Search Documents

By F. D. Ayhan

The aim of this study was to investigate the effects of various water mediums on desulfurization and deashing of a coal sample using flotation. For this purpose, experimental studies were conducted on a coal sample containing high ash and sulfur contents. The effects of pH, solid concentration, collector amount and frother amount on the flotation were investigated separately in Mediterranean Sea water, Çermik thermal spring water, snow water and tap water. Flotation results indicated that, when comparing the various water mediums, the following order for the ash content was obtained: snow water < Çermik thermal spring water < tap water < the Mediterranean Sea water. For the reduction of total sulfur, the following order was obtained: snow water > Çermik thermal spring water > Mediterranean Sea water > tap water. When snow water was used as a flotation medium, it was found that a concentrate containing 3.01% total sulfur and 27.64% ash with a total sulfur reduction of 57.06% was obtained from a feed containing 7.01% total sulfur and 41.17% ash.

Jan 1, 2009

By Yi Luo

Subsidence events occurred over inactive room and pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidences to identify the causes are often lacking. In order to conduct a thorough and impartial investigation, good knowledge in subsidence theories and other ground control subjects and broad experience are required.

Jan 1, 2009

By M. Verri

[ ]

Jan 1, 2009

Construction of the Boddington Mine 130 km (81 miles) southeast of Perth, is about 89 percent complete. When the $2.9-billion development is finished, it will be the largest gold mine in Australia, producing 31 t/a (1 million oz/year), according to project majority owner Newmont Mining. Newmont?s acting regional group executive for Asia Pacific, Philip Stephenson, told a gold conference in Australia that the project would be ?the biggest thing for Newmont this year.? The project has been in the works for more than 10 years, but because of a three-sided ownership and fluctuating gold prices, it struggled to get started. However, Newmont is set to become the full owner of the project and is moving ahead on the low-grade project. ?We are targeting annual production of 31 t/a (1 million oz/year) for each of Boddington?s first five years. When it is in full production, Boddington will be the largest gold mine in Australia,? Stephenson said. ?The mine?s costs applicable to sales will be around US$9.64/g (US$300/oz) and that puts Boddington into the bottom quartile of the global cost curve. ?Strategically for Newmont, Boddington coming on-line will improve Newmont?s overall global geopolitical risk profile as it delivers greater exposure to an AAA-rated country.? Boddington has a projected mine life of 20 plus years. It has current total reserves of 622 t (20 million oz) and rising. Stephenson said Boddington has the largest reserve base of all gold projects in production or those that are about to go into production in A-rated countries or better. And it will be an important asset for many years to come. Newmont will acquire the remaining 33 percent share held by AngloGold Ashanti in a deal that should be concluded in the next two months. Australian miner Newcrest Mining Ltd. had exited the joint venture several years ago. Newmont had come into the project through the take-over of then Australia?s leading gold miner Normandy Mining, while AngloGold Ashanti gained entry through

Jan 1, 2009

By V. Svalbonas

Everybody has an opinion what the quality of a grinding mill head casting should be, yet extremely few take the time, or get the opportunity, to compare their opinions against fitness-for-purpose data. The real question is not how flawless the casting should/could be, but rather how long will ?this? casting survive in operation. To validate an opinion on this topic one needs either extensive historical data, or comprehensive experimental data, or preferably, a combination of both. The same data can also be used to establish the conservativeness, or lack thereof, of analytical prediction methods.

Jan 1, 2009

By Robert H. Peters

This report presents a literature review conducted by the U.S. Bureau of Mines. The review summarizes what has been learned from recent empirical studies of the relationship between mine safety and characteristics of miners, mine management, and mining companies. The review is based on literature published in the United States during the period from 1976 to 1988. In addition to summarizing the empirical findings, this report discusses the implications and limitations of these studies, and gives recommendations for improving mine safety. An annotated bibliography section appears in the appendix.

Jan 1, 2009

By M. S. Raseroka

An experimental rig has been constructed to produce chloride stress corrosion cracks in Type 304L stainless steel tube samples. The samples are to be used to test possible in situ repair methods in future work. The factor which influences the time to failure most strongly is the sample temperature; the distribution of cracks within the sample is affected by local temperature variations and by the position of the water line. Low-frequency oscillations in stress, caused by the on-off temperature controller, did not appear to influence cracking in these tests.

Jan 1, 2009

By I. Alp

Application of magnetic separation was investigated for the enrichment of colemanite ores by removing the magnetic gangue fraction. The detailed XRD analysis of the ore has indicated that the gangue fraction is composed predominantly of the iron-bearing silicates such as smectite and, to a lesser extent, illite. Magnetic susceptibility measurements of the colemanite and gangue samples have proved that colemanite is diamagnetic in character whereas gangue fraction is weakly paramagnetic to allow the removal of this fraction by magnetic separation. Magnetic separation of the crushed and sized ore samples (-5 mm +75 µm) was performed using a high intensity permanent magnetic separator. Under the test conditions a colemanite concentrate (41.29 wt.% B2O3) was found to be produced from the crushed ore (30.76 wt.% B2O3) at a recovery of 96.76%. These findings suggest that magnetic separation has great potential as an alternative process for the production of a concentrate of commercially sufficient grade.

Jan 1, 2009

By Ramón Alanís, Filiberto Orrante, Andrea Festa, Baldomero Gutiérrez, Fernando Cornejo

"SGS implemented two rules-based fuzzy logic expert applications on two grinding circuits operated by Peñoles Group in Mexico. Both expert systems are based on control strategies that push against process constraints to improve throughput. Based on proven methodologies, the projects also required some new approaches that led to permanent changes to the mill control strategy.This paper provides descriptions of the implementation, operation and performance of both expert systems. It also reviews how improved production rates were achieved through the use of a common set of expert technology tools. An overview of the resulting control strategies implemented on the two circuits is presented. The paper also discusses the identification of the process constraints within each circuit and how these constraints are used within the expert systems.INTRODUCTIONMexico-based mining company Peñoles Group and the Advanced Systems group at SGS, formally known as MinnovEX Technologies Inc., collaborated on the implementation of two expert systems in two grinding plants, both located in Northern Mexico.The primary objective of the expert systems was to increase throughput whilst still maintaining the cyclone overflow product size within an acceptable range. The secondary objective was to achieve a high level of utilisation of the expert technology.In order to achieve these objectives, SGS proposed a proven methodology which leveraged the existing operating and technical expertise at site through the client’s involvement in the design and implementation stages. The in-house operating and technical expertise of SGS was also brought to the project and implemented with the client’s approval at all stages. At both sites the final acceptance was defined upon meeting both process and utilization parameters.The development and deployment of rules-based fuzzy logic applications has matured as a technology and consequently, clear definition of process states and their place in the logic structure to control a given circuit are now transferable. The key to the robustness of the control logic depends on selection and tuning rules for maintaining stability and optimizing a given circuit. Application integrators need to have a standardized approach for timely integration and deployment; a critical component to avoid the common critiques that expert applications are idiosyncratic and difficult to maintain."

Jan 1, 2009

By Russell Barr

Operational excellence is generally known as a management system integrated across critical functions that is geared towards continually improving operational performance. Functional areas such as health, environment and safety, quality and human resources are the focus of many corporate-wide operational excellence programs. Operational excellence also focuses on improving areas such as customer orientation, employee empowerment as well as process, and systems optimization. It is widely viewed as critical to sustaining business performance improvement. Although it is difficult to find a universally accepted definition, or even common foundation in many respects, operational excellence remains a popular term in the business world. Many organizations have developed their own version of organization excellence, influenced by such individual factors, other similar institutions or even third-party service providers. A mining organization is no different from other organizations in that adopting and implementing effective operational excellence programs can dramatically improve business execution and performance across regional or global interests. This paper brings together various perspectives of operational excellence and reconciles them for a useful composite for the mining industry. While most agree that operational excellence should include normal functions in a manufacturing operation such as production, maintenance and engineering and processes such as quality, environmental and continuous improvement, many other factors for operational excellence seem to vary from perspective to perspective. Thus, programs that manufacturers engage in may seem the same, but may, in fact, be different in key areas. This may affect organizational performance in tangible ways. Management must buy into the company?s definition of operational excellence and be dedicated to achieving it. A review of many of the existing definitions of operational excellence, explicit or embedded as part of a program, seems to yield the following common factors: ? It should help organizations better execute their processes and services. ? It should be geared towards improving quality ? It requires that the various operations should be aligned with the overall enterprise strategy. ? It should be geared towards continuous improvement. A composite of operational excellence definitions suggest that it is: ? Geared towards helping the organization achieve sustained profitability; ? tied to strategic alignment and business objectives; ? tied to solid investment strategies; ? integrated as part of the culture, process, time plan and performance; ? a relevant performance measurement system; ? extended to include all aspects of the supply chain (including external suppliers); ? integrated with health, safety and environmental (HSE) aspects. And, while the pursuit of operational excellence intuitively suggests that businesses should improve, it is very difficult to achieve given the difficult challenges facing companies today. Mining businesses face numerous pressures to perform in a global marketplace such as demand, energy cost, variable cost and pricing fluctuations as well as infrastructure challenges to further confound the environment. Companies generally must look to the following:

Jan 1, 2009

"Drilling twinned holes is a traditional technique used for verification of intersections of high-grade mineralization, testing of historic data, or confirmation of drillhole data during geological due diligence studies. Twinned holes can also be used for special tasks such as correcting earlier data that are recognized to be biased. Successful implementation of the twinned-holes technique requires thorough planning. Experience suggests that good practice is to drill twinned holes no more than 5 m apart. Many unsuccessful twinned-holes programs could possibly have failed because the twinned holes have been drilled too far apart.Twinned holes are best compared by mineralization intersections and, if the data and geological characteristics of the deposit permit, by samples, equal-length composites, or geological units. Variables to be verified by twinned holes should include the thicknesses of the geological units of interest (e.g., mineralized thickness) as well as the presence of significant geological features (e.g., ore/mineralization contacts, alteration, etc.).A formal, rigorous analysis of twinned-hole data is essential. Repeatability of sampling, analytical results, and bias must be analyzed and statistically quantified. The number of twinned holes required for conclusive statistical and geostatistical analysis can be as high as 20-30, in particular where the studied variables are characterized by high short-range (local) variability.The efficiency of this approach is demonstrated by several examples of successfully applied twinned-hole projects, including applications to orogenic gold, mineral sands, bauxite, and iron ore deposits."

Jan 1, 2009

By Syd S. Peng

University research in the U.S. consists of three components; faculty, funding, and graduate students or postdoctorals. Individual faculty is the unit area of research that is not limited, although faculty normally performs research in their areas of expertise. Faculty can and often do join with other faculty in multidisciplinary research. Faculty research achievements or reputation reflects the standing of the program and university. Therefore, research is highly encouraged and regarded within the university community. Graduate students are the work force of faculty research and doctoral students are preferred for high-quality products. The federal government provides the majority of funding sources, with the remainder coming from industry, state government and others. Compared with other engineering majors, the mining engineering programs in the U.S. are unique in that they: ? Are small in terms of the number of programs, and number of faculty and students in each program. ? Serve a single industry (i.e., mining) and are thus cyclic, reflecting the up and down economic state of the mineral industries. Enrollment statistics during the past 70 years show that a cycle consists of approximately 30 years with the first 10 years up, followed by 20 years down. ? Have curriculum designed to emphasize and thus serve for either the coal, hardrock or industrial minerals industries. These unique features make mining engineering programs hard to manage in university environments. Funding for mining research has relied primarily on the federal government, i.e., the former U.S. Bureau of Mines (USBM) and currently the National Institute for Occupational Safety and Health (NIOSH). The mining industry does not directly perform, nor sponsor research projects. Federal funding provides primarily in-house research. In the last four decades, federal extramural funding was only available when Congress appropriated extra funding in response to mine disasters. For instance, a string of coal mine explosions in the mid to late 1960s prompted Congress to enact the Coal Mine Health and Safety Act of 1969. It provided massive research funding from 1970 to 1983 covering all mining-related subject areas. From 1984 to 1995, federal extramural research funding was minimal, through two generic mineral technology research centers for selected mining engineering programs. In 1995, Congress closed the USBM and transferred the health and safety of miners program to NIOSH. Federally-funded extra-mural research practically stopped from 1995 to 2006. In 2006 and 2007, in response to a series of disasters, including those at Sago, Aracoma, Darby and Crandall Canyon, Congress again appropriated funding for short-term re-search in selected subjected areas such as underground tracking and communication, mine seal and ventilation, and deep cover pillar extraction. Therefore, to develop a meaningful academic mining research program during the past three decades, funding needed to be drawn from other sources such as the mining industries. A ?meaningful? program requires a sufficient amount of consistent funding in order to produce effective results. A review of federally funded extramural research pro-grams shows that a great majority of contractors/grantees are private entities, involving few mining engineering faculty. This, in part, is due to the fact that mining engineering involves so many different subjects. Therefore, a small mining engineering program can only have resources to cover teaching in the core subject areas (i.e., extraction, ground control, ventilation and material handling), at best. In this respect, a successful and meaningful academic mining re-search effort requires strong supporting programs such as geology/geophysics, structural (applied) mechanics, material sciences, compute/software application, etc. Therefore, academic mining research had to rely on private sources such as coal companies, in the author?s case, for sustained funding in the past three decades. Relying on funding from coal companies presents several problems. The projects were small and considered routine consulting projects requiring practical answers in a very short time frame. This is not really suitable for academic research, for which the major goal of research is the training of graduate students. These short-term projects vary with time and mines, most of which are driven by U.S. Mine Safety and Health Administration (MSHA) or U.S. Office of Surface Mining (OSM) regulations. So sustained funding under such condition requires broad experience of coal mining operations, which is also not well-aligned for academic research where faculty tends to specialize in a narrow field. Consequently, under such a funding environment, it is important to keep in mind how to develop long-term academic research objectives from conducting small short-term consulting projects that require quick solutions. In other words, how to look beyond the quick answers and to develop broader and more fundamental theories applicable to other situations that advance the-state-of-the-art. In order to achieve this objective, faculty must act as the connecting link because graduate students come and go. Faculty must know the detail of each project such that they know what are the important unsolved problems, what to assign to specific graduate students and how to guide the next group of graduate students to continue the development and advance the mining science. Under such funding environments, the most effective way to conduct academic mining research and ensure quality products is to maintain a research group consisting of postdoctoral, PhD, and MS students of various rankings such that the senior ranks can assist in guiding the junior ranks, especially the senior PhD students who are experts in their dissertation research areas. A weekly meeting should be scheduled for the group in which problems encountered in the research are discussed or individuals take turns presenting the progress of their projects. During each meeting, the importance of open discussion on scientific issues must be emphasized. Thus, opinions are encouraged, debated, and rejected or accepted. Students are encouraged to listen to and analyze other points of view. In addition to training of this thought process, the meeting also helps identify the strengths and weakness of each individual. As the subject of research expands over time, the group?s and, thus, the faculty?s research experience broadens. With this approach, companies can get the quick answer they desire from expert research experience and the faculty can engage in meaningful applied and basic research that is most relevant to routine mine operations. The end result is that companies will have a high regard for academic mining research.

Jan 1, 2009

By J. R. Parga

In mineral processing, poor froth-flotation performance translates into both an enormous loss of revenue and an unnecessary waste of the ore reserve. In this context, Bacís Mining Company developed a versatile new, high-performance flotation-cell design that can be incorporated into various flotation circuits. The main feature of this circular cell is that it is comprised of two separate sections, namely, a flotation cell that uses wash water to minimize the entrainment of fine gangue particles into the froth product and an external bubble generator that produces small bubbles of relatively uniform size at a specified aeration-rate. The air/water mixture is blended with the pulp by gentle agitation, so as to enhance particle-bubble aggregate-stability. Comparative metallurgical performance with conventional flotation cells show that the power requirements and operating costs for precious metal flotation are three times lower, while the concentrate grade is 7% higher and the recoveries of precious metals are 5% higher.

Jan 1, 2009

By John G. Peacey, Leoncio Sevilla G., Ford. Kevan J. R., Erling Villalobos C.

"Kinross Gold Corporation’s Mantos de Oro (MDO) gold/silver mine in northern Chile currently processes 15,000 tpd of oxide ores through a mill, whole ore cyanide leach plant followed by a Merrill-Crowe refinery. With the expected depletion of these oxide ores in a few years a new sulphide mineral deposit, Ladera-Farellón has been identified to potentially replace existing ore reserves. The deposit contains approximately 0.5g/t Au, 6g/t Ag and 0.5% Cu. The principal sulphide mineral in the deposit is enargite (Cu3AsS4) which hosts the majority of gold and silver and the copper. Direct cyanidation testwork has shown the sulphide mineral is refractory with a low gold recovery of 36% and silver recovery of 45%. Oxidation of the sulphides is required to liberate gold and silver and allow recovery of copper as an important pay-metal. Therefore, at MDO a new metallurgical process route with oxidation as a pretreatment step is required for viable treatment of such new sulphide mineralized material with acceptable recoveries of pay-metals.Analysis of flowsheet options was completed based on bench-scale and pilot scale metallurgical testwork as well as with reference to existing studies and operations. The process options investigated assume concentration of sulphides by flotation, followed by either pressure oxidation, bacteriological oxidation or roasting. Preliminary evaluation of flowsheet options focused on process risk, operability, technology availability and the economics of the project with emphasis on use of the existing metallurgical plant to reduce capital cost. Operating costs for each process option were also included in the relative analysis.The challenges of treatment of MDO sulphides, principally enargite and pyrite for recovery of gold, silver and copper center on fixation of arsenic and sulphur capture with environmentally acceptable disposal of residue tailings. This environmental focus was included in the process option selection and comparative analysis.This paper presents a review of the process options considered and highlights comparative advantages/disadvantages of each process with associated environmental issues. Preliminary conclusions are drawn on roasting as a potentially favorable process option for the treatment of MDO sulphides."

Jan 1, 2009

By A R. Bye

Energy comes at great cost to our world and societies and therefore we should use it wisely and optimally. Societal pressure is enforcing this and the industry must respond by being proactive.The mine-to-mill approach to integrated mine and semi-autogenous grinding (SAG) mill optimisation demonstrated that throughput gains of up to 20 per cent could be obtained through a closer match of blasted run-of-mine ore to the feed best treated by a SAG mill. Since that approach was developed, new drivers have risen to prominence including environmental costs and impact of energy, water, waste. This is set against a backdrop of reducing ore grade and increasing demand that is pushing up our impact on the environment. The new challenges demand new approaches.This paper explores the opportunities in taking traditional approaches to optimisation to new levels of two-way integration and incorporating potentials for ore upgrade into circuit design. The new mantra may be æflexible circuitsÆ û designing and building for the present and the future by allowing for the uptake of new and future technology.

Jan 1, 2009

By A. Adu-Acheampong

The Mid-Tennessee Zinc (MTZ) mines, comprised of the Gordonsville, Elmwood, and Cumberland sites, last operated 4 years ago and are undergoing rehabilitation to begin production in 2008. The mines utilize a random room-and-pillar mining method that results in complex ventilation networks. Upon decommissioning, the mechanical ventilation units were removed and disposed of and several shafts sealed. In an effort to re-open the mines and operate in compliance with imminent Mine Safety Health and Administration (MSHA) diesel particulate matter (DPM) regulatory limits of 160TC µg/m3, a new ventilation system was required. The new ventilation system was developed primarily based on the diesel equipment required to meet production. Particular emphasis was placed on the DPM, diesel equipment utilization, main fan sizing, and fan locations to enable the mines to meet MSHA?s ventilation requirements in a cost efficient manner.

Jan 1, 2009

By F. F. Roberto

Many techniques that are used to characterize and monitor microbial populations associated with sulfide mineral bioleaching require the cultivation of the organisms on solid or liquid media. Chemolithotrophic species, such as Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans, or thermophilic chemolithotrophs, such as Acidianus brierleyi and Sulfolobus solfataricus can grow quite slowly, requiring weeks to complete efforts to identify and quantify these microbes associated with bioleach samples. Real-time PCR (polymerase chain reaction) assays in which DNA targets are amplified in the presence of fluorescent oligonucleotide primers, allowing the monitoring and quantification of the amplification reactions as they progress, provide a means of rapidly detecting the presence of microbial species of interest, and their relative abundance in a sample. This presentation will describe the design and use of such assays to monitor acidophilic microbes in the environment and in bioleaching operations. These assays provide results within 2-3 hours, and can detect less than 100 individual microbial cells.

Jan 1, 2009

By Elaine T. Cullen

Underground mining, like many high-risk industries, is facing a crisis in the near future. This industry has traditionally relied on a master-apprentice relationship to train new workers, but experienced miners are retiring in large numbers, leaving few "masters" to properly train their replacements. With a recent resurgence in mining, many new miners are entering the workforce each day. The rise in the number of inexperienced workers has implications for worker safety in an industry in which one mistake can blow up the entire workplace. The explosion in the Darby Mine in May 2006 that killed five miners illustrates what can happen in hazardous environments such as underground mines. The Health Communications Team at the National Institute for Occupational Safety and Health Spokane Research Laboratory was asked to address this problem by developing new training and safety awareness materials to promote safe flame cutting and welding practices. This article describes how occupational ethnographic techniques provided insights needed for "new product development." The result of this work was a national initiative to raise awareness and to protect underground coal miners from the dangers of flame cutting and welding in an environment filled with solid fuel and methane (natural gas). Although this project was initially designed for the mining industry, the approach and lessons learned are applicable to any high-risk industry and should be of interest to other social marketing or occupational safety and health professionals.

Jan 1, 2009

A sinter plant baghouse dust has been treated as a hazardous solid waste, and disposed at a very high price. A series of leaching tests were conducted to examine the possibility to produce high grade potassium chloride from the solid waste. It is found that around 40% of the solid wastes can dissolve into water, and a deposit with more than 90% KCl can be produced after simply drying the solution.

Jan 1, 2009

The largest investment in mining equipment in Caterpillar?s history ? The F series mechanical and electrical drive trucks ? is rapidly advancing. Caterpillar showcased the 793F and 797F mechanical drive trucks and the 795F ac electric drive truck at MinExpo in 2008 and have continued testing since then. The 793F and the 797F have accumulated more than 75,000 hours of field testing and have proven their performance capabilities and their durability. The new Cat C175 engine that powers them has racked up 130,000 hours of field testing in mining trucks and more than 120,000 hours in power systems. Because of the success of these field-follow programs, the 793F is targeted to go into full production within a few months and the 797F late this year. Caterpillar engineers have been testing two 795F ac prototypes at the Tucson Proving Grounds in Arizona. The development program has provided input for the construction of a new 795F ac in Decatur, IL. The new truck recently shipped to a copper mine in North America where it will serve as the first field-follow 795F ac as it works at the mine. The 313-t- (345-st-) capacity 795F ac will enter a new size class for Caterpillar, and, as a result, the primary focus of the Caterpillar ac electric program has been on the 795F ac. The commercial launch date will be defined as the field-follow program progresses. ?It?s fitting that soon after producing the 50,000th Cat off-highway truck, we are now shipping our first ultra-class ac electric drive truck to a mine,? said Chris Curfman, president of Caterpillar Global Mining. ?Our new trucks further solidify our position as the one manufacturer to provide unparalleled options and unmatched customer support.?

Jan 1, 2009