Search Documents

This paper describes a proposal to reopen the Sylvia gold mine for underground exploration and development for an initial production of 10 000 tpa. A combination of trackless mining equipment and railtrack would be utilised for development with ore extraction being carried out by undercut and fill methods. The use of the smallest LHD units for mucking, and rail track for the main haulage together with airleg drilling will form the basis for development and stoping. The proposal has been subjected to an environmental impact assessment report to evaluate the impacts of the proposal on the natural and social environment in the area.

Jan 1, 1987

By Reda M. Bakeer

"Measurements obtained during load testing of two steel H-piles driven at a site in Northeastern Mississippi are discussed. The general site conditions, equipment used, testing procedures and results of the pile load tests are presented. Both piles were tested in compression and one of the piles was subsequently tested in tension. The piles were instrumented with strain gauges and extensometers to measure the mobilized soil resistance and pile movement. Three different “zero strain” conditions were used to determine the mobilized soil resistance and residual loads due to driving or a load cycle. It was concluded that the effect of residual loads on driven piles could be significant. Driving residual loads influenced the magnitude and distribution of the load transfer curves more than those due to a load cycle. Results of the tension test were impacted by the residual loads from the previous compression test performed on the same pile.INTRODUCTIONSeveral factors affect the performance of a deep foundation system including the subsoil conditions, loading settings, pile type and installation method. Residual stresses develop in piles particularly due to pile driving, but they are typically not accounted for in the analysis (Fellenius 2002). Siegel and McGillivray (2009) presented an assessment of residual loads measured during load testing of instrumented auger-cast-in-place (ACIP) piles. The magnitude and distribution of residual stresses along the pile shaft and toe depend on the pile installation method, previous load cycles and time effects. Poulos (1987) reported that residual load due to driving at the pile toe is independent of pile driving equipment and may significantly affect the results of a pile load test. Hunter and Davisson (1969) reported results of pile load tests performed in compression on fully instrumented piles driven in cohesionless soils along with a discussion of the effects of residual loads. Tension loads of about 445 kN (100 kips) were measured at the pile toe after driving. Unloading residual compression load at the toe was detected as “apparent” tension since the instrumentation was zeroed prior to the test. The researchers suggested a graphical approach to obtain the “corrected” load distribution curves considering that residual load will dissipate following the tension test. Holloway et al. (1975) conducted a study on the effect of residual stresses due to pile driving and developed a computer software that accounts for residual loads. Briaud and Tucker (1984) suggested a method to account for residual loads based on the results of 33 pile load tests performed in mostly cohesionless soils."

Jan 1, 2017

By O. Ogunsola, M. Downing

This paper gives a brief overview of impacts of coal blending on coal-fired power plants performance and discuses the preliminary results of an on-going study aimed at evaluating the effect of coal properties on the effectiveness, compatibility and thermal reactivity of coal blends. Plant survey studies reported no significant impacts on an existing plant designed for a high rank coal when switched to a blend of low- and high- rank coal. However, slight modification of some aspects (handling, fuel storage/stockpile, transportation, preparation, and general housekeeping) of plant design and operation may be necessary. The preliminary results of an on-going study at the Mineral Industry Research Laboratory shows that more compatible and better blends could be made from coals where ranks are closer than from those where ranks are far apart.

Feb 24, 1997

By Walter S. Bergholz, Michael L. Schreder

"Since Escondida began operations in fiscal 1991, a series of aggressive expansion projects have enabled market share to be increased and ever larger profits to be realized. This was possible due to the very large size of the ore body and its high grade - averaging 2.7% copper from startup through fiscal 1997. The situation has now changed: ore grade is falling rapidly and is projected to be only 1.55% by 2003. Since revenue is directly proportional to ore grade, while costs are proportional to quantity of ore processed, profits will begin to fall dramatically. The Phase IV Expansion Project is intended to forestall this drop in profits by increasing ore processing capacity by over 85%.The Phase IV concentrator is designed for a nominal capacity of 110,000 MTPD and the key to achieving this value is through the proper design of the grinding circuit. This paper presents the general design criteria for the grinding circuit, as well as a description of the facility.INTRODUCTIONThe Phase IV Expansion Project consists of a new copper concentrator located 8.5 km south of the existing operations, a new tailings disposal and water reclaim system, a new concentrate slurry pipeline to the coast, and added concentrate handling capacity at the port of Coloso. The new concentrator has a nominal capacity of 110,000 tonnes per day (MTPD), compared to the existing concentrator’s capacity of 127,500 MTPD. The Laguna Seca concentrator is based on using the largest and most efficient ore grinding mills now available.The concentrator has been designed for a 110,000 MTPD nominal capacity. The process design criteria for the Phase IV project were established from in-house operating information and from test work. Unlike a green field project, Escondida already had an operating plant and it processes ore from the same pit that feeds the Phase IV plant. It is expected that the current mineralization will be similar for the first 6 years of operation of the new project. Therefore, some of the current plant operating conditions were incorporated directly into the design criteria."

Jan 1, 2004

By Michel Doyon

Canadian Context: Exploration ??Space Exploration is within the unique mandate of the Canadian Space Agency ??Global partnerships ??Maintain close relationship with our partners ??New knowledge in S&T ??Retain and attract highly qualified personnel ??Participation in missions leads to design roles in industry and academia ??Collaboration between government laboratories, industry and academia

May 1, 2009

By Michel R. Julien, Michel Lemieux, Jean Cayouette, Daniel Talbot

"The Louvicourt Mine located near Val d’Or, Quebec has been in operation since 1994. It produces copper and zinc concentrates. The tailings generated from the ore processing operations have a strong net acid generating potential. Louvicourt Mine, a grass root project, was designed for closure with the best available technology at the time of design. In order to inhibit short and long time acid potential generation, sub-aqueous disposal was selected at the design stage. Given the fact that disposal in a natural lake was ruled out up front for obvious reasons related to loss of natural habitat and risks of permitting delays, a man made facility built with dams was planned. This mine includes therefore the first fully man-made sub-aqueous tailings disposal facility built in Canada. The requirement of using sub-aqueous disposal had serious implications on the placement of tailings. This tailings facility located about 9 km from the mine site has been selected based on the available natural confinement, the favorable foundation and hydrogeological conditions. This paper describes the site and the design criteria that were used. A presentation is also made on the placement technique to maximize storage and its impact on the operation of the basin. The performance of the basin, the dams and the decant structures is reviewed.Résumé : La mine Louvicourt, située près de Val d’Or, Québec est opérationnelle depuis 1994. Elle produit des concentrés de cuivre et de zinc. Les résidus générés par les opérations de traitement du minerai possèdent un fort potentiel net de génération d’acide. Le parc à résidus de la mine Louvicourt, implanté dans un milieu naturel intact, fut doté dès sa conception initiale de la meilleure technologie de fermeture disponible à l’époque, soit la déposition sous couverture aqueuse et ce, dans le but de bloquer le potentiel de génération d’acide à court et à long terme des résidus. Etant donné que la déposition dans un lac naturel fut mise de côté dès le départ pour des raisons évidentes reliées à la perte d’habitats naturels et au risque d’introduire des délais dans l’émission des permis, un étang artificiel délimité par des digues a été conçu. Cette mine fut donc la première au Canada à être dotée d’une installation anthropique de disposition des résidus sous une pleine couverture aqueuse. L’exigence d’une déposition sous couverture aqueuse a eu des implications sur le mode de mise en place des résidus. L’emplacement de l’installation de gestion des résidus a été choisi en un lieu situé à environ 9 km du concentrateur sur la base du confinement naturel disponible et des conditions hydrogéologiques et géotechniques favorables. Cet article décrit le site et les critères de conception utilisés. Une présentation est faite sur la technique de mise en place utilisée pour maximiser l’entreposage et son impact sur l’opération du bassin. La performance du bassin, des digues et des structures de décantation est également revue."

Jan 1, 2004

By R. G. Votteler, A. C. Brent

"The business performance of mining corporations in South Africa is adversely affected by the constantly increasing electricity costs. The most commonly used power sources are the national utility supplier via a grid connection, and on-site diesel generators. Previous research has identified the renewable sources of solar photovoltaic (PV), onshore wind, and geothermal energy in hybrid versions with current sources as possible opportunities to counteract rising electricity costs. To provide a clear understanding of the new, developing market of renewable energy sources, this research is divided into two papers. This first paper investigates the internal business structure of mining corporations in order to evaluate electricity generating sources. The multi-criteria decision analysis (MCDA) method is selected as the most suitable approach for this. The paper identifies the criteria used by mining corporations to evaluate possible electricity generation sources for self-generation by means of the corporations’ own investment. Four mining corporations with several mining locations were interviewed. The interviews revealed both new and identical evaluation criteria when the findings were compared to earlier MCDA adaptations analysed in the literature review. The second paper (Part 2) combines current knowledge about the external macroeconomic environment with the findings about the internal environment described here. MCDA is adapted in Part 2 and implemented to analyse and compare current to hybrid renewable sources from the perspective of mines. IntroductionMining corporations in South Africa are currently adversely affected by increasing electricity prices. Electricity is supplied mainly by Eskom1 and, especially in remote locations, by on-site diesel generators (Boyse et al., 2014). Electricity price increases, emanating from diesel price hikes and Eskom, have escalated the total operational expenditure on electricity by the largest mining corporations from 8% to 20% of total operating costs in the past seven years (EIUG, 2015). The reliability of electricity supplied by Eskom has decreased drastically (Govender, 2008), and the prices will increase annually by at least 13% until 2018 (Numbi et al., 2014; Eskom, 2015b). In addition, the South African government plans to introduce a carbon tax on greenhouse gas emissions (Alton et al., 2014)."

Jan 1, 2017

By L. J. Lorig

Much of the present knowledge about caving behavior of rock masses has been obtained from empirical observations. Additional notions about caving have been developed through inferences derived from two-dimensional finite element analyses. These analyses have indicated that a combination of one low-angle set of fractures and one nearly vertical set of fractures is the optimum fracturing configuration for ease of cavability of an orebody. This paper presents the results of two- and three-dimensional distinct element analyses which draw different conclusions than those reported from finite element studies. The distinct element method is selected far analysis of cavability because this method treats the rock mass as an assemblage of rock blocks which may interact individually, The results of the analyses are compared to a documented case history which involved a groundfall of 80,000 tons of ore in a 160-foot high pillar. The mechanics associated with these results are-explained in terms of simple static stability analysis of wedges. The propensity for orebody caving is primarily a function of the number of joint sets or potential "release" surfaces in the orebody. This mechanism is influenced by the bounding weak discontinuities, and intact strength of rock material.

Jan 1, 1989

At Waiuta near Reefton there is a remarkable vein of quartz <1 m thick which, apart from small offsets on late-stage faults, is a sheet like body essentially continuous down-dip and along-strike for> 1 km. The vein strikes NNE and dips steeply west (032/78¦W). From 1906-1951 the Blackwater mine produced 740,404 ounces of gold from the vein, called the æBirthday ReefÆ, which was one third of the total production from Reefton Goldfield and the fourth largest gold mine in New Zealand. Within the mine the vein is disrupted into a series of northeast-plunging shoots by late-stage faults. Similar faults, but with larger displacements, were thought in the past to truncate the vein at the northern and southern ends of the mine. The implication of this fault dissection model is that offset remnants of the vein await discovery. This study investigated the geometry of the vein and its relationship to host-rock structures and late-stage faults. A new model considers folding and lithological variation in the host-rocks to be fundamental in controlling the scale and geometry of veining, but does not rule out the possibility of some late-stage fault dissection. The Birthday Reef truncates 200-400 m wavelength folds in Greenland Group host-rocks at c.10¦ angle, that results in variation in the structural properties of host-rocks along strike every ~1350-2500 m. The spacing of fold hinges in the wall-rock veins is equivalent to the strike length of historic mining, implying that the Birthday Reef is probably hosted in a single limb of a fold. Similar relationships between mineralisation and host-rock folds appear to be present elsewhere in the Reefton Goldfield (e.g. Capleston and Murray Creek group of mines). Exploration targets are located one fold wavelength (c.1350-2500 m) further along strike from the Blackwater mine and relatively barren rock is expected in between the mine and target areas. Refining the location of folds and different host rock lithologies, using geophysical data and quality geological mapping, is the key to reducing exploration risks and discovering further resources.

Jan 1, 2000

By Mark A. Jirsa

The Biwabik Iron Formation is a ~1.9 billion year-old sequence of iron-rich sedimentary rocks that was metamorphosed at its eastern- most extent by ~1.1 billion year-old intrusions of the Duluth Complex. The metamorphic recrystallization of iron-formation locally produced iron-rich amphiboles and other fibrous iron-silicate minerals. The presence of these minerals in iron-formation along the eastern part of what is known as the Mesabi Iron Range, and their potential liberation by iron mining has raised environmental health concerns. We describe here the geologic setting and mineralogic composition of the Biwabik Iron Formation in and adjacent to the contact metamorphic aureole of the Duluth Complex. The effects of metamorphism are most pronounced within a few kilometers of the contact, and decrease progressively away from it. The contact aureole has been divided into four metamorphic zones?each characterized by the composition and crystal structure of the metamorphic minerals it contains. The recrystallization of iron-formation to iron-rich amphibole minerals (grunerite and cummingtonite) and iron-pyroxene minerals (hedenbergite and ferrohypersthene) is best developed in zones that are most proximal to the Duluth Complex contact. ©2007 Elsevier Inc. All rights reserved. Keywords: Iron-formation; Mining; Fibrous; Mineralogy; Metamorphism.

Jan 1, 2007

By Hamed Mirzadeh

The hot working behavior of 17-4 PH stainless steel was studied using the hot compression test at temperatures of 950-1150 °C with strain rates of 0.001-10 s-1. A step by step procedure for data analysis in hot compression test was given. The work hardening rate versus stress curves were used to reveal whether or not dynamic recrystallization (DRX) occurred. At low Zener- Hollomon (Z) parameter, this material showed a new DRX flow behavior, which was called Multiple Transient Steady State (MTSS). At high Z, as a result of adiabatic deformation heating, a drop in flow stress was observed. The general constitutive equations were used to determine the hot working constants of this material. Moreover, after a critical discussion, the deformation activation energy of 17-4 PH stainless steel was determined as 337 kJ/mol.

Jan 1, 2010

Gold recovered on the strikes at the Central Norseman mill, Norseman, Western Australia, has an approximate assay fineness of 850. Bullion recovered from the cyanide plant at the mine is of much lower value, and occasionally its assay fineness has been as low as 250. This indicates either that the fine gold particles in the ore consist of an alloy richer in silver than the coarse particles or else that a silver mineral, as well as the gold, is dissolved by the cyanide solutions.It had been observed at the mine that the amount of silver in the bullion appeared to increase when galena appeared to be more abundant in the stoped ore. Interest was, therefore, attached to the possible occurrence of a silver mineral associated with galena and, at the same time, soluble in cyanide.Four specimens of ore from different horizons in the mine were collected by the mine staff for examination as to whether any marked difference in the fineness of gold was apparent on a polished surface and for determination of the silver minerals. As the Norseman ore-body is a quartz reef containing a very small percentage of sulphide, the specimens were selected either because they cont;:lined free gold or because they were, relatively rich in sulphides. They were obtained from the following localities at the Phoenix shaft.1. Level 16, section 28.2. Level 16, section 31.3. Level 8, section 31.4. Level 14, section 38.Specimens Nos. 1 and 2 were thus obtained from different positions at the same mining horizon, while specimens Nos 2 and 3 were obtained from different levels in the same vertical section of the mine.All the specimens consist of quartz characterized by thin, discontinuous seams of sericite and the presence of a little ankerite. Gold and sulphides tend to be localized along these seams, but particles of gold and sulphides are also scattered throughout areas of white quartz. This scattered distribution of the sulphides in relatively wide areas of quartz has involved the preparation of two or more polished sections from each specimen.The outcome of the microscopical examination of these specimens has been to determine that there is no appreciable variation in the colour of the polished particles of gold and, therefore, no marked difference in the amount of silver alloyed with the coarse and fine particles. The presence of small quantities of the tellurides sylvanite, hessite and altaite has been revealed, and found to vary in abundance with the abundance of galena.

Jan 1, 1944

The paper outlines the development of a solvent extraction process for the recovery of scandium, yttrium, thorium, and heavy lanthanides from waste sulphate liquor at the Port Pirie uranium treatment plant. A summary is given of known solvents for these elements, including the recently developed alkyl-phosphoric acid esters which are applicable to sulphate solutions.A kerosene solution of di- (2'-ethylhexyl) phosphoric acid (EHPA) has been suggested by some workers as a suitable solvent for fractionation of the lanthanides. Experimental work with this solvent showed that it could be used for initial recovery of the above elements from low concentrations in the complex sulphate liquor. In particular, scandium could be recovered as a high grade product by extraction with 0·lM EHPA, followed by a purification strip with 9N sulphuric acid, and final stripping of scandium with sodium hydroxide solution.To enable alkaline stripping to be used successfully, the kerosene solution of the reagent was modified by the addition of a small proportion of nonanol. Experimental work included laboratory scale batch tests and small pilot scale continuous tests.A proposed extension of the process for the separate recovery of individual heavy lanthanides, yttrium, and thorium is described.INTRODUCTIONAt the Port Pirie uranium treatment plant of the South Australian Government, large volumes of "barren liquor", free from 'uranium, are at present run to waste. This "barren liquor" results from sulphuric acid leaching of Radium,Hill uranium concentrate, followed by separation of solid residues and removal of uranium from the clear solution by ion exchange. The mineral davidite, from which the uranium is derived, contains other potentially valuable components, notably vanadium, chromium, thorium, yttrium, scandium, and the lanthanides. These constituents are...

Jan 1, 1961

By M. Rahmanpour

"Mine planning is a multidisciplinary procedure that aims to guarantee the profitability of a mining operation in changing and uncertain conditions. Mine plans are normally classified as long-term, intermediate-term, and short-term plans, and many factors affect the preciseness of these plans and cause deviations in reaching the objectives. Commodity price is the heart of mine planning, but it has a changing and uncertain nature. Therefore, the determination of mine plans in the presence of uncertain mineral price is a challenge. A robust mine plan reduces the risk of early mine closure. A procedure is presented to determine the value at risk (VaR) in any possible mine planning alternative. VaR is considered together with downside risk and upside potential in order to select the most profitable and least risky plan. The model is tested on a small iron ore deposit. IntroductionMining projects are normally evaluated with the objective of maximizing economic value, as measured by the net present value (NPV). The aim of mine planning is to develop a yearly extraction plan that guides the mining operation to the highest NPV (Dagdelen, 2007; Yarmuch and Ortiz, 2011). This plan considers the technical constraints such as blending requirements, block sequencing, and pit slope (Caccetta and Hill 2003). Thus, the mine plan affects the economics and the payback period of mining operations.Mine planning is a procedure based on which the profitability of the mining operation is guaranteed in changing and uncertain conditions (McCarter, 1992). However, conventional mine planning ignores the volatility and uncertainty of future commodity prices and does not allow for managerial flexibility. It is common practice to assume a deterministic and constant commodity price through the mine life. The problem with this approach is that the commodity price is the heart of the mine planning procedure and governs the profitability and feasibility of the operation; thus ignoring price volatility will result in a sub-optimal mine plan."

Jan 1, 2016

By Peter J. Nicholson

Since the reintroduction of soil mixing to the United States over 10 years ago, the work installed by soil mixing technology has grown dramatically. From an annual turnover of less than ten million dollars per year the volume of soil mixing put in place has grown to an estimated $40 million per year in the year 2000. The majority of work done to date has involved walls, either for excavation support, permanent retaining structures or hydraulic cut-off walls. The other major use for soil mixing has been for mass stabilization of soils whether for isolation of contaminants or for retaining structures. This paper will discuss the uses of and costs of typical soil mix structures. BACKGROUND Soil mixing is defined as the in-situ combining of reagents, typically cement, with native soils, the purpose being to modify or improve the ground. This history of soil mixing covers only the use of cement slurry, aggregated with soil in-situ by mechanical mixing methods only. Soil mixing by use of high-pressure hydraulic means, also known as Jet Grouting, will not be discussed. In addition this will not cover ex-situ (above ground) mixing, or mixing dry reagents with soil. Only mixing applications for building, civil and heavy construction applications will be discussed, with only passing reference made to uses of soil mixing for environmental remediation work.

Jan 1, 2001

This paper reports on recent field observations on the performance of support systems under different corrosion environments in Canadian underground mines. Phenomenological data are used to gain a better understanding of the main causes of corrosion in underground metal mines. Preliminary field data collected from five metal mines have been complemented by atmospheric and water sample analysis as well as fractography and metallographic studies. This has identified dominant factors that control the corrosion of support systems. The data are analysed in order to develop a support strategy for mines operating in corrosion environments.

Jan 1, 2008

THE following really forms the second part of, or a sequel to, a paper, " Ventilating Metalliferous Mines: a Method of Attack," read before the Broken Hill Branch of the Australasian Institute of Mining and Metallurgy in May, 1920. In that paper the writer advocated a consideration of the question of ventilation in metal mines from a different aspect to that 'which had hitherto prevailed locally. Various factors regarded as having an important bearing on the subject were set forth, together with the results of observations made during ventilation tests carried out at the mining department of the Zinc Corporation.During the subsequent discussion the question was raised of the possibility of any practical application of the method of attack described, and also whether the theoretical considerations mentioned were likely to be of any real utility to the mining engineer engaged in ventilation work in a metalliferous mine.

Jan 1, 1923

By G. St. J. Perrott, G. W. Jones

"In the course of its investigations pertaining to the promotion of safety the Bureau of Mines is actively engaged in investigating all promising materials that may be of value in rendering methane or other combustible gases, vapors, or solids less inflammable.Added substances are of value if such additions narrow the limits of inflammability, raise the ignition temperature, lower the speed of propagation of flame, or reduce the maximum pressure developed. Of major importance is the effect of added materials on the limits of inflammability, because methane is the chief combustible s liberated in mines, considerable work has been done with extinguishing agents on methane flames. For obvious reasons, a substance to be of value for the extinction flames should be a gas, or a liquid having a sufficient vapor pressure to give concentrations of the vapor in sufficient amounts to extinguish the flames or markedly narrow the limits of inflammability. The substance should be nontoxic, cheap, and noncorrosive and must be incombustible. Solids, such as rock dust, are undesirable and of little value for combustible gases because they soon settle out of the atmosphere, and their flame- extinguishing value is thereby lost. There are at present only a few gases and vapors-for example, nitrogen, carbon dioxide, and carbon tetrachloride-which meet these requirements.The extinction of methane flames by nitrogen, carbon dioxide, and argon has been reported by Coward and Hartwell 4; the extinction by water vapor by Coward and Gleadell 5, and the extinction by helium and carbon tetrachloride by Coward and Jones 6."

Oct 1, 1930

Mining is taking place at increasing depths of cover on the Southern Coalfield beneath predominantly massive sandstone strata. Within the next twenty years, there will be longwall mining at depths greater than 600 m. As the Sydney Metropolitan area continues to expand and as coal mining approaches these urban areas subsidence will continue to become an increasinglY important aspect of coal mining research. Investigations, commenced in the mid 1960's, allow prediction of subsidence in the Southern Coalheld with reasonable confidence. The work is showing that the characteristics of thc subsidence troughs over the deeper mining at Appin differ from the characteristics of mine subsidence at less cover.The longwall mining at Appin Colliery has resulted in a maximum measured subsidenee of 730 mm. The maximum strains were small because of the large radii of curvature of the subsidence profiles. There was no damage to any of the buildings in the township of Appin.

Jan 1, 1982

By Slechta J. J

An evaluation of a pilot scale Delkor horizontal belt filter at Bellambi's South Bulli Colliery showed high productivities and low moisture contents for a range of feed slurries. When treating flotation concentrate, a productivity in excess of 1000 kg/m2/hr (dry) at a moisture content of less than 22 per cent was obtained. The results indicated the belt filter had a capacity twice that of conventional drum or disc filters, and was capable of dewatering a very fine, thickened, classifying cyclone overflow slurry to an acceptable moisture content. The superior performance of this filter is discussed in terms of the factors influencing cake formation and the stratification of solids in the filter bowl of a conventional rotary vacuum drum filter.

Jan 1, 1986