Search Documents

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal-preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cure all" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the-indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the comprehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer, or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made . . .

Jan 1, 1943

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal-preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cure all" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the com¬prehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made ...

Jan 1, 1943

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cureall" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the comprehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made.

Jan 1, 1950

By Cam Thomas, Steve Bernard

Various types of blasting instrumentation can be used in the field to analyze conditions before, during and after a blast, and to indicate what changes need to be made. When different types of measurements are combined together, the blaster can end up with useful data that can pinpoint the source or sources of problems and what changes have to be made. This paper outlines two case examples where blasting instrumentation was used to overcome problems in separate quarry operations. Extensive measurements with different systems led to significantly improved blasting results.

Jan 1, 2012

By D. F. Malott

The Michigan Department of State Highways makes extensive use of geophysics for subsurface surveying which would be applicable for uses in other fields. Examples of resistivity surveys are given which include a proposed large volume excavation with suggestions for land use after excavation, subsurface evaluation for engineering design, and a subsurface survey for land appraisal. An example of a combined refraction seismic and resistivity survey is shown where the resistivity is used for outlining the unconsolidated soils, while the seismic method Is used to outline bedrock and to evaluate it for rippability. A refraction seismic survey at the bottom of bridge caissons for evaluation of bedrock uniformity and a relative aid In assessing rock strength is reported.

Jan 1, 1968

By Robert W. Burns

Gentlemen, my subject today is glass reinforced plastics. By definition, this encompasses a wide variety of materials: at least a half dozen basic varieties of polyester, epoxy, and phenolic; virtually infinite compounding variations within the basic groups: literally limitless variations in the amount and the nature of the glass reinforcing. Complicating all of this is the fact that different modes of application of the same material fall appreciably alter' the product's general strength and suitability. These many, many differing materials are what we conveniently call "glass reinforced plastics" or, more simply, fiberglass". This common name is actually a large part of the problem when dealing with fiberglass materials. Far too often a specification is written calling for simply "fiberglass reinforced polyester', based on successful prior use of a polyester laminate. Such a specification is very nearly worthless since such tremendous variation is possible under it. Success of a laminate furnished under such a specification is entirely dependent on good fortune

Jan 1, 1962

By Patrick Cloutier

Presentation objectives ? Introduce discrete-event 3D computer simulation as a tool to design, improve and optimize construction projects: ? Describe a real typical construction project planning issue. ? Present an applied use of simulation to solve this issue. ? Detail benefits of using simulation versus traditional planning methods.

Aug 1, 2013

By G. H. Glos

There was a time when an occasional failure of a tailings embankment was considered an acceptable risk associated with mining activities. This is not the case anymore. A major tailings failure today could result in the indictment of mine officials, huge fines and a possible site closure due to the loss of operating permits. As a result of this changed operational environment, tailings disposal facilities must be operated with these potential consequences in mind. Physical controls for tailings embankments are prohibitively expensive. However, the nuclear industry has developed a system of administrative controls as an alternative to physical controls. Administrative controls may be defined as control of actions, through organizations and management, using written procedures, record keeping, review and audit to assure operation of a facility in a safe manner (10 CFR 50). Administrative controls can reduce the cost of operating tailings impoundments, as well as increase the level of confidence in these facilities.

Jan 1, 1999

Provide the mining industry with a simple, accurate and readily available means of measuring the gas flow from pipe outlets such as gob holes Approach The Bureau of Mines conducted laboratory studies to establish correction or method factors for anemometers when used to measure gas flow from pipe outlets. Using the Anemometer Anemometers are used by the mining industry to make air velocity measurements in mine entries. Although the instrument has no appreciable influence on the airstream in mine entries, especially since the cross-sectional area of an entry is much larger than the cross-section of the anemometer, correction or method factors are used to correct the center line anemometer velocity to average velocity. This adjustment is made because the air velocity in a mine entry is highest in the center and lower at the sides. Anemometers can be used to measure gas flow from small diameter pipe outlets; however, since the instrument diameter is much larger than one-sixth of the pipe diameter, it will influence the air-stream from these small outlets. Resulting velocity measurements are erroneously high by as much as 30 percent. Method factors must be applied to such anemometer measurements taken at pipe outlets. Through a research investigation the Bureau of Mines established a set of method factors for center-line anemometer readings taken at the discharge end of 4-to 8-inch diameter pipes. These method factors were combined with method factors which were developed by the National Coal Board of Great Britain for 12-to 30-inch diameter pipes. The anemometer was mounted on the end of a short rod and held against the pipe for support except on the 4-inch pipe where the instrument was started and stopped remotely to prevent hand interference with the air-stream during measurements. Method factors were determined by comparing the anemometer measurements at the pipe outlet to the true average airflow which was simultaneously determined upstream by venturi measurements. Consequently, a method factor is nothing more than the ratio of the true velocity to an anemometer measurement.

Jan 1, 1987

By X. Shi

This paper presents design and implementation details of a fuzzy-behavior-based controller for an automated excavator. The robotic excavator is equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered during the excavation process from bucket-mounted force sensors. Implementation details card experimental results using the fuzzy-behavior-based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining-excavator controller.

Jan 1, 1997

By B. L. Eggers

This study investigates the application of computed order tracking with subsequent rotation domain averaging and statistical analysis, to the drag gearbox of a dragline used in a mining environment. Computed order tracking is a fault detection method developed to deal with the varying speed conditions often found in industry and has been proven effective in laboratory conditions. Its application to real situations, however, requires some adjustment to deal with issues such as inadequate speed data and the fact that the drag gear rotates in two directions. This provides a unique opportunity to observe the performance of the order tracking method in a bi-directional rotating environment, allowing an investigation of the relationships between the results obtained from each operating direction. A monitoring station was set up aboard the dragline and data was captured twice daily for a period spanning approximately one year. The data captured consisted of accelerometer and proximity sensor data. The key on the shaft triggers the proximity sensors, allowing speed and direction to be measured. The measured speed is interpolated by using various speed interpolation techniques. Then the interpolated speed is used to complete the order tracking procedure that resamples the vibration data with reference to the speed. The results indicate that computed order tracking can be successfully employed in real environments. Furthermore it is shown that the rotation direction that opens the gear-tooth crack gives a better indication of incipient failure. It is therefore important not to disregard either direction when monitoring rotating machinery of this kind.

Jan 1, 2007

The importance of understanding the behaviour of cemented paste backfill (CPB) within the framework of the effective stress concept is highlighted in this paper. Only through an understanding built on this concept can problems such as barricade loads, the rate of consolidation and arching, be fully understood. The critical importance of the development of stiffness during the hydration process, and its impact on factors such as barricade loads, is used to illustrate why conventional approaches that implicitly ignore the effective stress principle are incapable of capturing the essential components of CPB behaviour.

May 1, 2007

By A. Farnoud

Thousands of miners, construction workers, and truck drivers are exposed to diesel exhaust particles. Diesel Particulate Matter (DPM) is a probable human carcinogen and stringent occupational and environmental standards have been established or are planned worldwide. Modifications in fuels and diesel engine designs have reduced emissions, but may not be enough to comply with the tightest standards. Post-combustion aftertreatment devices are likely necessary for many engine operators. However, even the most common and well studied aftertreatment devices fail from time to time. The objective of this study was to design, construct, and test an electrostatic aftertreatment device to treat DPM. An electrostatic precipitator (ESP) was designed and constructed to capture DPM from diesel exhaust, and different configurations were tested to optimize its performance. DPM was produced by a 6 kW diesel-powered electric generator and directed to the ESP through a short section of galvanized steel pipe after the muffler. Number and mass removal efficiencies were measured with a condensation particle counter (CPC) and by sampling through a stainless steel cassette and collecting the DPM on Teflon filters. Particle size distributions were measured with and without control using a 6-stage cascade impactor. The experiments were performed with the engine running at idle and also at medium load. The results show that our first generation ESP provides 60 percent mass removal efficiency, and up to 80 percent number removal efficiency. Power consumption was generally low, about 20 to 30 watts, to achieve these levels of performance.

Jan 1, 2009

By K Ehrig, J Griffith

An extensive suite of elements are routinely assayed on all resource drill core samples to assist in deposit scale resource definition, local mine scale delineation of ore zones, and ore characterisation for the planning and scheduling of mining and processing of ores at Olympic Dam. This paper discusses a deposit scale geochemical relation that can be used by mine geologists to find more high-grade ore at the local mine area scale at Olympic Dam.A 3D grade shell representing 0.8 per cent Cu was created for a mine area using drill hole assay data. This defined the geometry of the ore zone. The Cu-grade shell was then overlain onto the existing resource block model to evaluate the relationships between the Cu-grade shell, copper and other elements. The strongest correlation was between copper and manganese. The block model showed a dramatic decrease in the concentration of manganese just below the below the Cu-grade shell.Several drill holes that intersected the Cu-grade shell were selected to evaluate the copper manganese relation at the drill hole scale. As expected, the individual drill holes displayed a strong inverse relation between copper and manganese. A geochemical footwall was then modelled representing 0.1 wt per cent Mn. Using both the Cu– and Mn-grade shells, several drill holes were designed/drilled and all hit high-grade copper.For the vast majority of the deposit the inverse relation between copper and manganese is valid; however, in areas with intense chlorite alteration (related to amounts of mafic to ultramafic rocks) this relation is not as strong, due to increased manganese in the rock mass. Even though using the copper manganese relation as a drill targeting method was not always as reliable in a few small areas of the deposit, it demonstrates the value of using existing assay data integrated with the resource block model to discover local mine scale geochemical relationships which can be used to more effectively design drill holes to discover high-grade ore at Olympic Dam.CITATION:Griffith, J and Ehrig, K, 2017. Using existing data to improve the delineation of ore at the Olympic Dam Fe-oxide Cu-U-Au-Ag deposit, in Proceedings Tenth International Mining Geology Conference 2017, pp 321–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Dean Nichols, Matt Ortel

Explosive accidents in the United States have brought increased attention to emergency operation plans (EOP) at all facilities that manufacture, transport, or store hazardous materials – particularly explosive materials. Explosions are sudden, powerful, and complex events that are difficult to characterize in terms of the thermal, over pressure, and debris effects. Industry, regulatory, and public officials require emergency response planners to not only anticipate the blast effects of an explosion, but also to prepare an appropriate response.

Jan 1, 2016

By J. Kern, T. F. Torries

Identifying high value areas of unmined coal when large quantities of coal are available relative to annual markets is difficult because of the uncertainty of when the coal is to be mined. A GIS based methodology developed to value reserve coal in a producing coal region for the purpose of ad valorem taxation also identifies high value areas for mining investment. The methodology is unique in that it accounts for most mining, environmental, and market factors to determine when specific properties are to be mined. The methodology and data base are useful for directing regional exploration and acquisition activities toward most favorable areas.

Jan 1, 1999

By T. Faulkner, S. A. Richards

"The Scale-Distance formula is one of the primary means of determining the maximum amount of explosives that can be safely detonated at one time by a single delay. This paper describes a method of applying the Scale-Distance formula to the entire mining area using gridded surfaces. Using this technique, the operator can better determine the economic impact of nearby structures on the mine plan. INTRODUCTION As the surface mining of coal and stone encroaches near populated areas, precautions must be taken to minimize blast vibration damage to protected structures. The common method employed to minimize vibration damage is not to reduce the total amount of explosive in the hole (which would negatively affect fragmentation), but rather to introduce delays to reduce the amount of explosive detonated at any point in time. The Scale-Distance formula, an industry-accepted standard, may be used to calculate the maximum weight of explosive that can be detonated at one time without damaging the structure. This information may then be used to determine the number of delays required for each hole. Detonators make up a large part of the cost of blasting. At roughly $15 per detonator an additional detonator in the hole can be significant. It is normal to set off hundreds of holes at in one shot. An additional detonator in each hole can cost additional thousands of dollars per shot. The number of detonators is also a function of the depth of the holes and the hole spacing. Being able to accurately forecast the economic impact of blasting near structures improves a company’s ability to make informed decisions on how to approach property owners. Operators basically have three options when dealing with property owners: 1. Buy the property and blast without restriction 2. Negotiate with property owner for a waiver to allow unrestricted blasting 3. Comply with the legal blasting restrictions This paper proposes a method for the engineer to forecast for all points in the proposed mining area the impact of nearby structures upon the blast design. Being able to create a contour map and ultimately estimate the number of delays required for the entire forecasted mining area, the engineer can create accurate economic forecasts of the cost of blasting. The objective is to reduce the level of uncertainty in the forecast of the blast component portion of the forecast."

Jan 1, 2016

By G. M. Molinda

Ground Penetrating Radar (GPR) is being investigated for the potential to determine roof hazards in underground mines. GPR surveys were conducted at four field sites with accompanying ground truth in order to determine the value of GPR for roof hazard detection. The resolution of the current system allows detection of gross roof fractures (>63 cm (s1/4 in) zone) or rider beds in coal measure roof. Data quality is not yet sufficient to detect small bed separations or subtle lithologic changes in the roof. Differences in data quality are discussed, as well as suggestions for collecting improved data.

Jan 1, 1996

By M. Grodner

Ground Penetrating Radar (GPR) is an electromagnetic geophysical reflection technique that maps reflections associated with a change in electric properties of the target medium. It can thus be used to map the geometry of geological features and fractures as these can have different electromagnetic properties to intact rock. GPR was used successfully to determine the position and nature of the fractures in the tunnel sidewall, in the area of the simulated rockburst experiment. By comparing the radar scans acquired before with those acquired after the blast, it was possible to determine which fractures were reactivated by the blast and where new fractures were developed. It was found that the mining-induced fractures that formed during the development of the tunnel were re-activated by the simulated rockburst, as indicated by their increased reflectance on the radar scans. In addition, several new tunnel sidewall parallel fractures developed in the area of the blastholes. GPR thus clearly shows how and where the fracture pattern changed as a result of the blast and contributed to the understanding of the mechanisms of damage associated with the blast, and perhaps rockbursts in general.

Jan 1, 2001

Well designed and maintained haul roads are the key to minimising truck haulage on-road hazards and costs, as well as increasing productivity. However, practically designing and managing a haul road for optimal performance is often diff cult to achieve. Poorly designed and built roads exhibit high rolling resistance - a one per cent increase in road rolling resistance can typically reduce speed on ramp by as much as ten per cent - and on the f at by up to 26 per cent. In the current economic climates, investment and operating decisions come under scrutiny. In the long run, this scrutiny returns improved efficiencies and leaner, healthier operations. The focus of this evolving evaluation process should and will certainly fall on haulage operations - simply by virtue of their contribution to overall cost of operations - often in excess of 50 per cent of total costs for deep open-pit mines. Whilst the end result - improved efficiency and reduced cost per ton hauled - is not in itself problematic, it is the route, or process followed to achieve these savings that needs to be carefully managed. We can be guided on this journey by our understanding of how a road is designed, and, critically, the interplay between a good design and safe, cost efficient haulage.This paper brief y summarises the evolution of mine haul road design, from the seminal USBM work of Kaufman and Ault in 1977, through to current geometric, structural, functional and maintenance management design components. These augmented design and management guidelines have been developed over the past decade, both in response to the requirements of mine operators for more safe and efficient haulage systems, and the truck manufacturers' requirements for a more predictable and controlled operating environment. These developments have been paralleled by the need to minimise haulage hazards, both from a health and safety perspective. Generally, both objectives have been achieved, but with some specific areas of design and operation still presenting ongoing potential health and safety hazards.The paper then summarises current design guidelines for these safety-critical issues, both from a road-design 'best-practice' and road management perspectives. Implementation of the approach is seen as a basis for reducing the potential of an under-designed mine road to lead to health and safety defects and secondly as a means of giving haul road safety and performance issues greater prominence in the minds of the road-user, operator, mine planner and designer alike.

Dec 6, 2010