Search Documents

By A. Fahimifar, H. Soroush

Abstract: Triaxial tests were conducted on the schist specimens with various anisotropic angles under confining pressures of 0, 7 and 15 MPa, and axial stress-axial strains, were measured and plotted for various conditions. The results obtained reveal the effects of schistose on the strength and deformability of the rock very clearly. Peak strength of the specimens for 00 and 900 schistose orientations are nearly the same. Modulus of elasticity of this rock varies with anisotropic angle. For 0 orientation modulus of elasticity increases to a maximum. Confining pressure increases the peak strength and improves the rock deformability. However, this effect is not the same for various orientations, and there are no similar trends for each anisotropy direction. Analysis of the results shows that consideration of a linear failure criterion such as Mohr-Coulomb is appropriate for the prediction of rock behaviour up to 10 MPa, rather than a non-linear one. The analysis also reveals that the friction angle and cohesion are affected by the anisotropy orientation, and this effect is more important for the cohesion than the friction angles. Resume: Les esseys triaxiales sur les echantillon d un roch schist avec les differents angles non-isotrop sous les tension lateral zero et sept et qoinze mega pascal (mpa) est fait et les covtraite et allongment unitaire sont mesure et leur curues est destine sous different condition les resultats obtenues montre les effets du schistosite sur le resistance et le ductilite vissiblement. Le resistance final sur les echantilions pour les angles o degre et 90 degree est equivalent. Le modoule d elasticite de ce roch sera difere par a port de l angle de stratification. Pour l angle o degree le valeur de modoule est le maximum. le pousse lateral augmenterai le resitance final, et sera amilterai le toleran le de ductilite. Mais cette effet bn est pas unigue pour les different stratification, et pour les diferents directions no– isotrop it n y a pas le meme solution. L analyse des resulitats montre que le criterre de ruin comme mohr–colomb est moderate pour le pousse lateral jusq av lo mega pascal , et ce n est pas neccesaire d utiliser de criterre no–linear . Cette analyse aussi montre que l angle de frottement et cohsion est en relation de la direction no–isotrop, et cette effet est olus important pour le cohsion par a port de l angle de frottement . Abriß : Dreiachsige Prüfung wurde auf den schist Exemplaren mit verschiedenen anisotropic Winkeln unter Bestätigen von Drücken von 0.7 und 15 MPa geleitet, und axiale Spannung axiale Spannungen, wurden gemessen und für verschiedene Bedingungen wurde geplant. Die Ergebnisse haben die Wirkungen von schisocity auf der Kraft und dem deformability des Felsen sehr deutlich erhalten offenbart. Maximale Kraft der Exemplare für 0° und 90 sind° schistos Orientierungen beinahe das gleiche. Modulus der Elastizität von diesem Felsen ändert sich mit anisotropic Winkel. Für 0° vermehrt Orientierung modulus der Elastizität zu einem Maximum. Einschränkender Druck vermehrt die maximale Kraft und verbessert den Felsen deformability. Aber ist diese Wirkung nicht das gleiche für verschiedene Orientierungen, und es gibt keine ähnlichen Tendenzen für jede anisotropic Richtung. Analyse der Ergebnisse zeigt jener Überlegung Kriterium eines linearen Ausfalls wie zum Beispiel Mohr Coulomb passend für die Voraussage von Felsen Verhalten bis zu 10 MPa, anstatt eines nicht linear ist. Die Analyse offenbart auch, daß der Reibung Winkel und Bindekraft werden beeinflußt von der anisotropic Orientierung, und diese Wirkung wichtiger für die Bindekraft ist, als der Reibung Winkel

Jan 1, 2003

By D. Grabowski, Z. Pokryszka

ABSTRACT: Some residential areas of the iron basin of Lorraine (in the North-East of France) are affected by noxious gas emissions (under oxygenated, carbon dioxide loaded and radon loaded gas mixtures). Site investigations showed that the gas flow was mainly due to natural thermal air circulation between old mines and the external atmosphere. The main hazards associated with this flow of gas and its potential accumulation in confined volumes within buildings are asphyxiation and intoxication. A further study is in progress in order to better understand the origin of the gas generation within the old iron mine workings. Following the first hypothesis, the carbon dioxide emission is mainly due to the specific hydro-geo-chemical process associating the pyrite oxidation with the acid dissolution of carbonates. KEY-WORDS : gas, emission, mine, flow, pyrite. ZUSAMMENFASSUNG: Einige Wohngebiete der Eisenmulde Lothringen (im Nordöst Frankreich) werden von Ausgasung gesundsheitsschädlichen sauerstoffarmen Mischungen, die mit Kohlendioxid und Radon beladen sind, betroffen. Untersuchungen am Ort haben gezeigt, wie diese Gasstroemung von natürlichem thermischen Luftumlauf zwischen den alten Bergwerken und der externen Atmosphäre ausgelöst wird. Erstickung und Vergiftung sind die wichtigste Risiken, die mit dieser Gasströmung und ihrer möglichen Speicherung in begrenzten Lokalen zusammenhängen. Eine weitere Untersuchung wird durchgefuehrt so dass man die Herkunft der Gaserzeugung in den alten Grubenräume besser versteht. Der ersten Hypothese folgend, Ausgasung von Kohlensäure liegt vor allem an dem hydro-geo-chemischen Prozess, der Pyritrösten mit der säuren Auflösung von Karbonate verbindet SCHLÜSSELWÖRTER: Gas, Ausgasung, Bergwerk, Strömung, Pyrit RESUME: Certaines agglomérations du bassin ferrifère lorrain (au Nord-Est de la France) sont affectées par des émanations de mélanges gazeux sous-oxygénés et chargés en certains gaz nocifs (dioxyde de carbone, radon…). Les investigations effectuées in situ ont montré que les écoulements gazeux à l’origine de ces émanations sont liées au phénomène de tirage naturel entre les anciens travaux miniers et la surface. Les principaux risques engendrés par ces émanations de gaz et son accumulation possible dans des endroits confinés sont l’asphyxie et l’intoxication. Une étude est en cours afin d’expliquer l’origine de la modification de l’air au sein des vieux travaux miniers. Les émissions de dioxyde de carbone seraient dues à des processus hydro-geo-chimiques associant l’oxydation de la pyrite et la dissolution de carbonates. MOTS CLES: gaz, émanation, mine, écoulement, pyrite.

Jan 1, 2003

By Adrian Moore, John Wilson, Alan Richards, Emad Gad

Project C9040 – ‘Structure Response to Blast Vibration’, funded by the Australian Coal Association Research Program (ACARP), involved the investigation of the structural response from blast vibration of three houses of brick veneer construction subject to a wide range of ground vibration levels. This paper summarises the findings of a house subject to vibration levels up to 220 mm/s (8.7 in/s). Damage attributable to blast vibration was not observed until vibration levels exceeded 70 mm/s (2.8 in/s).

Jan 1, 2003

By Robert E. Mazurak

Mines and plants for sale, downsizing, bankruptcies, consolidation, slab imports, minimill growth displacing traditional integrated steel-making. These are some issues for North American iron ore and integrated steel producers. But the blast furnace still remains the workhorse of the ironmaking industry. And direct reduction and other alternate ironmaking technologies have yet to make any serious inroads in North America. How come? This article addresses the current state of primary ironmaking in the changing North American steel industry, the direct reduction market and new technologies under development that may hold some promise.

Jan 1, 2003

By F. T. Cawood

This research report was produced in response to the release of the Mineral and Petroleum Royalty Bill. It involved are view of the mineral investment environments of selected countries in order to form an opinion on the appropriateness and competitiveness of the proposed royalty structure for South Africa. Many emerging countries have recently attracted a significant share of foreign investment, as a direct result of changes in policy. These are, by implication, the least risky and most favourable destinations for the ?investment dollar?. The five most competitive countries, namely Chile, Argentina, Peru, Mexico and Brazil have been identified as succeeding with their policy visions of creating favourable domestic investment environments. The investment rules of these countries served as a basis for the compilation of a Competitive Investment Framework (CIF). This is a template of best practice against which other investment environments, such as that of South Africa, can be measured. The framework indicates that mineral royalties should ideally be no more than three per cent, demonstrating that the regime proposed in the Royalty Bill is out of step with international best practice. Mineral royalties can never be viewed in isolation and in the assessment of the rates proposed in the Royalty Bill, one must consider the total taxation package. Such assessment appears in Section 5 of this report, demonstrating that there is reason for concern if National Treasury were to impose the rates stipulated in the Royalty Bill. The alternatives, conclusion and recommendations of the review appear in Sections 9 and 10. These are the result of independent analysis and assessment of the fundamental principles. It is done through the application of a Competitive Investment Framework that avoids the highly subjective and emotional views that often accompany a process like this.

Jan 1, 2003

By Neil F. Archer

Due to the increased chance of violations and shutdowns by the U.S Occupational Safety and Health Administration(OSHA) and the U.S. Environmental Protection Agency (EPA), a company can save itself problems by taking control of the dust caused by conveying material. A complete dust-control policy can keep these emissions confined, sealed and suppressed, protecting the environment from fugitive, airborne dust. Material handling and processing, storage and traffic are the major dust producing sources. All industries that convey dry, light material need a dust control system.

Jan 1, 2003

By J Hadjigeorgiou

Underground mines often rely on ore pass systems to ensure the transport of ore and waste. Consequently, it is important to ensure the smooth operation of such systems. Ore pass degradation that may require rehabilitation results in production delays and high operational costs. The occurrence of hang-ups within an ore pass also leads to disruption of ore production. There are important safety concerns when worker intervention is necessary to re-establish material flow in the ore pass. In order to facilitate the design of ore pass systems, mining operations often rely on past experience, or semi empirical guidelines. This paper describes recent efforts to establish a comprehensive database on current practices; encountered operational problems and solutions in ore pass design in Quebec underground mines.

Jan 1, 2003

By T. R. Roy

"This paper presents an objective model for the estimation of fire risk potential of an underground coal mine panel by the bord-and-pillar method of mining where extraction is carried out by depillaring with caving. The fire risk rating procedure for the estimation of fire risk potential involved in the panel is described in detail. The model developed thereof is tested with the field data collected from different collieries across the country along with the laboratory data for critical assessment of fitness of the model. Some results showing the validity of the model are also cited here. Introduction The occurrence of fire in underground coal mine panels is quite common in India and elsewhere. These fires cause extensive loss of resources.Although substantial work has already been done by different research organizations, the problem has not been fully eliminated.The causes of panel fires depend not only on the spontaneous heating susceptibility of coal, but also on the extraneous conditions created in the panel due to the mining operations. From the studies done so far by various organizations, it is apparent that two types of parameters associated with spontaneous heating of a coal mine panel exist: intrinsic and extrinsic. Parameters related to the nature of coal, i.e., its physicochemical characteristics, petrographic distribution and mineral make-up are intrinsic, while the extrinsic parameters are related to the atmospheric, geological and mining conditions such as scope of leakage of air into the panel, wetness of mines, heat dissipation capacity of the panel, gassiness of seam, geological disturbances, method of extraction, size of panel, etc.Banerjee (1982) identified twenty-two mine parameters such as spontaneous heating susceptibility of coal, method of mining, geological disturbances, quality of overburden, degree of consolidation of coal mass, scope of accumulation of coal fines, etc. that can influence spontaneous heating in underground mines. He used the terms “high” and “low” for fire risk rating of each of these parameters. Since this approach is oversimplified, it can not determine the exact fire risk potential of an underground working."

Jan 1, 2003

By J. L. Fuentes-Cantillana, Á. Rodríguez, P. Morillo

Evacuation operations from work places in the case of an emergency are the key to minimising the effects of catastrophic type accidents such as fires, explosions, cave-ins, floods, etc. The correct planning of these operations, having the necessary means for sounding alarms and communicating and suitable training of personnel are the key factors for guaranteeing successful evacuation. The article gives an analysis of the problem in the case of subterranean mining and various types of work developed by AITEMIN in this field, including the development of new alarm and communication means specially adapted to the characteristics of mining operations, development of tools for help in the preparation of emergency plans and experiences in the education and training of personnel.

Jan 1, 2003

By A. Rejeb

ABSTRACT: This paper contributes to the study of underground structures in argillaceous media, especially Tournemire argillites (Aveyron, France). The basic results obtained over six years in two experimental drifts at the Tournemire site are presented. In situ measurements cover drift wall temperature, humidity and convergence. Delayed convergence represents around 50-65% of the total measured convergence. Analysis of the measurements has shown that delayed convergence is explained by the viscoplastic behaviour of the argillaceous formations. Lemaitre’s rheological model has been extended to the orthotropic case, as Tournemire argillite is naturally anisotropic. The triaxial creep test results on samples at different orientations enabled the parameters of the Tournemire argillite to be identified in terms of orthotropic viscoplastic law. A plane deformation model, using this rheological law and the initial stress field in the site, was developed to interpret the convergence measurements in the drifts. The computed results match the measurements well, especially during the excavation phase. KEY WORDS: Argillite, convergence, time-dependent behaviour, creep, viscoplasticity, modelling. ZUSAMMENFASSUNG: Der vorliegende Artikel ist ein Beitrag zur Untersuchung der unterirdischen Strukturen tonhaltiger Milieus, insbesondere der Tongesteine von Tournemire (Aveyron, Frankreich). Die wichtigsten Ergebnisse, die in zwei Forschungsstrecken am Standort Tournemine über einen Beobachtungszeitraum von sechs Jahren zusammengetragen wurden, werden hier vorgestellt. Gemessen wurden in situ Temperatur, Feuchtigkeit und Streckenkonvergenz. Von der insgesamt gemessenen Konvergenz sind etwa 50 bis 65 % auf zeitlich verzögerte Konvergenz zurückzuführen. Die Auswertung aller Messungen hat ergeben, dass die zeitverzögerte Konvergenz mit dem viskos-plastischen Verhalten des Tonsteinmassivs zu erklären ist. Aufgrund der naturgemäßen Anisotropie des Tongesteins von Tournemine wurde das rheologische Modell von Lemaitre auf den orthotropen Fall ausgedehnt. Triaxiale Kriechversuche bei jeweils unterschiedlicher Ausrichtung dienten der Ermittlung der einzelnen Parameter des orthotropen, viskos-plastischen Gesetzes. Zur Auswertung der Konvergenzmessungen innerhalb der beiden Strecken wurde unter Beachtung dieses rheologischen Modells sowie des ursprünglichen Spannungszustands vor Ort ein flächiges Deformationsmodell entwickelt. Die Rechenergebnisse zeigen eine gute Übereinstimmung mit den Messungen, insbesondere während der Vortriebsphase. SCHLÜSSELWÖRTER: Tongestein, Konvergenz, zeitlich verzögertes Verhalten, Kriechen, Viskoplastizität, Modellbildung. RESUME : Cet article est une contribution à l’étude des structures souterraines dans les milieux argileux, notamment les argilites de Tournemire (Aveyron, France). Les principaux résultats obtenus pendant six années, dans deux galeries d’expérimentation au site de Tournemire, sont présentés. Ces mesures portent sur la température, l’humidité et la convergence des parements des galeries. La convergence différée représente environ 50 à 65% de la convergence totale mesurée. L’analyse de l’ensemble des mesures a montré que la convergence différée est interprétée par le comportement viscoplastique du massif argileux. Etant donné que l’argilite de Tournemire est naturellement anisotrope, le modèle rhéologique de Lemaitre a été étendu au cas orthotrope. Les résultats des essais de fluage triaxial, sur des échantillons à différentes orientations, ont permis de déterminer les paramètres de la loi viscoplastique orthotrope. Un modèle en déformation plane, utilisant cette loi rhéologique et l’état de contrainte initiale dans le site, a été développé en vue d’interpréter les mesures de convergence dans les galeries. Les résultats des calculs sont en bon accord avec les mesures et plus particulièrement durant la phase de creusement. MOTS-CLEFS : argilite, convergence, comportement différé, fluage, viscoplasticité, modélisation.

Jan 1, 2003

By Harry Parker

Resource and Reserve Audits Becoming Increasingly Common Types of Audits -Review of Methodology (‘Fatal Flaw’) -Due Diligence – (‘Sign Off’) -Endorsement – (‘QA-QC’) Suggested Standards in Red

Jan 1, 2003

By Ch. Schroeder, F. Collin, R. Charlier, Y. J. Cui

The paper proposes two numerical models ot the mechanical behaviour of chalk. First, an elasto-plastic constitutive law reproduces the different plastic mechanisms of the chalk and the influence of pore fluids by introducing the concept of suction. Secondly, a model able to reproduce time dependence behaviour. Eventually, the paper gives a simulation of an academic reservoir during depletion and waterflooding phase. Der Artikel stellt zwei numerische Modelle des mechanischen Verhaltens der Kreide vor. Das erste ist ein elasto-plastisches Modell, das verschiedene plastische Mechanismen der Kreide und den Einfluss von Porenflüssigkeit, unter dem Begriff der Suktion, reproduziert. Das zweite Modell berücksichtigt darüberhinaus das zeitabhängige Verhalten. Schliesslich zeigt die Veröffentlichung eine Simulation einer theoretischen Lagerstätte während der Entleerung und der Wasserinjektion. L'article propose deux modèles numériques du comportement mécanique de la craie. Le premier est une loi élasto-plastique qui reproduit les différents mécanismes plastiques de la craie et l'influence du fluide interstitiel par l'introduction de la notion de succion. Le second est un modèle prenant en compte les effets différés. Enfin, l'article présente une simulation d'un réservoir académique durant les phases de déplétion et d'injection d'eau.

Jan 1, 2003

By Jhon Cuya

Titanium dioxide is the well-known catalyst for the photodecomposition of water in UV region and its nanoparticles show better performance than its bulk materials. Furthermore, partially sulfurized TiO2 is expected to be chemically stable and have an enhanced photocatalytic activity compared with TiO2. For this purpose, the sulfurization behavior of TiO2 nanoparticles was thermogravimetically (TG) studied by a thermo-balance with a quartz spring using CS2. From the TG curve of TiO2 nanoparticles, first, the weight decrease appeared down to around 8 wt% and then sulfurization reaction started at around 500 °C at heating rate of 1O 'Cumin. The weight increase curve showed a maximum of ca 30 wt% at around 750 T and then gradually decreased to ca 12w% at 1000OC. This would be caused by the formation of TiS2 followed by the decomposition of TiS2 to lower sulfides, such as Til.08S2 and Ti3S4. From the comparison of the sulfurization of TiO2 nanpparticles with that of anatase, rutile and Ti(OH)4, it was found that TiO2 nanoparticles showed a similar behavior to that of Ti(OH)4.

Jan 1, 2003

By B. Solar Menéndez, M. B. Díaz Aguado, I. Á. Fernández, C. González Nicieza

The analysis of subsidence due to the opening of an underground void (mining, water exploitation or civil works hole) is a problem usually hard to solve. First of all, it requires a predictive model, in order to define both the displacement magnitude and area affected by subsidence. Such model should be validated with measurements of the actual movements sustained on the surface, in order to adjust it properly and enable influence of future behaviour in a reliable way. Two different kinds of problems might arise. On one side, it is necessary to control and measure surface movements in a very exhaustive way during a long period of time, beginning before underground works take place and finishing years after they are over. Furthermore, three factors bring in errors, some times of magnitudes higher than the displacement magnitudes measured. These include: the fact that reliable and long-term information cannot always be achieved; the precision of measuring devices; and the design of the topographical network itself. In addition, the predictive models more widely used only apply to certain excavation geometries, mainly to horizontal holes. In light of this background, the Group of Rock Engineering, of the University of Oviedo Mining Department, has developed a working methodology and a specific software tool, Subsidence 3D, to estimate ground displacements and strains. The program will allow for predictive models to be defined and also allows the treatment of data related with topographical marks and its comparative analysis with calculated results. The software has been programmed using Visual C++. Graphical outputs however are generated using AutoCAD 2000. This paper mainly refers to a practical situation, an underground coalmine, remarking the main difficulties arisen during the study of the available information and proposing how to solve them. A predictive model in subsidence 3D was established and validated. The actual behaviour of the ground was that in the model.

Jan 1, 2003

By J. F. Shao, G. Duveau, W. Z. Chen, O. Ozanam

In this paper, we present a sensitivity study for the numerical modelling of hydromechanical coupling around a shaft in partially saturated claystone. Two representative constitutive models have been used: an elastoplastic damage model (IDEPLML) and an elastic perfect plastic model based on the Hoek and Brown failure criterion (H&B). A series of comparative studies have been performed with respect to main parameters involved in coupling process (mechanical, hydraulic and hydric properties). The emphasis is put on the evaluation of induced plastic, damaged and failed zone due to excavation and drying process. Dans ce papier, nous présentons une étude numérique paramétrique du comportement hydromécanique couplé d’une argilite partiellement saturé, lors du creusement et de la maintenance d’un puit L’étude paramétrique porte à la fois sur le type de modèle et sur les principaux paramètres (mécaniques hydrauliques et hydriques) intervenant dans le couplage. L’accent est principalement porté sur l’évaluation des zones plastifiées autour de l’ouvrage lors de la désaturation. In unserem Beitrag geht es um eine digitale parametrische Untersuchung über das hydromechanische Verhalten eines teilweise durchtränkten Tons beim Abteufen und dem Betrieb von Schächten. Die parametrische Analyse konzentriert sich auf den Modelltypus und auf die wesentlichen bei der Verbindung wirksamen Parameter, d.h. die mechanischen, hydraulischen und hydrologischen. Der Schwerpunkt liegt auf der Bewährung der plastifizierten Bereiche des Bauwerkes während der Austrocknung.

Jan 1, 2003

By R. Armstrong, C. Ware, P. Sudan, G. Whitmore

The northern KwaZulu-Natal (KZN) coastal dune cordon, South Africa, extends from north of Durban into Mozambique. The Quaternary dune cordon, which can be up to 2 km wide, comprises a series of stacked, unconsolidated dunes that in places attain a height of over 100 m. Mining of the dunes produces much of the world’s supply of ilmenite, rutile and zircon. This paper documents the age of zircon grains separated from dune units, identifies likely source rocks and presents an evolutionary history for the dune cordon. Between 30 and 60 detrital zircon grains from three distinct units from the northern KZN coastal dunes were analysed for U/Pb isotopic ages using the SHRIMP II at the Australian National University. The samples represent units from the base (ca. 250 ka; luminescence age1),middle (ca. 190 ka2) and upper (ca. 20 ka2) portions of the coastal dune cordon. Zircon grain ages identify three source populations: (1) a 1 000 to 1 200 Ma group correlated to the Natal Metamorphic Province, (2) a 500 to 650 Ma group representing a Pan-African belt, which may correlate to the Mozambique Belt and (3) a ca. 650 to 800 Ma group of unknown provenance. Surprisingly, the presently exposed basement, comprising the Kaapvaal Craton and Archaean volcano-sedimentary sequences, has not supplied a significant amount of zircon grains (< 5%).This suggests that unroofing of basement rocks in the region has only occurred during the last 20ka. In addition, the absence of zircon grains younger than 500 Ma indicates that the bulk of zirconis not reworked from the Karoo Supergroup cover succession, but may be sourced by reworking of the Natal Group sandstones.

Jan 1, 2003

By Jerry C. Tien

Changes and the pace of change in China’s coal industry have been extraordinary during the past several years. At least 35 of the 94 former coal bureaus have been restructured into different mining companies and groups. Some of the more productive and efficient ones were further strengthened through consolidation and expansions. And several have even formed, or are in the process of forming, strategic alliances with utility companies, railroads, ports and chemical companies to secure additional reserves and coal sales. In addition, the improvement in coal pricing during the past two years has enabled China’s coal industry to move ahead with some needed changes. Coal mining accidents, though, remain a major concern for the Chinese government. Accidents remain high even though the government has made efforts to shutdown more than 55,000 unlicensed, unsafe small coal operations throughout the country.

Jan 1, 2003

By Marco D. Boscardin

Control and mitigation of building response to construction activities are assuming a greater role in design decisions for underground construction. Alternatives for controlling building response have multiplied with the continued development of ground modification methods, better control of construction activities that cause ground movements, and increased understanding of building behavior and response. This paper describes approaches to estimating building response to construction-related ground displacements caused by adjacent excavation and highlights the discussion with several case history examples. Examples discussed includes experiences with two, seven-story historic structures, supported by timber piles with granite block pile caps, which were underpinned in preparation for ground-freezing ground stabilization and tunnel construction beneath the buildings. The elevation of each building column was monitored and elevation adjustments were actively performed during construction. The second example examines the performance of a slurry wall braced cut, 45 to 50 feet deep penetrating through a stiff crust into a soft clay layer and associated building response. This cut was immediately adjacent to two, approximately 15-story office buildings, which were supported by deep foundations founded in the stiff crust.

Jan 1, 2003

By M. Q. W. Jones

This paper summarizes important features of a compilation of thermal properties of stratified rocks from Witwatersrand gold mining areas. The database consists of more than 1000 thermal conductivity measurements, more than 700 density measurements, and nearly 100 heat capacity measurements. Most important rock types and stratigraphic units are well represented. Heat capacity does not differ significantly from one rock type to another, and density is relatively uniform although particular rock types are characterized by distinct average values. Different rock types also have distinct thermal conductivities, but this parameter varies by a factor of four to five. Primary factors controlling the thermal properties are mineral composition, degree of metamorphism, and porosity. In addition, the temperature dependence of thermal conductivity and heat capacity of quartzite may significantly decrease the thermal diffusivity of this rock at deep mining levels.

Jan 1, 2003

By Dale Preece, Stephen Chung, Qian Liu

Stoping is one of the widely adapted methods in underground mining. In this method, fanned or parallel holes are often drilled from a top sill down to a sub- level in the ore zone and blasted ring by ring into a stope for excavation. At Brunswick Mine of Canada, this technique has been used daily in conducting production blasts. However, when mining into the West Ore Zone, it has been identified strategically that a mass stope blast, involving the blasting of rock from the 3-sub level down to the 1-sub level, should be considered to ensure the safe operation and regaining of access to the trapped main ore zone. The challenge of this mass blast lies in the control of ground vibration and precise timing for blasting 800 holes drilled in six blocks from three different levels within 6.5 seconds, to allow sufficient void to be created in each level for the muck moving in order from the upper to the lower levels without bridging. This paper describes stope blast simulations using a discrete element computer code for modeling blast-induced rock displacement in conjunction with a precision electronic programmable delay timing system for various stope geometries including a drop raise blast at the start of the mass blast. The modeling concept is also described in the paper.

Jan 1, 2003