Search Documents

In North-West Nelson the Riwaka Complex, a linear basic intrusive complex, is exposed for approximately 45 km. Some 500 km south, across the Alpine Fault, a linear zone of similar but less well known basic intrusives that may be correlatives of the Riwaka Complex is exposed discontinuously for about 80 km. The Complex was emplaced at several centres along a major tensional fracture zone that developed in upper Carboniferous to Lower Permian time. This fracture zone probably formed in response to the development of a west dipping subduction zone that gave rise to the Permian volcanic arcs in east Nelson and western Southland. The Riwaka Complex contains three rock suites. The Fractionation Suite, characterized by cyclic mineral layering and small scale cumulus banding is the largest and is divided into the Ultramafic, Hornblende and Plagioclase Series, each of which is subdivided into several units. The Cumulus Gabbros represent a restricted but important suite of unusual composition, while the third suite is the late phase Diorite Suite. Except in the lower units of the Ultramafic Series sulfide mineralisation is widespread. Pyrrhotite is the dominant sulfide with lesser chalcopyrite pentlandite and pyrite. Four significant zones of sulfide accumulation are recognised and discussed in some detail. Evidence suggests that the primary magma from which the Riwaka Complex was derived was sulfur deficient. It is concluded that the sulfur content of the Riwaka Complex was derived from assimilation of sulfur rich wall rocks during intrusive processes.

Jan 1, 1980

By Michael E. Berndt

Asbestos first became an issue to Minnesota?s iron industry when it was revealed that mineral fibers similar to those in Reserve Mining?s tailings were being found in drinking water for several communities that used Lake Superior as their primary water source. This discovery turned what had largely been an environmental court battle into a case concerning public health. The courts listened to much conflicting and uncertain scientific testimony on the size and distribution of the mineral fibers and on the potential health effects imposed by them. In April 1974, the plant was ordered to shut down by a federal judge but the company quickly appealed the decision. The appeals court granted a stay and ultimately ruled that the plant?s closure could not be justified based on the unknown health effects of the mineral fibers since the consequences of such an action would have immediate and severe social and economic impacts. The plant was allowed to continue operation, but ordered to abate emissions to air around the plant and to switch to a land-based tailings disposal system. Much of the scientific uncertainty and public concern over mineral fibers in Minnesota?s taconite industry remain today. ©2007 Elsevier Inc. All rights reserved. Keywords: Minnesota; Iron ore; Taconite; Asbestos; Amphibole; Reserve Mining; Tailings; Mesabi Iron Range

Jan 1, 2007

By A B. Christie, F P. Bierlein

Lode gold deposits of the Western and Eastern provinces, South Island, New Zealand , formed as a part of the Cordilleran-style tectonism during Tasman/Tahua and Rangitata orogenesis along the Paleozoic-middle Mesozoic southern Gondwanan margin. These deposits, hosted by lower grade greenschist facies sedimentary rock sequences of the Buller, Takaka, Torlesse, and Caples terranes, universally show geological features that are consistent with the orogenic gold deposit model, and genetic features are generally suggestive of a metamorphic origin, with the possible exception of a magmatic fluid source for the mineralisation at Sams Creek. However, ore fluid chemistry in Mesozoic deposits of the Eastern province, particularly the low concentration of non-aqueous volatiles and the very dilute nature of the fluids, is uncharacteristic of most orogenic gold deposits; this must be explained by either a unique fluid source or fluid type, which we believe unlikely, or an unrecognised significance of relatively rare gas-rich fluid inclusions in the deposits. Absolute age data for gold deposits in both provinces remain equivocal, thus hindering definition of the exact temporal relationship between ore formation and terrane accretion, regional metamorphism, and magmatic arc emplacement. Mercury and antimony occurrences in subgreenschist grade parts of the Haast Schist may target the upper levels of unrecognised orogenic gold deposits. If low-grade, high-tonnage intrusion-related gold systems occur on the South Island, then they are most likely to be discovered in association with the small molybdenite-, scheelite-, or cassiterite-bearing quartz stockworks spatially related to the Karamea and Median batholiths.

Jan 1, 2005

By Randal J. Barnes

A system, such as a mine production system or a mine ventilation system which includes the movement of commodities or some material between decision points may, in many instances, be effectively modelled as a network. Mining has often been characterized as primarily a materials handling function. To a great extent this is true, even though it is an over simplification of all the activities involved in a mining operation. Accepting the materials handling characterization of a mining operation permits the extension of the characterization to a flow process. That is, the ore flows from the mining face through the mining phase (excavation & loading, hauling, dumping) through the milling phase (crushing, grinding, recovery) through the smelter phase and finally to marketing. With this concept it is possible to depict a mining operation as a simple network. For example consider an operation consisting of two mines (A and B) with mills at each mine (MA and MB) with the possibility open to treat ore from mine b at mill NB, but it is not feasible to treat mine B ore at MA. The product of both mills is sold.

Jan 1, 1983

By Howard N. Eavenson

TWO months ago, just after the coal code hearing in Washington, one of our leading liberal weeklies printed a study of the coal industry made by an economist in the Administration, and on the outside cover bad it featured as "Coal-A Dying Industry." There are, of course, different opinions as to the accuracy of this characterization and I want to present some of the facts about the outlook for the bituminous industry for a short time ahead. In view of what has happened in the industry within the recent past it would be futile to attempt to make any prophecy about what is likely to occur in the future. We all know that a prophet is not without honor save in his own country, but it is likely that anyone undertaking this role about this industry would soon find himself in no man's land. One can, with some slight degree of safety perhaps, outline present conditions and tendencies and draw some inferences as to what the future may hold.

Jan 1, 1933

The copper concentrate market is becoming increasingly unstable. In the early 1990s large concentrate stocks were built up and the glut was cleared only after treatment charges rose so sharply that 'non-traditional' custom smelter capacity, such as in Kazakhstan, could be employed, By 1994 the market had shifted and Western smelters were unable to secure enough concentrates to operate full out. The reason for these sharp swings in the market balance is that virtllally all the recent mine development has been non-integrated. With different companies developing new mine . and smelter capacity, it is inevitable that the pace of expansion in the two sectors will not be coordinated. For many years the Japanese smelters were the major buyers from the new mm-integrated mines. However, Japanese smelter capacity is unlikely to increase appreciably in the future and this stabilizing influence will be very difficult to replace. This paper will examine the likely concentrate/smelter balance over the next five years and will forecast the likely direction of? treatment charges. It will also touch on the critical variables in assessing the viability of new greenfield custom smelter capacity, such as proximity to concentrate sources, by-product sulfuric acid prices and, most importantly, tariff protection.

Jan 1, 1995

By Faruk Oksuz

The owners of large infrastructure projects are challenged on how to implement sound engineering and construction contracting strategies that address their prime expectations: a quality job, on time and within budget. With the increasing number of large engineering and construction projects worldwide, owners continue to search for alternative contracting strategies to address their risk, quality, sustainability (operability and performance), schedule, and budget concerns. Coupled with the shortage of resources, delays, political pressures, and other obstacles in procurement and negotiation processes, engineers and contractors are also looking for creative ways to optimize contract packaging strategies for efficient and successful project delivery. This paper compiles an array of decision making criteria and suggests a balanced evaluation, ranking and selection strategy in procurement of both engineering and construction services for large tunneling and other infrastructure projects. A number of owners? general preferences and viewpoints are discussed on large tunnel programs encompassing water and wastewater conveyance systems, pump stations and treatment facility upgrades. Contract packaging strategies and project phasing and segmenting alternatives for preliminary engineering, final design, construction management, and actual construction of facilities are featured for several large water and wastewater infrastructure projects. While the selection (and the relevant selection process and criteria) and performance of service providers, whether for engineering or construction, have profound effects on the outcome of any given project, this paper only examines strategies for con-tract packaging. More specifically, the authors evaluated case studies and developed a range of recommendations for packaging of large water and wastewater infrastructure projects with multiple components.

Jan 1, 2008

The oxidation of ferrous sulphate to ferric sulphate with air and oxygen in a gas lift percolator was investigated with initial Fe2+ concentrations in the range 0·01 M to 1·0 M,temperatures in the range 20-80°C, and pH in the range oto 2.The rate of formation of Fe3+ was found to be well described by the rate expressionEquation 1and a consistent mechanism is proposed.The presence of Cu2+ was found to cause an increased rate of oxidation, the effect being greater with Cu2+ concentrations increasing in the range 0·001 M - 0·01 M in 0·2 M Fe2+. The effect of other solutes containing Ni, Zn, Mn, Co, Hg, Cl, Mo, NH4, As, Cr, or Na at a concentration of 0·001 M in 0·2 M Fe2+ was negligible.

Jan 1, 1972

By Baker G

The exposures resulting from development work, following on the discovery of a new shoot of hIgh grade ore at the north end of the Sardine tin mine, during 1952, have provided an unusual opportunity to study the oxidation of a stannite-rich ore. Through the kindness of C. C. Morton, Chief Government Geologist of Queensland, an exactly located suite of specimens representative of the exposures was supplied by J. and W. Reddie. This was later supplemented by a number of specimens culled from a parcel ofrepresentative ore submitted to the Melbourne Ore Dressing Laboratory for testing.The Sardine tin mine, near Ewan, Queensland, has been the outstanding producer of the Kangaroo Hills Mineral Field. Since its discovery in 1918, up to 1952 it has yielded about 1,500 tons of cassiterite concentrates, and about 85 tons of stannite concentrates. The outcrop ore averaged 35% tin oxide, but the grade declined with increasing depth, and by 1930 had fallen to 7% tin oxide. In the northern section of the mine the ore shoots show a downward passage to complex primary s.ulphide ore, containing cassiterite and abundant stannite.The orebodies occur in a series of fissures in a crushed zone about 50 ft. wide in slates and quartzites that have been intruded by granite (Connah, 1952). A quartz porphyry dyke forms the footwall of the original main lode in its southern part, being traced' from the surface to' the No. 4 level (173 ft. vertical depth), and two narrow dolerite dykes were encountered in the workings north of the main...

Jan 1, 1954

Thallium is an uncommon heavy metal that may be found in concentrations that exceed regulatory limits in mining influenced water associated with processing cadmium, copper, gold, lead, and zinc ores. This study evaluated cost-effective modifications to lime precipitation treatment to reduce thallium concentrations to below the EPA drinking water MCL of 2 ppb. The oxidative precipitation of Tl+ to Tlß+ by potassium permanganate was explored for thallium removal at low concentrations (1 ppm initial thallium). Laboratory batch tests were performed to evaluate the removal of thallium from synthetic solutions. Three ratios of potassium permanganate to oxidizable metals in solution were used (one-half, one and two times stoichiometry). Thallium was removed to less than 1 ppb for all stoichiometric ratios evaluated within 10 minutes of reaction. The efficacy of oxidative precipitation for thallium removal is presented.

Jan 1, 2011

This modern plant was installed with the object of treating all oxide ore and payable dump material by the cyanide process.The plant is located on a ridge on the eastern side of Linda Gully. The mill -site has a slope to the south of 1 in 4.The new plant is of steel and concrete construction and was specially designed to suit the climatic conditions which exist at Mount Morgan.THE COARSE CRUSHING PLANTThe ore received from the, mine is dumped into a 600-ton steel bin which is commanded by a 3 ft. 6 in. gauge railway,The mine ore is conveyed by steam locomotives in rakes of five self-dumping 7-ton railroad cars. The dump material is mostly loaded by bull-dozers and conveyed to the binsin large motor lorries. Located on the top of the bin is a heavy railroad grizzly having 12-in openings through which all ore must pass.The flow of ore from this steel bin is controlled by a No. 7D 3-speed Ross chain feeder. It should be mentioned here that, although the bottom of the steel bin is inclined at an angle of 45°, it has been found, owing to the clayey nature of the oxide ore, that the live capacity of the bin is only about 50% of the total capacity.

Jan 1, 1939

By F. Rosenblum, P. Spira

"Techniques were developed to determine the oxygen demand of sulphide ore pulps in the laboratory and in concentrators. The effect of variables which influence oxygen demand was studied, and it is shown that the oxygen demand is a measure of the degree of oxidation of the sulphide surfaces. It is suggested that in investigating the significance of oxygen in flotation, the oxygen demand of the pulp is a more suitable parameter than the dissolved oxygen content.Oxygen demand measurements are being carried out with a view to determining the effect of aeration on mill metallurgy and devising improved methods of predicting aeration requirements of sulphide ores.The importance of pulp oxidation in the flotation of massive sulphide ores has long been recognized. At the Noranda concentrator, chalcopyrite could not be floated satisfactorily without a pre-flotation aeration step because the necessary dissolved oxygen was consumed by the large amount of pyrrhotite in the ore. With aeration, pyrrhotite and pyrite were depressed by surface •oxidization, and the resulting thiosulphate level in solution gave a good indication of the end of useful aeration. 1'he present study was prompted by the need to find an alternative criterion for cases where recycled mill water may contain a relatively high concentration of thiosulphate. Preliminary experiments suggested that the rate of oxygen uptake by the pulp -its oxygen demand -might be a practical measure of the end point of aeration as well as a significant parameter in the flotation of massive sulphide ores.Although it has long been realized that oxygen is an important variable in flotation, analytical difficulties precluded detailed plant investigations. Measurements of' dissolved oxygen in mill pulps were first reported by Ralston(i) in 1929. A titration method was used, and because of the delay occasioned by the preparation of clear solution samples, the values obtained were believed to be low. It was quite evident, however, that pulps in the grinding circuit had a lower oxygen content than in flotation. More recently, Woodcock(2,3) used a polarographic probe to carry out oxygen surveys in six Australian concentrators and he generally observed a similar pattern. A large number of other solution parameters were monitored, such as pH, redox potential, reducing power, and reagent and metal concentrations, with the aim of detecting correlations among the measured variables. A few potentin.lly useful relationships were found ""or specific operations in certain plants."

Jan 1, 1974

By David Colloby, Darelle T. Janse van Rensburg

Premature coating failures of new and refurbished structural steelwork of clarifiers have been a common occurrence at power generation plant in recent years. Several of these failures have ended in disputes regarding which party was actually to blame for the early degradation of the coating system, i.e. quality of the power station?s water, poor application, substandard materials, outdated corrosion protection specifications, etc. Having investigated several of these premature failures, it is clear that the corrosion protection of clarifier steelwork is a highly complicated process and that the painting work needs to be closely monitored in order to ensure long-term protection by whichever product that is applied. The need for quality control inspections during the painting of the plant is often underrated during the project planning stage, also the importance of detailed corrosion protection specifications that consider not only the practical application of the materials, but also the quality control responsibilities of the Contractor, End User and Third Party Inspectorates that may be involved. This paper considers the application constraints of coatings to clarifier structural steelwork and importance of stringent quality control procedures in order to ensure the long-term performance of the corrosion protection systems.

Jan 1, 2006

By S. S. PRENZ

Discussion held at the sessions of the Canal Zone meeting, November, 1910. [SECRETARY'S NOTE.-As a result of this discussion, an expression of opinion covering all points of unanimous agreement was adopted and signed by members of the Institute party as individuals. This statement, which was printed in the Bulletin of December, 1910, is reprinted below, as an introduction to ,the detailed report of the discussion. It should be clearly understood that it does not constitute an official declaration by the Institute, the rules of which forbid any such action. At the New Haven meeting of February, 1909, a free discussion of the plan of the canal took place, in which the critics of the present scheme had full opportunity to state their views. That discussion was continued at considerable length in the newspapers ; but the Institute was never committed to either side. In this latter instance, the situation is precisely similar. Certain members and guests of the Institute, having had the advantage of later developments and of personal inspection, have expressed the conclusions at which they have arrived on their own responsibility ; and these conclusions are published by the Institute, subject to further discussion, like any other part of its proceedings. The general statement referred to contained a promise that the full discussion, of which it was a result, would be subsequently printed ; and this promise is fulfilled, so far as practicable, in the subjoined report, concerning which I beg to offer the following explanations: 1. It is made up of the remarks of the members of our party, as subsequently written out and mailed to the Secretary. 2. In editing these contributions, I have condensed the material considerably by cutting out much repetition of opinions and phrases ; and in such excision, I, frankly confess, the authors whose communications were delayed, have been the sufferers. Nevertheless, there is a good deal of repetition left, as there must be, when so many persons had talked so much, and come to agreement upon so many points. 3. It has been found impossible to preserve in this report the actual order of the free and informal oral discussion represented. Consequently the several contributions have been arranged in alphabetical order under the names of their authors. References to "preceding speakers," etc., must therefore be construed as referring to other speakers, preceding or following.-R. W. R.] S. S. PRINZ AUGUST WILHELM, AT SEA, November 14, 1910. We, the undersigned, members and guests of the American Institute of Mining Engineers, after a visit to the Isthmus of Panama, and inspection of the work of the United States Isthmian Canal Commission, and after full discussion of our individual impressions, find ourselves in unanimous agreement as to the following conclusions:

Jan 1, 1911

By MERLE HOWARD GUISE

WHEN I was a boy I walked into Fairbanks in 1905. I was but a soft chechako, and arrived with blisters covering my feet, as a result of "mushing" the 400-mile trail on foot. Because of them, the display windows of the trading posts were first to catch my eye-dog and horse collars, harness and sled parts! And because of my enthusiasm for things adventurous, I looked long upon the prospectors' gold pans, shovels, rifles, camp equipment, and what not. Today those windows are filled with motor car accessories, tires and repair parts; yes, even thermos bottles and vacuum cleaners! There were many chance meetings with little parties of prospectors in my youth, and it always set my blood to tingling. Sometimes it was a 70-year-old sun-baked son of the Arizona desert, wrangling his stubborn, faithful jenny away from some outfitting store, at others a shovel-ended poling b0at in northern Canada, \vith the partners and the dogs towing upstream along the bank, or an old sourdough, with tug-rope around neck and hand on the spruce sapling gee-pole, mushing along behind his two or three old, plodding malamutes, dragging a little Yukon sled piled high with rusty sheet-iron stove, pick and shovel, cross-cut saw and axe, rifle, bales of dog salmon, and other paraphernalia. These meetings envisioned the panning of old creek beds and draws in the search for as yet undiscovered pay-channels; they meant the toughest kind of work sinking a hole to bedrock in some far-away valley of promise; they suggested wood fires to thaw the frozen muck and gravel and crude windlass and hand-made tub to hoist the water and the mud; but loudest of all they spoke of Adventure.

Jan 1, 1929

By K. Collett

Elandsrand started shotcreting back in 1991. This paper will share the experiences of the mine by looking into the past, the present situation and the way Elandsrand plans to approach the future. It looks at the application of drycrete and discusses the factors that led to the introduction of wet fibre reinforced shotcrete. The logistical constraints of getting shotcrete material underground will be solved by the development of an underground batch plant, using run of mine waste rock as an aggregate.

Jan 1, 1998

By C. H. Burgess

ON June 5, 1947, Secretary of State George C. Marshall in a speech at Harvard University outlined a plan for the economic recovery of Europe. The plan contemplated that the United States should provide assistance which would enable the European nations better to help themselves and to help each other to reconstitute from their war-torn lands conditions which would make possible decent standards of living.

Jan 1, 1950

By R. T. Swinderman

"Virtually every article you read on safety has a statement to the effect: “It’s obvious that safety pays”. If it is so obvious, why is it so hard to answer these questions? • How does the Maintenance or Operations Manager convince the Plant Manager to spend money from the annual budget for safety improvements? • How does the Plant Manager influence Corporate to prioritize safety improvements? • How does an engineering firm persuade the owner to spend more on design and equipment up front to reduce risk? There are many cultural and structural reasons why it is so difficult to prove the obvious. In my opinion the main culprits are: the almost universally used ‘Low Bid’ process, variations in reporting incident statistics between industries and countries, and, the Generally Accepted Accounting procedures (GAAP) [or International Financial Reporting Standards (IFRS)]. Conventional wisdom is it’s smart not to spend more than you need to meet the minimum regulations and maximize production. But buying on price alone often harms people, degrades the environment, and reduces the company’s bottom line. How can this be? You met the minimum safety requirements and saved money by buying on price. Don’t those savings go right to the bottom line? When you buy on price you get minimum quality, minimum compliance and are often backed corner with no reasonable options to rectify the problems that arise from buying on price instead of buying on long term life cycle cost. Culturally few companies actually ‘walk the talk’. It is trendy to have giant billboards at plant entrances proclaiming world class compliance with quality and safety standards. Annual reports are embellished with safety slogans and sustainability statements. Behind the front gates and the glossy annual reports the message is clear: produce or be replaced. Only a few companies go beyond the window dressing and actually endorse, from the top down, continuously improving their safety culture. Those that do embrace safety, show significant performance advantages over their competition that are reflected in their safety, productivity and environmental records and, ultimately their financial statements and share price. Current accounting (and reward) systems make it unlikely financial managers will accept non-conventional approaches to justifying expenditures on safety because they are driven to report “hard” numbers that can be documented and are within the “GAAP or IFRS Rules.” But in reality, accountants quantify soft or intangible costs all the time in their financial statements. Justifying safety investments is greatly enhanced by quantifying what most financial managers would call intangible costs. Government agencies have no problem assigning intangible costs to justify regulations to improve safety. How many times have you heard that the regulation is justified because the cost to industry is X while the benefit to the society is 2 or 3X? How can they say that without including intangible costs? We find it hard to believe these government claims of benefits to society because we have been trained to think about saving hard direct costs to justify investments."

Jan 1, 2017

By John G. Payne

The Pebble deposit contains three contiguous zones. In the Pebble West zone, granodiorite stocks intrude gently warped volcanosedimentary rocks that had been intruded by diorite sills and two felsic intrusion breccias. In the Central zone, volcanosedimentary rocks are cut by diorite and granodiorite sills; the latter are genetically associated with the granodiorite stocks. In these zones, widespread potassic alteration consists of brown biotite and K-feldspar, with abundant quartz-carbonate-sulphide vein stockworks. Chalcopyrite/pyrite ratios range from 2/1 to 1/20. Diorite hosts the highest-grade mineralization, with much of it being disseminated. Patchy, later phyllic alteration is moderate and commonly depleted in copper. The Pebble East zone occupies a granodiorite stock and intruded host rocks below an eastwardly thickening wedge of barren Tertiary volcanic and sedimentary rocks up to 600 m thick. Brown biotite alteration and copper mineralization are strong, with chalcopyrite/pyrite ratios commonly over 1/1. The zone extends to a depth of at least 1200 m below surface; some drill holes bottomed in strong mineralization. Later, weak to moderate sericitic alteration removed some chalcopyrite and locally remobilized gold. The Pebble deposit has a Measured/Indicated resource of 3 billion tonnes grading 0.28% Cu, 0.32 g/t Au and 0.015% Mo (= 0.5% copper-equivalent) and an Inferred resource of 1.13 billion tonnes grading 0.30 g/t Au, 0.27% Cu and 0.015% Mo (0.55% copper-equivalent). The Pebble East zone has an Inferred resource of 2.13 billion tonnes grading 0.55% Cu, 0.34 g/t Au, and 0.037% Mo (0.97% copper-equivalent). The Pebble East zone is open to the east and to a lesser extent to the north, south, and to depth.

May 1, 2006

By K. P. Wang

Mining and metallurgy have had a long history in China, and resources there have always been considered promising. Under the People's Republic of China (PRC), a remarkable industrial renaissance is underway that should further gain momentum in the years ahead. Rapid development of minerals have not only brought the PRC prominence in industrialization, but also in world affairs. Chinese mineral developments, especially petroleum, have been increasingly in the news. Oil and gas may have great potential, but a very large coal industry is already in existence. The steel industry ranks fifth or sixth in the world. The PRC is also prominent in fertilizer, cement, and salt production. The export metals are well known. Also, the country is buying heavily in nonferrous base metals. The need to know and the intense interest in the subject have prompted this study. The world significance of Chinese minerals is pointed out. The history of growth and PRC's mineral supply position are reviewed. Evaluations are made of policy considerations and regional and technical factors affecting mineral development. PRC's mineral trade and efforts to obtain equipment, supplies, and know-how are assessed. Specific reviews are made of major mineral sectors, including coal and power, oil and gas, iron and steel, nonferrous metals, industrial minerals, and fertilizers and chemicals. The overall outlook is summarized.

Jan 1, 1975