Search Documents

By G. W. Jones

In cooperation with the Edison Electric Illuminating Co. of Boston, Mass., and the Boston Consolidated Gas Co., a survey has been conducted continuously since 1929 by the Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes since May 1, 1933. Yearly reports6/ on the results obtained since the beginning of the survey have been published. The method and procedure of conducting the survey in 1936 were the same as heretofore.

Jan 1, 1938

By A. A. Millar

THE output of coal from the Province of Alberta reached its peak; in the year 1928, when 7,334,179 tons were produced. Following this, a steady decline was recorded, and in 1930 a low mark of 4,564, 290 tons was made. Since that time, however, the tendency has been upward, and this year (1937) 5,551,682 tons were produced, compared with 5,696, 375 tons in 1936 and 5,462,973 tons in 1935. The value of the output in 1937 was $14,434,969, against $14, 720,004 in 1936. The coals of Alberta have been classed under three heads, viz., domestic, sub-bituminous, and bituminous The domestic (or lignite) and the sub-bituminous coals are used chiefly for domestic purposes, with the possible exception of the smaller sizes and the output of the two stripping pits at Stereo and Coal Valley The bituminous output is used mainly by the railways, for locomotive purposes, which, in 1937, accounted for 80.6 per? cenr of the total sales of bituminous coal. A fair proportion is sold for stationary engine and steam purposes and, in 1937, 25,000 tons were used in making briquettes at plants operated by the Canmore Coal Company, Limited, and Brazeau Collieries, Limited. The International Coal & Coke Company, Limited, used 99,500 tons in their plant at Coleman, for making coke. The bulk of the 66,000 tons of coke produced was sold for use at the smelter at Trail, B.C.

Jan 1, 1938

By L. C. IlsLey

The increasing use of Diesel engines for operating equipment on trunk-line railroads and for power-plant units has stimulated interest in the use of Diesel engines for other lines of work, among which is the possibility of substituting Diesel locomotives for trolley locomotives for mines. The possibility of developing Diesel locomotives for duty in American mines is not as remote as it might seem, particularly in view of the fact that locomotives of this type are already used in considerable numbers in European mines. A study of Diesel locomotives in Europe is contained in Report of Investigations 3320, Diesel Mine Locomotives - Development and Use in European Coal Mines, by George S. Rice and F. E. Harris.

Jan 1, 1938

By S. H. Lorain

This paper is a preliminary report on recent lode gold mining activity, operating conditions, and mining and milling methods at properties in production in September 1936 in the gold belt of northeastern Oregon. A few inactive properties are described also. Districts, inactive in 1936, that have been important producers at some time in the past are mentioned briefly. This is one of a series of similar papers describing western mining districts. The past production record of the gold mines of northeastern Oregon entitles the region to be ranked as one of the important gold-mining regions of the United States. Although comparatively inactive for many years, lode mining in the region has recently undergone a marked revival.

Jan 1, 1938

Power Plant. The power for the metallurgical operations is supplied by the company's own power plant, which is centrally situated. Power is also supplied to Metal Manufactures Ltd. and Australian Fertilizers Ltd., both being adjacently situated to this company'sworks.The power supplied is direct current, 250 volts, and is obtained from direct-current generators coupled to turbines and to Belliss & Morcom triple expansion engines.The steam supply is obtained from Babcock & Wilcox water tubular boilers, the fuel used being drawn from the South Coast coal mines.Transport. - The works are connected by standard broad gauge railway to both the jetties and the Government railway. Two steam and three electric locomotives are employed in this service.In addition to its own requirements, transport is provided to Metal Manufactures Ltd. and Australian Fertilizers Ltd.The various operating departments are connected by a 2-ft. gauge railway operated by Jeffrey electric locomotives.Ore Storage and Sample Mill - These departments are connected by broad gauge line to the Government railway and jetties. All material which is railed or shipped to the works from the various centres is weighed, sampled and placed in the ore store, or outside gantries, before being treated.Since the whole of the material received is either purchased or treated on a toll charge, great care is necessary in the weighing and sampling of all the receipts.Assay Oflice--The assay office is divided into several laboratories, where analyses of the various purchased materials and works samples are carried out.

Jan 1, 1938

By Oliver Bowles

From the most remote periods of civilization, stone Las been used to perpetuate the memory of individuals or to immortalize their noble achievements. Ancient memorials ranged from simple piles of stone (cairns) or single markers to great obelisks and pyramid or magnificent mausoleums. The Taj Mahal at Agra, India, built of white marble by Shah Jehan in memory of the Empress Mumtaz Mahal, is one of the most beautiful and costly memorials ever built. It was erected between 1632 and 1050 at a cost estimated at a: high as $50,000,000, and it is today an object of unusual attraction for travelers. Other magnificent memorials, both ancient and modern, are to be found in many lands. Memorials of varying design have characterized the passing centuries and have found an important place in the New World. In early days, monuments were chiefly imported into America, but gradually an extensive memorial stone-manufacturing industry developed on this side of the Atlantic. Sales value of domestic memorials, f.o.b. quarry or mill, attained a maximum of $17,488,755 in 1920, and retail sales, of course, reached a much higher figure. Modest markers and tombstones are to be found in almost every rural community in the United States, and there are many elaborate and costly monuments in and near urban centers.

Jan 1, 1938

By Orr C. W

In previous papers (1, 2), the influence on the creep resistance of elements normally found in commercial lead has been recorded. The results in the present paper refer to the influence of calcium, an element which is not found naturally in lead, but which has been used commercially in the form of alloys. It was realised that calcium would act as a deoxidising agent for lead-and in fact it was with this feature in view that both calcium and magnesium were used as additions. Subsequent work (including the results given in the present paper) has tended to diminish the importance which at first seemed to be associated with the presence of oxygen in lead. The structure of the dilute calcium lead alloys has been worked out in detail (S) and the phase diagram shows the existence of limited solid solubility and a compound CaPbs.

Jan 1, 1938

By P. D. P. Hamilton

IT is perhaps obvious to most individuals who are interested in the mining industry that a producing mine has been subjected to several phases of engineering attention. In this paper it is the author's hope that a thoughtful survey of these various engineering phases will emphasize certain points of value and interest which may sometimes be overlooked. The points which we will bring out are being made in an analytical sense and are not in any way a reflection on any individuals or organizations which might see in these illustrations a similarity co chair particular conditions. In other words, we are drawing on our general experience to illustrate the points which we chink are worthy of mention, and which we believe are of a type sufficiently frequent co be emphasized. It is well co point out chat, in this paper, we are not concerned with the relative importance of such theoretical questions as to whether or not a geologisc is more important than a prospector, or the office manager than the surface foreman. We are, however, interested in analyzing the various types of engineering experience required in the bringing of a mining enter-prise from the early prospect stage in co-production, and their importance to the project as a whole. In order to simplify our analysis of the subject, it has seemed best to outline a simple mining organization. In using the terms 'industry' and 'business', we feel chat frequently those engaged in mining do not always appreciate that mining is actually an endeavour, or a business, which has the same economic fundamentals as any other business. In the mining industry, the field and producing engineering are counter-parts of the research and production phases of any other type of business. Once this is realized, it is fairly obvious that mining, like any other industry, is a matter of economically acquiring raw materials, processing them, and finally marketing the resultant commodities as favourably as possible. The points may be discussed in a little more detail as follows.

Jan 1, 1938

By S. M. Shelton

Preliminary work in the investigation of electrolytic manganese, as reported4/, showed promise for a practical procedure of continuous production. Laboratory work was continued in the direction of process simpliication to determine an economically feasible procedure that would require a minimum of expensive equipment for plant erection and a minimum of reagent consumption for operation. Results furnished enough evidence to indicate that modifications of the process could be made leading to simplified procedure and with no sacrifice in operating efficiency. A supply of at least 200 pounds of the metal was desired for alloy research, and it was believed worth while to utilize available facilities in a search for difficulties that were not encountered in the laboratory and that might arise in larger-scale operation. Consequently, an experimental pilot plant was erected. The plant was designed for a capacity of 15 pounds per day of metal and operated under simulated plant practice.

Jan 1, 1938

By Oliver Bowles

Marble is one of tile most beautiful and enduring materials employed in the construction industries. Because of its diverse colors, decorative patterns, and varying textures, it has furnished material for artistic architectural design for many centuries. The marble industry is described in some detail in Bureau of Mines Bulletin 106, The Technology of Marble Quarrying, which, unfortunately, is now out of print but may be consul ted at most large libraries. Onyx marble and travertine are discussed in Bureau of Mines Information Circular 6751. The purpose of this paper is to describe the main features of a distinctive group of ornamental marbles known as the serpentine marbles or verde antiques.

Jan 1, 1938

By Walter B. Lenhart

This paper is one of a series on milling methods and costs being. published by the Bureau of Mines. The milling practices and special problems relating to grinding, tailings disposal, and choice of a treatment process at the Cardinal mill are discussed. The property of the Cardinal Gold Mining Co. is about 18 miles southwest of the town of Bishop, Inyo County, Calif., at an altitude of approximately 8,500 feet. The camp has been designated Bishop Creek by the postal authorities. The property comprises 33 mining claims, including fractions and millsite in sections 19, 20, 29, and 30, T. 8 S., R. 31 E. These claims are located in a general way along the strike of a band of quartzite.

Jan 1, 1938

In the interest of safety in underground coal mining, the Bureau of Mines recommends: 1. That doors used to control ventilation (a) Shall be installed in pairs to form air locks, (b) Shall be self-closing, (c) Shall not have latches or other devices for holding them open, (d) Shall be constructed and maintained to prevent excessive air leakage through or around them, (e) Shall be fire resistant. 2. That wherever practicable the use of doors shall be limited to development openings. The Mine Safety Board is of the opinion that the best practice in coal-mine ventilation makes use of a split system employing overcasts or undercasts with doors limited as far as feasible to development openings. The distance between air-lock doors on haulageways should be sufficient to accommodate a trip or train of maximum length. Where auxiliary doors are installed to control ventilation during emergencies, they should be so placed that they can be utilized readily in case of damage to the air-lock doors.

Jan 1, 1938

By William O. Vanderburg

This paper gives the results of a reconnaissance of the mining districts in Humboldt County, Nev., made during the month of June, 19373/. During the field work, virtually all the mining districts in the county were visited and many data were obtained on a number of active and inactive properties. No attempt has boon made to include in this report all the properties in the various mining districts, and it should be emphasized that whether or not a property is mentioned herein has no being on its merit. The report covers the location of the various mining; districts, types of deposit, information on past operations and current activity, and general information likely to be useful to operators, investors, and others interested in mining. The geology of the deposits is discussed only briefly. The names of the various mining districts mentioned in this report are those generally used when they were organized for purposes of record and regulation. As organized, the districts embraced largo areas with no definite boundaries, and the names have little significance.

Jan 1, 1938

By J. R. Thoenen

In Progress Report 1,4/ a number of facto mere demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

By G. B. Gould

Every mathematical statement of a measure of anything (as distinguished from a count') is followed by a qualification—always implied if not explicity stated—-that the statement is only an estimate, which may vary from absolute accuracy within certain limits, according to the accuracy of the measuring instrument. This basic fact, so obvious to engineers, is not so well understood by many that make use of laboratory coal tests. The tolerances that must be allowed in measurements of coal quality are very important in both their commercial and engineering applications—and the significance of these tolerances depends upon the use made of the laboratory coal test. Only in recent years has there been any intensive study of this question of tolerances as applied to measurements of coal quality. There is very little in our published literature on the subject, and what has been published is not readily comprehended by those who sell coal, or buy coal and use it, unless they happen to have made a study of the subject themselves. There is great need for more widespread understanding of what lias been discovered and how it applies to the use of laboratory coal tests. What follows is an attempt to condense into a few pages the results of the major investigations so far reported, and to explain their meaning in simple nontechnical language, with the addition of some recent illustrative experiments. Determining Deviations in Quality It is necessary at the outset to distinguish between: (I) the accuracy with which one test indicates the quality on one lot of coal; and (2) the accuracy with which a test of one lot of coal represents the average quality of a commercial product, of which the buyer will presumably receive a series of shipments—perhaps many thousands of tons. It is necessary to make this distinction because coal is a variable material—a heterogeneous mixture of a variety of components—the quality of which will vary from one lot to another. Therefore an absolutely accurate determination of the quality (if that were possible) of one lot of a coal is an

Jan 1, 1938

By O. H. Metzger

This is one of a series of papers on placer mining in the western United States. The author has endeavored to give a general outline of the available placer deposits in Boise County, Idaho, together with a description of current practices and the recovery costs of the principal producers. The paper is based on a field examination by the author in May and June 1937. Boise County (fig. 1) is in the southwestern part of Idaho. It has a maximum length of 60 miles, a maximum width of 42 miles, and an area of approximately 1,600 square miles.

Jan 1, 1938

By Mann V. I

The Mount Isa property has been in operation since June, 1931; during this period operations have changed from the production and treatment of carbonate ores to the mining, milling, and smelting of sulphide ores. This change involved revision of ore-extraction methods.Stoping methods have been designed to apply to parallel lodes ranging from 10 ft. to over 100 ft. in width and dipping at 50° to 60°. The hardness and strength of the ore and enclosing wall rocks, together with the strength and thickness of the country rock between lodes, have permitted the selection of a sub-level stoping method for mining the sulphide ores.

Jan 1, 1938

By Paul M. Tyler

A great variety of substance that differ widely in chemical, mineralogical, and physical properties are loosely linked under the generic term "clay", but for the average man all that matters is whether a given material can be sold or used profitably. So-called "clays" range in texture from true clays and allied minerals that are typically "fat" or sticky to fine sand. Sand and other strictly silicious materials, such as tripoli and diatomite, are not clays in any sense; but many commercial clays are strictly loams, for they are intermediate in texture and always contain a mixture of minerals, though the term "loam" has little commercial usage except in foundry work. Even pure kaolinite, ordinarily considered the typical "clay substance", recently was found to exist as three distinct minerals; and each of these, in turn, exhibits variations in particle size and other physical attributes. Probing with the X-ray and employing other modern tools and techniques, scientists are tracing the patterns of molecules and finding chemical and physical phenomena that seem to disclose the causes for the markedly different behavior of the various aluminum silicates with varying proportions of combined and adsorbed water that are the essential ingredients of commercial clays; but rule-of-thumb definitions and enforced reliance upon empirical tests of actual samples still hold sway. In addition to the hydrated simple silicates of aluminum, almost all clays contain quartz, feldspar, and mica with varying amounts of organic matter and, in addition, other impurities - such as iron, manganese, and titanium oxides - that may discolor them sufficiently to render them unfit for certain important uses. The white clays are generally the purest, but no two clays are really alike, and great care must be exercised to maintain a reasonable uniformity in successive shipments even from the same deposit.

Jan 1, 1938

By J. M. Cummings

CONSIPERABLE information on the industrial or non-metallic mineral resources of British Columbia has been published. For a general resume of the subject, reference may be made to a paper presented by A. M. Richmond before the Annual General Meeting of the Institute in 1935 (1). To avoid duplication, the present paper is confined to a discussion of the existing industrial mineral industry of the Province and of the factors governing its present and future development. British Columbia's mineral production in 1936 had a value approximately 15 per cent of that for the whole of Canada. Preliminary estimates for 1937 indicate that this proportion has been maintained, although the totals have increased about 25 per cent. The following table presents comparative figures, for the year 1936, illustrating the relative importance of the major divisions of the mineral industry in British Columbia and in Canada as a whole.

Jan 1, 1938

By J. R. Thoenen

In June 1929 the Bureau of Mines issued a 13-page Information Circular entitled "Mineral wool." This was one of the first publications to present to the public some technical aspects of the mineral-wool industry. Since that time several articles have appeared on the subject in the technical press as well as publications by State organizations. Inquiries for information on mineral wool have continued to be received by the Bureau of Mines in large numbers, and in 1935 it was decided, with the cooperation of the is industry, to make a field survey of the plants then producing and to collect therefrom technical data to be compiled in a paper for public distribution. As a first step, a brief questionnaire was mailed to the known producers asking if they would cooperate for publication. Favorable replies were received from of percent of the manufacturers, and the field work was started. As the study progressed and tie number of plants visited grew, it became more and more apparent that the industry had made rapid strides in technical operation and control of their product, as well as in increasing production during the mast decade.

Jan 1, 1938