Search Documents

Minerals and Metals Group (MMG) Century mine (Century) is a large open-cut mine in northwest Queensland approximately 2.5 km long, 1.5 km wide and 240 m deep, with an ultimate pit depth of 320 m. In 2009, the mine experienced three failures which began as small failures, and progressively developed into significant multi-batter failures. The incidents were managed by a combination of analysis, redesign and practical management to achieve positive outcomes for the mine. On the south wall of the mine, a series of batter-scale wedge failures occurred in December 2007. Analysis of structure orientations and design changes aimed to minimise the risk of failure extending over multiple batters, while accepting a risk of further small-scale failures. Design changes were constrained by a culturally sensitive area (CSA) located south of the wall. As mining progressed, shallow wedge failures developed over multiple batters and cracks were observed 60m back from the pit crest, indicating that a large-scale wedge failure was developing. Movement increased in January 2009 as a result of significant rainfall. After considering several design options, the area was stabilised by a cut-back of the wall. Two multi-batter failures also occurred on the north wall as mining progressed through a structurally complex area. Both north wall failures began as small failures that progressively developed, and required a redesign of the wall below as well as practical management of safety aspects. The complex structural geology was difficult to predict ahead of mining, and required geotechnical input into design changes as mining progressed. All three failures potentially had significant impact for ore recovery, and were managed by a combination of analysis, redesign and operational management have resulted to achieve positive outcomes in a challenging mining environment.

May 1, 2010

By Carol J. Odell

As a mining social practitioner, social indicators are within the purview of required competencies. A situation, where the ER manager requested assistance in quickly deriving a few social indicators for the strategic plan motivates this paper: despite ample technical knowledge about indicators, a clear understanding of stakeholder aspirations and concerns, as well as familiarity with management priorities such a request required reflection to produce a satisfactory approach, which combined pragmatism with enough academic rigour to provide reliable measures, while being justifiable to management who are unfamiliar with many of the pertinent debates. Importance: Social indicators enable the identification of more and less effective mine-community engagement strategies as well as providing primary data to better understand how the mine-community social system responds to different interventions, thus guiding future engagement plans. In addition social indicators: ? Assist communication about social strategies with Engineering and Operations management, using a quantitative language that is familiar to them. ? Provides concrete data to engage stakeholders to discuss progress and challenges arising, to move discussions towards technically robust strategies and away from politically interested proposals. ? Finally, social measurement is required more and more in due diligence, covenants and ongoing monitoring in Independent Engineering assessments of projects for financing. This paper begins by considering some technical considerations that are useful to guide indicator development. It then introduces the field research informing this paper and discusses some useful results in the light of further applicable concepts from the literature. The paper ends by considering corporate aims in applying corporate social responsibility (CSR) programs and discusses the application of the research for practitioners at mining operations, in the light of these aims.

May 1, 2010

The prime objective of geometallurgy is to improve the profitability of mines through the use of spatial models of rock properties that have a significant impact on value. Although a key property is the grade of the component of interest, because it directly influences the revenue from saleable material, increasingly attention is being focused on other attributes. These 'non-grade' variables may have a less direct, but equally profound impact on value, either by reducing potential revenue (eg lowering recovery, deleterious elements, etc) or increasing mining or treatment costs (eg comminution, grindability, throughput, reagent use, etc). Collectively, these variables have been described as 'geometallurgical'. There are three main areas of activity required to realise the value of geometallurgy: 1. acquisition of appropriate data through sampling and measurement, 2. building spatial models of geometallurgical variables, and 3. using these models to optimise value. Each of these is built on the foundation of the preceding step. In building reliable spatial models, it is critical that the amount of error introduced to data by the sampling and measurement processes is understood and quantified, in order that the inherent variability of the component of interest can also be properly understood. Management of the quality of grade variables is now applied (with different levels of diligence and success) across nearly all sectors of the mining industry, not least because of the necessity to adhere to Codes of practice (eg JORC, 2004). The necessity for quality management and at least the broad framework of what to do in practice is reasonably understood by many relevant professionals. There are also a number of tools, including software products, statistical analyses and presentation formats, available for those managing grade data. It is also abundantly clear, that in many cases people have little understanding of why they are doing particular quality control activities, or how to sensibly interpret the results. The same is not true for many geometallurgical variables. In almost all instances the authors have seen, the magnitude of sampling and analytical/measurement error variance embedded in geometallurgical test data is untested and unknown. This is partly because until relatively recently, metallurgical data has mainly been collected for the purpose of process and mill design, with few, expensive tests carried out on 'average' samples of the orebody. Increasingly however, there is a move towards collection of much larger data sets from spatially distributed sampling, and thus a growing necessity to understand the errors inherent in both sampling and analysis of these types of variables, and how to manage them. In order to understand how the quality management practices applied to grade variables can be extended to geometallurgical variables, it is essential to understand the theoretical foundation that supports these practices. This requires an analysis of the concepts that underpin the 'principles of additivity' (Matheron, 1963), the 'theory of sampling' (Gy, 1982, Pitard, 1993), and 'statistical process control' (Shewhart, 1930). Relevant concepts are then integrated to form a foundation to develop methods to improve the quality management of geometallurgical variables. Application of this framework will significantly increase the integrity of geometallurgical data, the reliability of geometallurgical models and ultimately the value derived from implementing geometallurgy. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Mar 1, 2010

The Canadian mining industry is one of the strongest in the world. Not only does the country produce a sizable amount of minerals and metals, Canada plays host to hundreds of global mining companies, large and small. The country, for the most part, recognizes the importance of natural resource development, particularly mining, to its economic well being. Like any country, though, there are federal and provincial regulations on the books that the industry takes issue with. But there are also certain economic incentive programs in place to encourage exploration and mine investment. And, unlike the industry and the United States government, the Canadian government and mining industry appear to have a reasonable working relationship.

Jan 4, 2010

By J. Harrison Daniel

Were the legislators and politicians responsible for the closing of the U.S. Department of the Interior?s Bureau of Mines (Bureau) in March 1996 fully aware of what they were doing? Throughout the United States? history, the domestic mining and minerals industry has been largely responsible for the nation?s growth and prosperity that had made it a world leader. The mining and minerals industry made it possible for the young nation to catch up with Europe during the Industrial Revolution, played an essential role leading to victories in World Wars I and II and was a core ingredient for continued economic growth. For a number of decades, America?s import dependency on non-fuel mineral materials has continued to increase. (USGS Mineral Commodity Summaries). Developing domestic resources to meet current and future demands ? particularly those resources considered to be of strategic and critical value to national security ? is necessary. Federal involvement is required since many of these resources are located on public lands. Another reason for federal involvement is that the success of the industry depends on long-range research programs and advances that may take up to 25 years to become commercially available. This situation requires federal partnership to coordinate the programs necessary to collectively involve the industry, individual mining companies and colleges and universities. So, how was it possible to close a federal agency that had contributed so much to the nation?s welfare in a mandated 90-day period, with more than 1,200 employees losing their jobs?

Jan 4, 2010

By J. P. Ducarme

Numerous fatal/nonfatal accidents involving underground workers struck by powered machinery occur yearly, with continuous miners and roof bolters involved in the majority of these accidents. In an attempt to reduce these accidents, researchers at the the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory conducted studies of operator interactions with the motions of continuous mining machines and roof bolter boom arms. These operators generally perform their tasks in close proximity to the equipment in confined workspaces, often employing awkward postures. Since experiments with human subjects using the actual equipment were not feasible due to safety concerns, researchers opted to conduct controlled experiments in laboratory settings. Utilizing motion capture technologies and computer simulations, the studies collected data on equipment and operator movement in a range of seam heights and working postures. This article details the results of these studies to examine operating speeds based on usage and seam height.

Jan 3, 2010

By Baha Abulnaga

Slurry pipelines are used in a number of countries to convey processed ore mixed with water over long distances from remote mine sites to ports or plants for further processing. In Egypt and Sudan, numerous mineral resources are scattered in remote areas. Through the years, Egyptian geologists have identified 268 sites for metallic ores and 386 sites for industrial nonmetallic minerals. A large portion of these sites are in the Eastern Desert in an area called the Nubian Shield. Similar sites are found in the Sudan where mining contributes to less than 1 percent of the gross domestic product (GDP). There are three important components of infrastructure needed to develop these resources ? power, water and transportation. While Egypt is able to satisfy 70 percent of its needs in iron ore from the Gadideh Mine in the Western Desert, it needs to expand its other resources to reduce imports heavily sedimented. Dredging of these sediments and transporting them by slurry pipelines would enhance an industry of bricks or agricultural development based on tailings technology often used in mining. This article explores the potential for slurry technology for opening new mines in the desert or recuperating the sediments of the Nile. The technology by itself would be new to both countries and would benefit from collaboration, particularly to de-silt the Nasser-Nubia Lake.

Jan 3, 2010

By Scott Ellenbecker

Soon New York City will have a new train station. A tunnel project is under construction to extend Line 7 to a new station that is located near the Jacob K. Javits Con-vention Center. This is also part of the Hudson Yards redevelopment project that is intended to aid redevelop-ment of the west side of Midtown Manhattan around the Long Island Railroad?s Caemmerer Railyard. The station, or ?cavern? as it?s called by those excavating it, will be the portal for that growth. In the city, public transportation means high-rise residential proper-ties will have better access to the business district, and those outside the area will have greater access to event facilities ? two factors that are critical for development investment.

Jan 3, 2010

By Ellsworth R. Spencer

An assessment of U.S. western hardrock miners? noise exposures was conducted as part of a multi-year National Institute for Occupational Safety and Health (NIOSH) survey of noise exposures in each sector of the mining industry. Noise from selected mining equipment and operator noise exposures were measured, analyzed and tabulated for dissemination to the participating sites and are being used to direct NIOSH research and interventions to address the greatest noise hazards. Eighty-two noise dosimeter measurements were obtained, along with time-motion studies as the miners operated hardrock mining machines. Of the operators, 96% had daily noise doses that exceeded the U.S. Mine Safety and Health Administration?s (MSHA) permissible exposure level. The average gold miner dosages while operating the following equipment were: haul trucks - 261%, load-haul-dumps (LHDs) - 235%, single boom drills - 221%, bolters - 214% and dual boom drills - 163%. The worst exposure level was a silver miner with a daily dose of 873%. Time-motion data showed that this miner?s exposure accumulated most rapidly while operating a jackleg drill. These results will be used to help prioritize noise control development by NIOSH and other partners.

Jan 3, 2010

By William H. Langer

The annual consumption of sand and gravel aggregate in 2006 in the Phoenix, AZ metropolitan area was about 76 Mt (84 million st) (USGS, 2009), or about 18 t (20 st) per capita. Quaternary alluvial deposits in the modern stream channel of the Agua Fria River west of Phoenix are mined and processed to provide some of this aggregate to the greater Phoenix area. The Agua Fria drainage basin (Fig. 1) is characterized by rugged mountains with high elevations and steep stream gradients in the north, and by broad alluvial filled basins separated by elongated fault-block mountain ranges in the south. The Agua Fria River, the basin?s main drainage, flows south from Prescott, AZ and west of Phoenix to the Gila River. The Waddel Dam impounds Lake Pleasant and greatly limits the flow of the Agua Fria River south of the lake. The southern portion of the watershed, south of Lake Pleasant, opens out into a broad valley where the river flows through urban and agricultural lands to its confluence with the Gila River, a tributary of the Colorado River.

Jan 2, 2010

By Douglas E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH?s Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance, which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items that require the constant attention of miners operating in these conditions.

Jan 2, 2010

By Antonio Nieto

According to the analysis of surface powered haulage accidents involving off-highway haul trucks in openpit mining, the U.S. Mine Safety and Health Administration (MSHA), reported 1,300 fatal accidents from 1990 to 2005. Of these, 163 were considered off-highway truck haulage accidents, and at least 23 involved collisions of an off-highway truck with a neighboring vehicle or a worker on foot (Nieto and Dagdelen, 2006). In general, an average of 18 nonfatal accidents and three fatal accidents occurred in openpit mining per year when equipment backed over the edge of an embankment, stockpile or dump point (Fessak, et al., 2003). The specific problems that need to be solved can be determined by carefully studying the accidents involving haulage trucks (Marrara, et al., 2004). Solutions to haulage truck safety must consider the human factors affecting each task even when engineering solutions seem most appropriate. In surface haulage, human performance becomes a critical issue because of the unusual demand the vehicle?s places on their human operators: ? Roadways and working areas change frequently in mining operations. ? The sheer mass of mining equipment such as trucks requires control inputs (e.g., braking) far in advance of the desired action. ? Rough roads, loading and unloading impacts can subject the driver to dangerous shocks and vibration. ? Visibility is sharply curtailed by the bulk of the vehicle generating large blind spots. All of the above issues can be attributed partially to the lack of visibility (Pyles et al., 2003). Driver visibility and communications are key issues to reduce mining truck accidents. Analysis of fatalities and injuries involving mining equipment demonstrates the need to develop new intervention and control strategies to mitigate the risks associated with mining equipment operation. Ongoing development of these and other new strategies is required to achieve a reduction of injury in the mining industry

Jan 2, 2010

Collaboration between education providers is the key to long-term sustainability and improved quality in mining education. The mining industry is now, more than ever, an industry doing business on a global basis. Staff are recruited by global mining companies in many different countries and can find themselves deployed anywhere in the world. The mining engineer of tomorrow must be willing to take on this international challenge, and must be educated to a level where he or she has a comprehensive grounding in technical aspects of mining engineering, but also a well-founded appreciation of management, social, environmental and cultural issues that may be encountered around the world. In order to deliver such an education, academic providers must collaborate at both a national and international level. This paper provides an overview of progress that has been made in Australia through the national joint venture ? Min¬ing Education Australia (MEA). Supported by the mining industry in Australia, through the Minerals Council of Australia (MCA), MEA has been operational since 2007 and is seeing the development of a range of innovative courses and delivery methods, together with a high level of staff cooperation across the country. MEA has also commenced some international teaching initiatives that are seen as a catalyst for a far greater degree of international collaboration in the future. Such activity is not only to the benefit of the students who are taught by experts from around the world, but it also ensures that individual univer¬sity programs remain viable in terms of staffing numbers and financial performance. The paper also presents some statistics on recent upward trends in mining engineering student numbers from around the world, in response to the global shortage of mining engineers.

Jan 2, 2010

By C. Y. Liu

This paper principally deals with the application of caisson foundation in the Chinese bridge building industry, the different types of caisson foundation adopted, and their spheres of application. Caisson foundation has been used and speedily developed for bridge works in New China, and a number of new innovations have been made in its design. Especially in deep water foundation, the Nanjing Bridge over Changjiang has attained one of the deepest bridge foundations in the world. There are six types of deep caisson foundation being now in use in China, namely:

Jan 1, 2010

By M. Dondelinger

This paper presents a comprehensive review of steel sheet piling including internationally manufactured hot rolled sections, their history, applications, installation and driving techniques. The discussion will cover both temporary and permanent installations; temporary piling used in construction of cofferdams with various bracing systems, deep foundation installations for buildings, bridges and tunnels, etc., and permanent piling used for highway, railroad and bridge construction as well as for riverbanks, piers, wharfs and docks, normally required for port facilities. In addition, cofferdams, as self-supporting gravity structures where interlock strength is of prime importance, will be discussed. The design and application of light, intermediate and heavy sections will be presented including heavy combined walls and information on Z-shaped, U-shaped and HZ sections and their corresponding interlocks. Emphasis is placed on new developments for design applications for deep foundations and waterfront structures within the "state of the art".

Jan 1, 2010

By Vincent Jue

In December 2009, the Italian High Speed Rail Network AV began running over the full 1000 km system length from Turin, at the foothills of the Alps to Salerno, on the seacoast south of the volcano Mt. Vesuvius. It runs through Alpine rivers, highly seismic active zones, mountains, river plains, and through some of the most densely populated areas in Europe as well as some of its most expensive real estate. The Italian High Speed Network?s technical/economic constraints and its regulatory/socio-environmental concerns well may mirror similar obstacles set to confront the nascent California High Speed Rail Program. The two types of constraints must be dealt with together to reach the best construction solution. It is estimated that more than 20% of Italian High Speed Rail Network costs were spent on ground engineering including over 150 km of tunnels, 200 km of viaducts and bridges and 650 km of embankments and trenches. However, it also is estimated that 25% of costs were spent on social and environmental integration of the new rail lines including over 6 square miles of green offsets, 160 km of anti-noise walls, and 300 agreements for socio-environmental work. This paper will look at four examples of innovative ground engineering solutions, each with its own intricate set of constraints: ? Foundation system for viaducts across the ?Po? and ?Ticino? rivers. ? Soil consolidation under railway embankments ? Requirement of short tunnels for physical and environmental reasons ? Construction of railway stations in a confined right of way

Jan 1, 2010

Geologists in some underground gold mines collect grab samples from broken ore piles or trucks as a method of grade control. It is often known as muck sampling. Generally, the goal of grab sampling is to try and reconcile the mined grade at the ore source to the predicted grade and/or predict the mill feed grade. The mass of the sample collected is limited by health and safety issues, as well as by the capacity of the laboratory to process the samples within a given time frame. In general terms, grab sampling is known to be problematic because samplers tend to oversample the fines, and/or pick out high-grade fragments; surface sampling of piles does not test material within the pile; muck piles in development drives/faces are likely to be zoned due to the blasting sequence; high or low-grade material may preferentially segregate in the pile during mucking; the five per cent mass reject size of the material in muck piles is very large from underground blasting; some correlation usually exists whereby the larger fragments are enriched or depleted in the critical component of value; and the average error made in estimating the true stockpile grade is likely to be high. The method is prone to chronic fundamental sampling, grouping and segregation, delimitation, and extraction errors. Substantial warnings must be given about the use of grab sampling for grade control in gold mines. The method may appear to work sometimes, which can be attributed to a fine gold particle sizing and more disseminated distribution. As with all sampling methods, its appropriateness must be determined by ore characterization and heterogeneity testing to ensure the method suits the ore type.

Jan 1, 2010

By Jilai Xue

Oxygen gas bubbles generate on anode during Pb electro-deposition process in PbSiF6-H2SiF6 aqueous solutions at room temperature. Cell voltage varies as the bubbles formed on the anodes surface. The bubble layer on the anode makes a voltage drop that consumes energy in the Pb process, which can be reduced by applying ultrasound on the anode. The effects of ultrasound frequency and anodic current density were investigated with ultrasound on and off, alternatively during the Pb electrode-position process. The removing of the gas bubbles were recorded in association with a drop in the cell voltage. The cell voltage can be lowered by 4% - 6% with ultrasound, which has potential for energy saving in Pb production.

Jan 1, 2010

By C. -J. Rick

By implementing a converter downstream of the reduction furnace it is possible to broaden the product range significantly. The converter can also successfully be used to strip furnace slag from chromium oxide. Some process alternatives and their economical, practical and environmental implications are studied using process models developed based on UHT?s long experience in stainless steelmaking, stainless steel process control and charge chrome refining. Keywords Charge chrome, converter refining, ferrochromium products, process design.

Jan 1, 2010

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock formed by the consolidation of clay, mud and (or) silt. Government and legislative programs The U.S. Environmental Protection Agency (EPA) invited industry to nominate representatives to a review panel that will help the EPA develop rules to regulate air toxics from the production of brick and structural clay products. The EPA was required to establish a review panel because these regulations will significantly affect small businesses. The regulation of air toxics falls under the Clean Air Act.

Jan 1, 2010