Search Documents

Filtration systems with disposable filter elements (DFEs) are used in the underground coal mining industry to control particulate matter emissions from diesel-powered permissible and nonpermissible coal mining equipment. This study was conducted in underground mine conditions to evaluate three types of high-temperature DFEs used in those filtration systems. The DFEs were evaluated for their effects on the concentrations and size distributions of diesel aerosols and concentrations of nitric oxide (NO) and nitrogen dioxide (NO2). Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. After an initial DFE degreening period, the filtration system with all three DFEs was found to be very effective at reducing total mass concentrations of aerosols in the mine air. The effectiveness of DFEs in filtering aerosol mass was found to be a function of the engine operating conditions. The efficiency of the new DFEs significantly increased with accumulation of operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on performance of the DFE elements. The effectiveness of DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for both DPFs and DFEs when the engine was operated at high-load modes than at low-load modes. Initial heating of certain DFEs resulted in visible white smoke and substantially elevated aerosol number concentrations. The effects of the DFEs on total nitrogen oxides (NOX) concentrations were found to be minor. The NO2 fraction was found to be generally lower for the DFEs than for the muffler. The engine-out NO2 fraction of the total NOX was found to be substantially higher for low-load modes than for high-load modes.

Jan 1, 2011

By David Hopkins, Steve Klein, Bradford Townsend, Ed Sum, Derek Penrice

INTRODUCTION The Transbay-Caltrain Downtown Extension (DTX) Project involves the construction of an approximately 1.5-mile rail line that will extend Caltrain commuter service and the future California High Speed Rail system into downtown San Francisco. The underground rail extension will be constructed by mined tunnel and cut-and-cover methods. Tunneling challenges include difficult ground conditions, low rock cover, the presence of historic buildings along the alignment, and the large tunnel span, ranging from approximately 50 to 65 feet. Three mined tunnel construction methods were evaluated: the Stacked Drift Method, the New Austrian Tunneling Method/Sequential Excavation Method (NATM/SEM), and Tunnel Boring Machines (TBM). This paper describes the challenges presented within the mined tunnel section, and summarizes the evaluation of tunneling methods that led to the selection of NATM/SEM. PROJECT OVERVIEW The existing Transbay Terminal opened in downtown San Francisco in 1939. This facility is antiquated, and does not meet current building seismic safety standards or the transportation needs of the Bay Area. For these reasons, San Francisco voters approved Proposition H in 1999, which proposed to construct a new or rebuilt regional transit center at the site of the existing terminal and extend Caltrain commuter rail ser-vice to the new transit center. The new transit center is the hub of the Transbay Transit Center (TTC) Program, which will greatly enhance regional transit service by providing connectivity for six Bay Area transit providers at one facility. The program will be the largest inter-modal centerwest of New York City. The TTC Program is comprised of two major projects, the Transit

Jan 1, 2007

By R. W. Fedors, S. T. Green, G. R. Adams, C. Manepally, L. B. Browning

This paper provides estimates of large-scale temperature gradients that can be used to support modeling of natural convection and cold-trap processes in thermally perturbed drifts. Temperature influences estimates of the quantity and chemistry of water contacting engineered components (e.g., drip shields and waste packages) in a potential high-level waste repository at Yucca Mountain, Nevada. Temperature gradients drive natural convection and cold-trap processes, which could affect the distribution, quantity, and chemistry of liquid-phase water contacting drip shields (waste packages).The confluence of high temperatures, liquid-phase water, and high chloride may lead to corrosion of drip shields and waste packages. An overview of the evolution of environmental conditions in thermally perturbed drifts is presented to provide a context for the estimates of temperature gradients. A mountain-scale conduction-only model is used to estimate temperature gradients and temperature differences for a drift located at the center of a potential repository. Thermohydrologic models and heat transfer algorithms are used to evaluate the reasonableness of the conduction-only results. Estimates of temperature using an in-drift heat transfer algorithm account for the possibility of drift degradation and formation of a rubble pile on the drip shield. Temperature differences between the center and ends of the drift are estimated to rapidly increase to 80 °C soon after repository closure. That temperature difference decreases over time to 15 °C after 10,000 years. Local temperature gradients are generally estimated to be less than 0.2°C/m, though the gradients can be much larger near changes in lithology and near the end of the drift. The estimates of temperature gradients do not account for intermediate- and small-scale variations, such as those influenced by differences in heat loads between waste packages, intra-layer variations in thermal properties of the surrounding fractured rock, or localized drift degradation.

Jan 1, 2004

By Marline J. Veesaert

Urban quarries offer one of the greatest opportunities for profit in non-metallic mining with limited financial risk IF properly evaluated, planned and developed to meet market needs. Location, with respect to market, is the prime consideration. Geologic considerations and quality of rock are nearly as important. Cost factors and return on investment (ROI) are the principal financial considerations. Risk of capital is determined by weighing all factors that should be considered and how well judgements are based on information acquired. It is a simple, true axiom of business that an investment must be founded on amount of capital required with its expected return plus profit, expertise required to operate and time involved. Urban quarries generally offer excellent stone product market opportunities. Costs of land with mineral containment and processing operations are much greater than in rural areas. Environmental problems have become increasingly severe. Competition from other quarries in the market area is usually directly proportional to the profit attractiveness. Risk of capital (initial, developmental and operational) can be evaluated and reduced only by thorough analysis of the entire situation. Time and money expended on planning and preliminary investigations probably represent the most productive investment of available company resources.

Jan 1, 1977

By J. F. Archibald

A research effort has been undertaken, under Workplace Safety and Insurance Board of Ontario (WSIB) sponsorship, to characterize the support capabilities of conventional and innovative spray-on lining materials for mitigating dynamic failure effects created by simulated rockbursts. Conventional spray support media, such as shotcrete and fibrecrete linings, and a variety of new spray-on lining materials [thin, spray-on liners (TSLs)], typically polymer-type thin coatings, were subjected to simulated rockburst influence. For baseline comparison, conventional rockbolt and bolt-and-mesh support products were also evaluated. Observation of lining performance was undertaken through completion of field-scale support and rock detonation trials. Controlled blasting tests were conducted at the Queen’s University Explosives Laboratory to examine the effectiveness of the variety of surface coating agents for modifying dynamic rock spalling processes. All tests were performed upon largely undisturbed and homogeneous rock materials in highly repeatable fashion. All blasts were observed seismically and photographically to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion and support liner survivability characteristics. These material comparison trials were performed to assess the relative effectiveness of a wide range of currently available area support techniques for suppressing hazards associated with dynamic rock ejection. The results of this study validate that thin, spray-on linings may be equally as effective, and often better, than conventional support materials at mitigating rockburst or like damage in highly stressed mine environments.

Jan 1, 2004

By F. Schreiter

The Ore Mountains in Germany have a history of more than 850 years of underground mining activity. This has created a situation where thousands of old mine shafts and adits are due for rehabilitation. While no long-term stable rehabilitation was executed in previous centuries, those abandoned mine sites which date back to the uranium mining boom from 1945 to 1962 were rehabilitated immediately after mine closure according to state-of-the art technology. Over the years, however, it has become obvious that most of these sites are not long-term stable and thus it has become necessary to rehabilitate them a second time. Technical University Bergakademie Freiberg is carrying out a research project on the optimization of this process. 70 mine site rehabilitation projects, the technology and the materials used have been assessed. A technical guideline for future rehabilitation projects, based on the outcomes of this assessment, is under development with the goal to make it easier, faster and more economical to select and apply suitable designs and construction materials for dams, plugs and other rehabilitation structures in former uranium mines.

Feb 27, 2013

By Robert H. Robinson, Levent Ozdemir, Russell J. Miller

The paper summarizes an investigation into the applicability of mechanical excavation to oil shale mining; identifies available machine types that are best suited to various aspects of the mining operation; presents preliminary comments on the configuration of an "IDEAL" oil shale mining machine; and establishes the background information necessary for conceptualizing and evaluating new mining methods using mechanical excavation equipment. Conclusions are also presented as to the best currently available systems, as well as potential future systems.

Jan 1, 1983

By Nikhil Dhawan, Ashwini Kumar, Yogendra Pratap, Himanshu Tanvar

India does not possess any soluble potash reserves and depends completely on imports. In this study, an attempt has been made to recover potash (K) values from the mica sample employing thermal and mechanical routes followed by leaching. Direct leaching of mica in different lixiviants is found to be ineffective with very low K-dissolution (1–5%). Heat treatment with different fluxes, such as NaCl, NaOH, and CaCl2, is carried out and almost 85% K-values are recovered. Mechanical activation of mica and with different calcium additives is carried out to recover potash values. K is recovered in leach solution in the form of soluble salts, such as K2CO3, K2SO4, and KOH, and leach residue consists mainly of calcium-alumino-silicates. Using mechanical activation with flux, it is possible to recover >95% K-values from mica sample. Mechanical activation with calcium-based flux is found sustainable in the recovery of K-values from mica.

By Thomas Novak, Robert Goldstein

The analysis of a machine-luminaire configuration is a time- consuming process requiring the construction of a machine mockup, installation of a designated lighting arrangement, and an extensive set of illumination measurements. This entire process, however, is well suited to computer analysis. By simulating the machine geometry and the characteristics of the desired luminaires, the incident light levels can be calculated at the required set of points. This Bureau of Mines paper presents a general description of the techniques involved in performing this simulation.

By Michael J. Sapko, William D. Monaghan, Michael A. Trevits

Mine seals are used extensively in underground coal mines to segregate mined-out areas and to isolate fire zones or underground areas that are susceptible to spontaneous combustion. Over the years, 30,000 mine seals have been erected in underground coal mines in the United States. Mine seals, along with rock dusting and ventilation, represent the fundamental means of preventing underground coal mine explosions. In this study the National Institute for Occupational Safety and Health (NIOSH) used ground penetrating radar (GPR) technology to determine if each of three test mine seals were uniformly constructed. Three mine seals representing different construction methods and materials (cast-in-place foamed cement; solid block, polyurethane foam and gravel; and wire mesh, rebar and gunite) were erected at the NIOSH Lake Lynn Laboratory’s underground mine as part of an on-going research program. The seals were imaged using GPR with 400-, 500-, 900-, and 1,000-MHz antennas. We found that variations in uniformity existed in the material for the cast-in-place foamed cement seal. Variations in uniformity also existed in the seal made from solid block, polyurethane foam and gravel. The post-processed radar records correlated closely with recovered core samples (areas of gravel and polyurethane foam, and areas containing only polyurethane foam). Finally, the radar records of the seal made of wire mesh, rebar and gunite showed the various components. The results of this work suggest that GPR could be used as a tool to evaluate mine seal characteristics and construction uniformity.

By V Kveldsvik, N Ragvin, T Eiken, G Grøneng, G V. Ganerød

Catastrophic rock slope failures have caused destructive tsunamis in Norwegian fjords. At the Åknes rock slope the tsunami generating potential is large due to the potential large volume involved in a possible catastrophic failure. Widening of the upper crack has been recorded since 1986, and in recent years, a quite extensive investigation and monitorin campaign has been conducted. Data from some of these investigations are presented and analysed with respect to a preliminary evaluation of the stability of the slope.

Jan 1, 2006

By M. Steyn

[Zr(C9H6NO)4]?(HCON(CH3)2)?(H2O), where (C9H6NO) = 8-hydroxy quinoline (oxH), was synthesized and characterized. This tetrakis-coordinated zirconium complex crystallized in the triclinic crystal system (Pi, Z=2) along with water and N,N?-dimethylformamide(DMF) solvate in the asymmetric unit. The metal atom is surrounded by four N,O-donating bidentate ox-ligands that are arranged around the metal centre to give a square antiprismatic coordination polyhedron with a small distortion towards a dodecahedral geometry. Crystal packing is stabilized by intermolecular interactions of adjacent oxine ring systems in neighbouring molecules, as well as hydrogen bonding of the aqua and DMF solvate molecules, linking the molecular entities into a supramolecular three-dimensional network.

Jan 1, 2013

By P. Zhang

The use of phosphate depressants in the cationic flotation of silica from francolite in the Florida phosphate industry is rarely practiced. The occasional use of gelatinized starch derivatives and pH adjustments to assure a slightly alkaline flotation feed slurry pH have been used in some processing plants to improve selectivity. This paper presents a preliminary laboratory comparison of several potential phosphate depressants for use with the flotation of siliceous phosphates. It was found that starch is ideal for floating fine (-35 mesh) silica from phosphate, while sodium tripolyphosphate may be the best for coarser (+35 mesh) feeds.

Jan 1, 2009

By D. J. Pyra, J. Kudelko, Korzekwam W.

Polkowice region (Lower Silesia, Poland) is an area, where the copper mining activity started about 40 years ago and new technologies were applied. There are 3 underground mines, 3 processing plants, tailings pond (the biggest one in Europe), pipelines for flotation waste transport, railways. Although new technologies were applied during the copper ore exploitation, the environment in this area were polluted mostly by dust containing copper, lead, zinc and arsenic. Estimated values of heavy metals in polluted soils were compared to the natural contents of this metals. The geochemical background for Polkowice area was defined. The pollution zones occur around mining facilities. Copper ore exploitation and processing is planned for the next 20-40 years depending on market situation. After mines and other facilities closing the most important problem will be sustainable development of this area. To evaluate the scope of revitalization activities the analysis of recent soil environment condition will be necessary as well as forecasts for pollution migration. Geostatistic methods used also in mining will be very helpful for this task.

Jan 1, 2005

By L. Yuan, J. H. Rowland, D. Bahrami, R. Thomas

Blasting is the main method of production in many non-coal underground mining operations and produces multiple toxic gases as a result. The Mine Safety and Health Administration (MSHA) requires mine operators to measure the level of toxic gases in mines as frequently as necessary to ensure they are below regulatory safety limits. The current practice uses portable gas monitors to check the concentrations of toxic gases after a fixed post-blast time. This paper studies the application of a gas monitoring system in the return entry of a limestone mine to determine a safe re-entry time. The National Institute for Occupational Safety and Health (NIOSH) conducted such a monitoring program in a limestone mine from September 2016 through May 2018. NIOSH/PMRD (Pittsburgh Mining Research Division) is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions. This study showed that the use of gas monitoring in the return air can be a useful tool at the mine operator’s disposal to detect and reduce the risk of hazardous conditions and also to reliably estimate the re-entry time.

By Baxter J. L

Post-tertiary training programmes have been designed and produced for geologists at different levels of understanding and expertise in the relationship between gold mineralization and shear zones. A workshop format was used as it allowed both clients and facilitators to participate in the learning process. Evaluation by facilitators and participants refined the workshop programme as an effective skills oriented learning process. The general observation is that post-tertiary training in small, interactive, practical, learning oriented groups is far better than lecture oriented short courses for developing skills based learning. The evaluation indicates that the process in post-tertiary training must include aspects which are both useful and used.

Jan 1, 1989

By D Reddy

Rosh Pinah Zinc Corporation is a zinc-lead mine located in southern of Namibia. It is currently considering the development of a low grade ore body containing about 2.8% zinc. This ore can be utilised by the concentrator if it could be upgraded prior to the ball mill. Preliminary work indicated that the ore may be upgraded in a pre-beneficiating stage by using dense medium separation, X-ray sorting or a combination thereof to a feed grade of minimum 9% zinc. This paper describes the process followed in evaluating the technologies for pre-beneficiation. The results from test work indicated that the low grade ore is amenable to pre-beneficiation by both dense medium separation and X-ray sorting. A comparison between the two technologies showed that dense medium separation marginally outperformed X-ray sorting on grade and recovery. The results for the X-ray sorting were achieved by tuning the calibration curve specifically for the samples tested.

Jan 1, 2008

By V. Krupa, E. Lazarova

A method is proposed for the continuous calulation of a rock mass in real time while tunnelling with a TBM. Rock properties are investigated through models of the fracture stress under the disc cutters, the quasi-shear stress between the disc cutters and the specific energy of cutting under the disc cutters. Comparison of theoretical and monitored data of cutting specific energy can be used to determine theoretically the prevailing shape and size of the bulk debris. The shape and size of the chips from a given rock vary with the boring parameters. Introducing shape and volume corrections into the models of the evaluated stresses suppresses the influence of the boring regime and allows the rock properties to become dominant

Dec 1, 1996

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By T Higuchi, L Lu

The quality of iron ore fines have been deteriorating, which has affected sinter quality and productivity adversely. New pretreatment and sintering technologies are therefore required to tackle the gradual change in the quality of iron ore fines. In the sintering process, iron ore fines are first granulated with fluxes such as limestone and coke breeze, and are then loaded and fired in a sinter machine. Sinter productivity and quality are heavily influenced by the reactions occurring in the sintering bed. Hence fundamental understanding of these high temperature properties of ores is urgently needed.Formation of initial sinter melt, penetration and assimilation of nucleus particles by the initial melt, and consolidation and final solidification of final sinter melt are believed to be the key sintering reactions. The assimilation and penetration phenomena have been studied separately in the literature with model particles and diffusion couples and are therefore difficult to relate to sinter quality. In addition, the effect of ore mineralogy has not been studied in detail.In this study, tablets consisting of coarse particles from various iron ore fines as nucleus particles and chemical reagents as adhering fines were made and fired under various sintering conditions to investigate the penetration and assimilation behaviour simultaneously. The degree of assimilation, pore structure, compressive strength of the resultant analogue sinters were evaluated and the relationship between sinter strength and ore characteristics was further discussed. The nucleus particles from Ores A and B were found to be more porous and assimilated more readily with sinter melt, resulting in a viscous melt and a macro-porous sinter structure. The nucleus particles from Ores C and D on the other hand, assimilated less readily with sinter melt, resulting in a fluid melt and a denser sinter structure. This is consistent with the results reported in the literature, suggesting that the present evaluation method can be utilised for studying sintering reactions and predicting sinter quality.CITATION:Higuchi, T and Lu, L, 2017. Evaluation of sintering behaviour based on ore characteristics, in Proceedings Iron Ore 2017, pp 303–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017