Search Documents

By Hemingway P, Boag J

Major operating aspects of the Mary Kathleen Uranium Ltd. treatment plant are discussed with partkular reference to those which are peculiar to this operation.Problems associated with the production of a penalty free uranium oxide product are examined and the methods developed to overcome them are described in detail.INTRODUCTIONMary K,athleen Uranium Ltd. is the largest of the Australian uranium producers. The flow-sheet is based on fine grinding, standard sulphuric acid leach, ion exchange concentration, and magnesia precipitation of the final product, with certain modifications introduced as the result of pilot plant investigations at the South Australian Department of Mines Research Laboratories in Adelaide.The plant commenced operations in June, 1958, attained design tonnlige of 1,120 tons per day in September of that year and has since operated continuously with a throughput in excess of 1,000 tons per day. Pilot plant recommendations generally have been followed, and predicted results have been attained. The only exception has been the silica and rare earth content of the product produced during the early months of operation. Considerable modification of the early resin regeneration techniques resulted in the reduction of the silica content of the product to within specification limits. Research work in the ion exchange section has also resulted in the reduction of the rare earth content of the product to below specification levels. All product now being produced is completely within the agreed specification limits of impurities.

Jan 1, 1961

By M. A. Elliott

The technology of gasifying coal to produce synthesis and pipeline gas has advanced significantly in the Past 20 to 30 years. This period has seen the extensive use of oxygen in coal gasification, the development of suspension gasification processes and fluidized-bed gasifiers, the operation of various gasification processes at elevated pressures, and operation of gasifiers under slagging conditions. These developments are discussed, and their application to commercial and pilot plant gasifiers is reviewed. Typical processes for synthesis gas production are described, and operating results are compared. Pipeline or high-Btu gas may be produced from coal either by catalytic conversion of synthesis gas to methane, or by the direct reaction of coal with hydrogen (hydrogasification) to produce a methane-rich gas. Neither of these methods has been applied commercially, but developments pertaining to each of them are reviewed, and general processing schemes are discussed. The use of coal as a raw material for manufacturing gas has a long and distinguished history. In fact, the gas industry began in the early 1800's when William Murdock demonstrated that it was feasible to produce and distribute gas made by retorting coal. Coal was used exclusively for gas manufacture until the middle of the 19th centruy, when Lowe invented the carbureted water gas process. In that process, coke was one of the raw materials used, so coal was still an important factor in gas manufacture. However the availability and relatively low cost of natural gas in the United States, and its widespread distribution by long-distance pipelines in recent years, has virtually eliminated the use of coal as a raw material for gas manufacture in this country. It should not be inferred from the foregoing that the technology of coal gasification has remained static in the United States and abroad. In fact, in the past two decades many new concepts have been developed in both the science and the technology of gasification. This progress has been a result of the considerable expansion in research on the fundamental chemistry and physics of gasification reactions, and in development work on gasification processes. This expansion in effort stems in part from increased interest in the use of gas as a raw material for the synthesis of chemicals and liquid fuels, and in part from the need to develop methods for gasifying coal and other solid fossil fuels to ensure a long-range supply of energy in the form of gaseous fuel. In these uses of gas, synthesis gas, a mixture of hydrogen and carbon monoxide in various proportions, is the starting material. It may be converted catalytically to gaseous and liquid hydrocarbons and other chemicals, or to hydrogen for use in hydrogenation or reduction reactions. Since coal is our most abundant fossil fuel, it is inevitable that one day it will regain its prominence as a raw material for gas manufacture. It is of interest, therefore, to consider the present status of gasification technology, directing attention particularly to advances made in recent years. Inasmuch as many comprehensive treatises l-3 and review4-7 of gasification technology are available, no attempt will be made in the present review to cover all processes in detail. Instead, the discussion will be concerned chiefly with typical processes embodying the advances that are most likely to be generally applied. ADVANCES IN GASIFICATION TECHNOLOGY For purposes of this discussion the starting point will be the conventional processes that were used for many years for the complete gasification of coal. These were: 1) carbonization in coke ovens followed by gasification of coke with air and steam in cyclic water-gas generators, and 2) fixed-bed air-blown producers. Both of these methods have obvious deficiencies when we consider that the ideal complete gasification process would be a single-stage, continuous

Jan 1, 1961

By F. W. Bowdish

A theoretical and experimental laboratory study has shown that the rate of breaking of oversized particles in a ball mill is proportional to 1) the concentration of such particles, and 2) the area of the balls, provided that the balls are larger than a certain size relative to the particles. If all undersized material were removed as formed, the rate of breaking would be almost independent of the quantity in the mill. Rate equations are given which are similar to those for zero, first, and second order reactions. Deviations of small balls from the equation for a second order phenomena are quantified by a factor called "nipping efficiency." Some data are correlated by a dimension-less equation, which is used to estimate nipping efficiencies from data not in the correlation. The investigation described here was undertaken after a literature survey revealed that little was known concerning the mechanism of breaking of particles within a ball mill and the effect of this mechanism upon grinding rates. One paper, by Roberts1 , offered a theory concerning the mechanism of breaking, and a rate equation for the breaking of particles larger than some size to particles smaller than that size. That paper provided the starting point for a theoretical and experimental investigation of grinding under carefully controlled conditions. THEORETICAL CONSIDERATIONS In his paper on the probability theory of ball mill grinding, Roberts theorized that "... a given expenditure of power leads either to a certain number of point to point blows per bp-hr or to a certain distance of line contact per hp-hr ..." He assumed that the balls touch each other during each blow or during moving contact. Then he said that a volume of pulp, dependent upon the size being considered, would be covered per minute within which all oversized particles would be crushed to particles smaller than that size. Naturally, the higher the concentration of oversized particles in the pulp, the higher the rate of which they would be broken. From this reasoning Roberts obtained the differential equation -dC/dt = k hp/ton C (1) where k is a constant for any size of particle, density of particle, and moisture content of pulp. C is the percentage of oversize in the material to be ground, t is the time, and hp/ton is the power input per ton of material in the mill. He then integrated the equation to log Co/Ct = k/2.3 hp/ton t , where Co and Ct are the percentage of oversize at time zero and t respectively. By always using the same quantity of material in a mill and assuming that it required constant power to run the mill, he was able to combine the horsepower per ton factor with the other constants to give an equation for a first order rate.

Jan 1, 1961

By C. E. Hennig

On January 1, 1961 there were 311 petroleum refineries in the United States with a total crude-oil throughput capacity of slightly more than 10 million barrels per day, according to the Bureau of Mines' annual survey. Compared with a year ago, this represents net increases of one in the number of plants and 109 thousand barrels per day in total capacity. Contributing to this increase was the completion of two new plants, one in Hawaii and another in Michigan, during the year. At the beginning of 1961 the industry was building facilities which will increase this overall crude capacity by 36,500 barrels per day. As part of its building program, it was also replacing 329,000 barrels per day of its present capacity. Of the total 10 million barrel per day installed capacity, the industry reported 380,000 barrels per day as being shut-down on January 1, 1961. This included 11,500 barrels per day considered inoperable without extensive reconditioning.

Jan 1, 1961

By A. W. Asman

The problem of balanced design in a belt conveyor has been under constant study. Increased use of this method of transport in recent years has stimulated investigations. Conveyor belt, power transmission and other machinery should be adequate to perform the required service. All components of the belt conveyor should work as an efficient unit moving its load continuously between terminals. As part of a long term research project on belt conveyors, Hewitt-Robins established in 1954 a 2-year grant at Pennsylvania State University. Under terms of the grant, certain fundamental phenomena were to be studied. This work evolved a new concept in belt conveyor power determination based on the principle of belt tension. The Penn State contract furnished the foundation for later more detailed studies. From these most recent investigations, more specific factors were defined. In the final analysis, all of the data collected has been worthwhile in belt conveyor design. Units now operate over long distances at speeds of over 800 fpm. Long high lifts are commonplace. Where vertical or inclined shafts were the rule, belt conveyors receive first consideration. Although belt conveyors have moved forward rapidly, the future will see a tremendous gain in their use. The ideal test belt conveyor would be several thousand feet in length and have a maximum tension of at least 70,000 lb., Also, this conveyor should be horizontai and have a variable feed rate of more than one material. Data from such a field belt conveyor combined with laboratory information would permit accurate analysis. Since this type of conveyor was not available, many field locations were visited: An alternate would have been to erect a closed circuit system in the laboratory. Either method had limitations and the first was selected as having the best possibilities. Manufacturers of conveyor belting and machinery basically have been using the same horsepower formula. As more information became available from field installations, factors in the basic formula were modified. Practically all conveyors are designed today by adding together the horsepowers required to move the empty belt, move the load horizontally, and elevate the load. In selecting size of drive motor, the first two elements are relatively unimportant if the last is large. However, it is the combination of

Jan 1, 1961

By O. E. Palasvirta

Several drum-type, low-intensity dry magnetic separators have recently been described 1,2,3,4 all of which share at least two generic similarities. The magnet consists of a multiplicity of poles of alternating polarity and, the speed of the drum shell, relatiw to the magnet, is such that the magnetics are agitated through rotation of the magnetic particles around their individual axes. The speed of the drum relative to the magnet (differential speed) determines the frequency of the field reversals. For effective agitation this frequency generally has to be above a specific value, which varies according to the mean particle size of the magnetics. With separators of small diameter, say less than 11/2 ft., a sufficient differential speed for treatment of fine magnetite can be attained only by rotating both the magnet and the drum separately; separators of large diameter may attain sufficiently high differential speeds with stationary magnets. Separators of large diameter thus have the advantage of simplicity of design. The capacity of a separator of this type is directly proportional to the speed of the shell. As the centrifugal force opposing the magnetic force increases at a slower rate than the peripheral speed of the shell when drum diameter is increased, large drums can be operated with higher peripheral speeds. Thus they have a higher capacity than smaller drums. Separation is also a statistical phenomenon, i.e. the grade of concentrate improves as the number of agitations or rotations of the magnetic particles per separation increases. As separators of large diameter have space for a large number of magnets they are best suited for production of optimum grade concentrate. The statements above are general clues For separator design. In the following an expression IS derived showing a more exact relationship between the pertinent separator variables. As both magnetic attraction and centrifugal forces are directly proportional to the volume of the affected bodies, complications in mathematical analysis, arising from variable particle size, are avoided by considering the force per unit volume of affected material. For the magnetic force per unit volume Runolinna (3) gives the following equation: V " 1 + N(ur, - 1) uo dr (1) where ur and uo stand for the relative permeability and the permeability of vacuum, respectively, N is the demagnetization factor, B the intensity of the magnetic field, and r the distance from the face of the magnetic pole. The permeability of a specific magnetite ore can generally be considered as a constant. For ground, liberated material N can also be treated as a constant, and the first simplification can be made by writing ur-1 1=k1. 1 + N(ur - 1) uD k1. Fig. 1 shows the field intensity curves for two U-magnets of different size, but of roughly similar geometry of cross-section as plotted against the distance from the plane of the pole faces. The curves

Jan 1, 1961

This Institute, by nature of its charter, draws on various persons in the mining and metallurgical world of Australasia for its President from year to year, and consequently when the presidential address is given by one of these people the topic. which they generally select is a topic to which they are accustomed and on which they are able to speak with authority.As most of you know, my prime object in life has been concerned with steelmaking, so tonight you can steel yourself to the thought that you are going to be spoken to about steelmaking.Even if that were not the case, and were I not particularly interested in steelmaking, I think it would be appropriate to look at steelmaking in a broad sense on a basis of pure metallurgical interest, because the steel industry is going through as big a revolution today as it went through something over one hundred years ago when Bessemer made a theory become a fact.Bessemer, and as the Americans prefer to think Kelly, separately conceived the idea of blowing cold air through molten pig iron, and, contrary to the then general belief, this did not result in cooling of the metal but succeeded rather in heating it, and in burning out of the rather crude pig iron the impurities which prevented it from becoming a ductile metal.For many years before this, steel had been made in a very small painstaking way by what was known as the crucible process. Benjamin Huntsman is credited with having developed the crucible steel making process to a stage where it could make a reliable and trustworthy product, but he...

Jan 1, 1961

By J. A. Berger, R. J. Towner

The pjPocesses of polygonization and subgrain growth were followed in slightly stretched 99.99 pct A1 single crystals heated for cumulative times at 400°, 500°, and 600°C. Changes in sub-grain size and boundary angle were determined from measurements on X-ray micrographs. CAHN1, 2 studied polygonization in stretched and heated aluminum single crystals of 99.99 pct A1 using various techniques, including etch pits, Laue patterns, and a slight restretching of heated specimens to reveal small changes in lattice orientation by the direction of new slip lines. He found that kink bands, which had well-defined boundaries lying in a plane perpendicular to the slip direction (at least in the early stages of deformation), formed during stretching. Also, he noted that bending occurred about the <211> axis lying in the (111) slip plane perpendicular to the <110> slip direction. His studies of polygonization were largely confined to the kink bands rather than to the weakly bent matrix regions between bands. The minimum temperature required to bring about polygonization was established at about 450 "C. Guinier and Tenevin used a focusing Laue X-ray diffraction technique to study polygonization in aluminum single-crystal specimens of 99.99 pct purity. Stretching the crystals 5 pct in tension caused a widening of the focused Laue spots. After heating for 4 hr at 450°C, their method revealed no change in the specimen. Above 450°C polygonization was detected and further annealing near 600°C led to subgrain growth. They concluded that the orientation of the crystal relative to the axis of deformation had no marked effect on polygonization. Gay and Honey-combe4 using an X-ray microbeam technique found that polygonization did not occur in a stretched aluminum crystal heated at 250oC, although some decrease in the yield strength occurred. When the temperature was raised to 475oC, the asterism became broken up as a result of polygonization. Honeycombe5 noted that reflections on X-ray mi-

Jan 1, 1961

By U. N. Bhrany, N. Arbiter

Over the last one hundred years the problem of assessing the efficiency of energy consumption in producing rock breakage has been studied by many investigators from a variety of viewpoints. Their contributions fall into three main categories: (1) those characterized by a priori assumptions of a relation between the energy required for fracture and the degree of fragmentation produced (e.g. Rittinged(l), Kick(2) Bond(3)); (2) those studying simple systems with controlled energy applications (Gross(4)?(5) ); (3) those treating operating data to develop practical relative measures of efficiency (Coghill(6), Taggart(7)). Closely involved in the efficiency problem is the characterization of size distributions produced by comminution. Unless an experimental size distribution can be approximated by a distribution function and its constants, it becomes difficult if not impossible to develop quantitative energy-particle size relationships. While many such functions have been proposed, none are both completely adequate and convenient. The simpler fonns usually describe only a part of the sizing data, while those which apply to a greater extent are cumbersome(8). The thesis underlying the study here reported can be stated as follows: Size reduction in a tumbling mill subjects ore particles to a relatively constant fracture-producing environment. The intensity of the forces is determined by such factors as the mass of the breaking bodies (rods, balls, rock), and the speed and dimensions of the shell. For a particular ore the extent of size reduction will depend both on the intensity and on the duration of exposure. The latter is the residence time in a batch mill, or is determined by the effective volume and the flow rate in a continuous mill. Size reduction can thus be regarded as a rate process in which the weight of material in size intervals varies as a function of grinding time. Although both the rates of disappearance of coarser sizes and

Jan 1, 1961

By Odin Wilhelmy

Agriculture in the United States today is becoming more and more a business, rather than a way of life. In the light of this, it behooves the farm-supply industries that provide the American farmer with his tools of production--feed, fertilizer, machinery, and the like--to give even greater attention than they have in the past to meeting the needs of the farmer-businessmen they are serving. Increasing competition among the companies that make up these industries merely accentuates this need for better service. An opportunity for such improved service, not yet fully realized, exists in the fertilizer industry today. That opportunity lies in the increased transportation of fertilizer ingredients by water. However, before the benefits inherent in this increased water movement of fertilizers can be fully realized, certain obstacles must be met and overcome. It is the purpose of this paper to outline the nature and magnitude of this opportunity, to point out some of the roadblocks and the steps that can be, or are being, taken to remove them, and to indicate some of the rewards that would logically stem from success in these efforts.

Jan 1, 1961

By M. A. Hammer

In this study by the Federal Bureau of Mines Pennsylvania anthracite from the Eastern Middle field was oxidized by concentrated nitric acid at steam-bath temperature for 24 to 1,000 hours. The quantitative data obtained include yields of nitric-acid soluble and insoluble products and the distribution of carbon and ash in each. The acid-insoluble residues were examined for solubility in aqueous sodium hydroxide. With a sodium hydroxide concentration of at least 1 normal, a portion of the residue could be extracted in the form of a true solution. With lower alkali concentrations, peptization occurred. Alkali solubility of the residue increased with length of oxidation. However, when expressed in percentages of original coal weight, the alkali solubility remained essentially constant after 192 hours of oxidation. This suggests that the alkali-soluble products are converted to acid-soluble products at the same rate as the original coal substance is converted to alkali-soluble material. Microscopic observations of the peptization of the acid-insoluble residues revealed a gross micellar physical structure. The action of nitric acid is apparently not restricted to the surface of a coal particle. The acid penetrates the particle through the pore structure, dissolving some of the ash and altering the bonds between the coal micelles. The bond alteration, as indicated by ultimate analyses, involves the physical and chemical adsorption of the components of nitric acid. Some of the altered bonds are not thermally stable; this instability is shown by the complete loss of peptizing ability when the acid-insoluble products are heated above 200° C. This loss is accompanied by the evolution of water, oxides of nitrogen, and hydrocyanic acid.

Jan 1, 1961

By L. A. Updegraff

Before discussing the application of capacitance for the measurement of moisture content in a moving stream of coal it might be well to first give a brief description of the process and then show how it can be applied to the coal industry. A capacitor may be described as a device having two conductors separated by an insulator, the conductors hereafter being designated as a test cell or test plates and the insulator as the dielectric. Capacitance, therefore, is a measure of the ability of a capacitor to store an electrical charge. Two basic factors that affect capacitance are the dimensions of the capacitor and the dielectric constant of the insulator. Capacitor dimensions which affect its capacity are the area A of the conductive surface, and the distance d between plates. Capacitance is inversely proportional to the distance between plates and directly proportional to area A, so if capacitance is indicated as C and the dielectric constant as K the equation for capacitance would be C = AK/d. The dielectric constant can be described as the ratio of the actual capacitance of any given material to that of a vacuum, which is unity. In industrial applications the area of the plates remains constant as also does the distance between them, leaving the dielectric constant as the only variable to affect the capacitance measurement. Figure 1 is a schematic diagram of an r-f excited capacitance bridge in which a test cell is part of the circuit. This bridge consists of four capacitors in two pairs connected across an a-c voltage source. In one side of the circuit the two capacitors are fixed but in the other side they are variable, one being the rebalance capacitor operated by the servo motor and the other the test plates between which the dielectric passes. Capacity of the plates is a function of the dielectric constant of the material between them and is measured at radio frequency. Within the recording instrument is an r-f oscillator and a 60 c ps modulator. The radio frequency signal is generated by the oscillator, modulated by a 60 cps wave, and sent to the bridge. Therefore the signal entering the capacitive bridge is a radio frequency carrier with a 60 cycle envelope, If the bridge is in balance as the signal enters there would be no voltage drop and so no output by the detector. As long as the dielectric constant remains the same the bridge will stay in balance. However, any change in the dielectric constant, which in this case would be a change in moisture content, would affect the bridge. Higher moisture increases the capacity of the test cell which causes less voltage to develop across it causing imbalance of the bridge. This in turn causes a radio frequency signal to appear at the detector. Output from the detector is a 60 cycle ripple which is in proportion to the imbalance of the circuit. A 60 cycle amplifier boosts the detector signal to enough power to drive the servo motor which positions the recording pen and also rotates the variable capacitor, to which it is mechanically connected, to bring the bridge back in balance. An increase in moisture causes the servo motor to rotate in one direction, but a decrease causes imbalance in the opposite direction, and thus rotates the motor in that direction. This brings the bridge back in balance and stops the motor. The bridge shown in Figure 1 has been modified so as to provide a wide range of adjustments. Coarse and fine span adjustments located in the recording instrument are set to govern the amount of pen movement for a given change in capacitance. A measuring head unit contains coarse and fine zero adjustments for

Jan 1, 1961

By H. B. Charmbury, D. R. Mitchell

Everyone in the coal industry from top management to the preparation engineer is vitally interterested in recovering as much salable coal as possible from the run-of-mine product. Coal losses from a preparation plant occur in the solid refuse material being discharged from the plant and in the bleed-off slurry from the water circuit. The refuse is generally hauled from the plant in solid form by trucks, conveyors, or aerial trams to the refuse or culm banks or it may be crushed and transported by hydraulic methods to refuse ponds or dams. The loss of coal in refuse material and the extent of this problem has been covered in another paver.&apos; The loss of salable coal in the plant bleed-off slurry is one of the water circuit problems in coal preparation plants. Slurries originate at various places in the processing circuits and are usually disposed of by transportation to waste ponds known as slurry ponds. Even though the combustible material discharged as slurry and refuse from the plant is labeled a loss, the loss must only be considered temporary. There is a tendency at the present time to examine refuse and slurry losses and to reprocess these materials to recover valuable coal. Slurries from eight bituminous coal preparation plants in central and western Pennsylvania have been sampled and examined to determine the amount of recoverable coal in each. Examinations of the samples were made to determine the tons per hour of solids and the gallons per minute of water in the slurry; the size, ash, and sulfur analyses of the solids; and the sink-float characteristics of the larger solids. The extreme fines (—325 mesh material) from one of the samples has been examined further to determine the micron size fractions as well as the ash and sulfur content of the micron sizes. Collection of the Samples: Field trips were made to each of the plants where samples were obtained and discussions held with the preparation engineer prior to sampling. The flowsheet of the plant operation was studied and a time-period selected to obtain a representative sample. At least 20 1-gal samples of total plant bleed-off suspensions were collected at each plant in increments over designated periods belived to be typical of the plant flow Three of the samples were obtained from plants in the Pittsburgh area. Each plant supplied information on the capacity, operating time, type of cleaning equipment used, water and material balances, and auxiliary equipment. From the time required to collect given amounts of slurry and from the amount of solids in the slurry, total solids discharges from the plant were calculated and compared with the plant flow. Ash and sulfur analyses of the total solids were also checked, at some plants, with company figures. In all cases where checks could be made there was reasonable agreement between company figures and those reported here. Analysis of the Slurries: Representative fractions of properly agitated samples were examined in the laboratory to determine the specific gravities of the slurries. The solids and water were separated by filtration to check the weight of each so that the percent of solids in the pulp could be determined. From the resulting data, presented in Table I, it may be seen that the percent solids in the slurries ranges from 2.8 to 39.0 and the amount of solids from 2.61 to 45.61 tph. Size Analysis of Solids: Representative fractions of the slurries were permitted to settle and the clear water was removed by siphoning. The solids were then wet-screened at 28, 35, 48, 65, 100, 150, 200 and 325 mesh. Results of the size analyses are presented in Table 11. These results indicate the extreme variation of sizes and in most cases the degree of fineness of the solids. The amount of —325 mesh ranges from 22.5 to 84.5 pct and the amount of+200 mesh from 8.3 to 69.1 pct.

Jan 1, 1961

By D. H. Trollope

In engineering in general, close agreement between theoretical predictions and structural performance is rare—this is particularly true in rock slopes. Since the complexity of natural arrangements makes exact theoretical solutions of associated structural problems almost impossible, the role of theory should be that of developing guides or markers to which observations and experience can be related. The author in this paper has outlined the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Some important practical considerations result—especially in regard to horizontal stresses—when theory is compared with full-scale experience. In the field of engineering activity, specific examples of close agreement between theoretical prediction and structural performance are rare. Particularly is this so for the case of rock slopes, where, owing to the complexity of the natural arrangements, it is quixotic to expect exact theoretical solutions to the associated structural problems. The role of theory is rather that of developing signposts or guide rails to which observations and experience can be related. It is with this in mind that the present paper has been prepared; the author&apos;s aim has been to set out briefly the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Despite the idealization of the problem, it will be seen that the theoretical conclusions are in accord with full-scale experience, particularly as far as horizontal stresses are concerned, and they point to some important practical considerations. CLASSIFICATION OF ROCK SLOPES At the risk of over-simplification, an attempt has been made to classify the problem of rock slopes into three broad categories with respect to internal stress systems. These are illustrated in Fig. 1. It is tacitly assumed in this classification that the strength of individual particles is very much greater than the interparticle strength whether the particles are the crystals of an igneous rock (Case I) or the blocks of Cases 2 and 3. The Homogeneous Monolith: This case is representative of uniform unjointed rock. Under relatively low stress conditions the internal stress system may approximate to that of an elastic body as given by Terzaghi.&apos; It is more usual, however, for overall stability, to consider the material as a rigid plastic which yields in shear when S =C + c tan 4> where S is the shear yield stress, o is the normal stress on the surface of failure, and C and d are empirical constants according to the Mohr-Coulomb criterion of failure. Sokolovsky has recently developed, for the first time, a series of mathematical solutions to problems involvinga C, mass subject to self-weight. He demonstrates that for such a case a semi-arch (Fig. 2) is stable. A corollary of this argument is that for a true C, d material a curved overhanging slope is possible and such an observation may well aid field identification of these materials. The shape of the curved slope face is however directly dependent on the C-value, and from the long-term point of view this is a most difficult value to establish with any degree of confidence. It is customary to measure C and 0 in some form of shear test—usually a triaxial compression test—on core specimens sampled from the rock, and as far as the author is aware the present case is the only one in which, as far as overall stability is concerned, such tests are

Jan 1, 1961

The coalmining industry in most countries has, at various times, suddenly been confronted with a decrease in demand for coal. Readjustments made to reduce productive capacity to match the reduced demand for coal have often resulted in hardship to mineworkers, loss of capital investment to mineowners and loss of coal reserves. The consequences of the methods of readjustment adopted in the past have contributed to the low esteem in which coalmining has come to be regarded by a large section of the gel).eral public in many countries.Four sections of the coalmining industry, representing different periods of time, different countries, and different methods of industrial organisation have been examined:Great Britain and the U.S.A. during the inter war years, the post war European Coal and Steel Community, and post war Great Britain under the National Coal Board. An assessment has been made of the methods adopted in each case to reduce productive capacity to match a reduced demand for coal. Finally the fundamentals of the problem-as it affects the coalmining industry of any country-are considered, and possible solutions put forward.During the 1950&apos;s, surplus productive capacity was a problem in many coalmining countries, including Australia and New Zealand. As a rule no techniques are developed beforehand to solve problems introduced by a sudden decrease in demand for coal. The situation is usually tackled by a series of short term decisions based on expediency, which often in the long run only aggravate the problem.

Jan 1, 1961

By P. G. Hallof

Only recently has the term Induced Polarization found its way into geophysical literature. Schlumberger first mentioned the possible use of the induced polarization effect in one of his early papers. Later, induced polarization was the subject of several university theses, such as Seigel&apos;s at the University of Toronto and Bliel&apos;s at the Michigan School of Technology. In addition, a group at the New Mexico School of Mining and Technobgy has done work on induced polarization. There is very little to be found in print on the subject of induced polarization. Several papers have been presented at meetings, the 1958 AIME and SEG* conventions, for instance, on laboratory measurements of the effect and theoretical considerations useful in the interpretation of field results. This paper is the first attempt to present actual field results which show the usefulness of induced polarization as a prospecting technique. There are several phenomena that can cause polarization when electrical current is passed through the ground. In a paper presented at the 1958 SEG* meetings Professor T. R. Madden of M. I. T. demonstrated that only two of these gave rise to appreciable effects. The first is a result of the membrane and diffusion effects in a sandstone that contains appre- ciable amounts of clay minerals. The unbonded charges associated with the clay mineral forma material that passes positive and negative ions with different mobilities. When current is passed through such a system for some period of time, polarization results. The second phenomenon, which gives rise to very much larger polarization effects, is the one used in the new prospecting technique. These effects are a result of the blocking action or polarization of metallic or electronic conductors in a medium of ionic solution conduction. This electrochemical polarization, called "the over-voltage effect" by electro-chemists, occurs whenever electrical current is passed through a volume of rock which contains metallic minerals such as base metal sulphides. This polarization at metallic interfaces in ionic solutions depends upon the chemical energies necessary to allow the ions to continue the flow of current by giving up or receiving an electron from the metallic surfaces. The energy stored in this reaction isanalogous to that stored when a condenser is charged. If a d. c. current flowing through such a system is interrupted, the polarization can be detected as a small, decaying current that flows after the applied current is discontinued. The decaying potential measured is a result of the current flow caused by charges returning to their equilibrium positions from the positions they assumed under the applied potential field. Because of the polarization, there is an excess of change at each metallic interface. There is an alternate method of measurement of the induced polarization effect. The electrical

Jan 1, 1961

By J. C. Osmond

One of the least known geologic regions in the U.S. is the area now called the Basin and Range Province. It is paradoxical that so little geologic information has been compiled for a province that has yielded billions of dollars worth of metals and is currently producing a small amount of oil. Regional stratigraphic studies of parts of this large territory have been published only recently, and regional structural interpretations of even parts of the province are rare in the literature. This, of course, does great injustice to the earliest workers: Gilbert,1,2 Russell,9 Le Conte,4 Spurr,5 Louderback,8 and others, who recognized the area as distinctively different from the rest of North America. Their simplified picture of the structure of the ranges and the province as a whole is the groundwork for present understanding and has never been superseded. Since their early works, however, geologic data from the province has consisted largely of detailed reports of widely scattered mining districts. Each district has been described as though it were an island in an unknown sea. More recent syntheses of the geologic history have been prepared by Lindgren,7 Ransome,8 Nolan,9 Bill-ingsley and Locke,30 Longwell,11 and Eardley.12 The tentative nature of the present interpretation, which treats the structural evolution of the Utah and Nevada area, must be considered in light of the scarcity of geologic information from the province as a whole. The methods of interpreting tectonic history from stratigraphy are based largely on the concepts of Marshal Kay.23 Discussions with Hoover Mackin also have aided in organizing the Tertiary history. TECTONIC AND STRATIGRAPHIC SETTING Two approaches to the subject of the tectonic history are possible; they correspond to looking through opposite ends of a pair of binoculars. One involves an expansion and extension of detailed work and the other an interpretation based on regional geological relationships. It is believed that the second approach, used here, is not in disagreement with detailed observations. The area of the Basin and Range Province is shown in Fig. 1. Within this area middle Tertiary to Recent high-angle faulting has controlled development of mountain ranges and valleys. Only the part of the area north of Las Vegas, Nev., and south of the Snake River in Idaho will be considered in this article. Within this part of the province most of the ranges trend north-south. Approximately two thirds of the area is covered by late Tertiary to Recent valley fill and lake deposits.

Jan 1, 1961

By J. W. MacDonald

Review of equipment, performance, and shaft design plans including head-frames for sinking and forms for lining are given. Also included are comparative data for shafts of 11 x20 ft and 193/4 x 30 ft with 756 and 666-ft depths, respectively. Advantage from curtain wall installation with "slip forms" which warrant consideration for normal lining are outlined. A preliminary review is also made of "chemical grouting" to stop water inflow leakage with Halliburton equipment and service. Two coal mine shafts recently completed in Franklin County, Ill., afford experience and accomplishment to warrant review. These shafts provide access to a tract with a potential recovery of one hundred million tons. This work provided the initial sinking by other than a contractor&apos;s organization since 1918. Four additional shafts required during the interim were sunk under contract arrangement with others. Supervisory contact and inspection afforded experience to govern planning and conduct of the recent work. TEST DRILLING Core test holes were drilled within each of the two shaft locations. Four additional cable tool holes were drilled on a radius of 700 ft from the shaft bottom to determine the coal seam elevations and govern the underground layout plans for each shaft. A graphic log of the hoist shaft test drillhole is shown by Fig. 1. A very soft sandstone was found at a depth of 16 ft. Cored recovery of the sandstone proved much weaker than the overlying compacted sand secured with coring facilities for soil recovery. Gradation from the very soft sandstone to fairly hard material occurred with the next 14 ft, extending to a depth of 30 ft. The weak character within the upper portion entailed need of adequate protection when sinking as described later. A part of the sandstone provided sufficient porosity and permeability to warrant further investigation. Adjacent cable tool drilling for temporary water supply disclosed inflow was limited to 2 gpm with a depth of 40 ft. It was increased to 12 gpm during the next 50 ft of drilling and occasioned subsequent precaution when sinking. General arrangement of facilities for sinking the hoist shaft is shown by Fig. 2. An available steel frame building was used to accommodate the hoist, compressor, shop, and shower or change room. The stiff leg derrick with 90-ft length of boom permitted removal of forms from the wood shop to the storage area or delivery within the shaft. Reinforcing steel and other needs were similarly handled, in addition to headframe erection. The headframe was placed over one end of the shaft to enable passage of forms for lining through the adjacent half next to the stiff leg derrick. The steel headframe as shown by Fig. 3 was fabricated locally. Side anchored cables from the

Jan 1, 1961

By Richards S. M

The abundances and abundance relationships of lead, zinc, copper and silver in the major sulphide lenses at Broken Hill are examined, and their possible geochemical significance discussed.When expressed as atoms per cent, zinc is the most abundant base metal throughout the whole .group of orebodies, the highest average lead: zinc ratio (No. 2 lens) being about 0&#183;45, the lowest (No. 1 lensZinc Lode group) being in the 0&#183;12-0 &#183;14 range. Lead and silver are clearly higher in the lower two orebodies, but the abundance of zinc shows no apparent relationship with stratigraphical position. Among the base metals copper is conspicuously low and remarkably uniform, a feature noted in other conformable orebodies.Although, as has been recognised for many years, abundances of silver and lead, and lead and zinc, are sympathetically related, correlation within the pairs is variable and generally of low degree. Silver and lead show distinctly the better correlation, particularly in No. 3 lens. On the basis of lead: zinc ratios, No. 2&apos; and No. 3&#183; lenses, on the one hand, and the No. 1 lenses, Rhodonitic and Siliceous Zinc Lodes on the other, constitute two groups. However on the basis of silver : lead ratios, No. 3 lens stands alone, No. 2 lens showing clear affinities with the higher layers. Ternary relationships between copper-zinc-Iead and silver-zinc-Iead emphasize the very close constitutional relationship between the No. 1 lenses and the two &quot;zinc lodes&quot;.The possible implications of these relationships are then discussed in the light of the&apos; two principal theories-hydrothermal replacement or chemical sedimentation-held for the formation of the Broken Hill ores. It is pointed out that the ratios of the four metals in the ores are rather different from those found in most igneous and sedimentary rocks, and in seawater. For &apos;example, whereas copper and zinc are present in almost equal amounts in most terrestrial materials, copper in the ores is only about one-hundredth of the amount of zinc. Lead has increased somewhat, but the ratio of silver to lead has fallen; in spite of its recognition as a source of silver, the Broken Hill lode is impoverished in silver with respect to lead as compared with most common terrestrial materials.No solutions are offered to these prob&apos;lems of abundance. Rather it has been the aim of the work to provide data, and to demonstrate the...

Jan 1, 1961

By J. W. Mills

In 1956 the discovery of nickel on Jumbo Mountain, Snohomish County, Washington, focused attention on this part of the Cascade Range, far more renowned for its timber than for its mineral resources. Hand specimens assaying as high as 13 pct Ni encouraged Discovery Mines Inc. of Mount Vernon, Wash., to stake 12 claims in Township 31 North, Range 9 East of the Willamette Meridian. The property was leased to Climax Molybdenum Co. in January 1957. Trenching, sampling, and geologic studies were carried out during the late summer of 1957 when most of the snow had disappeared. Although the deposits are only about four miles south of the logging town of Darrington and about two miles. as the crow flies, southeast of the end of a good gravel road from that town, all camp supplies and equipment were air-dropped, owing to the extremely rugged nature of the terrain. GEOLOGY The rocks of Jumbo Mountain comprise a series of folded Tertiary sediments forming a belt one half to three quarters of a mile wide, trending northwest about parallel to the strike of the beds. This belt is sandwiched between two extensive in-trusives—gabbro on the northeast and quartz dio-rite on the southwest—and has been intruded by dikes of fresh and serpentinized dunite. Shear zones follow many of the dunite-sedimentary rock contacts, and in these the nickel mineralization is concentrated. A few transverse faults offset the sediments and ultrabasics. Sedimentary Rocks: Two kinds of quartzite make up the greater part of the sedimentary section. One is dark purplish gray, very fine-grained, and thin-bedded; the other is light gray to white, medium-grained, and well-bedded. Locally the light-colored quart lites contain grit and conglomerate horizons, rich in pebbles of white chert and very fine-grained quartzite. Intercalations of dark argillites near the summit of the mountain give many of the cliffs a striking banded appearance. Dark gray to black, aphanitic, thin-bedded argillites occur throughout the entire sedimentary belt. Beds vary from a few inches to a few tens of feet thick and some, near the summit, contain numerous fossile (willow?) leaves. Only the thicker beds were mapped. The sediments are quite fresh on the northeastern side of the belt and become more metamorphosed (hornfelsed) toward the southwestern side. Brown biotite is present in the metasediments in increasing amounts as the quartz diorite is approached. Near the intrusion, porphyroblasts of plagioclase, up to 1 in. across, testify to the soaking of sedimentary rocks by solutions emanating from the quartz diorite. Most of the sediments mapped lie along the southwestern limb of an anticline, the axis of which follows the crest of the mountain and plunges at a low angle to the northwest.

Jan 1, 1961