Search Documents

By J. E. Allison

As part of a Bureau of Mines research program to conserve critical and strategic metals, an aqueous electrodeposition method for preparing stainless-steel-type coatings was studied. Chromium powder (averaging 3 J1.m diam) was suspended in a ferrous-nickelous sulfate electroplating bath and occluded in the electrodeposited Fe-Ni alloy matrix. Subsequent heat treatment of the resulting composite coating formed the ternary alloy. The occlusion process was affected by the quantity of Cr powder suspended in the electrolyte and by the microstructure and composition of the electrodeposited matrix. Coatings containing up to 21 wt pct Cr were deposited from an electrolyte containing 20 vol pct suspended Cr powder. Heat treatment at 1,100° C for 8 h homogenized the composite coating. Deposition of 44Fe36Ni20Cr alloy coatings (250 J1.m thick) on AISI 1020 carbon steel rods, followed by heat treatment, provided complete protection of the carbon steel during exposure to a boiling 65-pct-HN03 solution. Corrosion rates of 0.6±OA mm/yr for the coating in the boiling HN03 approximate that of 304 stainless steel. Practically shaped electroforms have been prepared by the coating method.

Jan 1, 1989

By C. A. Rhoades

The spillage that accumulates under conveyor belt lines presents a possible fire and explosion hazard fomiinqjetsoruiel, especially to those who must clean up the spillage. The U.S. Bureau of Mines conducted research to reduce this hazard by identifying and investigating the parameters affecting the efficiency of conveyor belt cleaning. The amount of material carried back under the conveyor and the wear rates of metal cleaning blades decreased with increasing blade-to-belt pressure to a limiting value, after which the carryback and wear rates remained essentially constant. The optimum blade-to-belt pressure was found to be 11 to 14 psi for the research conveyor system. Greater pressures increased the blade-belt friction without improving either cleaning or blade life. The modes of blade wear were three-body abrasion and slurry erosion caused by the sand-lime test mixture. Wear rates were reduced by increasing the metal hardness, opti-mizing the pressure, and removing conveyor belt imperfections. Corrosion was not observed to affect the wear of various steels in tests of less than 34 h. The results of this study should allow mine operators to run their conveyors under conditions that will maximize cleaning and minimize equipment wear.

Jan 1, 1989

By Jeffrey S. Walker

The purpose of this U.S. Bureau of Mines effort was to determine if ground movement caused by mining-induced subsidence is directly transferred to a structure and, if so, how that transfer takes place. Four concrete block walls with foundations were constructed and monitored over an active longwall panel. Three of the walls were located perpendicular to the direction of mining in zones where maximum inclination, maximum tension, and maximum curvature were predicted to occur. The fourth wall was constructed along the centerline of the panel, parallel to the direction of mining. All of the walls and the surrounding ground surface were instrumented with conventional survey monitoring points and extensometer stations to observe the vertical and horizontal movements. The fourth wall instrumentation also included continuously recording tiltmeters. The results of this investigation indicate that these simple structures respond to subsidence in a similar manner as the ground surface. This suggests that once the transfer mechanism is more fully defined, prediction models can be developed to accurately estimate the effect of mining on surface structures.

Jan 1, 1989

By K. Y. Haramy

Coal mine bumps involve the violent, rapid failure of coal and rock around a mine excavation. Deep coal mines with strong roof and floor rocks and high-stress conditions frequently experience face and rib bumps. The bump problem is becoming more severe as mining depth increases, prompting efforts to control high stress in advance of mining. This Bureau of Mines report presents a review of the most widely used methods to detect and destress high-stress zones along coal faces and an investigation of stress-related bump problems and destressing techniques at a cooperating mine. Geotechnical instrumentation and microseismic methods were used to better understand bump occurrences in underground coal mines. Laboratory tests of the drilling-yield method for high-stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress at various confining pressures. A three-dimensional, multiple-seam computer modeling program, MULSIM, was used to evaluate the effectiveness of stress-relief methods. Modeling results indicate that dangerously high-stress areas can be controlled by either proper planning or destressing. Proper mine planning guidelines and destressing methods such as volley firing, hydraulic fracturing, and auger drilling are discussed.

Jan 1, 1988

The U.S. Bureau of Mines conducted a laboratory study to determine what effect use of water-jet-assisted cutting has on frictional-ignition suppression. A single bit with a steel tip, installed on a rotating drum, repeatedly made 22-in-long cuts in a block of Berea sandstone. The drum was operated in an enclosure that contained an explosive methane-air mixture. High-pressure front-mounted water jets operating at 2,000 to 5,000 psig and low-pressure rear-mounted sprays operating at 80 psig were used; the number of ignitions that occurred with each type of spray was compared. The rear-mounted spray was more effective for preventing frictional ignitions than the front-mounted water jet.

Jan 1, 1989

By J. L. Thompson

The U.S. Bureau of Mines conducted a water-jet-studies program using a single-bit, in-seam test unit to determine effects of a moderately high-pressure (up to 10,000 psi) water-jet-assisted cutting system on rock weakening. The in-seam test unit was used to obtain cutting force data in tangential, normal, and side force directions. Conical continuous miner and radial longwall miner bits were used to penetrate test samples of coalcrete, Berea sandstone, and Indiana limestone with unconfined compressive strengths of 4,600, 8,000 and 10,000 psi, respectively. Depth of cut in the coalcrete tests was 1 in, with 2-in cut spacing (2:1 ratio). Because of cutting equipment and instrumentation limitations, the Berea sandstone and Indiana lime-stone were cut using a 0.5-in depth of cut and 2-in spacing (4;1 ratio). Bit velocity was maintained at 25 ft/min for both bits. Each specimen and bit type was tested using 0.3-, 0.6-, 0.8-, and 1.0-mm-diam nozzles and water-jet pressures of 2,500, 5,000, 7,500, and 10,000 psig. Water-jet-assisted cutting decreased average resultant conical and radiallongwall bit cutting forces 6.4 and 8.4 pct in coalcrete, 5.5 and 1.4 pct in Berea sandstone, and 2.0 and 5.5 pct in Indiana limestone. Slight reductions of power requirements resulting from water-jet assist were ascertained during these experiments.

Jan 1, 1989

By Eric R. Bauer

The U.S. Bureau of Mines, in cooperation with a southwestern Pennsylvania coal mining company, BethEnergy Inc., Mine No. 60, Eighty-Four, PA, recently assessed the feasibility of using pre driven recovery rooms (open entry recovery) when longwall mining to increase the productivity of the coal extraction process. Two recovery entries, one 200 ft long and another 600 ft long, were supplementally supported with bolts, channels, and wire mesh, and either fly ash-cement piers or fiber cribs, then mined into by the longwall face. The recovery entries showed little deterioration as the supports provided adequate resistance to the front abutment loading. Compared with conventional recovery methods, the fullface recovery room allowed for panel extraction to be completed nearly 17 days faster and to reduce face equipment move time by 1-1/2 days. The potential productivity increase accompanying recovery rooms is greater than the cost of supporting a fullface recovery room. The fullface recovery room provided over 18 additional production days and the opportunity to mine nearly 68,400 st of coal per year per panel mined.

Jan 1, 1989

By D. E. Larson

The U.S. Bureau of Mines investigated Fe-base alloys containing 8 pet Crwith Ni, AI, and Si additions as substitutes for standard AISI Type 304 stainless steel (SS) in high-temperature oxidizing applications. The objective of this study was to reduce the amount of Cr required to make an austenitic stainless steel while retaining satisfactory workability, mechanical properties, and oxidation resistance. Alloys prepared in this investigation had a composition of Fe-8Cr-lMn-0.07C with varying amounts of Ni, AI, and Si. A minimum of 10 pet Ni was required to achieve an austenitic composition. The microstructures of the austenitic alloys were very susceptible to room-temperature, deformation-induced martensitic transformations. When the alloys were cold worked or stressed, the materials had far greater tensile strengths than Type 304 SS at room temperature. At higher temperatures, tensile strengths and workability of several of the alloys were comparable to that of Type 304 SS. Although martensitic transformation caused the room-temperature properties of the experimental alloys to be quite different than those of Type 304 SS, the superior oxidation resistance and similar hot workability of several alloys encourage their use as replacements for Type 304 SS.

Jan 1, 1989

By W. K. Connor, O&apos

The U.S. Bureau of Mines investigated the Sheep Creek prospect in the north-central Alaska Range to evaluate the Pb, Zn, Ag, and Sn resources. The studies included field investigations, mineralogical characterization, and concentration tests. Mineralization at Sheep Creek consists of disseminated, banded, and massive pyrite, sphalerite, and galena. Tin occurs as grains of cassiterite (Sn02) in the quartz-mica matrix and within pyrite and sphalerite grains, and Ag occurs in solid solution within the galena. Three bulk surface samples and two sets of core samples were collected at the Sheep Creek prospect for this study. Gravity concentration yielded products with up to 30 pct Sn, and the best result was a product that recovered 52 pct of the Sn at a grade of 22 pct Sn. Bulk sulfide flotation yielded products that recovered up to 89 pct of the Zn, 73 pct of the Pb, and 75 pct of the Ag, but grades were relatively low; selective flotation would significantly increase the grades.

Jan 1, 1989

By Jon C. Volkwein

The U.S. Bureau of Mines conducted a study to assess the impact of a directional water spray system on a unique single inlet dust scrubber on a low-profile mining machine. Tests were conducted in a full-scale model mine using a continuous mining machine. Tracer gas was introduced at the face and concentrations of the tracer gas were monitored at the face and in the return. Various parameters tested included mining position, depth of cut, brattice setback, and combinations of scrubber, and directional or symmetrical sprays. Results indicated that either water spray configuration improved the ventilation effectiveness of the scrubber by a factor of 2 to 3. Average face ventilation effectiveness (FVE) values for all testing of the scrubber and directional sprays were 0.95, versus 0.37 for a standard 20-ft blowing curtain without sprays. No FVE values were less than the standard 20-ft blowing results.

Jan 1, 1989

By Eugene H. Skinner

The U.S. Bureau of Mines conducted experiments on the use of lightweight concrete in the density range of 100 Ib/ft3 for liners in underground mines. Three test sections were completed: a monolithic, portal-type structure with integral walls and arch constructed aboveground; an underground test section constructed in a mine drift using plywood forms; and a second section constructed in a drift using an air-supported formwork. The lightweight concrete in the two underground test sections was placed using piston pumps and a slickline. Fiber reinforcement was added to the concrete in the mine sections without any apparent problems with either pumping or placement of the concrete. In another experiment, the Bureau and Hecla Mining Co., Mullan, rD, used lightweight concrete in the density range of 25 Iblfe to replace timber blocking in a raise preparation structure. Other experiments are described in which low-density, lightweight concrete blocks were produced for mine ventilation doors, stoppings, and barricades. Other mine uses reviewed include pillars and collapsing beams. An advantage of low-density concrete is that it will display up to 50% deformation at a constant yield stress. These hlllovative concepts in deformable concrete lining systems will aid mine operators by decreasing capital and maintenance costs, increasing the available space in underground haulageways, and providing productivity gains and improved resource recovery in the soft, caving, squeezing, or bursting grollnu conditions often found in deep mines.

Jan 1, 1989

By Thomas E. Marshall, Roy H. Grau

The U.S. Bureau of Mines has developed an acoustic test for determining if a rock salt sample is from a "normal" nongassy salt face or from a gassy face where an outburst has the potential to occur. The test is based on the observation that a salt sample taken near an outburst-prone zone produces an audible popping sound when it is dissolved in water. The sound is produced when pressurized gas that is trapped in salt samples is released. In the acoustic test, the sound is electronically measured, digitized, and transmitted to a microcomputer; the output is an average decibel value that classifies the sample as "normal" or "outburst." The acoustic test procedure and equipment are described, and raw test results and data analysis are shown. Results are also shown for several salt samples that were analyzed using a laser Raman microprobe.

Jan 1, 1990

By W. R. McDonald

Part of the U.S. Bureau of Mines mission is to supply the U.S. mineral industries with information that is useful in planning to meet the Nation's critical and strategic mineral needs if a national emergency occurs. The Bureau conducted laboratory research including operating a nominal 100 lblh pilot plant to demonstrate the recovery and concentration of chromite by gravity and flotation operations from three northern California mineral deposits. Gravity beneficiation test results show that concentrates contained as much as 52 pet chromic oxide (CrZ03) with recoveries of about 80 pet. Results from the bench-scale unit operations of mineral liberation, tabling, vanning, spiraling, pinch sluice, work index, and thickener area determination tests are presented in this report.

Jan 1, 1990

The U.S. Bureau of Mines conducted a series of laboratory tests in a full-scale model to determine the respirable quartz dust capture efficiency of an irrigated-filter collection system while testing different filter densities, different filter materials, preconditioning water sprays, and wetting additives in the spray water. Impactor samplers were operated upstream and downstream of the filter unit to determine overall dust collection efficiency. The impactor filters containing the 0.7-to 4.7-J.l-m size fractions were analyzed for quartz content, and these data were used to calculate quartz dust collection efficiency. The results of this testing indicated that (1) increased ftIter density improved quartz dust collection, but also resulted in a significant increase in pressure drop across the filter, (2) an alternate synthetic filter material improved dust collection without increasing pressure drop, (3) preconditioning sprays mounted in the system ductwork can have a beneficial effect on dust collection, and (4) additives to the spray water did not significantly increase dust collection.

Jan 1, 1990

By Agnes Y. Lee

As part of the U.S. Bureau of Mines program to improve base metal leach systems, pressure leaching of galena (PbS) concentrates in fluosilicic acid (H2SiF6) solution was investigated. Lead extraction was 93 pct when PbS was pressure leached in H2SiF6 at 95° C with 2OO-psig O2 pressure for 40 min, using ferric nitrate [Fe(N03)3] as a catalyst. The effects of several catalysts, O2 pressure, time, and acid concentration on leaching were determined. The purified leach solution was electrowon to recover high-purity Pb metal. The H2SiF6 used in leaching and electrowinning can be recycled continuously. A flow diagram was proposed based on this investigation. Elemental sulfur (SO) was recovered from the leach residue by solvent extraction. A method was also developed for treating the flnal residue to segregate the important byproduct elements such as Ag, Cu, and Zn and enable their recovery by standard commercial processes.

Jan 1, 1990

By J. J. Lukasko

The U.S. Bureau of Mines developed an alternative electrochemical process for the production of calcium metal. The current industrial practice is costly, complex, and inefficient. The Bureau method involved electrowinning of a calcium-tin alloy followed by electrorefining to produce calcium metal. In the electrowinning cell, CaCI2 was fed to a KCI2-CaCI2 electrolyte. The calcium was electrowon at 6500 C into the pure molten tin cathode until the cathode contained 7.5 wt pct Ca. Current efficiency for electrowinning averaged over 90 pct. The resulting calcium-tin alloy served as the anode for the electrorefming cell, which employed a [CaC~-CaF2] fused salt as the electrolyte. Calcium metal was electrorefmed at 8500 C with a current efficiency of 85 pct based on calcium metal recovered. The calcium metal analyzed 99.2 pct, which is purer than commercially produced calcium.

Jan 1, 1990

By M. Dattilo

The U.S. Bureau of Mines has been conducting research on the use of waste-derived zinc as a partial replacement for pure zinc in the electrogalvanizing process. The end product of this process is automotive sheet, which has enhanced cosmetic protection over previously used cold-rolled (CR) steel. In this study, primer-coated specimens of CR and electrogalvanized (EG) steel were subjected to the on-vehicle environment and monitored periodically by electrochemical impedance spectroscopy (EIS) during immersion in 1M NaCI solution. The results of these tests were compared with immersion-only conditions. Scanning electron microscope (SEM) and energy-dispersive X-ray (EDX) techniques were also used to evaluate the corrosion processes and compare them with atmospheric exposure specimens. EIS was found to measure the corrosion associated with on-vehicle exposure, thus providing an excellent screening technique for evaluation of the performance of EG automotive sheet steel.

Jan 1, 1990

By Alan A. Campoli

The U.S. Bureau of Mines evaluated two different conventionallongwall gate entry systems in the Southern Appalachian Basin, where mining and geologic conditions are conducive for coal pillar bumps. These gate entry systems were in a coal mine located in the Pocahontas No.3 Coalbed under approximately 2,000 ft of overburden and a massive quartzite sandstone member, and both employed a center abutment pillar flanked by yield pillars. The 8O-ft-square tailgate abutment pillars within the first study area began bumping 500 ft in advance of mining. This was accompanied by face bumps on the tailgate corner of the longwall face. The 120-by 180-ft tailgate abutment pillars within the second study area did not begin to bump until mining was approximately 100 ft past. Coalbed stress change and abutment pillar dilation data demonstrated that a 15-ft-wide perimeter of yielded coal surrounded a highly stressed core in both sizes of abutment pillars. The 62 pet more core area per foot of gate entry in the larger abutment pillars prevented excessive load transfer to the corner of the tailgate panel and eliminated the face bumps experienced with the original gate entry design.

Jan 1, 1990

By John J. Sammarco

The U.S. Bureau of Mines seeks to increase safety and efficiency in U.S. coal mines. One approach is to develop technology for automation of a continuous mining machine. Realization of an autonomous mining machine requires development of subsystems for machine intelligence, navigation-positioning, and computer control. This report focuses on investigation of one subsystem, an onboard heading system, which would be responsible for determining and controlling machine heading. The onboard heading system investigated is a multisensor system to determine machine heading, pitch, and roll. A directional gyroscope provides heading (yaw), fluxgate sensors provide a compass heading, and gravity-referenced clinometers give machine pitch and roll. The system utilizes a dedicated microcontroller networked to an external system of computers. Tram commands, supplied to the network from external computers, are executed by the onboard system. Sensor feedback is employed for closed-loop control of machine heading by controlling pivots and turns. The report discusses operating limitations and error sources of system sensors and presents test results of closed-loop control of machine heading. Results of tests with a mining machine are used to exhibit various sensor shortcomings and to evaluate control of pivots and turns.

Jan 1, 1990

By Thomas M. Barczak

The U.s. Bureau of Mines is conducting research to optimize the utilization and design of mine roof support systems. This report describes methods to evaluate resultant loading on longwall shields, defined as external resultant vertical and horizontal force acting on the canopy and base. Four models are considered: two rigid-body models, an elastic model, and a numerical model. The rigid-body models equate measured internal shield forces to unknown external resultant shield forces (loads) through rigid-body analysis of static equilibrium requirements. The elastic model develops a solution to shield mechanics by evaluation of the load-displacement relationship and stiffness characteristics of the support structure. The numerical model is a two-dimensional finite-element representation of a shield structure. Model determination of resultant shield loading is compared to controlled loading of a shield in the Bureau's mine roof simulator. Parameters investigated are shield height, canopy contact configuration, canopy and base horizontal constrainment, and boundary conditions imposed by vertical and horizontal shield displacements. It is concluded that rigid-body models are most applicable to in situ measurement of shield loading. Applications requirements and potential error sources are discussed.

Jan 1, 1990