Search Documents

By Joshua Micah Hoffman, Jhon Silva-Castro, Kylie Larson-Robl

A coal mine impoundment failure has the potential to be environmentally devastating and life-threatening. It is well documented that after seismic events slope failures in impoundments can occur. It has been concluded that often the main driven factor of the failure is the increase in excess pore pressure due to ground vibration. A small amount of research has been done regarding the stability of coal mine impoundments under natural seismic events; however no research has been done considering vibrations from mine blasts. If it is taken into account that current environmental restrictions oblige to increase the capacity of coal mine impoundments, thus increasing the hazard of such structures, it is necessary to evaluate the effects of near-by mine blasting on the stability of the coal mine impoundments in order to mitigate and control the potential of slope failures. To study the behavior of excess pore pressure under blasting conditions, scaled simulations of production blasting events were set up inside of a controlled sand tank. The research was divided in two stages. The first one was done, using dry conditions, while in the second part, the same set of tests were performed under saturated conditions. This document shows the partial results for stage one (dry conditions). For the tests, explosive charges were set off within the sand tank at various distances to simulate different blasting distances. Information was collected from geophones, accelerometers, microphones and high speed video camera for dry and saturated scenarios and additionally from piezometers under saturated conditions to assess the behavior of the material under blasting conditions.

Jan 1, 2015

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

An avalanche is a snow slide. A simple explanation is that the snow on a slope will slide (avalanche) when the snow strength can no longer support its own weight. Snow avalanches happen when the load from snowfall or ram on a snow slope increases faster than the stre n g t h of the bonds between snow crystals. Avalanches can also happen when the strength of a buried layer decre a s e s . Active avalanche control is the intentional triggering of slides. Washington State Department of Tr a n s p o r t a t i o n (WSDOT), does avalanche control to minimize the chance of natural avalanches into traffic. Avalanche control work is done all over the world by: highway departments, ski resorts, railroads, mining operations, utility companies, and other activities threatened by avalanches. The majority of active avalanche control is done with skis, by explosives, or exploding projectiles. Blasting techniques and practices have evolved to fit the specific needs of avalanche contro l . Passive avalanche control is the use of engineered s t r u c t u res such as snow sheds, bridges, or snow supporting devices, to permanently protect a specific location from avalanches. The problem is that these struct u res are extremely expensive. There are a variety of passive avalanche control measures as well as the active m e a s u res used to protect the highway over Snoqualmie Pass. As traffic volume and use expectations incre a s e , m o re extensive passive measures will be needed to keep avalanches from affecting the highway.

Jan 1, 2004

By Richard Goodridge, Stephen Thomsqn, S Rodgers, D Tunaley

The mining, quarry and construction industries are facing’new challenges everyday. These challenges can be imposed by economic objectives or through external factors such as extreme geological conditions. Simultaneously, all mines, quarries and construction sites are facing more and more stringent environmental requirements.

Jan 1, 1998

By Steve Dillingham

The horrific events surrounding September 11th left Americans with a feeling of sudden helplessness...the shock of being unprepared and powerless. From this tragedy, we can understand the need to prepare for the unexpected, and can apply this hard lesson into operational planning for those involved in the commercical explosives industry.

Jan 1, 2003

By Dale Preece, Stephen Chung

Blasting induced rock fragmentation is an art that has been developed and refined for hundred’s of years through blasting and recording the results. Good blasting fragmentation practices were thus developed through experience. However, this method requires a history that is typically developed in a mine over a number of years and sometimes at considerable expense. Quantification of fragmentation as a function of rock-mass characteristics and blast design is attractive. Developments towards this end have included semi-empirical methods as well as computer codes that explicitly treat shock wave transmission and the subsequent rock breakage. This paper will present predictions of fragmentation resulting from rock blasting using the computer code AUTODYN and a new state-of-the-art material model for brittle rock and concrete.

Jan 1, 2003

By Jean-Sébastien Lambert, Joseph Kabuya, Richard Simon

Managing a highwall failure risk in an open pit mine by controlling and mitigating the impact of vibrations produced by blasting operations is key to achieving safe and cost-effective operations. The impetus behind this study was the risk of multiple bench failures in an open pit mine that was detected by Slope Stability Radar (SSR) following blasting at the foot of a highwall. The unstable high wall was over 140 meters(459.3 ft)high and 200 meters(656.2 ft)wide. The quantity of associated material was estimated at 3,000,000 metric tons(3,306,934 US tons). The overall slope angle was 44 degrees. In order to continue mining without causing the highwall to fail, this study was initiated as part of a risk management plan to mitigate this major risk by identifying mitigation measures related to blasting operations and assessing the response of the rock mass to each blast. Identifying blasting mitigation measures consisted of optimizing blasting parameters to avoid failure of the highwall. First, a signature hole operation was carried out to obtain seismic records that were georeferenced and associated with known single charges. The method used made it possible to determine the propagation velocity of the P-waves associated with the various lithologies studied and to calculate, from the geomechanical properties of the rock masses, the maximum peak particle velocities to be respected. Subsequently, the targeted area of operation was modelled with the I-Blast software in order to optimize the firing sequences to be used according to the different lithologies present. The model also made it possible to optimally predict the particle velocities associated with each blast and ensure compliance with the previously determined peak particle velocity limits. The assessment of the rock mass’s response using SSR consisted of defining alarm thresholds and an intervention plan for various possible alarms as well as quantifying the damage to the highwall from blasting. Controlling the impact of blast vibrations on the highwall’s stability was successful, as the mitigation measures used during mining did not accelerate the highwall’s movement. No upward trend in the stabilization time of the rock mass was observed by the SSR after each blast. Post-blast geotechnical inspections and analysis of post-blast deformations in the highwall also did not reveal significant damage to the highwall as a direct consequence of the blasting.

By R. Franfield

This paper describes a situation that many drilling and blasting contractors have found themselves in – a client?s fear of the use of explosives. In the summer of 2007 Blasting Services Ltd was asked to undertake some drilling and blasting work in an abandoned quarry that was being restored for a housing development. Previous quarrying operations had left a series of overhangs that were considered unsafe and required removing. The site contractor considered that the best and safest way to carry out this work was by drilling and blasting. Blasting Services Ltd, with the technical assistance of Exchem Explosives, designed a drilling and blasting regime to accomplish this work with a series of trim blasts. The design took into account the close proximity of a structure in very poor condition and the imposed vibration limit of 6.0 mm/s (0.24 i.p.s.). The faces were profiled, holes drilled and explosives ordered. A few days before the first blast was due to be carried out the client decided that the poor condition of the nearby structure meant that the use of explosives could not be permitted. This decision was made despite the blast design indicating that the vibration level would be well below the 6.0 mm/s (0.24 i.p.s.) limit.

Jan 1, 2009

By Edward J. Karkoska

The film you see is a slow motion view of a typical half million ton taconite blast at one of Erie's mines. This blast is made up of 220 drill holes and a total of 325 thousand pounds of blasting agent. The second view of the same shot is taken by a remote control hi speed camera located 1500' directly in front of the blast. Shortly you will see some violent camera movement as the air blast shock wave strikes the camera location. As the blasting sequence progresses the rock fly becomes evident, and if you will look closely amidst the clouds of smoke, rock fragments weighing up to 1/2 ton begin to cascade into view. These missles are the chief concern of blast security. The next camera shot at 4000 frames/second vividly describes the primacord firing lines detonating the blast. Travelling at 22,000 ft./sec., this white snake of fire travels to each hole, detonating the blasting agent. Before we get into the matter of blast security, let me locate our operation for those of you not acquainted with Minnesota's iron ranges and tell you something about our company.

Jan 1, 1969

By Frank Sames

Most Blasting Programs are developed focussing on the environmental impact with respect to blast vibration and airblast. Compliance with existing regulations or policies limiting the immissions are generally achieved through constrains in the blast design, or monitoring programs. Efficient monitoring programs combine compliance monitoring and blast assessment. Signals, which are obtained in the area of direct influence of the seismic source, can contain valuable information about the blast design parameters. Techniques to analyze blast vibration signals have advanced and can assist in understanding the contribution of individual blast parameters to blast vibration and airblast. Advanced signal analysis encompasses magnitude analysis, Fast Fourier Transforms (FFT) and frequency scans in the frequency domain, as well as filtering in the time domain. Through examples, the advanced signal analysis techniques and their limitations are described and discussed, showing the impact of blast timing, timing accuracy, charge configuration and the geology dependent transmission behavior. Optimization criteria and pragmatic monitoring programs can be developed on the basis of the most influential blast parameters. In addition, however, safety and the cost efficiency of the blasting program are essential to the success of an operation. That is where advanced signal analysis techniques can interface with blast planning, computer assisted modeling and information systems. A valuable process can be developed to ensure compliance with existing regulations and efficient risk management for mining operations, while tracking cost and supporting operational decisions. A conceptual blasting information system is presented.

Jan 1, 2000

By Kenneth Eltschlager, Jim Ratcliff, Michael Mann, Edward Sheehan

The Appalachian Blaster Certification Delegation initiated a study to compare the consistency of measurements from blasting seismographs. Six blasts were monitored at surface coal mines in West Virginia, Maryland, and Ohio. A total of seven different makes were deployed during the tests, with as many as seven models from five different manufacturers compared during any one blast. Great care was taken to bury the geophones in identical fashion. The variations in seismograph readings were compared to the International Society of Explosives Engineers’ Performance Specifications for Blasting Seismographs. Between 4 and 125 Hertz, the ground vibration amplitudes should be within ±5% and airblast amplitudes should be ±1 decibel. For each of the three mutually perpendicular ground vibration channels and the acoustic channel, the median value of all the units was used as a baseline for comparison. The six blasts monitored had median peak particle velocities ranging from 0.42 to 3.47 inches per second (in/s) (10.7 – 88.1 mm/s) and median airblasts ranging from 124 to 135 decibels (dB). There were 46 seismograph recordings for the six blasts. Eighteen (39%) of the 46 maximum peak particle velocities varied more than ±5% from the median. A total of 138 (3 × 46) component particle velocities were recorded, with 50 (36%) of the readings varying more than ±5% from the median. For airblast comparison, 43 recordings were obtained, with seven (16%) varying more than ±1 dB of the median. Variances may be attributable to blasting seismograph differences, variations in field deployment, and relative locations of the geophones. Full waveform seismic and acoustic overlays for individual blasts showed encouraging conformity with some slight anomalies

Jan 1, 2015

By Brad Bulow

Blasting is an essentially violent process aimed to disrupt and loosen rock for productive excavation. Some dilution of any ore present is the inevitable result. This makes blasting a dirty word to most geologists, particularly in narrow vein gold mines. A 1% increase in gold recovery may be worth $1 M extra revenue to a large mine.

Jan 1, 2000

By P Geddes, K Grohs, C K. McKenzie, M Morrish

Low grade surface gold mining at the Acacia Resources, Union Reefs Gold Mine in Australia's Northern Territory, involves the excavation of benches in three slices after blasting. Blast patterns span zones of high and low grade ore, as well as zones of waste, and selective excavation is required in order to maintain economical head grades for the carbon-in-leach processing plant.

Jan 1, 1998

By Thierry Bernard, Pierre M. Vuillaume, Michel Kiszlo

"In the context of its studies for the trench ministry of the environment and for the French national coal board, INERIS (the French institute for the industrial environment and hazards, formerly CERCHAR) has made a complete critical survey of the methods generally used to reduce the levels of blastingvibrations."

Jan 1, 1996

One of the most common critical areas of longwall mining in terms of ground stability are the gateroad and bleeder entries. These critical entries provide much-needed safe access for miners and allow for adequate ventilation required for dilution of hazardous airborne contaminants and must remain open during mining of a multi-panel district. This paper focuses on the stability of the longwall entries subjected to a single abutment load such as bleeders, first tailgate, and last headgate. First tailgate and last headgate are also referred to as blind headgates and tailgates. A study of a longwall district through conditions mapping, support evaluations, and numerical modeling was conducted and evaluated by researchers from the National Institute for Occupational Safety and Health (NIOSH). The condition mapping and support evaluations were performed on entries that spanned the previous five years of mining and relied on a diverse selection of supports to maintain the functionality of the entry. Numerical modeling was also conducted to evaluate various support types with further investigation and comparison to the condition mapping. The study demonstrated the importance of the abutment load decay versus distance from the gob edge, the potential for a reduction in material handling related injuries, as well as optimal usage of secondary and standing support.

Jan 7, 2020

It is no longer satisfactory to assess the value of a coking coal on its intrinsic properties alone; its value depends upon its behaviour as a component in a blend. No single test can be used to make this assessment, it can only be made by carrying out a suite of tests. The quality parameters which are considered desirable, and which have widespread acceptance, have been discussed and their application to the blending of coals from New South Wales and New Zealand has been reported and discussed. Blending can be utilised to offset deficiencies, or capitalise on advantages, of the individual coals making up a blend. Coals can be blended, which alone are poorly, Coking, but which have compensating features. Blending also allows better exploitation of coking coal reserves. Several applications of blending have been reviewed with regard to coal producers and exporters, as well as coal users. The possibility of extracting a coking coal fraction from fuel coals is discussed. Blending systems and the coking of coal are also briefly reviewed.

Jan 1, 1971

By Ray L. Tobie, Douglas E. Julin

GENERAL DESCRIPTION Block caving is a distinct caving method applied mostly to large, massive, ore bodies because of its in¬herent low cost and high production capabilities. Areas of sufficient size are removed by undercutting so that the mass above will cave naturally. Drawing of the caved ore at the bottom of the ore column causes the caving action to continue upward until all of the ore above the undercut level is broken into sizes suitable for handling. When properly applied, block caving results in a lower mining cost per ton than any other under¬ground method. There are three distinct forms: (1) dividing the horizontal area into rectangular or preferably square or nearly square blocks, drawing evenly over the entire area to maintain an approximately horizontal plane of con¬tact between broken ore and caved capping; (2) divid¬ing the horizontal area into panels across the ore body, retreating by undercutting manageable areas from one end of the panel to the other and maintaining an in¬clined plane of contact between the broken ore and caved capping (thus the name panel caving); and (3) no division of horizontal area of the ore body into defi¬nite blocks or panels (this is termed mass caving). Undercutting may be from wall to wall, retreating from one end of the ore body to the other, maintaining an inclined plane of contact between the broken ore and caved capping. The total active caved area is deter¬mined by the size of block that will not produce undue stress on workings below the undercutting level and by total production requirements. This type of operation is also referred to as panel caving at some properties. SUITABLE ORE BODIES Block caving in its various forms is applicable to deposits of various shapes and ores of various strengths. Its success is governed by rigid requirements and limi¬tations. In unsuitable deposits or where improperly em¬ployed, the loss of ore may exceed that of any other mining method. Good planning, systematic work pro¬cedures, careful supervision, and good judgment con¬tribute to its success. Ore Characteristics Included as a necessary characteristic in an ore body suited to a successful block-caving operation is a proper fracture pattern. Ore hardness should be another gov¬erning factor, and the toughness or softness of the ore should be considered. There must be sufficient horizon¬tal area available for expansion of the undercut, if neces¬sary, to start the caving process. Large, massive, ore bodies usually meet these conditions. Veinlike deposits must be wide and dip rather steeply to conform to the block-caving limitations. The capping must be of such a nature as to cave when the underlying ore is being removed since the weight of the overburden aids in crushing the ore. The most favorable capping character¬istic is that it breaks into coarse pieces and resists attrition as the block is drawn. Soft capping, by breaking into fine pieces and sifting into the ore or channeling through the ore to the drawpoints, can seriously dilute the ore and hinder the extraction of clean ore from the blocks. Types of Ore In block caving, a fairly uniform distribution of val¬ues in the ore is necessary. Grade values may range from low grade to high grade, but most often the sys¬tem is applied to low-grade ores. Wide veins, thick beds, or massive deposits of homogeneous ore overlain by ground which will cave constitute suitable ore bodies. The ore must be such that it can be supported while blocks are being developed and undercut but breaks up readily when caved. Some applications include porphyry copper, disseminated molybdenite, hematite in the Lake Superior iron district, limonite deposits in northern Spain, the diamond mines of South Africa, asbestos and nickel in Canada, and massive magnetite in Pennsylvania. Size and Shape Outline of the ore body should be fairly regular, and the sides of the ore body should dip steeply. It may not be economical to mine small portions of ore extending into the walls of the deposit, and low-grade inclusions in the ore cannot be left unmined. Some dilution of the ore, as mining progresses, by low-grade or barren cap¬ping is inevitable and, unavoidably, some clean ore is left between drawpoints. Determining Cavability The use of rock mechanics is sometimes advantageous in helping to determine the cavability of an ore deposit. The US Bureau of Mines has information and testing ability which can assist in determining the cavability of ore types. Several competent consulting orga¬nizations knowledgeable in rock mechanics can also as¬sist in evaluating the cavability of an ore body. Some recent work has been done to better define the cavability index of various ore bodies; an example of how this was determined is discussed by McMahon and Kendrick (1969). The intensity of the fracture pattern is a critical parameter to be analyzed. The question to be answered is, "How intense must the fracture pattern be?" Table 1 is a tabulation of the size of rock fragments that appear at the drawpoint of various block-cave mines around the world. These are indicative of the fracture-pattern spac¬ing and, as can be seen, they vary substantially from the almost sandy material at the Mather mine to fairly sizable blocks at the Grace mine. Several sets of fractures are essential to promote good caving. Ideally, two vertical sets at nearly right angles to each other and a third set nearly horizontal are required to insure a good caving ore body. Since initial caving of an ore mass is almost always by the action of gravity acting on these planes of weakness, it is doubtful

Jan 1, 1982

By R. M. Jara

This work evaluates and characterizes the impact of the support size and mining dilution of a block model in the operation and selection of equipment at an open pit mine. An exploratory analysis and geostatistical modelling of the grades assayed on a set of drill hole samples is performed, which allows constructing a grade model on a dense grid by means of a conditional simulation. The grades are then averaged to greater selective mining unit supports in order to proceed with the study and methodology. First, the metal-tonnage curves are used to analyse the loss of selectivity on the in situ resources caused by a change of support. Concerning the ore reserves and their mining sequence, defined in the pit optimization and analysis process, the same curves prove that the loss of selectivity is more accentuated. Second, the importance of the block boundary dilution produced during mining operations is assessed. Its value depends on the amount of ore in contact with waste, on the loading error of the equipment and on the ore loss/waste dilution criterion assumed by the planner. The dilution percentage and the differences between waste and ore grades become higher when the block size decreases. For these reasons, considering the dilution in the production plans makes mining a small support more constraining. An adequate delimitation of the orebody can improve the mining selectivity, leading to greater income. Finally, a study of the increase in mining cost that provides a zero difference in NPV between the different block size options is carried out, in order to determine the maximum increase in mining costs for which it remains profitable to mine at a smaller block size. Keywords: Mining selectivity, support effect, block boundary dilution, selective mining unit size, block model.

Jan 1, 2006

By S. Fuentes, J. Cáceres

"During the past fifteen years, mines utilizing the block caving method have improved performance and systematically reduced total mining costs.This paper describes improvements in mine design, mine planning, and mine management, including methods enabling the Chilean and international mining industry to ensure cost savings and productivity growth while using the block caving method. These improvements have encouraged the re-evaluation of underground operations at operating and closed open pits, and challenge surface mining applications as the only low-cost mining method. This paper describes a strategy to estimate the optimum open pit to underground transition time during the life of a mine. IntroductionDuring the last fifteen years, block caving mines have experienced huge changes in designs, planning and administration. These changes have permitted operators to drastically reduce costs, improve equipment productivity, and improve overall business performance. As a consequence of this situation, the block/panel caving mining system is challenging actual open pit operations to maximize the net present value (NPV)."

Jan 1, 2004

By R. R. Givler

Since the 1860's the good ole days, oil has been nozzle fed to burners under pressure atomizing the oil into droplets -- 1960's has produced vaporized oil that burns oil with the flame color and consistancy of gas -- If you can tell the difference by looking at the flame, gas or oil I?ll buy the lunch. First, we must ask, "Why all the excitement about Blue Flame?" This question is best answered by you after you have studied the principle of operation and see the result. I will attempt to explain both of these so that you can draw your own conclusions.

Jan 1, 1975

By Angela Binder, Mareike Schubert, Yichen Jiang, Sandra Nowosad, Oliver Langefeld

GermanyINTRODUCTIONThe mining industry is currently characterized by various factors such as environmental impact, resource scarcity, social responsibility and geopolitical uncertainty. The production of minerals required to meet the demand for renewable energy is expected to increase by 500 % by 2050, particularly for critical minerals such as graphite, lithium and cobalt 1. Easily accessible deposits are often depleted, meaning that deeper and more complex deposits need to be developed. Furthermore, investors’ value systems have shifted towards more sustainable practices. Alternative approaches to solving this problem are therefore currently being developed, such as the Modular Mining Systems concept for scalable and adaptable mining projects 2. Many mining companies have also taken important steps to become more sustainable, implementing measures such as proactive closure strategies, restoration programs and the development of renewable energy projects. In the European Union, laws such as the Critical Raw Materials Act and the Net Zero Industry Act support the mining industry 3,4. They see it as important for the energy transition and promote more sustainable ways of working in the industry Particularly negative environmental impacts such as land degradation, scarcity of local water resources, water pollution and greenhouse gas emissions are ingrained in society’s memory. Despite these efforts, the public image has not yet changed. To change this perception, the industry must strive to better communicate its sustainable practices and the steps it is taking towards a more responsible and sustainable future, promote transparency and build trust.Digitalization, automation and electrification are driving the digital transformation in mining. However, their implementation can lead to higher capital expenditure, limiting their adoption across the industry. Furthermore, implementing new technologies can be a daunting task for any organization. Change management comes into play when introducing such disruptive technologies. It involves preparing an organization for change, potential resistance and establishing effective communication. This helps to ensure that the implementation is successful and the benefits of the new technology are maximized. Digital transformation requires well-trained, young mining, electrical, mechatronic and software engineers with a deep understanding of information systems. Unfortunately, the industry faces the enormous challenge of attracting this younger generation, who have little interest in the extraction of raw materials. The need for action is compounded by an aging active workforce heading into retirement and the forecast of increasing demand for critical minerals.In this challenging environment, the concept of Blue Mining with its constant further developments represents a promising approach. This implies a shift from a linear to a sustainably oriented circular economy. For the mining industry, this specifically means the introduction of innovative technologies, the increased recovery of materials from waste and the consistent questioning and application of circular principles along the entire life cycle of a mine. Such a change can not only reduce the environmental impact, but also contribute to economic resilience and increased social acceptance of mining.

Feb 1, 2025