errors, but are not effective for highly non-linear and non-stationary operations in mining and mineral processing industries. Calibration of sensors is time-consuming and generally requires physical intervention that results in equipment downtimes causing production losses. Therefore, in situ detection methods are warranted that do not require physical removal of sensors to compare with standard measurements or well-calibrated sensors. Data-mining based techniques and algorithms have high success rate in tackling such problems. This paper presents results from a groundbreaking multi-year big data research project whose goal was to develop data-mining-based original techniques in a multi-sensor environment to identify when sensors start to stray, rather than wait for errors to grow. The carbon stripping (gold) circuit in the Pogo Mine of Alaska was selected for this project. Maintaining strip vessel temperatures at optimum levels is crucial for maximizing gold recoveries at Pogo, and hence the focus was on the temperature sensors of the two strip vessels. An automated algorithm to detect errors in strip vessel temperature sensors was developed that exploited data from multiple sensors in the strip circuit. This algorithm was able to detect with a high success rate when bias errors of magnitude as low as ± 2% were artificially induced into strip vessel temperature data streams. The detection times of about 1 month were much less than the industry average calibration frequency of 1 year. Thus, the algorithm helps detect errors early, without stopping the circuit. The algorithm alarms can serve as triggers when calibrations are done. Experimental methodology along with results, limitations of algorithms, and future research are also presented in this paper.

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. The sheer volume of sensors results in mines not being able to keep the sensors calibrated. When a sensor goes off calibration, it results in errors which can severely impact plant economics. Normally, these errors are not detected until the error grows and becomes a large (“gross”) error. Undetected errors are not remedied until the next calibration, which on average are a year apart Beamex (2019) [1] across all industries. Classical statistical methods that depend on linear relationships between input and response variables are typically used to find gross errors, but are not effective for highly non-linear and non-stationary operations in mining and mineral processing industries. Calibration of sensors is time-consuming and generally requires physical intervention that results in equipment downtimes causing production losses. Therefore, in situ detection methods are warranted that do not require physical removal of sensors to compare with standard measurements or well-calibrated sensors. Data-mining based techniques and algorithms have high success rate in tackling such problems. This paper presents results from a groundbreaking multi-year big data research project whose goal was to develop data-mining-based original techniques in a multi-sensor environment to identify when sensors start to stray, rather than wait for errors to grow. The carbon stripping (gold) circuit in the Pogo Mine of Alaska was selected for this project. Maintaining strip vessel temperatures at optimum levels is crucial for maximizing gold recoveries at Pogo, and hence the focus was on the temperature sensors of the two strip vessels. An automated algorithm to detect errors in strip vessel temperature sensors was developed that exploited data from multiple sensors in the strip circuit. This algorithm was able to detect with a high success rate when bias errors of magnitude as low as ± 2% were artificially induced into strip vessel temperature data streams. The detection times of about 1 month were much less than the industry average calibration frequency of 1 year. Thus, the algorithm helps detect errors early, without stopping the circuit. The algorithm alarms can serve as triggers when calibrations are done. Experimental methodology along with results, limitations of algorithms, and future research are also presented in this paper.

By Horace C. Porter

Much has been written of the changes undergone by coal in storage and the deterioration of coal through exposure to the weather. In order to obtain definite information for the benefit of the Government departments and of all who store coal in large quantities, a series of tests was begun in the fall of 1909 under the supervision of J. A. Holmes, then chief technologist of the United States Geological Survey, and was continued by the Bureau of Mines after its establishment in 1910. The tests were confined to determinations of the loss in heating value of the coals and did not include a study of other deterioration; for example, in coking quality or the yield of by-products in coking. The Bureau of Yards and Docks of the Navy Department cooperated in tests of New River (W. Va.) coal, a variety largely used by the Navy. A preliminary report presenting a brief account of the early results of these tests has been published by the Bureau of Mines as Technical Paper 16.a The detailed report is presented in this bulletin, which gives a full account of the tests and the analytical data covering a period of five years' storage. Data of somewhat similar experiments for shorter periods with gas coal from the Pittsburgh bed, with Pocahontas coal on the Isthmus of Panama, and with Sheridan, Wyo., subbituminous coal, which is used for railroad and other purposes in the West, are included.

Jan 1, 1917

By Otto Sandovel Zea

El compromiso de minería perfecta se limita no solo a la preservación del medio ambiente, sino a la prevención de riesgos por desprendimiento de rocas y aplastamiento en el interior de la mina. En ese sentido, el presente texto señala la factibilidad de minar a sección plena todos los tajeos a través de la simulación de las condiciones más favorables y desfavorables de la mina, determinando como la alternativa más viable la bóveda en arco. Dicha estructura otorga estabilidad a las labores de minado -en tanto da sostenimiento activo a través del (Shotcrete SFR y Pernos Hydrabolt), así como desarrolla mayor productividad y menores niveles de riesgo por desprendimiento de rocas, menores grados de sobre excavación y genera de vibraciones al haber implementado la voladura de Pre-corte en sus labores.

Sep 12, 2011

By Karl E. Burgher

Since World War II, the need for the use of explosives with testing, construction, demolition, mining and quarrying near urban areas has increased dramatically. Once remote, testing areas have been encroached upon by commercial and residential areas. Evidence has been found that overpressure levels near these areas can be estimated using meteorological conditions. This paper reviews a study where 205 test shots were fired, meteorological conditions recorded, and over-pressure levels estimated using multiple regression techniques.

Jan 1, 1988

By Adrian Moore, Alan Richards, Andrew Brodbeck

Structural blast vibration limits should be based on the strength of the structure, the stress induced by blasting, and a responsible factor of safety. In this paper a methodology that uses direct strain measurements to determine the stress induced by blasting is described. The methodology has been used to measure strain resulting from blasting, and establish appropriate blast vibration limits on a brick sewer tunnel, an underground mine heading, brick veneer houses, a water pipeline, and transmission tower foundations. An outline is given of the use of the methodology to establish limits for the main entry heading of an underground coal mine, and transmission tower footings. The methodology that is described has reduced uncertainty factors, and permitted the specification of higher blast vibration limits than had been previously used.

By Fookes R. A, Bunch K, Gravitis V. L, Watt J. S

The combustible volatile matter in coal mine roadway dusts (CVM) has been determined using x-ray backscatter techniques. The correlation between x-ray and chemical techniques is reasonably good for the 92 samples from collieries on the Bulli seam, and the maximum error expected at the maximum level of 11· 5 weight per cent CVM permitted in the N.S.W. Coal Mines Regulation Act, 1912, as amended, is about ± 2·5 weight per cent. This x-ray technique can be used only when the combustible volatile content of the coal matter (cvm) varies within a limited range, and a separate calibration is required for each coal seam.Portable equipment based on a radioisotope x-ray source ahd digital ratemeter makes possible simple and rapid analysis, and with adaptation to use in coal mines should lead to much more comprehensive testing- ofroadways and hence improved overall prevention of coal dust explosions.

Jan 1, 1977