Search Documents

Geotechnical conditions in the Lochiel Deposit are somewhat unusual, and thus geotechnical and hydrological investigations have assumed a high priority. The cost of mining the deposit has been shown to be very sensitive to geotechnical design parameters, and it is now seen to be of paramount importance to establish a high level of confidence in the design parameters used for mining cost estimation. Geotechnical investigations in the Lochiel Deposit reached a crossroads in 1985, when there appeared to be several quite different and equally attractive routes to follow to establish a satisfactory level of confidence in geotechnical mine design parameters. Three main options were identified, referred to as the No Further Work Route, the Drill and Trench Route, and the Trial Pit Route. The No Further Work Route was ruled out as being technically unsound and as satisfying none of the Electricity Trust of South Australia's (ETSA's) or the State Government's requirements. The planning process for further geotechnical investigation involved: clearly identifying the current status of work and significant geotechnical and geological factors planning and costing the alternative schemes for improving knowledge assessing the increase in knowledge to be gained from the alternative schemes . choosing the preferred scheme This process resulted in ETSA's

Jan 1, 1986

By B. Stimpson, K. Kosar, K. Barron

"A number of high wall failures have occurred in some of the Alberta coal strip mines of a type called by the authors ""Multiple block plane shear slope failure "". They cause rapid deterioration of the dragline bench, reduced productivity and maintenance costs.The failures are invariably associated with the presence of almost horizontal (± 5 degrees) bentonitic clay bands in the overburden, often immediately above the coal seam, and regress behind the slope as a series of tension cracks which isolate detached blocks. As many as 17 sets of cracks have been observed, at lateral distances in excess of five times the slope height from the toe.The theory of this mode of failure is presented and a limiting equilibrium computer program which will produce deterministic or probabilistic (Monte Carlo) solutions is briefly described. A case history of one such failure is documented. It is shown that the extent of the regressive failure is exceedingly sensitive to the water table elevation, leading to the conclusion that drainage, if practical, represents the best control strategy. IntroductionA number of high wall slope failures are occurring in some of the coal strip mines in Alberta of a type called by the authors ""Multiple block plane shear slope failure""(I). These failures cause a rapid deterioration of the bench from which the dragline operates, reduced productivity, and necessitate conregresses into the slope as a series of tension cracks and detached blocks. As many as 17 prominent cracks or crack zones have been observed, the last being in excess of five times the slope height distant from the toe.The block between each pair of cracks must be at limiting equilibrium, i.e. the factor of safety equals one. This condition can be used to determine the locations of the cracks which develop in sequence behind the face."

Jan 1, 1986

By Arel B. McMahan

The U.S. Bureau of Mines investigated 21 mines, prospects, and mineralized sites in and adjacent to a 38,713-acre portion of the 255,058-acre Kingston Range Wilderness Study Area in 1983. The study area is 35 miles north of Baker, CA in the Mojave Desert. Mineral deposits in and adjacent to the study area are in altered carbonate rocks intruded by diabase sills near monzonite porphyry contacts. Monzonite porphyry forms the core of the Kingston Range and underlies about 70 percent of the study area. Sedimentary carbonate rocks are exposed in bands on the north and east boundaries and as isolated roof pendants in the southeastern portion of the study area.

Jan 1, 1986

By Dermot Winters

The Surface Mining Control and Reclamation Act (SMCRA, or the Act) was enacted on August 3, 1977. The Act was written, in part, to put an end to uneven environmental standards and to establish minimum national standards. Certainly, one of the motivating factors for passage of the Act was the success of the Federal Coal Mining Health and Safety Act of 1969 in reducing deaths and injuries in the coal industry nationwide. Section 516 (b) (1) of the Act requires *that subsidence be prevented from causing material damage to the extent technologically and economically feasible except in those instances where the mining technology requires planned subsidence in a predictable and controlled manner. Section 516 (c) of the Act authorizes the regulatory authority to suspend underground mining if there is imminent danger to inhabitants of urbanized areas, cities, towns, and communities. On December 13, 1977, the interim program, which applies a portion of the performance standards of the Act, was promulgated. Then on September 18, 1978, the proposed permanent program was published for public comment. Finally, on March 13, 1979, the final permanent program was promulgated and the States were given a period of time to submit their programs for approval.

Jan 1, 1986

By David A. Benjamin

At the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied prospects, claims, and mineralized sites in a 43,053-acre portion of the 51,262-acre Desatoya Mountains Wilderness Study Area (NV-030-l10) in 1985. The study area, located 50 miles east of Fallon, NV, is underlain by alluvial deposits of Quaternary age and volcanic and volcanic-derived sedimentary rock of Tertiary age. No mines or recent exploration activity were identified within the area studied. The Gold Basin area, located 1/2 mile to the south has produced 982 ounces of gold and 10,086 ounces of silver. The Cold Springs area, located 1/2 mile to the west, has recently been explored for gold-silver. Mineralization at these two areas apparently did not extend into the study area, but future mining at these areas would likely impact it.

Jan 1, 1986

By David S. Robertson

"IntroductionCanada has been one of the world's leading producers of uranium since atomic energy first became of practical importance in 1942. Indeed, prior to this time, between 1933 and 1940, Canada produced significant amounts of pitchblende, as a source of radium, from the Eldorado Mine at Great Bear Lake*.Uranium was first reported in Canada, however, in the middle of the 19th Century in the vicinity of Theano Point on Lake Superior north of Sault Ste. Marie. In the early 1900s, uranium-bearing minerals were reported in Quebec north of the St. Lawrence River and in pegmatites in Quebec and eastern Ontario. In 1930, G.A. LaBine and E.C. St. Paul visited an occurrence of cobalt reported by the Geological Survey of Canada in 1900, and brought the Eldorado Mine into production in 1933, as noted above, producing, in the main, silver and pitchblende.In 1942, developments in atomic energy were such that the Government of Canada, at the behest of Great Britain and the United States, requested that Eldorado, which had been closed in 1940, be re-opened to produce uranium for the Manhattan Project. In September, 1943, all discoveries of radioactive minerals were reserved to the Crown and their staking by private interests was banned. In January, 1944, the government nationalized Eldorado and formed a Crown corporation, the present Eldorado Nuclear Limited, to take over the assets. That year marked the formal beginning of uranium exploration in Canada.The Period 1944 to 1948In 1944, the Crown Corporation and the Geological Survey of Canada began exploring for uranium deposits, largely in the areas of Great Bear Lake and Lake Athabasca. In that year, A. W. Joliffe of the Survey visited properties on the north shore of Lake Athabasca near Beaverlodge Lake and recommended that Eldorado acquire claims in the area. In 1946, P. St. Louis and E. Laurum, prospectors working for Eldorado, found the pitchblende veinlets that led to the Ace Mine. Shaft sinking began in 1951, and production, through a carbonate leach plant, began in 1953.Continuing drilling on the Eldorado claims led to the Verna ore bodies, some 6,000 feet northeast of Ace, on which shaft sinking started in 1954."

Jan 1, 1986

By T. P. Mucho

Over the past several years, two types of roof control problems have been en- countered at Beth Energy's Eighty Four Complex mine in Southwestern Pennsylvania. These problems have been (1) poor roof conditions encountered while advancing submain entries and longwall panel entries and (2) deterioration and failure of long- wall gateroads, principally the tailgate entry. This paper discusses the efforts by mine personnel to analyze the origins of the various attempts to-deal with the problems, and the success (or failure) of these efforts. Highlighted are the use of various common roof Control materials, variations in mining techniques, cementatious pillars, and changes in pillar design using yield and abutment pillars to address these problems.

Jan 1, 1986

By W. E. Sabina

In the short period of one mans? career we have seen specifications for bulk material handling systems and equipment grow from two or three pages to as much as two or three volumes for a single contract. The old 'short form' described what the purchaser expected the equipment to do. The long form does the same but also includes nut, bolt, and lockwasher depth of detail. What are the events that led to this proliferation of verbiage, and does it benefit the buyer in the final analysis? Is there a better way to purchase complex equipment while ensuring the highest quality for the dollar spent?

Jan 1, 1986

By Kewal K. Kohli, Thomas Z. Jones

This paper presents a simplified computerized method for the prediction of maximum subsidence and the subsidence profile for the Appalachian Coal Basin using the Hyperbolic Function Profile Method. Several case histories are cited to demonstrate the appropriateness of the predictive method. In addition, sample runs and a detailed listing of the computer program is provided. Other popular subsidence prediction methods are discussed and compared with the Hyperbolic Function Profile Method.

Jan 1, 1986

By Edward L. McHugh

The study area, which comprises 11,500 acres, includes the 9,610-acre Whitewater Wilderness Study Area, in the California Desert Conservation Area, 15 miles northwest of Palm Springs, CA. The U.S. Bureau of Mines evaluation of mineral resources is based on examination of prospects and mineralized areas during the spring of 1981. The Whitewater study area is mainly underlain by granodiorite to quartz diorite and their gneissic equivalents in an igneous-metamorphic complex. Late Tertiary sedimentary and volcanic rocks locally overlie the crystalline complex in the eastern part of the study area. The study area lies between branches of the San Andreas fault system.

Jan 1, 1986

By Keith A. Heasley, Lee W. Saperstein

This paper investigates the use of backfill zones and yielding pillars for subsidence control. The investigation begins by choosing an appropriate subsidence predictive technique to simulate the proposed subsidence-control schemes. Two case studies are performed in order to delineate the accuracy and utlility of the chosen predictive technique and then the results of these case studies are used to establish appropriate sets of regional site parameters. Next, a detailed analysis of the major variables affecting the outcome of the subsidence-control simulations is conducted and graphical displays of the exact sensitivity of the surface subsidence to these variables are given. Finally, alterations to the surface subsidence that are expected from using two major subsidence-control techniques are presented. The first technique to be assessed is a backfilled pillar centered longitudinally in a panel. With this arrangement, a minimal amount of backfill material can produce substantial decreases in vertical displacements. The second technique to be assessed is the use of yielding gate pillars to reduce the sinuosity of the transverse subsidence over adjacent panels. With proper design, this technique can greatly curtail surface strains and help minimize remedial drainage control.

Jan 1, 1986

By Steve Meador

West Virginia's basic coal mining regulatory programs are not unique when compared to Federally approved programs implemented by other coal producing states. In fact, the language in The West Virginia Energy Act governing subsidence mirrors that written in the Federal Surface Mining Control and Reclamation Act as well as other states' statutes. Certain legal and administrative issues, how¬ever, combine to make West Virginia's regulation of surface subsidence a singular approach.

Jan 1, 1986

By R. D. Lindsay

"Pamour Porcupine Mines, Limited is involved in the mining, milling and primary refining of various gold, gold - copper and refractory gold ores. Pamour operates five mines in the Porcupine Mining District of Ontario, and two 2,550 t/d milling facilities.Both metallurgical facilities use conventional cyanidation technology including zinc cementation for precipitation of gold and silver from solution. The precipitation process, as applied to clarified leach solutions (less than 1 ppm suspended solids) at Pamour is called the Merrill - Crowe process. Precipitates from both milling operations are treated at Pamour's Area Refinery. Schumacher precipitates, unlike Pamour No. 1, require an ''Acid Treatment Stage"" prior to refining to remove the high contained copper. This is accomplished by leaching the precipitates initiallv with sulphuric acid to remove zinc and then with sulphuric acid and manganese dioxide to dissolve copper. Refining procedures after ''Acid Treatment"" are essentially the same for both precipitates.The following considerations highlight the basic principals applied to refining cyanidation precipitates at Pamour, including:"

Jan 1, 1986

By Fardy J. J

Abundance data are presented for a comprehensive range of elements in oil shale samples from deposits located in Queensland. The techniques of instrumental neutron activation analysis and spark source mass spectrometry were used to obtain concentration data for up to 50 trace elements in each shale. These techniques were supplemented by other spectrometric methods to obtain data for major, minor and some trace elements. Sixty-four elements were determined quantitatively. This comprehensive characterisation of oil shale samples from the major deposits in Australia provides inorganic abundance data not previously available. It also provides important background information for processing studies and the associated environmental aspects of shale oil production and waste disposal.

Jan 1, 1986

Wastewaters from Mining Projects both gold mining and coal mining generally have minerals in solution or very fine material which does not settle out quickly. These waters in the past have been discharged into the nearest water course and caused extensive pollution.

Jan 1, 1986

By Gordon M. Matheson

The factors which control chimney subsidence sinkhole development in weak rock were assessed by analyzing the characteristics of approximately 3000 chimney subsidence features along the Colorado Front Range. The area of study included features developed over abandoned mines in the Colorado Springs Coal Field, the Boulder Coal Field, and the Foothills District. The approximate locations of the areas studied are shown in Figure 1. Data were collected for sinkholes occurring over both room and pillar, and retreat mining areas in coal seams with a wide range of dips. The location, size, and approximate time of development of each sinkhole were documented. From these data, relationships were developed which describe the time rate of observable sinkhole development and the relative location of sinkhole development with respect to mined height, overburden thickness, and type of mining for relatively flat-lying coal seams. In addition, the observed locations of sinkhole development over steeply dipping coal seams were assessed for portions of the study area.

Jan 1, 1986

By B. F. Westfall

Throughout the 1960's and 1970's world trade grew rapidly, reaching a peak of USS1.8 trillion in 1980. Since then the world recession of the early 1980's shrunk trade to about US$1.6 trillion. The reduced cash flow to developing economies made it difficult to service their huge international debts, Nowadays lenders are reluctant to grant Third World countries additional credit. The shortage of export financing, plus trade barriers set up by developed countries, is further inhibiting international trade. Therefore, countries are turning to new and creative alternatives to financing imports of consumer as well as of investment goods. Non-cash transactions, including different forms of countertrade, are rapidly growing alternatives to traditional trade financing patterns. In 1983 about 30% of international trade, or close to US$600 bill ion, were presumably done by non-cash transactions, up from barely 2% in 1976. By year 2000, half the world trade is likely to be conducted on basis of barter. As of mid-1984 some 88 nations used countertrade regularly and Governments of at least 15 Latin American countries had arranged or mandated commercial countertrade.

Jan 1, 1986

Three computerised sets of minerals information are being developed by New Zealand Geological Survey in co-operation with the Resource Management and Mining group of the Ministry of Energy: 1. Geological Resource Map: a file of information on the location, geology, geochemistry, production, and potential use of individual occurrences of aggregate, mineral, geothermal, coal, oil, and gas resources. The computer program can be used for search and retrieval of information and the production of maps and tables. The data is being published as a series of 1:250 000 maps with accompanying text and tables. 2. Minerals Bibliography: an index and retrieval system for mineral exploration related; open-file company reports, N.Z. Geological Survey files, scientific research publications and university theses. 3. Minerals WhoÆs Who: an annotated directory of geologists involved in mineral exploration, mining and research.

Jan 1, 1986

By R. D. Smith

The Bureau of Mines (BOM) evaluated the technology, capital investment, and annual operating costs of emission control for further reductions of lead in ambient air at the East Helena, Montana, smelter, and the Glover, Herculaneum, and Buick smelter-refineries in Missouri. This study seeks to analyze the technology available to the domestic primary lead industry for attempting to further reduce lead emissions below 1985 levels. Through enclosure of concentrate unloading and handling areas and all lead-processing buildings, followed by venting these enclosures to the atmosphere through baghouses and the application of appropriate local controls, emissions can theoretically be reduced by a total of 2,424 pounds of lead per day from 1985 levels at the three Missouri operations. Using conventional technology, aggregated additional capital costs of $250,014,000 and annual operating costs of $18,507,800 are estimated for the four operations, resulting in a total cost of $0.063 per pound of refined lead. Continuous drossing techniques would assist in meeting OSHA standards in process areas. Continuous drossing would change capital and operating costs to $258,344,800 and $16,104,700, respectively, for a total cost of $0.062 per pound of refined lead. First quarter, 1986 open market price for refined lead was $0.184 per pound.

Jan 1, 1986

Economically significant gold-silver mineralization occurs in Miocene andesitic flows and tuffs at Golden Cross, eight kilometres northwest of Waihi, New Zealand. The highest grade mineralization occurs in a steeply dipping elongate zone of strong quartz veining and brecciation underlying, but contiguous with, a gently dipping tabular quartz vein stockwork containing potentially open-pittable lower grade gold-silver mineralisation. The stockwork zone is enveloped by argillic alteration and overlain by unaltered Pliocene andesites and recent tephra. Evaluation of the prospect involved underground and surface geologic mapping, rock and soil geochemistry, IP-resistivity, magnetic and gravity surveys as well as 1844 metres of reverse circulation drilling and over 30 000 metres of core drilling. The paper outlines the exploration history of the area and describes the results of the various exploration techniques used at Golden Cross.

Jan 1, 1986