Search Documents

By B. P. Watson

The first crush pillars on the Bushveld platinum mines were introduced at Union Section in 1978. Before the introduction of crush pillars, serious problems were experienced when stoping advanced to a point 30 m to 40 m on both sides of the centre gully. At least three to four stopes were collapsing per month. The introduction of the pillars stopped the stope collapses in the mining area where they were introduced. The residual stresses of these pillars were never measured; however, the successful elimination of the ?back-break? problem suggests that the original pillars had a residual strength of at least 8 MPa. Apart from back analyses, very little work has been done to determine the residual strength of crush pillars and only very recently have any measurements been made. The lack of knowledge in this field has resulted in pillars being designed based on experience. Concerns about stope collapses, similar to the Coalbrook disaster, have led to larger pillars being cut in more recent times. If such pillars were cut in brittle quartzites they would always fail violently but the ductile nature of the Merensky Reef generally allows large pillars to fail without bursting. Occasionally, however, one would burst in a working area. Increased incidence of bursting has been reported on some mines at deeper levels but most of these bursts occur in the back areas. Nevertheless, the incidence of bursting increases the risk of falls of ground in already dangerous areas, and the larger pillars decrease the extraction ratio. This paper describes the evaluation of stress measurements conducted in two boreholes over a crush pillar with dimensions 2.5 m x4.0 m, and a height of 1.2 m. Boussinesq equations for vertical and shear stress were used to analyse the original measurements and provide a stress profile across the pillar as well as the residual strength of the pillar. The results showed an unexpectedly high peak stress of 280 MPa at the centre of the pillar and a residual strength of 48 MPa. The reason for the high residual strength is suspected to be the result of the stiff environment under which the pillar failed and the small height of the siding on the up-dip edge of the pillar. More measurements should be conducted on several mines to establish a range of residual strengths for narrow crush pillars.

Jan 1, 2008

By L. van Dyk

The project was aimed at evaluating the double-header trains implemented at Great Noligwa mine, looking at the changes from the old conventional trains to the new trains, and identifying possible improvements to obtain an even better and more productive tramming system. The methods used to evaluate the double-header trains at the mine included personal observations, time studies, personal interviews, technical research, safety analysis, cost analysis, production analysis, breakdown analysis, break test analysis, comparisons and working closely with engineering department and manufacturers. Issues that were evaluated are the improvements in safety, cost reductions, tramming congestion reductions, better efficiencies, labour optimization, enhanced driver safety and maintenance. Shortcomings of the double-header trains were identified and recommendations made to improve on the shortcomings. Findings of the evaluation study indicated the following: ?Drastic improvement on safety ?Extreme cost reductions ?Reduction in tramming congestions and bottlenecks ?Better tramming efficiencies ?Optimized labour placement ?Enhanced driver safety ?More effective maintenance. Although there is room for improvements, the double-header trains were implemented with great success at Great Noligwa mine. It is currently the preferred tramming methodology at Great Noligwa mine, and is also implemented at other Anglo Gold Ashanti?South Africa shafts. This tramming system has huge potential for growth, not only in Anglo Gold Ashanti, but in all other older mines that experience major tramming problems.

Jan 1, 2008

By E. Marcoux, F. Lotfi, A. Belkabir, L. Maacha, A. C. Brown, S. Brunet

"Koudiat Aïcha is a small Zn-Pb-Cu deposit, enclosed in the Visean Sarhlef volcano-sedimentary series of the Moroccan Hercynian Jebilet massif. Base metal mineralization is located between a basal unit consisting of black argillite with arenite intercalations, and an upper unit composed of black argillite with locally fossiliferous calcareous units towards the top. Paraconcordant gabbro sills are present in both the upper and basal units, and the enclosing strata. Three successive phases of deformation linked to regional deformation overprint the volcano-sedimentary rocks and gabbros, as well as the sulfide mineralization.The mineral deposit includes several lenses of massive to semimassive pyrrhotite, 1 to 20 m thick, with a large halo of disseminated sulfide veinlets and sulfide nodules within a zone of intense chlorite alteration in the footwall. The ore mineralogy consists of massive to semimassive pyrrhotite with lesser amounts of sphalerite, chalcopyrite, arsenopyrite, galena, pyrite, and stannite.Lead isotope results (206Pb/204Pb averaging 18.27) suggest that the metals of the Koudiat Aïcha deposit are derived from the volcano-sedimentary host rocks. Sulfur isotopes also indicate a volcano-sedimentary origin, with bacterial reduction of sulfate (d34SCDT = -7.5‰ to -10.5‰). The conditions for sulfide meta-morphic equilibration range from 250° to 330°C (sphalerite and chlorite geothermometers). The gabbroic sills could have been a local heat source for hydrothermal circulation. Based on these geological and mineralogical features, a Besshi-type model seems appropriate for the genesis of the Koudiat Aïcha mineralization.Koudiat Aïcha est un petit dépôt de Zn-Pb-Cu, encaissé dans la série volcano-sédimentaire Viséenne de Sarhlef dans le massif Hercynien de Jebilet au Maroc. La minéralisation en métaux usuels se situe entre une unité basale d’argilite noire interlitée d’arénite et une unité supérieure composée d’argilite noire comprenant localement des calcaires fossilifères près de son sommet. Des sills de gabbro paraconcordants sont présent à la fois dans les unités basale et supérieure, ainsi que dans les strates environnantes. Trois phases de déformation successives associées a la déformation régionale superposent leurs effets sur les roches volcano-sédimentaires, les gabbros, ainsi que la minéralisation sulfurée. Ce gîte comprend plusieurs lentilles de pyrrhotite massive a semimassive de 1 a 20 m d’épaisseur au sein d’un large halo de veinules de sulfures disséminés et en nodules au sein d’une zone intensément chloritisée dans le mur du gisement. Le minerai consiste en pyrrhotite massive à semimassive avec des quantités subordonnées de sphalérite, de chalcopyrite, d’arsénopyrite, de galène, de pyrite, et de stannite. Les résultats de l’analyse des isotopes du plomb (206Pb/204Pb moyen de 18.27) suggèrent que les métaux du gîte Koudiat Aïcha proviennent des roches volcano-sédimentaires encaissantes. Les isotopes du souf¬fre indiquent eux-aussi une origine volcano-sédimentaire, impliquant la réduction bactérienne des sulfates (d34SCDT = -7.5‰ et -10.5‰). L’équilibration métamorphique des sulfures s’est produite entre 250° et 330°C (géothermomètres à sphalérite et chlorite). Les sills de gabbro pourraient avoir été la source de chaleur locale responsable de la circulation hydrothermale. Sur la base de ces caractéristiques géologiques et minéralogiques, il semble approprié d’invoquer un modèle de type pour Besshi pour expliquer la genèse de la minéralisation de Koudiat Aïcha."

Jan 1, 2008

By P. C. Holloway

La Oroya zinc ferrite (19.5% Zn, 26.6% Fe, 0.052% Ga, 0.075% In) was roasted with coal under conditions more oxidizing than normally used in a Waelz kiln, and the roasted residues were leached with 200 g/L H2SO4. Overall zinc recoveries of up to 97% were achieved, with 35% of the zinc reporting to the fume after roasting at 1,100°C with a bituminous coal addition of 20%. Under these conditions, 93.2% of the Cd, 13.4% of the Cu, 33% of the Ga, 61% of the In and 18.2% of the Pb were recovered either in the fume or in the leach solution. At 2006 metal prices, the value of the recovered metals is comparable to that obtained from commercial Waelz kiln processing of this residue. Zinc in the franklinite (ZnFe2O4) mineral is reduced to zinc vapor, and, after oxidation, some of the zinc is found as ZnO or as Zn2SiO4 in the roasted residue. Iron reacts to form either hematite (Fe2O3) or magnetite (Fe3O4), with no metallic iron detected in the roasted residue, and less than 2% of the iron is solubilized during leaching. The residue produced after roasting and leaching is, therefore, much more stable than the residue from Waelz kiln processing and should be suitable for disposal in a landfill.

Jan 1, 2008

By GA Harrison

The introduction of Extra Low Profile (XLP) mechanised equipment within Anglo Platinum is aligned with the overall New Mining Technologies strategy to focus on continuing modernization of our mining operations to achieve injury free sustainable production and cost effective mining technologies. The method allows for the introduction of a suite of XLP and Low Profile (LP) equipment in a narrow reef (1,2m) mining environment. For the first time it is now possible to achieve total trackless mechanisation at these stoping widths and XLP Breast mining has the potential to add more value when benchmarked with conventional mining and other mechanised methods. Various types of XLP equipment were tested at different sites within Anglo Platinum and this paper describes the XLP equipment evolution to-date. It concludes with recommendations on our future strategy regarding implementation and roll out of the XLP technology within Anglo Platinum.

Jan 1, 2008

By Martin Herrenknecht

Tunnel boring machine (TBM) development continues to take on not only larger diameters, but also more difficult ground conditions. Ground conditions consisting of unstable faces with water pressures up to 15 bar have required innovative design approaches. A systems approach has been required to produce tunneling machines that can safely excavate the tunnel in an efficient, cost-effective manner that stresses production and labor saving approaches. This article reviews the current design developments and present recent projects where these most recent principles have been applied. The world?s growing population and rapidly proceeding urbanization are boosting an enormous demand for new and high-capacity infrastructures to secure the mobility of goods and people. Densely populated areas face the challenge of providing efficient traffic infrastructure such as a modern public transport system. At the same time, the maintenance and modernization of supply and disposal structures for water, sewage, energy and communication are essential. Last but not least, are supra-regional transportation routes such as long distance water diversion schemes. All of these projects are as demanding and are characterized by a tight time schedule. In this context, the demand for efficient tunnels for traffic and utility lines is increasing, as new infrastructures often leads underground because of limited space above ground. Also, tunnels are the obvious choice to cross natural barriers like mountain ranges. To handle the complex and variable geological conditions and other constraints, such as low overburden, high water pressure or long tunnel drives while facing increasing demand of a quick completion of a project, mechanized tunneling sets standards regarding safety, profitability and environmental protection in traffic tunneling projects as well as in the trenchless construction of utility tunnels. Different machine types and working principles have been developed to master various geological and hydrogeological requirements. Continuous activity in research and development leads to constant improvement of the mechanized tunneling process.

Jan 1, 2008

By T. M. Barczak

Pumpable roof supports provide an alternative approach to secondary support in underground mining. Unlike all other supports that are either partially or fully prefabricated prior to being transported into the mine, the pumpable support is fabricated in place in the mine entry. This reduces the underground material handling efforts and thus the injuries historically associated with in-mine support construction. On-site fabrication also facilitates application of the support in areas that are inaccessible to transportation equipment such as scoops or rail cars, making it ideal for many bleeder applications. One of the main advantages of the pumpable support is that it fully bridges from the mine floor to the roof, thereby eliminating the requirement of ?topping off? the support with wooden wedges or crib blocks that soften most other support responses. This report examines the development of modern pumpable roof support technology and provides a full description of the performance capabilities of each of the support products now on the market.

Jan 1, 2008

By A. Schaum

On average, there are approximately 10 fatal haul truck accidents per year. The most common causes for haul truck accidents include mechanical problems, inadequate training and insufficient road/berm maintenance. Due to the frequency and magnitude of haul truck accidents, new training methods are being investigated. With the widespread availability of computers and new technology becoming more reasonably priced, the ability to incorporate computer-based training for miners is becoming more possible. It has been shown that computer-based training is just as effective in knowledge acquisition as traditional lectures, and computer-based training can lead to a significant increase in the retention of material (Williams and Zahed, 1996). Studies have also shown that more engaging training methods lead to more effective knowledge acquisition (Burke et al., 2006). A supplemental system for current and new miner training to address the common causes of fatal accidents was developed. The training system is a virtual preshift inspection of a haul truck, and it can train new haul truck operators to identify parts that look defective. The training will increase an operator?s ability to recognize problematic parts and correctly identify the corrective action needed. Increasing the quality of training by providing an engaging, simulated hands-on environment will lead to safer behaviors by trainees, which will ultimately lead to fewer accidents and fatalities.

Jan 1, 2008

By G. L. Smith

This paper introduces and defines the concept of a linkage between long-term planning parameters (?global assumptions?) and possible future world views as conceived in scenario planning. Scenario planning, the tool that is used to arrive at plausible future worldviews, is described in the context of the platinum industry. The interpretation of the scenarios into long-term planning parameters is made, followed by an illustration of how the long-term planning process has been adapted at Anglo Platinum to include the notion of uncertainty.

Jan 1, 2008

By M. A. Barakat

"Adsorption of heavy metal ions specifically, Cu(II), Zn(II), Mn(II), and Cr(VI) from aqueous solution on synthetic 4A Zeolite was evaluated. The 4A zeolite was synthesized previously by dehydroxylation of low grade Kalabsha Kaolin at 800 °C, and reacted hydrothermally with 2-4 M NaOH solution at 100 °C for 2h. The adsorption capacity of the metal ions were found to be strongly dependent on pH and initial metal ion concentration. At the optimium conditions the adsorption capacity decreased in the order Cu(II) > Zn(II) > Mn(II) > Cr(VI) ions. Almost complete adsorption was achieved for both of Cu(II) and Zn(II) ions at pH > 6, while the adsorption capacity for both Mn(II) and Cr(VI) was 96, and 55.3 % at pH 11 and pH 3, respectively. The results also showed that the grain size of the 4A zeolite has a little effect on the adsorption capacity. The experimental data was compared with two adsorption isotherms, Langmuir and Freundlich isotheroms. The results showed a good agreement of the Langmuir plots with the experimental data.1. IntroductionSeveral industrial wastewater streams may contain heavy metals such as Cr, Cu, Pb, Zn, Co, Ni, Mn, etc. including the waste liquids generated by metal finishing or the mineral processing industries. Heavy metals are considered hazardous pollutants due to their toxicity, even at low concentration, and nonbiodegradability. Increasing level of heavy metals in natural water bodies poses a serious threat to all living species including humans. It is, therefore, essential to reduce the heavy metal concentration in effluents/wastewater before it is discharged into the water bodies [1]."

Jan 1, 2008

By H. Sarvamangala

Biomineralization of manganese on titanium condenser material exposed to seawater has been illustrated. Biom-ineralization occurs when the fouling components, namely, the microbes, are able to oxidize minerals present in water and deposit them as insoluble oxides on biofilm surfaces. Extensive biofilm characterization studies showed that an alarmingly large number of bacteria in these biofilms are capable of oxidizing manganese and are, thereby, capable of causing biomineralization on the condenser material exposed to seawater. This paper addresses studies on understanding the exact role of the microbes in bringing about oxidation of manganese. The kinetics of manganese oxidation by marine Gram-positive manganese oxidizing bacterium Bacillus spp. that was isolated from the titanium surface was studied in detail. Manganese oxidation in the presence of Bacil-lus cells, by cell free extract (CFE) and heat-treated cell free extract was also studied. The study confirmed that bacteria mediate manganese oxidation and lead to the formation of biogenic oxides of MnO2, eventually leading to biomineralization on titanium surface exposed to seawater.

Jan 1, 2008

By D. Janicijevic

This paper describes the process of scraper winch pull force measurement and shows the results of the actual winch pull force in extreme stall situations as well as during the face and gulley cleaning. It was found that by slowing down the motor and causing it to slip, torque up to 3.5 times higher than the nominal can be developed, resulting in the same increase of winch pull force. On the other hand, measurements of the actual force needed for cleaning of the face and the gully have shown that the currently used winches are too powerful. The extra torque that can be developed by the already too powerful winch motor poses a significant danger and necessitates the implementation of measures that will eliminate this risk.

Jan 1, 2008

By D. Mohapatra

The possibility of using 2,2,4-trimethyl-1,3-pentanediol dissolved in tetrachloromethane as extractant for boron recovery is discussed. The parameters optimized for this purpose are contact time, boron concentration in the aqueous phase, extractant concentration, equilibrium pH and phase ratio. NaOH is used as stripping agent for boron recovery from the loaded organic phase. Boron extraction is found to be a slow process (equilibrium time 20 minutes) compared to boron stripping, which is reasonably fast (equilibrium time 5 min). Maximum boron extraction is possible at a broad pH range from 1.0 to 6.0. Using 1.0M extractant concentration, a 1:1 phase ratio (organic: aqueous) and two stages, ~99% boron extraction is achieved. More than 97% boron stripping is possible using 0.5M NaOH at a 1:1 (organic: aqueous) phase ratio in two stages. Overall, a 95.6% boron recovery was achieved. Loss of solvent into the aqueous phase and co-extraction of Ca, Na and K into the organic phase at higher equilibrium pH are two major concerns in his process.

Jan 1, 2008

Ceremonies for the induction of four mining industry pioneers into the National Mining Hall of Fame will be held Saturday, Sept. 13, 2008 at the Charles F. Barber Pavilion of the Museum Convention Center in Leadville, CO. This will be the 21st Annual National Mining Museum and Induction Banquet. The four inductees are Lew Eklund, 76, Carrie Jane Billings Everson (1843-1914), ?Colonel? William C. Greene (1851-1911) and Arthur L. Hawkesworth (1860-1905). Lew Eklund founded Eklund Drilling that is now based in Elko, NV. He invented many designs that play a major role in today?s mining industry. His Cyclo Blower and various sampling devices he designed helped to revolutionize gold deposit exploration by allowing mining companies to effectively sample microscopic gold. Carrie Jane Billings Everson discovered and proved a method for bulk oil flotation concentration of mineral ores, the precursor to modern froth flotation methods of minerals concentration. She patented her process in 1886. In the early 1890s, coworkers built and operated demonstration plants incorporating her bulk oil flotation process. ?Colonel? William C. Greene was responsible for the development of the great copper mining properties of Cananea, Mexico. In seven years, he went from ragged cattleman and adventurer to the greatest captain of industry the borderlands have ever seen. Arthur L. Hawkesworth was a master mechanic for Anaconda Copper. He invented the detachable drill bit. His invention generated tremendous savings for the mining industry in time, in dollars and in safer operating conditions underground. His bit?s long lasting contribution to improved mine economics is immeasurable. The 21st Annual National Mining Museum and Induction Banquet will begin with an open house and reception at 5:30 p.m. followed by the dinner and program at 7 p.m. The inductions will bring to 201 the number of mining ?greats? whose engraved photographs and biographical sketches are installed in the National Mining Hall of Fame.

Jan 1, 2008

By Alan D. Fisher

Amtrak made a decision to replace an aging bascule bridge with a vertical lift bridge for their crossing of the Thames River in New London, Connecticut. The new lift bridge occupies the same alignment and shares the same foundations as the bascule span. During construction the deep foundation caisson supporting the bascule span settled and tilted. Investigation into possible reasons revealed interesting historical facts, both of the construction of the innovative open well caisson foundations and of the state-of-the-art in tremie concrete placing methods in use at the turn of the century. This paper describes both of these topics.

Jan 1, 2008

By M. Olper

The change in regulations and the strong attention to the environment have suggested some changes in the traditional processes for the recycling of lead acid batteries. Engitec Technologies, marketing the Integrated CX® System, is continuously updating and improving its technology to fulfil the technical, economical and ecological requirements coming from the market and from the environmental authorities. In this paper Engitec Technologies will present the latest technical innovations introduced in the Integrated CX® System.

Jan 1, 2008

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Ertugrul Kaya, Kagan Ozdemir

The results of bench blasting on quarries, have important influences on the performance of subsequent mining activities such as loading, hauling, crushing, grinding etc., and the total costs of that mine. Drilling and blasting is an important step in mine producing chain and its results such as fragmentation, muckpile shape and looseness, dilution, damage and rock softening effect the efficiency of downstream processes. Within the scope of this study, the three different hydraulic excavators’ working performances have been studied considering the particle size distribution after bench lasting at a quarry in Istanbul Turkey. Five shots have been realized on the quarry and average particle size of muckpile after each shot were assessed by digital image analysis method. Bucket loading times have been measured by stopwatch study after five shots. Excavator bucket loading times were also estimated by bucket loading time estimation formula which was published in ISEE 2007 Conference, Ozdemir et al. 2007. Estimated and measured times have been statistically analyzed and the accuracy rate of formula has been determined for five events.

Jan 1, 2008

By H. K. Lin

The effect of metallic iron fines on froth flotation of a sulfide ore was examined by comparing the flotation results with and without iron fines present in the flotation feed. Mild steel and ceramic laboratory ball mills were used to grind 600 g sulfide ore charges. The mild steel ball mill generated approximately 4.6 g of iron fines (0.8% of the ore charge mass) when grinding to a product size of 80% passing 200 mesh (75 mm). When a low dosage of a weak xanthate collector was used in flotation, the impact of the iron fines on sulfide flotation was marked. Higher dosages of stronger xanthate collectors rendered the impact of the iron fines much less significant. Consumption of the collectors by the powdery iron fines is believed to cause the differences observed in the flotation results. A galvanic effect on flotation was not evident in this study. The impact of the iron fines on silicates depression was also examined.

Jan 1, 2008

By James W. Marold

Tunnel and shaft plugs have been designed to assist in construction of new and rehabilitation of existing tunnels and shafts. Tunnel plugs have been used to provide construction access for side by side tunnels, separation of raw and treated water, and to allow operation of one tunnel during construction of a nearby tunnel. Shaft plugs have been used to seal up surface openings to tunnels and to prevent seepage of water to the surface through adjacent tunnels or shafts. The design construction details of tunnel and shaft plugs are provided. Typical examples of tunnel and shaft plugs are provided.

Jan 1, 2008

By Jerry Pyatt

Lead has been used by mankind since before the Egyptian pyramids were built. Its durability provides for a continuum of innovation. As the largest integrated lead producer in the Western Hemisphere, The Doe Run Co. is committed to locating, mining, processing and sup-plying lead in ways that are responsible and sustainable. It takes ingenuity and resolve to successfully operate in the heavy industry field today. Doe Run is committed to applying responsibility through sustainability, lean manufacturing, safety, environmental stewardship, education and workforce development, and com-munity support.

Jan 1, 2008