Search Documents

By Robert A. Siokler

Approximately 75 percentage of the earth's land surface is comprised of shale or shale-like materials. Shale itself is composed of the residue from an almost infinite variety of weathered parent materials which have undergone deformations ranging from intense to negligible. Under standard test procedures, shales exhibit a very wide range of physical properties particularly if the test specimen is subjected to a change in moisture content, when the original test values may vary from 0 to 100 percentage. It is this wide variation in physical property values compounded by its ubiquitous presence that makes shale such a problem material to engineers. In reviewing the literature relating to shale, it is evident that the "problem" has been approached from many directions. In order to understand why shales behave as they do, investigators have sought mineralogical, geological, chemical, electrical, and physical answers. Each study yields valuable academic information, but few contribute much of value to the engineer in the field. Many valid relationships between shale strength or competency and clay type, clay content, organic content, water content, grain size, cementation, density, porosity, etc, have been established. Yet it is very difficult to extend these understandings to the in situ condition with results that can be used by the field engineer. One major reason earlier work has not produced better information lies in the ambiguity of the definition of shale. It is apparent that no one laboratory parameter can be successfully used to provide sufficient engineering information to properly describe in situ conditions. For example; shale with swelling clays will produce low strength values provided: the swelling clay is in sufficient quantity, the clay is dispersed throughout the medium involved, and there is a low value of cementation. Shales with high unconfined compressive strengths have been found with very low shear strengths. Sandy shales often provide as many ground control problems as clay shales. Shales of similar nature may provide good roof conditions in one part of a mine yet in another part of the same mine the apparently identical shale may cause substantial problems. A clear need exists to classify shale in a manner which will enable the engineer to better predict the strength and durability of shale-like materials. Studies at the University of Missouri-Rolla (UMR) have focused on finding parameters which influence durability and competency, while being discretely discernible through uncomplicated testing. Initial research concentrated on distinguishing shale8 on the basis of standard physical tests such as: unconfirmed compression, triaxial shear, and slake durability. As results accumulated, however, it became evident that moisture content played a much greater role in determining competency than had been recognized previously. As a result the focus of the research turned to developing tests which would evaluate the influence of moisture on shale behavior. The above work then became a foundation for a second phase of investigation in which a suite of standardized tests were developed to provide a classification procedure. From this study five tests were identified as being critical: Moisture Activity, Atterberg Limits, Submersion, Unconfined Compression, and Shore Hardness.

Jan 1, 1986

By Noel C. Joughin

In making judgements on tolerable levels of risk in industry, and in all spheres of life, it needs to be understood that every action gives rise to risk. Without risk, nothing can be done. Without risk, no economy could be advanced. There is a strong tendency to emphasize the risk at work, but persons who are not working are exposed to a different set of risks. Often persons who are not working face greater risks than persons who are working. Simply, in being alive, one is exposed to the risk of an accident, the risk of contracting a disease, and an extremely diverse variety of other risks. According to the Health and Safety Executive of the UK, it is not possible to have a state of zero risk, because ?a state of zero risk does not exist?. Because zero risk is a physical impossibility, it is not possible to design for a state of zero risk in all engineering design. While the strategic target of achieving zero risk is laudable it does not provide any practical guidance to engineers as to what acceptable limits of risk should be. This causes a significant and real problem in the design for and the management of risk. Without meaningful guidelines, engineers, managers and the authorities often find themselves in disagreement. Thus, it has become essential to establish criteria for tolerable levels of risk and unacceptable levels of risk in order to design and manage engineering systems properly.

Jan 1, 2011

By AIME AIME

T HE appointment of Herbert Hoover to the portfolio of Commerce in the President's Cabinet is to engineers the fulfillment of a long deferred hope to have an engineer in high political office and is a matter of congratulation to us for three reasons; because he is a mining engineer who represents the highest type of idealistic engineering effort; because he is a past president of the Institute; and because he has probably a broader grasp of world problems than any other living engineer. Frank A. Vanderlip in the preface to his book "What Happened to Europe" tells of the many interviews he had with the most prominent men in Europe which were made possible for him by his eminence as a banker and by the courtesy of the American ambassadors. He cites by name such well known figures as Austin Chamberlain, Sir Auckland Geddes, Monsieur Delacroix, Monsieur Briand, Mr. Padkrewski, Mr. Venizelos, Colonel House, General Pershing, Mr. Baruch, and many others and says :

Jan 1, 1921

By C. A. Herbert

WITHIN the past few years, considerable development has been made in the coal-mining industry in Illinois and Indiana and it is the purpose of the authors to record its most important phases. Perhaps the two most striking features are the entry into the producing fields of certain large consumers of coal and the magnitude of some of the new operations. Mines are now being equipped by the. Chicago & Northwestern R. R., the Chicago,. Burlington & Quincy R. R., the Standard Oil Co., of Indiana, and the Union Electric Light & Power Co. of St. Louis. Besides, the U. S. Steel Corpn. has increased its coal-mining activities by commencing operations on its large holdings northeast of Benton, Franklin Co., Ill. Until recent years, the supply of coal has commonly been adequate and prices have generally been favorable, especially to large consumers, as the magnitude of their purchases enabled them to obtain satisfactory quotations from producers. In fact, most consumers of coal have believed that they could buy their fuel more satisfactorily in the open market than they could produce it themselves. The entry of the United States into the war was accompanied by various disarrangements of industrial conditions, and a demand for coal in excess of the supply seemed likely to be experienced for an indefinite period. Under these circumstances it seemed that the greatest assurance of a supply of fuel was its production by the operation of mines. In the case of the Chicago & Northwestern R. R. and the U. S. Steel Corpn. the production of coal has been carried on for many years with satisfactory results, but the C. B. & Q. R. R., the Union Electric Light & Power Co. and the Standard Oil Co. of Indiana had not been producers of coal, at least in this district. Apparently the most impressive feature of the newest mines is their capacity, for in some cases it is planned that production shall be in the neighborhood of 1000 tons per hr. There are mine, now in this field having nearly that output, but these were not planned for such

Jan 9, 1919

By Mick Fritz, Tom Treleaven

The success of any blast is dependent on the accuracy of the blast design and field controls placed at the shot location. The procedure by which the data is collected and analyzed is paramount to accomplishing the anticipated blast results. lf the geometry of the blast is not measured correctly, then the results will not meet expectations. Measuring the geometry and compensating for bole hole deviations is crucial not only to the lnitlal blast but also for any consecutive blasts. Excessive bore hole deviation can cancel any new technology in use. However the instruments and skills required solving this Issue are readily available.

Jan 1, 1998

By Christopher Snee

??care has to be taken that the design is driven by sound geological reasoning and rigorous engineering logic rather than by the very attractive images that appear on the computer screen.??Hoek 1999 Design of a cavern is inextricably linked to the engineering geology of the site. The importance of sound geological reasoning will be illustrated by transportation projects in New York City where there are proposals for at least 11 caverns. These caverns have been the subject of advanced exploration techniques and geological interpretation but even so the raw data falls short of the sophistication of modern numerical methods. This paper will give geological explanations for the engineering characteristics of the rock in New York City which will provide guidance for practitioners when approaching cavern design in New York and elsewhere.

Jan 1, 2008

By Douglas D. Campbell, Alan S. Imrie

INTRODUCTION Mica Dam is located on the Columbia River just downstream of the "big bend" of the Columbia, where it leaves the Rocky Mountain Trench and begins to flow southwards, approximately 85 miles north of Revelstoke, B.C. (Fig.l). The dam was built as one of three Columbia River Treaty dams in British Columbia which regulate the flow of the river and provide flood control downstream in Washington and Oregon. In addition, the three Canadian dams make possible greatly increased power generation at existing power plants in the United States and further development along the Columbia and its tributaries in British Columbia. History Mica Dam, constructed during the period 1967 to 1973, is a zoned earthfill embankment 650 feet high, which has 12,000,000 acre feet of live storage and an available head of 550 feet. Power intakes which would serve either a six-unit surface or underground plant were incorporated into the design and construction of the right abutment of the dam (Fig. 2). Prior to 1971 alternative 2500 MW capacity surface and underground powerplant arrangements were studied. Cost estimates for the two alternatives were the same within the limits of estimating procedures. However, it was believed there was a certain continuing risk in locating a surface plant at the toe of a steep canyon wall. Therefore, in 1971 a tentative decision was made to proceed with an underground plant, provided that additional exploration confirmed assumptions of

Jan 1, 1976

By G. J. Hearn

between particles in the classifying region is then

Apr 1, 1995

By Douglas Rudenko

Most engineers, mine operators, or contractors acknowledge the importance of having accurate subsurface information in order to plan a project or solve a problem. Conventional methods of exploring the subsurface such as augering, core borings, or test pits can provide information, but it is often costly and sparse. Geophysical methods offer an alternative to help supplement sparse information~ gathered through conventional exploration techniques.

Jan 1, 1998

By Herbert Hoover

DURING the year, the' Institute has made the most remarkable growth in its history. Our actual increase in membership was 1816 and therefore was 80 per cent. larger than any previous year. Even without expectation of any abnormal growth, we should pass in the year 1921 the 10;000 mark. The causes of this increased growth are not far to seek.. They lie in the widening vision of the Institute's work, not only in its relation to' the profession but as an avenue of service to the nation as a whole. The Institute is today in the first rank of influence among public institutions in the country. During this year we have, for the first time in many years, had a ?deficit of some $3000 in our finances. The sum is not important, but it- does indicate the tendency of the times, and that is the high cost of living:' The increase in our expenses lay, to the largest degree, on the publishing side of the Institute's work. If we compare the year 1918, as a fairly repre¬sentative year, with that of 1920, we find that the costs of issuing the' Institute's publications, after deducting the income received from these publications, shows a .net increase of about $33,000. for the year. This has been to some degree due to the enlarged membership but to a large degree due to the cost of the paper and printing.

Jan 1, 1921

By W. M. Middleton

The exploiting of geothermal steam is a new endeavor in this country and is for that matter a very new science in the world. With the majority of steam wells in the world having been drilled during the last twelve years relatively little experience and knowledge has been gained that can guide us as compared to the techniques the oil and gas producers have developed for their use. We few technical personnel associated with the field find it a continuous challenge to understand and explain what effects or causes the various unusual phenomenon experienced. We have had unending discussions attempting to formulate pet theories which we can use as guides. We know, so the geologists tell us, that the source of the heat is from the hot magmatic core of the earth. Theory has it that the magma is cooling off and that hot gases are given off as this magma cools and shrinks. In volcanic' areas along fault lines where the magma reaches closer to the surface than in other areas, there is a higher concentration of gas evolution; consequently, geyser or geothermal areas are developed. As these hot gases rise toward the surface they encounter various minerals, including overlying bodies of water. It is into these underground lakes that our wells are penetrating. As the heat enters these lakes it spreads out by conduction, convection and water migration. We can strike this hot water over quite large areas in many of the geothermal fields. At present there is one anomaly to this in the United States as there is in Italy where our wells do not penetrate a hot water lake. This is at The Big Geysers in California. Here superheated steam is produced with a heat content, so high that it could not have been boiled off of a fresh water pool. This puzzled us until last year when a well was completed into a large body of brine in the Imperial Valley. This brine exists at close to 500°F and at a hydrostatic pressure sufficient to preclude any boiling. It is now believed by some of us that a similar pool of brine must exist below The Big Geysers area, from which the steam is emanating. If there is such a brine pool, it offers a plausible explanation of the high-heat content, for brine boils at a higher temperature than fresh water. I am now beginning to think that a similar brine pool may exist under all the geothermal basins for if it is under two of them, it is highly probable that it is under the others. The partial understanding of what we are drilling toward, and formulating a theory to explain its behavior helps guide us in our steam well drilling.

Jan 1, 1963

By G. M. J. van Heerden, R. C. W. Webber-Youngman

"This article describes the re-engineering principles applied in the design of a personnel transportation system for the Bafokeng Rasimone Platinum Mine in the Rustenburg area of South Africa. It incorporates conveyor belt travelling, chairlift operation, and also includes consideration of proposed changes/modifications to the existing conveyor belt infrastructure.The purpose of the project was to identify, through a process of evaluation, the appropriate option and/or combination of transportation options that would be safe in terms of personnel transportation as well as cost-effective. Alternative measures for transporting personnel (not using belt riding) would have a significant positive spin-off, increasing the availability of the belt and thereby increasing production. This paper explores the feasibility of interventions that would improve safety through eliminating risk associated with personnel transportation as well as contributing towards improving the mine’s position on the cost curve.The design in consideration at the Bafokeng Rasimone Platinum Mine consists of two shaft systems, namely the North Shaft and South Shaft, each comprising twin decline shafts. One of the decline shafts is equipped with a conveyor belt for rock and personnel transportation, and the other with a winder for trackbound material transport. The conveyor belt has been used for personnel transportation since the commissioning of the shafts. The conveyor belt is equipped with platforms for personnel getting off and on the belt and a number of safety devices designed to ensure safety while travelling on the belt. Intensive training in the practical aspects of belt riding is given to every person, and unsupervised riding on the belt is permitted only once belt riding competence is demonstrated. Despite this, the safety results were poor, with 106 injuries between 2006 and May 2013. Fortunately, no fatalities were reported during this period.An investigation of alternative means for personnel transportation or engineered solutions to the current conveyor belt infrastructure in the safest, most effective, and most economical way was therefore needed. There was a major risk of safety-related stoppages being imposed following another belt accident/incident. This would prevent the mine from transporting personnel underground by belt and result in major production losses. From the commissioning of the Phase 2 shaft deepening project on both shafts, dedicated chairlifts have been used for personnel transportation as opposed to the conveyor belt installed in the Phase 1 area. The chairlifts have been in operation since 2004 and no chairlift-related incidents have been recorded thus far. According to safety statistics, it is clear that the chairlift is the safer method for the transportation of people in the shaft.To fulfil the objectives/scope of this study, it was recommended that both primary (new chairlift decline with infrastructure) and secondary options (modifications to the current conveyor belt infrastructure) be considered for implementation on both the North Shaft and South Shaft to reduce or eliminate accidents/incidents as a result of belt transportation. The associated capital expenditure would be approximately R200 million. Considering the future impact on the business as a whole, this would definitely be capital well spent."

Jan 1, 2016

By A. Bobet

Design of a new underground laboratory is underway through the auspices of the United States National Science Foundation. The Deep Underground Science and Engineering Laboratory (DUSEL) is scoped to provide a diverse group of researchers with a dedicated underground facility capable of supporting a broad spectrum of fundamental and applied research at depth in the Earth?s crust. Key research partners in the endeavor are physicists, biologists, geoscientists and engineers. Engineers are not only designing the underground facilities, but are also actively involved in developing research initiatives. This paper will introduce the DUSEL engineering research program to the mining community, provide an overview of the site, geology, and laboratory facilities, and describe some key program initiatives. The particular technical challenges and opportunities afforded by the construction of DUSEL and the performance of the integrated science-engineering program will be discussed by reference to a subset of research initiatives that are currently under development: Cavern Design, CO2 Sequestration and Transparent Earth. These research initiatives target the development of new techniques that can support improved subsurface investigation, design and construction procedures. An increased use of the subsurface can actively contribute to the development of new, more sustainable solutions for use in mining and civil engineering practice.

Jan 1, 2011

By Forrest C. Neil, Clint J. Keifer

The pollution of our water supply, Lake Michigan, is a continuing threat so long as our overflows from combined sewers exist. The problems have become even more acute during recent years, due to the increase of paved area- which accelerates and enlarges the flows of storm water. After each storm, mixtures of raw sewage and storm water spill into our waterways. If the storm is too large for the drainage systems, the mixture backs up into our streets and basements. Under severe conditions, it may even become necessary to open the locks, and discharge the polluted water into Lake Michigan. Consider the scope of the problem, as shown in Figure 1. The area in which combined sewers exist is 375 square miles, located in the central parts of Chicago and 49 suburbs. There are an estimated 640 overflow outlets to the waterways, each requiring attention. The capacity of outlets tributary to the waterways has increased dramatically over the years. Each time a pocket of upstream flooding is drained into the channels, the problem of its rapid disposition increases. Another difficulty is that the bottom of our waterways is covered with a blanket of accumulated sludge, ranging in depth up to 3-feet. This material harms the water quality by depleting the supply of oxygen dissolved in the water ... a final

Jan 1, 1997

By Stephanie Price

Engineering Associations ?Regulatory authority ?License individuals and firms ?Discipline licensed members ?Enforce against improper acts ?Programs for EIT?s, competence, etc

Oct 1, 2010

By P. J. Knottenbelt

Outcomes from a workshop organized through the SAIMM revealed that the minerals and metals industry must develop its ?Engineering Team? if it is to continue to meet the challenges of globalization. The very economy of the country is largely dependent on a competitive and stable engineering team within the minerals and metals sector. With the Chamber of Mines (COM) passing on its education and training initiatives to the industry, the professional bodies like SAIMM must (despite meagre resources) continue the good work done through the COM in the past. The workshop highlighted recruitment and selection, further/higher education, socialization and initial training, deployment and retention and continuing education as priority areas. These are further detailed in this report. Office Bearers have considered the outcomes and the areas where the Institute should or should not be involved have been stated.

Jan 1, 2002

By J. L. Perry

FOR many years, you and your fellow members of the American Institute of Mining and Metallurgical Engineers have devotedly and ably applied yourselves to the art of making iron and steel. having foremost in your minds the conservation of raw materials, suitable and efficient facilities, economical processes, and improved quality of product. For the past three strenuous years you have contributed wholeheartedly to meeting the problems of increased production. You have conducted scientific and technical investigations and research, recommended experiments. and gathered all the available and valuable information possible to gain the desired objectives. You have had many obstacles and difficulties to overcome. In the early days of your organization, there was some lack of co-operation from the industry itself-perhaps, for example, some failure to recognize the mutual advantages of free exchange of experiences and information. But regardless of any hindrances, you have made many and valuable contribution which have tended to make iron and steel manufacture leas of an art and more of a science.

Jan 1, 1944

By Joseph L. Margin

From a stubborn start to record setting performances in little over a year, that is the story of the English Running Tunnel Boring Machines. The program to transfer technical information on these highly advanced machines from builder to user will be discussed as a vital link to this accomplishment. Some interesting features of these machines will be covered as well as a recounting of the various conditions that were encountered during these drives and how they were resolved.

Jan 1, 1991

Rio Tinto has embarked on a journey to use automation to improve the performance of its surface mines. The driver for automation is to improve the accuracy and consistency of mining processes and less to do with cost savings through labour reduction. A key task in most surface mines is blasthole drilling. The degree to how well this is done cascades through the downstream mining process. It impacts scheduling, excavation, slope stability, material handling, beneficiation and final product blending. Improved blasthole drilling was identified as an objective that has a significant business case in most of Rio Tinto's surface mines. This paper describes Rio Tinto's drill enhancement project that has developed a robust system for automating most of the functions on a Terex SKSS16 drill rig. Automated drilling is currently being used in production at the West Angelas iron ore mine in the Pilbara region of Western Australia. A description of the essential elements of the drill automation system is given together with an overview of how automated drilling is performed remotely from the mine office. A review of some of the benefits of the enhanced drill system is given together with the future plans to extend the functionality of the automated drill and the expected benefits.

May 1, 2010

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012