Search Documents

By Hans Perlid

In the handling of emulsion explosives pumping is a key operation. A number of serious accidents has shown that pumping can be a risky operation and should be carefully considered and investigated. This is the background behind a series of pump tests carried out by NITRO NOBEL.

Jan 1, 1996

The West Coast region of the South Island is situated astride the Pacific û Australian plate boundary zone. The most significant component of this zone is the Alpine Fault. A variety of reconstructions of the pre-Alpine Fault plate tectonic configuration of the New Zealand continental area have been attempted over the past 25 years or so. Most of these have not been closely constrained by a regional compilation of field data related to the age and horizontal displacement history of the Alpine Fault. A model in which the Alpine Fault was initiated no earlier than the interval 18 - 16.5 Ma (B.P.) is proposed, a significantly younger age of inception than has been widely accepted as the onset of dextral displacement along the plate boundary through the South Island. A subsequent history of displacement is presented consistent with the West Coast basin stratigraphy. The alluvial gold content of some parts of the Miocene to Pleistocene conglomerate sequences is also discussed.

Jan 1, 1996

By E. J. Debicki

"At the 1992 PDAC Convention, Norman Keevil announced the formation of the Exploration Technology Division (ETD) of the Mining Industry Technology Council of Canada (MITEC). It was evident that base metal reserves in Canada were declining and that the cost of discovering a deposit in Canada was increasing. Coordinated research to develop new exploration technologies was required to discover the next generation of ore-bodies. The ETD was formed in response.The mission of the ETD is to contribute to the survival, profit, and growth of the Canadian mining industry by improving the efficiency and effectiveness of mineral exploration through development of innovative technology by man-aging and coordinating applied cooperative research. In addition, it is the intent of the ETD to become the principal agency by which cooperative research funds are transferred to researchers from the mining industry. The division is industry driven, industry funded and industry managed.The ETD’s Three-Year Plan has focussed80% of its research funds toward two objectives, improving the efficiency of exploration for VMS deposits and establishing the parameters necessary to discover the next Hemlo deposit. The remaining 20% is allocated to other projects, with the current emphasis on geophysics.In 1995, corporate members total twenty-three major mining companies accounting for90% of the exploration expenditures in Canada. The ETD is currently managing ten cooperative research projects totalling $4.6million. Other projects, estimated at $1.6 mil-lion, are currently under development."

Jan 1, 1996

By F. E. Chase

Mobile roof supports are shield-type support units mounted on crawler tracks. Mobile roof support (MRS) units are used during retreat mining, and they eliminate the setting of roadway, turn, and crosscut breaker posts which are required during pillar recovery operations. Mobiles are a more effective ground support than timbers, and their usage enhance the safety of section personnel and reduces material handling injuries. MRS usage is rapidly increasing, and approximately 40 U.S. coal mines have successfully employed this relatively new technology. This paper is in response to increasing requests from operators, State and Federal Regulatory Agencies, and others on the practical aspects of MRS usage in underground coal mines. During this investigation, nearly half of the U.S. mines which have utilized mobiles were visited. This report depicts the more common pillar extraction methods which operators have found successful. The Christmas tree and outside lift methods are illustrated and discussed. Roof control plans that do not require breaker posts or allow pillar extraction with fewer than four mobiles are also examined. In addition, operators' experiences with setting pressures, loads, and rates of loading during pillar extraction are addressed. Mining and support strategies to more effectively control hillseams, weak roof, and gob overrides which have entrapped equipment are also discussed.

Jan 1, 1996

Seam correlation in the central Rapahoe Sector (Greymouth Coalfield) can be enhanced by detailed lithostratigraphy and chronostratigraphy. Rewanui Coal Measures are overlain comformably by lacustrine, deltaic and fluvial strata, and this upper contact can be located using lithological and geophysical log character. The Cretaceous-Tertiary Boundary (KTB) occurs near the top of Rewanui Coal Measures and has been identified palynologically in 16 drillholes. The Rapahoe Sector can be subdivided into two palynostratigraphic domains which adjoin along a basement normal fault which was downthrown to the north during coal measure deposition. The KTB provides an isochronous surface which is independent of the lithostratigraphic datum. Using the KTB as a datum, the æUpperÆ, æMainÆ and æSubmainÆ seams can be reliably correlated throughout the southern and central Rapahoe Sector. Similarly, the æSubmainÆ seam can be correlated with æcÆ seam of the Strongman Mine area, though other Strongman seams are absent from the central and southern Rapahoe Sector.

Jan 1, 1996

By Steven G. Vick

Effects of the August 1995 failure of the Omai tailings dam in Guyana continue to be felt throughout the mining industry. This article is taken from the final report of the independent body of experts commissioned by the government of Guyana to establish the cause of the failure. It explains what happened, why and how to avoid it in the future. Despite environmental, health and safety effects that were negligible by any objective measure, the failure has received wide international attention. Coming on the heels of the shift in exploration targets and development opportunities to developing countries, it has intensified interest in tailings dam safety and environmental management issues. An informed understanding of the nature of the failure and its effects is key to responding to these concerns.

Jan 1, 1996

By Steve Thoman

After the 1989 Loma Prieta Earthquake, the California Department of Transportation (Caltrans) initiated an overview of the Caltrans Bridge Design Specifications (BDS) and bridge seismic design practice in California. This overview is continuing under the direction of the Applied Technologies Council (ATC-32), to review and revise as necessary existing standards, performance criteria, specifications, and practices for design and construction of new bridge structures within California. The ATC-32 project began in August 1991 and is expected to be completed in 1995. Since 1990, Caltrans project-specific seismic criteria have been developed and implemented on the I-280 and I-480 projects in San Francisco. Caltrans and an independent seismic safety review panel continue to develop and implement these criteria on other projects. In 1991 and 1992, project-specific seismic criteria were used on the I-880 reconstruction project in Oakland. The seismic safety review panel considered the I-880 seismic design criteria a state-of-the-art methodology to ensure seismic safety against collapse of bridge structures subjected to a maximum credible seismic event. This paper highlights the 1992 "I-880 Reconstruction Project Seismic Design Criteria Review" report prepared by the Seismic Safety Review Panel and Caltrans Division of Structures and will compare pre-1989 BDS and AASHTO methodologies to the I-880 criteria.

Jan 1, 1996

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996

By Jennifer Riefenberg

Ground control hazards, coal quality, ore reserve estimation, and pollution modeling seem unrelated topics from most mining perspectives. However, geostatistical methods can be used to characterize each of these, and more topics. Exploratory drill core data, and continued drilling and field measurements, can provide a wealth of information related to each of the above areas and are often severely underutilized. Recent studies have led to the development of the Multiple Parameter Mapping (MPM) technology, which utilizes geostatistics and other numerical modeling methods, to generate a "hazard index" map, often from exploratory drill core data. This mapping has been presented for ground control hazards relating roof quality, floor quality, numerically modelled stresses due to mining geometry, and geologic features. A review of the MPM method, future directions with the MPM, and a discussion of using these and other geostatistical methods to quantify coal quality, ore reserve estimation, and pollutant modeling are presented in this paper.

Jan 1, 1996

By D. R. Gehring

Effective project management is an excellent technique for meeting a goal through set, well-defined objectives. Even though project management is successfully used throughout the world in various construction projects, underground mining has unique characteristics that require approaches that vary from classical project management theory. Typically, a project includes four main stages: definition, planning, implementation and control. Definition and planning are often the most overlooked stages, but are arguably the most important. This paper addresses practical techniques for the definition and planning of projects for underground construction.

Jan 1, 1996

Studies of the Main Seam in the Rapahoe Sector of Greymouth Coalfield have shown that the proportions of palynomorphs and palynomorph groups vary vertically within the seam, but remain laterally consistent. Subsequent examinations of other seams in the Rapahoe Sector have demonstrated that the changes in palynomorph proportions observed in the Main Seam are specific to that seam, effectively providing a seam 'fingerprint'. Such a characteristic signature may be used to identify the Main Seam where faulting or seam splitting confuses seam correlation between drillhole intersections. Palynomorph assemblages are derived from the original plants which formed the peat mire, and yield information on mire conditions such as climate, mineral matter input and chemistry. These depositional factors influence coal properties such as mineral content, volatile matter yields and coal breakability. Palynological data can therefore assist in development of depositional lTIodels for prediction of coal quality variations. Several other, thiner seams in the Rapahoe Sector have been demonstrated to also contain recognisable palynomorph assemblages, suggesting that other seams may also possess distinct palynomorph abundance profiles.

Jan 1, 1996

By V. Eu. Anufriev

Despite of significant cost advantages and the positive expierence roof bolting is limited up to 15-20% of all workings at the Cuzbass mines. The low level of application of the technology is the result of specific mining and geological conditions and defects of organization and technical support. When analysing mining and geological conditions of development working maintenance and geomechanical aspects the necessity of changing of technological schemes of preparation and extraction of mine sections is obvious. The prospects of large-scaled transferring from frame support to roof bolting are connected with introduction the technology of support with the help of non- expanding bolt classes including bolts with mineral filler fixation. The design of bolters with mineral filler fixation is given here. The results of testing of bolt load characteristics in artificial holes and in situ are proved the technology efficient. For increasing of drilling works efficiency it is necessary to master the production of oilless compressor and heading machines with the manipulator. For bolt dimension forecast it is recommended to use the relations of measured parameters of "dome" to roof shifts. Effective monitoring of rock pressure in the junctions is connected with the use of support of conventional bolts together with bolts of deep installation with simultaneous supporting of face ends with special mechanical sets, which compensate face length change.

Jan 1, 1996

By B. Ramanathan

The results of a pile load test on a 1200 mm dia and 25 m long bored Cast-in-situ pile in soft rock is reported. The subsoil has a high N value of above 60 from 7 m to 21 m. The soft rock was observed below 21 m and N value exceeded 100. The theoretical calculations showed that the safe carrying capacity will be about 410 t. But the actual load test on the pile indicated that the allowable load is only about 140 t. This is attributed to the fact that the soil is cemented and loses strength due to remoulding caused by pile installation. It is concluded that great care should be exercised in determining the carrying capacity of piles in cemented soils and soft rocks and that 'N' value alone should not be used.

Jan 1, 1996

By Jacque Trottier, Marcel Vallée, Gratien Gélinas

"Mineral exploration in Canada traditionally has gone from boom to bust in cyclical pat-terns following market and discovery cycles, but other endemic factors related to exploration financing and performance have contributed to the amplitude and recurrence of these fluctuations. In view of these problems, junior exploration is reviewed here in a marketing perspective, looking at the 4 Ps: Product, Price, Placement and Promotion.In the 1980s, MEDA incentives gave the shares of junior and mining companies significant price and promotion advantages, and contributed to excessive exploration funding. Many were thus led to minimize the basic values needed for continued investor interest: appropriate levels of product quality, sustained share value and customer satisfaction. Basic changes are needed to improve the marketing of junior mineral exploration in the future, with or without improved fiscal incentives. To be successful, the required improvements must come from the technical participants, but the financial partners also need to be involved.Exploration in Canada must be marketed with vigour, both in Canada and internationally. Exploration, mine development and mine production are essential to our economy. They are environmentally acceptable and they are welcome in Quebec and in most Canadian provinces and territories. Canadian exploration and mining are entrepreneurial industries that must take better advantage of their strengths and achievements and remove the shortcomings that hinder them: nobody can do it for them!"

Jan 1, 1996

By Roy Lindsay, Paul O'Hara, Gary Halverson

"The New Britannia Minesite is located in Snow Lake, Manitoba, 420 miles north of Winnipeg (figure 1). The mine previously operated from 1949 to 1958 extracting some 5.39 million tons of ore at a 0.150 opt gold grade. From 1959 to 1986 the property was held by Nor-Acme and Hudson Bay Exploration and Development and in 1987 High River Resources Ltd. Optioned the property, dewatered the mine and conducted a diamond drill program between the 1 780 and 2400 levels. In 1988 two companies, Nor-Acme Mines Ltd. and High River Gold Mines Ltd., negotiated an option agreement with INCO Gold whereby !NCO assumed management control of all site exploration work. During this period, a bulk sample of 10,000 tons was extracted from the 1780 level with no further exploration recorded after its removal. Both Hudson Bay Exploration and Development and INCO Gold conducted feasibility studies on reactivating the property but at a calculated capital cost of Cdn $70 to $80 million found the rate of return on their investment unacceptable.In 1991 !NCO Gold merged its interest with the assets of TVX Gold Inc. and in February 1994 TVX Gold Inc. and High River Gold Mines Ltd. entered into a joint venture partnership to develop the Snow Lake property, naming TVX Gold Inc. the operator. Upon completion of a feasibility study in April 1994 by Bharti Engineering Associates Inc., a decision was made to reopen the Britannia Mine at an established project cost of US $33 million.Project construction commenced in July 1994 with the hoist house excavation. The first concrete for the hoist house level footings was poured on August 4, 1994 and the project was completed on October 1, 1995 at a cost of US $36 million. The first gold pour took place November 4, 1995.This paper not only presents the metallurgical aspects of the operation but also describes the novel approach used to complete the design and construction of the site facilities."

Jan 1, 1996

By J. A. M. Cano

Introduction Since the beginning of operations at the pellet plant at Ponta Ubu ES, Samarco Mineração SA has produced pellets for direct reduction and blast furnace processes. Of the total amount of pellets produced from 1977 through 1993, 55 % are used in the blast furnace, about 45 Mt (49.6 million st). The principal components of pellet gangue are calcium oxide, magnesium oxide, silica and alumina. They should be added in adequate quantities to guarantee the mechanical resistance of the fired pellets under blast furnace conditions. Over the years, the pellets produced by Samarco had a silica content between 2.5% and 2.8% and varying binary basicity preferably between 0.8 and 0.85. On the other hand, the increasing amount of industrial waste in siderurgical plants caused by the increase of steel production has caused some countries to put into practice methods to reduce the volume of slag produced in the blast furnace. This paper's goal is to find an alternative for decreasing the amount of slag produced in the blast furnace. It is possible to decrease pellet gangue by decreasing the silica content to about 2%, leaving the metallurgical properties and quality of pellets unaltered. For this work, Samarco pellets were used with Si02 between 2.5% and 2.8%, pellets with high silica and pellets with Si02 between 2.0% and 2.3% low silica. Both were partially fluxed by the range of varying basicity CaO/SiO2 from 0.8 to 0.95 during production. Experimental tests on pilot scale Thhis work began in January 1986 in the pilot plant (pot grate, Fig. 1) at Samarco. Its goal was to obtain preliminary data that would indicate the bybility of the project. It also formed a solid base to extend the studies in tests on an industrial scale of production for blast-furnace pellets. The pot grate is a test furnace composed of a gas burner, a combustion chamber and a grate, connected by hot air ducts. The burner is fed by a mixture of LPG and air. It reaches high temperatures through oxygen injection. The combustion chamber heats the air that comes from the turbocompressor. This hot air flows through the ducts to the grate on which the pellet samples are fired. During updraft drying, downdraft drying, preheating, firing and afterfiring, the upward and downward direction of the air flow can be controlled by valves driven by pneumatic cylinders. The pot grate indurator was fully automated in August 1989. Positive and negative pressures measurements resulting from gas passing through the pellet layer, as well as temperature readings, are recorded in graphs in relation to time for all tests. The tests depend on the various steps carried out in sequence that can influence the results of the tests. Therefore, some criteria were adopted to restrict the number of variables in the process. This was done to facilitate the results of the analysis. The pellets were composed of concentrate, bentonite, hydrated calcitic lime and metallurgical coal, all regularly used in the pellet plant. The material balance of the pellets mix was determined from the chemical analysis of the components. Table 1 shows the chemical characteristics of the concentrate and the additives used in the pilot plant and industrial tests. The basicity has a marked influence on the metallurgical properties of the pellets produced by Samarco with a silica content between 2.5% and 2.8%. However, for pellets with low silica (about 2%), it was necessary to study the variation in the parameters of quality in a wide range of basicities to deliniate with precision a scope of work. A large variety of low-silica blast-furnace pellets were produced at the pilot plant with binary basicity varying between 0.8 and 0.95. After chemical analysis, those pellets were separated into five groups of different binary basicity (0.8, 0.84, 0.87, 0.90 and 0.95). Each was then split, one part for metallurgical tests in the laboratory at Samarco and another to be evaluated in a laboratory for metallurgical tests in Germany. It was agreed that the tests to evaluate the quality of the pellets in the two [ ]

Jan 1, 1996

Situated in the Greymouth Coalfield, the Mt Davy Block contains a significant resource of high quality bituminous coal suitable for use in metallurgical coking coal blends. The coal, which is all low sulphur, is seen as a complementary deposit to export coking coal at Stockton Mine.   Previous drilling by State Coal Mines (1948 - 1953) and Japanese interests (1970's) have been supplemented by Coal New Zealand drilling (1992 - 1993) and surface mapping. A mining feasibility study was completed in late 1993 and approval gained for the driveage of an exploratory tunnel to the target seam.   Following construction of surface facilities, tunnel driveage on a 1:5 decline commenced from Rewanui in May 1995 and to date about half the required length has been driven. When the seam is intersected a comprehensive geotechnical testing programme will be undertaken to assess the in-situ mining conditions. It is expected that the results will confirm the assumptions made in the feasibility study.   The Mt Davy Mine, at depths of 500 - 700 metres, will be the deepest underground coal mine ever inNew Zealand and in-situ stresses (orientation and magnitude) will be important considerations for mining engineering. The coal has a high gas content and suitable techniques for gas control and prevention/mitigation of coal outbursts will be necessary.   Mine development is scheduled to commence in mid 1998 and an annual production level of 500 000 tonnes is forecast. The coal seams will be developed by continuous miner and coal extraction will be by hydraulic monitor. Coal will be pumped to the surface and from Rewanui transported five kilometres to Dunollie either by truck or slurry pipeline. At Dunollie a coal dewatering plant, coal stockpile and rail loadout will be constructed.

Jan 1, 1996

By G. I. Gritsko

In this paper we consider the elements of a distributed information geomechanic monitoring system which is used in computerized mine planning and mining operations control. The automated system is a technical means of geomechanic monitoring, as a complex system of regulated observations, estimation and prediction of geomechanic state of rock mass and workings during underground mining of coal deposits. Geomechanic monitoring at coal mines and the automated system execute data collection, analysis and calculations of geomechanic situation in the panel during planning, development and carrying-out of mining operations for ensuring geotechnical stability of underground mining.

Jan 1, 1996

By John D. VandeKraats

Yielding rock bolt support systems have been developed to accommodate ground movement in shifting ground such as in coal operations; in creeping ground such as salt, trona, and potash; and in swelling ground associated with some clays. These systems, designed to remain intact despite ground movement, should enhance mine safety and help contain costs in areas where rebolting of rigid non-yielding systems is typically required. Four such systems were tested in straight tensile pulls in the laboratory. They include the Slip Nut System from Dywidag Systems International USA, Inc., Ischebeck's bolt mounted Titan Load Indicator, Rocky Mountain Bolt Company's Yielding Cable Bolt, and a rock bolt installed variation of the yielding steel post developed by RE/SPEC Inc. The first two systems are currently marketed products and the latter two are prototype systems. Each system responds to load and displacement by yielding in a unique manner. All are designed to yield at predetermined loads. A description of each system and its yield function is provided. Each system was tested over its prescribed yield range in a test machine. At least five tests were performed on each system. Each system yielded and continued to provide support according to its design. Each shows promise for ground control use in shifting or creeping rock. This work helps to illustrate the comparative differences in performance between these specialized systems and the applications where they may be most useful.

Jan 1, 1996

By T. Harris

Exports of crude gypsum from Mexico currently comprise about 60% of all domestic shipments, and about 25% of the imported material consumed in the U.S. wallboard industry. However, of growing importance are the domestic markets for calcined gypsum in Mexico including building plasters and wallboard, which account for 55% of the internal demand for natural mined material. This paper will examine the current trends in the production and trade of natural mined gypsum in Mexico and North America and the opportunities and threats that are facing existing and new suppliers in this changing market.

Jan 1, 1996