Search Documents

The development of information concerning mesothelioma in South Africa started with the 1959 finding of Dr. J. Christopher Wagner of cases of mesothelioma in persons living in the vicinity or working in crocidolite mines in Cape Province. After more than 40 years, the data from South Africa now provide important insights into the differences in mesothelioma risk associated with different asbestos fiber-types. Three case series reports and one analytical report were reviewed in this session. In total, information on 504 proven cases was presented. There were 28% of cases arising from occupational exposure in mining, 35% from non-mining occupations, 23% from environmental exposures; 14% where no exposure was established and 9% where the exposure was unknown. Among the 129 cases for which occupational exposure and asbestos fiber-type were established, 115 cases were associated with occupational exposure to Cape crocidolite; 1 case associated with occupational exposure to Transvaal crocidolite and 9 cases with occupational exposure to amosite (grunerite asbestos) and 4 cases with occupational exposure to mixed fiber-types. There were no cases associated with chrysotile asbestos. There were 33 cases of environmental mesothelioma linked to Cape crocidolite exposure and 2 to exposure to amosite and crocidolite but none to Transvaal amosite alone or to chrysotile. The evidence shows that amosite is capable of causing mesothelioma but that the major risk in South Africa is associated with Cape crocidolite.

Jan 1, 2008

By Julian Prada

Tunneling requirements are presenting designers with greater challenges. The design and construction of the 2000-ft long unidirectional twin highway tunnels for the approach to one of two bridges of the Louisville-Southern Indiana Ohio River Bridges (LSIORB) Project is no exception. Excavation under low cover, beneath an historic site, with each tunnel of 70-feet wide and 50-feet high dimensions will set precedents for US highway tunnel excavation size. To investigate ground conditions to supplement final design of the highway tunnels, an exploratory tunnel excavated through karstic limestone and shale will be located within the confines of the proposed final alignment. With the LSIORB Project, Jefferson County, Kentucky and Clark County, Indiana will have improved cross-river mobility between them. The Indiana Department of Transportation (INDOT) and the Kentucky Transportation Cabinet (KYTC) are developing the LSIORB Project jointly, in coordination with the Federal Highway Administration (FHWA). Section 4, one of six sections, as shown in Figure 1 is the East End Kentucky Approach and Connections to I-265. Key elements of Section 4 are the twin three-lane highway tunnels under the historic Drumanard Estate. The property is located on the north side of US Highway 42 (US 42) at the intersection with the Gene Snyder Freeway (also KY841) as shown in Figure 2. One aspect of the project consists of the excavation of an Exploratory Tunnel along the southbound alignment tunnel. At the time of preparation of this paper, KYTC has not awarded the Exploratory Tunnel Contract. This paper will focus on the planned geotechnical investigation program that will occur during excavation of the exploratory tunnel and how the design of the twin highway tunnels will incorporate the findings to achieve an innovative and efficient configuration.

Jan 1, 2008

All aspects of precious metals processing were featured at a symposium held Oct. 3-6, 2007, at Loews Ventana Canyon Resort in Tucson, AZ. Although billed as "Precious Metals Processing: Advances in Primary and Secondary Operations," the symposium also looked at economic, regulatory and environmental issues affecting the precious metals industry. The symposium was sponsored by SME; The Minerals, Metals & Materials Society (TMS); and the International Precious Metals Institute (IPMI). It included workshops, technical presentations, guest speakers and social activities. Mining industry management, process engineers, equipment manufacturers, consultants, metals marketers, academics and others involved in the precious metals industry attended the conference. Needless to say, with gold nearing $25.721g ($800/oz) and platinum pushing $41.801g ($1,300/oz) at the time of the meeting, the mood among the attendees could not have been more positive. The symposium was privileged to have Father Ernest S. Sweeney, professor of Latin American History at Loyola Marymount University, as a guest speaker. Sweeney, a Jesuit priest, provided a colorful account of the history of mining in Arizona and the surrounding region of North America (Fig. 1). He described the importance of the mining industry and said, "To go down into the bowels of the earth to extract its riches for the benefit of all of us is an awesome task deserving our sincere respect and gratitude." However, he warned the industry that: "The ever increasing de¬mands on the mining community for the protection of the environment calls for endless efforts to maintain ethical standards in a business filled with risk, uncertainty and frustrations." Sweeney noted that the Spanish conquest of the Americas was driven by the three fundamental motives of "God, glory and gold." He noted that gold was the basic, most powerful driving force of the conquest and occupation of the Spanish empire. The first European to explore Arizona was the Franciscan missionary Marcos de Niza. He came to Arizona in 1539 in search of the fabled Seven Golden Cities of Cíbola. Sweeny noted that Spanish explorers were consumed, as Cortes himself described it, "with a burning fever that only gold could cure." Sweeney told the story of some of these early explorers, including Francisco Vázquez de Coronado who "mounted an expedition in pursuit of gold and rich empires to conquer." Coronado passed through Arizona and discovered the Grand Canyon. "Coronado returned to Mexico exhausted, bankrupt and disillusioned, but with a wealth of new knowledge of the borderlands of the Spanish empire," said Sweeney. He then described the colorful history of early gold, silver and copper exploration and mining in Arizona, including the famous tale of the Lost Dutchman's Mine. In a luncheon address, David Kanagy, SME's executive director, introduced the attendees to the upcoming OneMine. org Web site. Kanagy told the audience" One-Mine.org will be a collaborative digital library that will

Jan 1, 2008

When the 2008 Olympic Games begin in Beijing, China is September it will not only mark the end of the journey for the Olympic torch and the thou-sands of participating athletes, but the games will also mark the culmination of a massive amount of construction in the city. On display for the world to see will be 31 new and refurbished venues including the 91,000-seat National Stadium called the ?Bird?s Nest? and the aquatics center, called the Water Cube. What will not be featured as prominently on the television cameras broadcasting the games around the world will be the network of tunnels built beneath the city. But that infrastructure of rail lines will be of critical importance to the games. While preparing to host the world, China added a subway tunnel that will include four stops in the Olympic Park. The 4.4-km (2.7-mile) subway line that runs through the complex of stadiums, gymnasiums and parks began trial operations in June. Prior to the opening of that line, Beijing's No. 5 subway line, which runs through the heart of the city from north to south, opened in October. That 27.6-km (17-mile) line took nearly five years to build and includes 23

Jan 1, 2008

By P. W. van Deventer

?Soil quality is the capacity of a soil to function, within ecosystem and land use boundaries, to sustain biological productivity, maintain environmental quality, and promote plant, animal and human health?. In the long-term, vegetative rehabilitation of mining wastes aims at, as far as possible, the proper ecological integration of the reclaimed area into the surrounding landscape, which is sustainable and requires minimal maintenance. A certain succession pattern is therefore needed. Recent ecological concepts recognize the role of the substrate?s quality and nutrients in affecting the rates and directions of succession patterns. Although pedogenesis and eventually soil quality in mine waste are not well known, monitoring of soil quality parameters in kimberlite mine tailings reveal a remarkable establishment and or improvement of specifics oil quality indicators. During the same time the vegetative cover?s total functionality as well as reproductive ability improved. Functions of soil, and thus soil quality, can be assessed at the field, farm, ecosystem, pedosphere, and global scale. It is recognized, however, that management of soil becomes increasingly difficult at larger scales, but for demarcated mine waste sites it is possible to ameliorate and manage and assess soil functions and quality. Therefore the significance of the study is the following: soil functions and quality become inseparable from the idea of system sustainability, and are considered as key indicators of ecosystem sustainability on rehabilitated mine tailings material.

Jan 1, 2008

By Joseph Poplawski, Christian O’Keefe, Robert Maron

"Unique and difficult minerals processing measurement situations will be described and the application of passive array-based technology for performing these measurements will be illustrated. Examples of these situations include volume flow measurements in froth lines and flotation feed lines with entrained air, slurry lines with magnetite and other magnetic ore, slurry lines with abrasive or corrosive materials, high pressure lines, and slurry and non-slurry lines exhibiting scale buildup. Other situations include measurement of entrained air levels in pipes and in flotation columns. These measurements are achieved through CiDRA’s patented passive sonar array-based technology. This technology performs two independent measurements – flow rate and entrained air amounts. Two hardware implementations of this technology have resulted in a non-intrusive flow and entrained air meter which easily is installed on the outside of the pipe, and a submersible version for entrained air or gas holdup measurements which is used in flotation processes. Recent developments in extending this technology to solve other unique measurement problems such as valve movement confirmation will be covered.INTRODUCTIONThe minerals processing industry faces many unique and challenging process control conditions and environments. In terms of flow measurements, many of these situations are not being properly served by traditional flowmeters such as ultrasonic meters, magmeters, turbine meters, orifice plate meters, vortex flow meters, Coriolis flow meters, and venturi meters. A new class of flowmeters has been developed that solves these unique situations and flow measurement problems. This new class of flowmeter technology utilizes sonar-based processing algorithms and an array of passive sensors to measure not only flow, but also fluid composition. It does so accurately, reliably and without making contact with the fluid. These measurements are performed on practically any type of fluid within virtually any type of pipe.PRINCIPLE OF OPERATIONSonar array-based flowmeters are ideal for tracking and measuring the mean velocities of disturbances traveling in the axial direction of a pipe. These disturbances generally will convect with the flow, propagate in the pipe walls, or propagate in the fluid or slurry. First let us focus on the disturbances that convect with the flow. The disturbances that convect with the flow can be density variations, temperature variations or turbulent eddies. The overwhelming majority of industrial flows will have turbulent eddies convecting with the flow, thus providing an excellent means of measuring the flow rate as described below."

Jan 1, 2008

By B Vorster

Falls of Ground is one of the highest causes of incidents, accidents and fatal injuries in our mines today. These falls of ground may occur as soon as the face is exposed after blasting or after machine cutting. The falls of ground can also occur after support has been installed. There are many reasons why these falls occur before and after supporting of the face. It is therefore important to support the exposed face as soon as possible to prevent the falls of ground. It is also very important to support the face with the correct support products and to support the face as designed and required by the mining engineers. The possible reasons for falls of ground, possible support methods and the products available will be discussed in this presentation. In typical conventional narrow vein stoping operations, the use of conventional temporary support components to offer some support to workers, whilst the permanent and generally more elaborate support system gets installed or constructed, still results in injuries to people. The author wishes to discuss the following items in this paper:- ? Introduction ? Basic face behaviour after exposure ? Controllable Parameters ? Mining Engineers support designs ? Primary and Secondary Support ? Products available for prevention of falls of ground

Jan 1, 2008

By V N. Rudashevsky, F Melcher, J Lodziak, D Klosa, N S. Rudashevsky, M Sitnikova, L Gast

A combination of novel and æclassicÆ methods, namely electric pulse disaggregation (EPD), hydroseparation (HS), preparation of monolayer polished sections, and mineral liberation analysis (MLA) was employed to study ores from platinum pipes (Bushveld Complex, South Africa), pristine PGE mineralisation of the Main Sulfide Zone (Great Dyke, Zimbabwe), as well as ancient and modern gold/PGM placer deposits. It is shown here that the EPD technique liberates mineral grains of interest without any visible destruction allowing the study and analysis of individual rock-forming and ore minerals, in our case especially platinum-group minerals. The HS method is an effective tool in concentrating heavy minerals by factors up to 10 000 fold. As near-total recovery of grains >10 ¦m is achieved, the nugget effect can be overcome also in case of limited availability of samples (drill core, museum specimens). The MLA technique is a fast tool to detect and characterise mineral phases in ores and ore processing products. Many mineralogical parameters of individual grains and mineral assemblages can be deducted and documented. The results show that the techniques employed, either on their own or in combination, provide a wide range of additional information especially on platinum ores which is beneficial to both the researcher and the metallurgist.

Jan 1, 2008

By J. Danoczi

Specially designed X-ray machines are used extensively on diamond mines for the recovery of diamonds from ores. These machines are extremely expensive and, at present, there are no reliable methods of determining if the equipment is performing efficiently. The objective of this work was to manufacture translucent X-ray diamond simulants, which would emit varying but known luminescence signals when exposed to X-rays. These X-ray diamond simulants could then be used to determine the efficiency of diamond recovery operations.

Jan 1, 2008

By Xinzhi Du

Coal strength is essential to analyze the stability of excavation in coal. It is well known that the strength of coal tested in the laboratory is size-dependent, and different size specimens will produce different strength. Many researchers have studied the uniaxial compressive strength of coal and developed a number of empirical formulae to describe the strength variation with specimen size. According to a comprehensive data base that includes most of the laboratory testing results in the last century in U.S. and South Africa, the size effect and shape effect were reviewed and analyzed. The results show that different groups of coal specimens have different size effect on the compressive strength. The critical size for the size effect from the data analysis is about 40 in. The shape (W/H) of the specimens has a large effect on the compressive strength. The pillar strength formulae obtained from the data regression have a larger strength than all other existing formulae. Most pillar strength formulae have their own place in coal pillar design field. In order to analyze the difference of those formulae, twelve design formulae have been selected to compare using the Pittsburgh coal seam. The intention is not to determine the preferred formulae, but only to compare them, and see how do the W/H ratio, width, length, angle, cross-section area and effective width affect different pillar strength formulae?

Jan 1, 2008

By Tamara Whitaker, James Gunderson, Ruilin Yang

This paper presents the results of a vibration control project conducted in soft overburden at a surface coal mine located in the western United States. The study uses near-field blast vibration monitoring, analysis and modeling techniques developed in house. Accelerometer-equipped seismographs were utilized for near-field vibration monitoring and analysis. Vibration control was achieved through field data regression as well as vibration modeling using the multiple seed near-field blast vibration model (Yang and Scovira, 2007). The regression was conducted between peak particle vibration parameters and the minimum scaled distance per delay. From the regression analysis, the curves of upper bounds for peak particle vibration parameters and charge weight were developed. The dominant frequencies of the blast vibration were also addressed in this project. The regression curves and near-field vibration model guided the blast design to control blast vibration for maximizing the recovery of coal and maintaining mine productivity.

Jan 1, 2008

By Dan Payne

The Crinum mine has recently completed workings in the southern area of the mine. Over the 10 years of longwall production 40 million tonnes have been extracted and the mine has experienced over 40 longwall face, 3 main gateend, and 2 tail gateend roof falls as well as 5 roadway roof falls away from the longwall. Weak roof (less than 10MPa (1450psi) in the bolted horizon) has been the principal roof control issue at the mine. However, weak, highly cleated coal, water inflow from overlying aquifers, some minor structure and a diatreme in the main headings have also contributed to the challenges at the mine. This paper describes the geotechnical experience over the 10 years, the mine?s approach to addressing the issues and the relative success of these approaches.

Jan 1, 2008

By D. I. Smith

Constructing tunnels in congested urban areas requires tunnels to be placed closer together and with less cover than was previously necessary. Contract CQ031 of New York?s East Side Access project will construct four six-meter diameter bored tunnels in a three-up one-down ?T? configuration, with less than three meters of soil between the tunnels. Mixed-face rock and glacial till conditions with a high ground water table will be encountered under active railroad yards. The tunnels will also pass beneath the busiest railroad interlocking in North America with cover as shallow as three meters. This paper discusses the challenges of designing segmentally lined tunnels for these conditions.

Jan 1, 2008

By Peter Swanson

A seismic monitoring network has been installed in western Colorado (USA) in the vicinity of three underground coal mines to (i) distinguish and characterize seismic activity as either mining related or naturally occurring, (ii) implement a real-time event monitoring and notification tool, and (iii) collect data for use in research studies aimed at quantifying impacts from mining-related and natural seismicity. These potential impacts include dynamic rock mass failures such as coal bumps as well as strong shaking in the vicinity of critical structures such as impoundment dams, reservoirs, mine seals, mine openings, and steep slopes. Examples of two damaging seismic events are presented and the mining and geologic factors attending these dynamic failures are described.

Jan 1, 2008

By Ming Ju Liu

China has been suffering from the most serious coal and gas outburst accidents. The situation has become worse than ever with the mining of deeper coal seams at higher production rates in a more complex underground mining environment, in order to meet the huge national demand for coal-fuelled power plants. In the year 2007 alone, more than 30 outburst accidents occurred in underground coal mines with a death toll of 258, and in the year 2008, as of May 22, nine outbursts have already occurred in Henan, Hubei and Chongqing, killing 68 workers. At the same time, China also experienced new trends of coal and gas outburst accidents since its coal production boom in the year 2001. These trends are of great importance for government agencies, coal mine owners and operators to take initiative and effective measures to prevent and control the occurrence of coal and gas outbursts in China?s widely spread outburst prone mining areas. This paper presents outburst data of China coal mines since 2001 and describes new trends of outburst occurrence in recent years, which include outbursts coupled with shocks or rock bursts of competent roof, outbursts in mines under development, outbursts in new mines and mines that have never suffered outbursts before, outbursts in mines that are believed to be of low gas content as well as outbursts in more long-wall faces. Based on the observation of outburst occurrence in China in the period from 2001 to 2008 as well as mining and geological conditions, detailed analysis of the possible causes that led to those new trends of outburst accidents is conducted. The analysis helps shed light on possible future remedies and the necessary measures to alleviate or eliminate outburst accidents in underground coal mines. Suggestions are put forward on future studies that could be of interest to national and provincial government agencies regarding strategic policies, proper technical management practice, identification of outburst prone coal seams, online monitoring of impending outbursts as well as prevention and control measures.

Jan 1, 2008

By Rudi Podjadtke

In a short chronological review the development concepts and improvements in steel roadway support are shown. The successful standardization concept of RAG Deutsche Steinkohle and currently used support systems are important topics. The history of optimizing the material properties for the steel arch support with different alloys up to the tempering used today is discussed. The present-day application of the steel support is additionally presented. Today, it represents a system component of modern roadway support also for highly stressed roadways. In addition to the yielding roadway arch support, this overall system - the combination support - consists of the additional components of a rockbolting system and concrete backfilling. The comparison of the application areas for each individual partial system with the overall system illustrates its high performance capability. Actual practical experience with the state of the art typed steel arches are pointed out exemplarily. Understanding the complete system permits the selection of the economically optimal support for all conditions.

Jan 1, 2008

By B. V. Driga

The paper presents the evaluation method of the thermal power potential of the salt lakes developed in collapsed salt mines in Romania. It is well-known that the hydro-chemical stratification of these lakes favors warmer internal layers. The degree of heat varies during the year, but, taking into account the large number of genetic lakes of this type, it can be used as a local utilizable power source. The authors analyze the correlations between the physico-chemical parameters of the water and the degree of heat stored as a function of the morphological parameters of the lakes, as well as the technical parameters for capitalizing on this power.

Jan 1, 2008

By Paul J. Axtell

The results of in-situ geophysical cross-hole tests on improved soil by soil mixing (SM) and jet grouting (JG) are described. This testing was conducted on soil improved by SM and JG columns constructed in the downstream free-field of Tuttle Creek Dam near Manhattan, Kansas as part of the seismic retrofit. Results of similar geophysical testing performed on untreated soil in the vicinity of the Downstream Test Program (DTP) area, as well as beneath the embankment at several locations, are also described and used for comparison purposes. In-situ shear moduli are also compared with those determined in laboratory resonant column tests. The increase in stress wave velocities and associated shear moduli by SM and JG treatment are presented for use in liquefaction potential and seismic deformation analyses of SM or JG treated soil. This data is required to determine the decrease in liquefaction potential and earthquake-induced permanent deformations due to SM or JG with respect to that of untreated soil.

Jan 1, 2008

By T. W. Beck

Overexposure to respirable dust remains a widespread health hazard to roof bolter occupations in underground coal mines. Recently implemented mist drilling technology was evaluated for its effectiveness in controlling respirable dust exposures for roof bolting personnel. This work presents the findings from NIOSH field and laboratory studies comparing respirable dust levels on mist drilling roof bolter machines to dust levels measured on machines using a conventional vacuum drilling system. Gravimetric and instantaneous respirable dust samples were collected for multiple drilling cycles. These dust measurements were used to assess the potential dust control capabilities relative to conventional drilling. Controlled laboratory tests found 0.3 mg/m3 more respirable dust with mist drilling than with the conventional vacuum method. A separate field investigation of the two techniques observed higher dust levels around the mist bolting machine.

Jan 1, 2008

By L. Nichols, H. Keele, K. Czajewski

"The oil sands industry in northern Alberta disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called consolidated tailings or composite tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long-term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long-term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities.Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are longterm stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface.The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process."

Jan 1, 2008