Search Documents

By Jue Kou, Lei Yu, Bern Klein, Lusheng Zhou, Chunbao Sun, Genzhuang Li, Reem Roufail, Amit Kumar

Magnetic liners can improve the performance of ball mills by increasing grinding efficiency, extending service life, and reducing maintenance costs. Despite their importance, the fundamental understanding and the quantitative investigation on the effects of the magnetic liners has not been addressed in the literature. This paper addresses this gap by studying charge motion, and how the use of a magnetic liner affects the breakage mechanism of the mill, using discrete element method (DEM) modeling and the Hertz-Mindlin contact model with relative velocity dependent (RVD) rolling friction. Charge motion was modeled under different mill speeds. Compared to conventional steel and rubber liners, the charge motion in the magnetic liner mill was predominantly cascading. Quantitative analysis of the energy dissipation within the mill was conducted to investigate mill breakage. Regardless of speed, over 50% of the total energy dissipation in the magnetic liner mill was in the form of abrasion and attrition. The results highlighted the appeal of magnetic liners in secondary and regrinding application, where abrasion and attrition are considered more efficient in the fine material breakage, and where impact is ideally minimized to reduce mill wear. A number of experiments were conducted to assess the effect of different model parameters on the performance of the magnetic liner mill. The highest abrasion/attrition intensity was observed with high values of the model parameters namely the restitution coefficient, static friction coefficient, and rolling friction coefficient.

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

A common problem during the operation of the Kaldo furnace is the formation of accretions and blockage of the injection lance due to splashing. This typically occurs during the processing of anodic slimes for the production of doré. In this work, a 1:7 scale model of the Kaldo furnace currently in operation at Metalúrgica de Cobre, Mexico, was built in transparent acrylic plastic. Water and colored oil were used to represent the doré and slag, respectively. The model was used to determine the maximum penetration distance of the injection lance under a variety of experimental conditions at room temperature. Input variables included two types of oil, rotation speed, inclination angle, and the fraction of the vessel volume occupied by the liquids (φ). A mathematical correlation for the dimensionless maximum penetration distance of the injection lance d ∗ as a function of φ, the Froude number of the liquids in the vessel (Fr), the Reynolds number of the gas jet (Re), and the oil-to-water kinematic viscosity ratio (η)was developed. Reasonable agreement between the calculated and experimental values was obtained. Digital images showed that splashing was caused by the turbulent gas jet impinging upon the free surface of the liquids, whereas the cascade effect was negligible. The results of this work have been useful to improve the operation of an industrial Kaldo reactor.

By Stephen C. Tadolini, Thomas M. Barczak

Roof support systems, longwall shields in particular, have persistently grown in size and capacity for the past 25 years. Why is this? Is it a good thing or is it unnecessary? What are the consequences of this “bigger-the-better” design philosophy? Rarely do we see a “one size fits all” approach to roof support except when it comes to longwall shields, where the historical trend for new procurements is to simply purchase the highest capacity support you can buy. Does high capacity ensure failures will not occur? The answer is no! The highest capacity tailgate supports are typically the ones that fail the most often. What does this tell us? It tells us that there are fundamental aspects of support design and ground control that we still do not understand or recognize when designing a support system. This paper provides an interesting evaluation of these issues and proposes a different approach to support design that attempts to match the support performance characteristics to the ground behavior. Along the way, some of the old premises of support design will be discarded, and new “controversial” ideas developed. Thinking outside the box never hurt any industry. Mining has made it a common practice.

By R. J. Matetic, David S. Yantek, David K. Ingram

The National Institute for Occupational Safety and Health (NIOSH) has investigated engineering noise controls to reduce sound levels in cabs on air-rotary drill rigs. A recent investigation revealed that some drillers are exposed to A-weighted sound levels exceeding 85 dB even though a cab is used. NIOSH studied the in-cab sound levels of one such rig. First, preliminary tests were conducted in a controlled environment using accelerometers and microphones with spectral analysis to identify the dominant noise sources for in-cab sound levels. The results indicate that vibration transmitted from multiple hydraulic pumps to the control panel produces a dominant spike in the sound level spectrum in the 400 Hz 1/3-octave band. Next, field tests were performed in a production environment to evaluate noise controls to reduce in-cab sound levels. It was found that utilizing hydraulic noise suppressors reduces the structure-borne noise transmitted to the control panel. Further, using hydraulic noise suppressors and enhancing soundproofing reduced the in-cab A-weighted sound levels by as much as 4 dB.

By S. Maurhofer

The Uetliberg Tunnel in Switzerland is the longest tunnel in Zurich?s new Western Bypass Expressway, connecting the Birmensdorf bypass in the west with the existing Zurich-Chur national motorway in the east. Thus the tunnel links the Zurich-West motorway interchange with the Zurich-South interchange (shown in Figure 1). The Uetliberg Tunnel project comprises two parallel tubes, each about 4.4 km long. The two tunnel tubes are connected every 300 m by a transverse walkway and every 900 m by a transverse roadway (Figure 2). The SOS niches are spaced 150 m apart. Portal stations with machinery rooms are located at the west and east portals. The tunnel falls with a gradient of 1.6% from the west portal at Wannenboden to the east portal at Gänziloo. The Project costs are about CHF 1.12 billion. The carcass construction started in March 2001. The Opening of the Uetliberg Tunnel is planed in spring 2009.

By S. J. Schatzel, W. P. Diamond

Longwall mining alters the fluid-flow-related reservoir properties of the rocks overlying and underlying an extracted panel due to fracturing and relaxation of the strata. These mining-related disturbances create new pressure depletion zones and new flow paths for gas migration and may cause unexpected or uncontrolled migration of gas into the underground workplace. One common technique to control methane emissions in longwall mines is to drill vertical gob gas vent holes into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important to optimize the well parameters, e.g., the borehole diameter, and the length and position of the slotted casing interval relative to the fractured gas-bearing zones. This paper presents the development and results of a comprehensive, "dynamic," three-dimensional reservoir model of a typical multipanel Pittsburgh coalbed longwall mine. The alteration of permeability fields in and above the panels as a result of the mining- induced disturbances has been estimated from mechanical modeling of the overlying rock mass. Model calibration was performed through history matching the gas production from gob gas ventholes in the study area. Results presented in this paper include a simulation of gas flow patterns from the gas-bearing zones in the overlying strata to the mine environment, as well as the influence of completion practices on optimizing gas production from gob gas ventholes.

By Richard Mainiero, Donald A. Hurd, James H. Rowland

In previous conferences the authors have reported on toxic fumes generated by the detonation of ANFO. The research reported here extends the earlier work to include an emulsion blasting agent and ANFO/emulsion blends. Explosive mixtures were shot in 4-inch Schedule 80 steel pipe in a chamber in the experimental mine at the Pittsburgh Research Laboratory (PRL). Following each shot, the fumes in the chamber were analyzed using on-line instrumentation. A major goal of the research was to gain a better understanding of the factors that lead to the generation of toxic fumes in blasting operations. Earlier studies have suggested that the high nitrogen dioxide and nitric oxide concentrations in product clouds might be the result of the poor confinement provided by relatively weak ground strata or the exposure of the explosive to ground water prior to shooting the shot. Various mixtures of ANFO and emulsion were detonated in schedule 80 steel pipe and galvanized sheet metal pipe to evaluate the effect of confinement. Explosive mixtures were also allowed to soak in water for less than one day, one week, one month, and two months to determine which explosive mixtures would be degraded and observe what effect this degradation had on fume production. Results indicated that the production of nitrogen dioxide increased with low confinement of the detonating explosive and with exposure of the explosive to water.

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

By Ed D. Thimons, Douglas E. Pollock, Andrew B. Cecala, Gregory J. Chekan, Jay F. Colinet, John A. Organiscak

Researchers at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) work to reduce respirable dust exposures in mining operations. One focus of this research is silica dust control for surface and underground operations in the metal/nonmetal mining industry. PRL researchers analyze dust sampling results from the Mine Safety and Health Administration (MSHA) to identify high-risk occupations to guide research efforts. Research is then conducted in an effort to improve existing technologies and/or develop new controls for reducing worker exposure to airborne silica dust. During the last few years, PRL researchers have conducted research related to the following goals: improving protection provided by enclosed cabs on mobile surface mining equipment, reducing dust generation from surface drills, reducing dust levels in iron ore operations, and developing a new method to clean dust from workers’ soiled clothes. A description of each of these controls and subsequent dust reductions quantified through site surveys will be provided.

By A. López-Valdivieso, M. A. Corona-Arroyo, M. Llamas-Bueno

Magnetite (Fe3O4) ore is concentrated by low-magnetic-field drums to recover a magnetite concentrate that is low in silica (SiO2). The presence of SiO2 in the magnetite concentrate for steel production increases the steel processing costs, so a major challenge in magnetic concentration is to lower the SiO2 grade in the Fe concentrate. This work presents studies that were carried out on the removal of SiO2 from the magnetite concentration at the plant scale. Studies were performed with a three 36 × 96″ drum unit processing 46 ton/h of rougher magnetite concentrate. These studies showed that silica appears in the magnetite concentrate by three mechanisms, namely SiO2 entrainment in Fe3O4 chains, heterocoagulation between Fe3O4 and SiO2 particles, and mineral locking of SiO2 to Fe3O4. The SiO2 entrainment mechanism had the highest contribution (75%) to the SiO2 recovered in the Fe concentrate. Electrokinetic studies on Fe3O4 and SiO2 showed that heterocoagulation occurs because of the low negative zeta potential of the minerals at the pH of the plant slurry. This study also showed that a high percentage of ultrafine size SiO2 particles trapped in Fe3O4 agglomerates was not removed by the dilution water for the slurry fed to the drum. To lower the SiO2 recovery in the drum magnetic concentration process, work should be directed towards the removal of trapped SiO2 in Fe3O4 agglomerates.

By C. O. Karacan, S. J. Schatzel, W. P. Diamond

In coal mining, longwall mining is a preferred method to maximize production by extracting large blocks of coal that have been outlined with a set of development entries. In U.S. mines, longwall panels are typically 305 m (1,000ft) wide (with a continual trend towards even wider panels), and usually over 3,050 m (10,000ft) in length. The increasing size of longwall panels, while helping to increase coal production, may also increase methane emissions due to the exposure of the mining environment to a larger area of fractured, gas-bearing strata. Thus, understanding the impact of increased panel widths on methane emissions, and designing gob gas ventholes and bleeder systems accordingly, can enhance the safety of the underground workforce by reducing their exposure to potentially explosive accumulations of methane/air mixtures. As part of its mine safety research program, NIOSH’s Pittsburgh Research Laboratory has initiated a reservoir modeling effort to better understand the interaction of the various geotechnical factors influencing gas flow within and to the underground longwall mining environment. A focus of this modeling effort has been 1) the prediction of the incremental amount of methane emissions to be expected due to increasing longwall panel widths, and 2) optimizing gob gas venthole completion practices to capture more of the gas in the subsided strata above longwall panels before it can enter the ventilation system of the underground workplace. The history matching phase of the study has been carried out on a 381-m (1,250ft) wide panel in the Pittsburgh Coalbed. Simulations have also been completed for a 442 m (1,450ft) wide panel to estimate the incremental increase in methane emissions and the performance of current gob gas venthole placement configurations. Additional venthole placement configurations were simulated to investigate options for optimizing methane capture from the subsided strata above the wider longwall panel.

By T. M. Barczak

Longwall tailgates in coal mines are often subject to severe mining induced loading and deformation. Innovative tailgate supports have been developed over the years to provide safe and economical access and a ventilation pathway at the tailgate. The support capacity and yield capabilities of the supports need to be matched to the loading imposed by the surrounding rock mass. The ground response curve can be used to represent the rock mass response to mining and its effect on support systems. The FLAC finite difference code was used to supplement field results by simulating a longwall tailgate and the associated ground response. The ground response curve is developed by modeling tailgate excavations with different internal support pressures and recording the resulting convergence. Ground response curves are developed for two typical longwalls operating in the Pittsburgh seam with weak and strong immediate roof. An additional model is presented in which the effect of weak overburden strata is simulated. The ground response is shown to be significantly affected by the strength of the immediate roof as well as the main roof. The importance of yield capacity of standing support is demonstrated. Gob height and compaction are found to affect the amount of convergence in the tailgate. The potential exists to develop site specific tailgate design curves by combining model results with field observations.

By Giorgio De Tomi, Ricardo Tichauer

Mineral exploration is a critical step for success in mining. However, small-scale mining often ignores exploration best practices. This paper introduces the Tichauer-DeTomi Matrix, a tool for assessment of geological uncertainty in small-scale mining. This matrix, which measures the level of compliance of exploration programs in small deposits with industry best practices, has been applied to three small mining projects in Brazil: an artisanal gold mine in the Amazon, a small-scale manganese mining venture in the Northeast, and a small manganese deposit in the Southeast. The application of the matrix resulted in indexes that reflect the actual level of maturity of the mineral exploration program in each project. Therefore, the matrix has shown potential to be an effective tool for assessment of the geological uncertainty remaining in small-scale mineral projects, as well as to identify priority exploration activities for reduction of risks associated with the geological uncertainty. As a risk assessment tool, the TichauerDeTomi Matrix may be helpful in promoting investment and sustained development in and around small mines.

By Michael Zachariah, Art Miller, David Kittelson, Gib Ahlstrand

This report describes an investigation in which we used iron-doped diesel fuel to generate metal-bearing diesel particles and a subsequent analysis of the particles using transmission electron microscopy (TEM) and energy-dispersive spectroscopy (EDS). For this study, DPM was generated by a 1.5-L diesel engine and the fuel was doped with ferrocene to enhance the level of iron in the system. The exhaust particles were collected on TEM grids and analyzed using the Philips CM12 TEM/EDS instrument. Results show that when the iron-to-carbon (soot) ratio (Fe/C) in the engine is low, the exhaust particles have morphologies similar to those for the undoped case, but at a threshold Fe/C value of 0.013 (for this engine), homogeneously nucleated metallic nanoparticles are formed and begin agglomerating. The number and size of these nanoparticles increase with level of doping. Metal-bearing particles that span a wider size range are also formed. Agglomeration of metallic and carbon particles is observed in two distinct modes: attachment of iron primary particles (5–10 nm in diameter) to carbon agglomerates, and coagulation of iron agglomerates (20–200 nm in diameter) with carbon agglomerates. Results of this work imply that as new engine technologies reduce soot levels in the engine and/or levels of trace metals in the fuel are increased, the generation of metallic nanoparticles may ensue, creating a potential health concern. Keywords: Nanoparticles; Particulate emissions; Metallic particles; Metal emissions

By Scott Rosenthal, Kyle Murphy

This paper discusses the trials and tribulations of obtaining Velocity of Detonation (VOD) readings in small diameter blast holes in an underground mine. Montana Technological University (Montana Tech) obtained a time-domain reflectometer (TDR) type VOD monitoring unit. Purchase of the VOD monitor was justified on verifying explosives performance used in Montana Tech’s practical underground mining class and provide a teaching aid for the school’s rock fragmentation class. Before demonstrating the unit to students, we figured we better learn how to use it first so we give the students an appropriate experience. Our first learning was in obtaining the correct coaxial cable for the VOD monitor and how to properly terminate the cable. Once the cable was on-site and terminated, VOD testing could commence. Use of the VOD monitor was tested underground in small diameter holes (1.5-inch, 38 millimeter) pneumatically loaded with ANFO. After a few failed trials, and follow-up discussions with the supplier, VOD readings were obtained for the ANFO loaded holes. Additional readings were obtained for a pre-split product and detonating cord to satisfy our curiosity that the unit was performing as specified by the manufacturer. This paper will share our learnings in the hopes that others can benefit.

By M. A. Trevits, I. R. Houlison, A. C. Smith, T. P. Mucho

Timely and rapid intervention to underground combustion events (fires, explosions, and spontaneous combustion) is the key to the successful control of the mine atmosphere and restoring of a coal mine to production. The focus of this paper is the utilization of a GAG 3A jet engine system to combat either large out-of-control fires or to render an entire mine inert when access to problem areas is difficult or impossible. This system is based upon a Soviet designed agricultural jet engine which consumes aviation fuel with oxygen (O2) from the intake air and exhausts combustion gases, primarily carbon dioxide (CO2) and water (H2O), along with the nitrogen (N2) from the air and small amounts of carbon monoxide (CO) and hydrogen (H2). The system is designed to approach stoichiometric combustion (ideally, pure burning that scavenges all the oxygen from the intake air). Therefore, these exhaust gases are almost entirely “inert gases”- i.e., gases which do not contribute to, and in fact, can suppress the combustion process due to the lack of oxygen. Other methods to inert mine areas have been used in the US and internationally, but these methods usually use low flow inertisation equipment or methods. Use of these low-flow inertisation equipment and methods has been successful in proactively rendering gob areas inert and has the ability to inert the entire mine workings. Due to the low flow rate, however, a substantial period of

By Michael J. Jorgensen, Pranathi B. Aedla, N. K. Kittusamy

Risk factors associated with the development of muscu­loskeletal discomfort and disorders during the operation of heavy mobile equipment include whole-body vibration and awkward and sustained joint postures of the shoulders, neck, and trunk. Cab design may influence awkward postures of the joints, and task duration may influence duration of exposure to awkward and static postures and whole-body vibration. To reduce exposure to risk factors related to the interface between cab design and task, it may be necessary for manufacturers to address cab design. This study assessed the repeatability of a cab design checklist developed to evaluate various design characteristics that can influence exposure to risk factors for musculoskeletal discomfort. The ability of the cab design checklist to identify posture-related deficiencies of design was also assessed. The checklist was used by two administrators across 10 pieces of heavy construction equipment. Video analysis was performed to quantify postures of the neck, shoulder, and trunk; correlation analysis was used to determine whether specific questions from the checklist were associated with the identification of awkward postures. The repeatability assessment resulted in kappa coefficients ranging from 0.52 to 1.0 (good-to-excellent reproducibility) across each piece of equipment, and an overall kappa coefficient of 0.77 (excellent reproducibility) when considering all equipment together. Results from the correlation analysis showed that shoulder flexion posture was correlated with scores from the cab design checklist. However, results of the cab design checklist were not significantly correlated with shoulder abduction or awkward postures of the neck and trunk. Results suggest that the cab design checklist may be useful for identifying cab design characteristics that need further improvement and for identifying design characteristics that increase shoulder flexion. The strength of the repeatability assessment suggests that outcomes of the cab design checklist administered by different individuals may be consistent, independent of the type of equipment being assessed.

By Kentaro Kuraji

INTRODUCTION Background Tokyo, the capital of Japan, is one of the largest cities of the world. As many as 33 million people live in Tokyo and three neighboring prefectures although the city occupies only 0.6% of the area of the country. The network of Metropolitan Expressways serves as a major artery for daily physical distribution in Tokyo. The Central Circular Route of the Metropolitan Expressway (MECCR) is located innermost among the three circular routes in Tokyo (Figure 1). Once completed, MECCR is expected to drastically mitigate traffic congestion in the central Tokyo area and provide drivers wider varieties of options in route selection. Alleviating congestion is estimated to reduce 400,000 tons of carbon dioxide emissions annually. The eastern and northern sections and part of the western section of MECCR have been completed with the total length reaching 33 km. The western section will be extended southward by approximately 4 km in the spring of 2010. An 11-km-long western section of MECCR that is currently being constructed is composed mostly of tunnels. A large number of power supply, gas supply, telephone, drinking water and sewerage pipes have been placed under the Yamatedori avenue along which MECCR is being constructed. The shield tunneling method has therefore been adopted for constructing tunnels along the route. The method involves the advancement of a shield tunnel boring machine (TBM) through the ground simultaneously assembling segmental rings within the shield. The method not only enables the building of highway tunnels more quickly and efficiently than other methods but also minimizes the effects of construction work on the surrounding area and the environment. Constructing the tunnel using the conventional cut-and-cover method might have required large amounts of time and cost because relocating the numerous objects buried under the Yamatedori avenue might have been necessary during tunnel construction. It was also considered desirable to place the tunnel at a depth of 30 m or more from surface to prevent tunnel construction from adversely affecting railways because the tunnel was expected to cross eleven railways and subways. This is one of the reasons for selecting shield tunneling as an effective method. The shield tunneling method was finally adopted for a length of 7 km in the 11-km western section of MECCR. The shield tunneling method was also employed in the Ohashi Tunnel located southernmost in the 11-km western section of MECCR. This paper describes the construction of the Ohashi Shield Tunnel.

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By Pelin Altinkaya, Maria Leikola, Jussi Liipo, Mika Haapalainen, Mari Lundström, Eero Kolehmainen

With decreasing ore grades, the tailings of mining operations are becoming of increasing interest as metal-containing secondary raw materials. The objective of the current work was to investigate chloride leaching of gold, copper, cobalt, nickel, and zinc present in the flotation tailings. In the current study, the effect of cupric ion as an oxidant (0–50 g/L) and NaCl (150–250 g/L) on metals extraction was investigated. The other parameters, such as pH (1.8), temperature (95 °C), solid/liquid ratio (25%), oxygen feed rate (1200 mL/min), leaching time (24 h), and stirring rate (950 rpm), were kept constant. Gold dissolution rate was shown to increase with increase in cupric ion concentrations up to 50 g/L. Also, increase in NaCl concentration up to 250 g/L increased gold extraction. Majority of the copper present in the flotation tailings could be dissolved with all the all solutions investigated. The other base metals, cobalt, nickel, and zinc extractions were also shown to increase with increase in the cupric ion and sodium chloride concentration. However, even in the absence of cupric ion addition (t = 72 h, 250 g/L NaCl), the final extraction of Cu, Ni, Zn, Co, and Fe increased up to 98, 93, 83, 76, and 80%, respectively. This shows the power of inherently originating oxidants present in the tailings. Furthermore, the solid analysis of the leach residue indicated that leaching the flotation tailings in pure NaCl may result in partial gold dissolution. The results demonstrate that significant amount of metals present in the tailings could be extracted even with only NaCl as added chemical in the presence of oxygen feed, oxidizing agents originating directly from the raw material. This can provide an advantageous cyanide-free method for extraction of metals from very low-grade tailings with low chemical consumption.