Search Documents

By Delahant A. B, Dworski M

From the Saranac Laboratory for the Study of Tuberculosis of the Edward L., Trudeau Foundation, Saranac Lake, New York:We are assembled to honor the memory of our friend and colleague, Donald Cummings, one of the founders and a past president of the American Industrial Hygiene Association. I deem it an Unusual privilege to have been asked to give this first memorial lecture and hope that what shall have to say may be worthy of the occasion. It is fitting that we should discuss here the subject of Silicosis to which he devoted such a large part of his life and it is doubly fitting, I think, that I should report to you an extended series of investigations carried on by his associates at the Saranac Laboratory.The subject of silicosis may seem hackneyed to this audience which is so familiar with the tried and accepted methods of prevention and control.But in spite of our efforts, the condition is still with us and unfortunately is still being produced in many places. In industries that now maintain good control of dust, fresh cases are appearing on annual re-examination, whose major exposure date back to the days before the hazard was recognized.A few new employees, with apparently ineffective upper respiratory protection against inhaled dust, develop silicosis precociously in environments that are comparatively harmless to their fellows. In plants that have relaxed their vigilance under the urgency of war production schedules, conditions again prevail that will produce, disease in the future.Silicosis acquired new interest with the announcement by Denny, Robson and Irwin(1) in 1937 that it could be prevented by the inhalation of powdered metallic aluminium. It so happened that without knowledge of their work, we at the Saranac Laboratory had for some months been conducting similar experiments with one of the hydroxides of aluminium.Quite independently we discovered that hydrated alumina would also protect animals against quartz. Our approach to the problem had been empirical; we were trying to neutralize quartz particles by coating their surfaces with an insoluble material following the lead of Kettle who in 1932 had shown that this could be accomplished with iron. He neglected to describe his method and the chemist who prepared his coated...

Jan 1, 1945

By S. Roy

Soft laminated iron ore (SLO) having a higher hematite content and Martite goethite iron ore (MGO) having a higher goethite content were subjected to detailed characterization and beneficiation. The present research was designed to investigate if these abundant, low-grade ores can be enriched adequately using standard industry techniques. No significant enrichment of the ores using jigging operation on the coarse (-3,200 +595 mm) size fraction could be achieved. Good liberation was only attained in the 150 to 300 mm particle size range in both cases. Desliming enriches the ground ores significantly. The effect of the feed size on the separation efficiencies of the ground ores were studied using flowing-film concentration on a Wilfley table. Better enrichment is obtained in the case of 150-mm sized feed by tabling. The grade of SLO is improved from 56.14% to 66.51% Fe, while the Fe content of MGO is enriched from 55.16% to 65.83%. Substantial rejection of alumina and silica is also achieved. Due to the friable nature of MGO and the higher goethite content in it, the loss of Fe in the form of ultrafines is greater in this case compared to that of SLO.

Jan 1, 2009

By N. Krauland, A. Nystrom, M. Board, S. Sandstrom

Several deep Swedish cut-and-fill mines experience severe ground control problems, including roof collapse and wall sloughing, as a result of variable rock quality and high in situ stresses. A project to examine the problem included two main areas. The first was prediction of mining conditions at depth and the adaptation of cut-and-fill mining to such conditions; the second was the assessment and improvement of support methods at present and future depths. Simple, elastic, mine-scale numerical models were used to optimise stope sequencing and more detailed, stope-scale models to simulate the failure processes around a stope and the interaction of rock mass and support. Kristineberg was chosen for testing and calibration of the predictive methods because of its long history of severe ground conditions and the large base of observational and monitoring data available for comparison. Horizontal cut and fill was found technically suitable to depths beyond 1 000 m and economically viable if ore value covers support costs. Stability can be achieved with the present support technology down to 1 000 m but the 7-strand 15.2 mm cables have poor deformation properties (5% failure strain) compared with rebar rock bolts (17%). Reducing the intervals between levels from 100 m to 50 m will cut support costs and improve production reliability and capacity. Simulation of sill-pillar mining indicated that conditions would be most severe when pillar height was reduced to 15-20 m; mining of a sill pillar has been carried out successfully to the last 3 m, whose extraction is planned for the near future

Dec 1, 1995

By Robert Jakiel

The following paper is being presented to provide an understanding of the Deep Soil-Cement Mixing (DMM) performed at Contract C09A7 at the Fort Point Channel Site (FPC), for the I-90/I-93 Interchange of the Central Artery/Tunnel Project (CA/T), Boston, MA. The paper is written as a summary of the DMM from the DMM Contractor's perspective. The summary provides technical information and practical observations that are currently considered to be state-of-the art knowledge within the soil mixing industry. The observations and information are being provided by Robert L. Jakiel, Chief Engineer of SMW Seiko, Inc., who was the DMM Project Manager and Project Engineer for the A7 Joint Venture at FPC. The DMM was started in April of 1996 and completed in December 1999. The various acronyms and terminology used to describe the soil mixing are found in a section at the end of the paper.

Jan 1, 2000

By Nathaniel Arbiter

Flotation’s earliest patent was issued in 1860. However, the process was first applied commercially in Australia until 1904, and in Montana in 1911. Major advances followed both in reagent treatment and in cell design, with resulting process improvements. Mechanical cells have seen the widest use and with the major increases in plant capacities (Fig. 1) their volumes have also increased (Fig. 2). In 1991, the principal use for the process was to produce copper concentrates for smelting. It was applied to 243 Mt (268 million st) of copper ore. The total of all ores floated that year was 426 Mt (470million st). In 1997, US mines produced 257 Mt (284 million st) of copper ores for flotation, yielding1.75 Mt (1.94 million st) of copper.

Jan 1, 2000

By R. D. Stewart

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 18pp., 5 refs. A seismic risk assessment method has been developed for application to rockburst prone deep-level mining sites which have sufficient seismic coverage. The technique utilises several seismic hazard parameters simultaneously and assesses the seismic risk on a daily basis according to the individual levels of these parameters. Critical levels are determined from investigation of the long-term behaviour of the parameters in relation to recorded potentially damaging seismic events. The method has been applied to a data set comprising 15 months' worth of seismic data, with encouraging results

Aug 1, 1995

By J. D. Lowell, L. Quevedo

I will talk today about a porphyry copper exploration program now underway in the Amazon jungle in the southeastern part of Ecuador near the border with Peru. The project is unusual for two reasons: first the deposits are of Jurassic age, 153 m.y.o., which is unusually old for porphyry copper deposits and they may be the most significant pre-Tertiary age porphyry deposits known. Second, the district was found only six years ago which makes this the most recent discovery of a totally new porphyry copper district. The new porphyry district, known as the Zamora River Copper Belt, or the Corriente Copper Belt, is a north trending area 50 km long by 10-15 km wide, which is nearly aligned with the axis of the Jurassic age Zamora batholith and with the course of the Zamora river. Gencor in 1994 initiated a regional grassroots gold exploration program based on reconnaissance geologic mapping and geochem sampling which did not find a gold mine, but which identified the San Carlos porphyry copper system in April, 1995. In a later reorganization between Gencore and Billiton the Ecuador project was transferred to Billiton and between the Gencore work and Billiton’s a total of 10 porphyry copper systems were found over the next four years. In the period of 1997 - 1999 Billiton drilled a total of 11,000 meters of wide spaced core holes in the San Carlos, Panantza and Kutukus prospects. In October 1999 Billiton concluded a farm-out, joint venture agreement with Corriente Resources and Lowell Mineral Exploration for additional exploration of the Zamora property. This is funded by Corriente and managed by Lowell Mineral Exploration and a total of 28,000 m of core drilling was completed through August 2001. An immediate result of the Corriente Lowell project was the discovery of potentially commercial ore reserves in two new deposits at Mirador and Warintza. Additional closer spaced drilling was done in the Panantza deposit and additional drilling is planned at San Carlos, in targets related to Warintza, and elsewhere.

Jan 1, 2002

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4-km- (6.5- mile-) long, 14.4-m (47.5-ft) bored tunnel that will run under the city of Niagara Falls from the Upper Niagara River to the Sir Adam Beck power station. The completed project will enhance the capacity of the Sir Adam Beck power station by adding 500 m3 /sec (17,657 cu ft/sec) of water through the tunnel. The project uses the world?s largest hard-rock tunnel boring machine (TBM) at 14.4 m (47.5 ft) in diameter to excavate the tunnel. Features of the project include the use of a high performance (HP) main beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area In June 2004, the Ontario government announced that Ontario Power Generation (OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls ? the first two tunnels were constructed in the 1950s using drill-and-blast techniques. The third tunnel, appropriately named the Niagara Tunnel Project (NTP), consists of a 10.4-km- (6.5-mile-) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG the selected of Strabag of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP at a price of C$600 million. In September 2005, Strabag selected The Robbins Co. of Solon, OH to design, manufacture and deliver a new 14.4- m- (47.5-ft-) diameter high performance, state-of-the-art main beam hard rock TBM to be used in the excavation of the tunnel. To meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be sup-plied as ready-to-bore within a 12-month period after the contract was awarded to Robbins.

Jan 1, 2008

By M. Pineda

Sublevel stoping (SLS) is one of the oldest and most used methods for underground mining. It relies heavily on the use of drilling and blasting techniques to remove the rock, and gravity to transport the broken rock to drawpoints located at the base of the stope, with LHDs to transport material from the drawpoints. Current SLS operations are based on the assumption of stable geometry of the stope. Thus, the stope design includes the definition of the geometry according to the orebody shape and geomechanical constraints to avoid instability, which may cause excessive dilution. Under some circumstances, dilution could enter the stope due to geotechnical instability, especially when large stope geometries are used. A review of current design and planning practices for large SLS operations indicates that no consideration is given to the material flow and the mixing that occurs after blasting. Material flow could have a large impacton the mixing of ore when grades are heterogeneous in the stope. In this paper, we discuss the influence of gravity flow on the design and planning of large sublevel stopes with and without vertical dilution, based on laboratory experiments. The outcomes of this investigation are used todevelop guidelines towards the design and planning of large SLS mines, which would complement the currently used geotechnical considerations.

Jan 1, 2015

From a vast army of workers to gargantuan machines to immense volumes of material being moved, almost everything about the Port of Miami Tunnel (POMT) project points to tunneling on a massive scale. Almost.The star of this underground and underwater show is a Herrenknecht tunnel boring machine (TBM,) nicknamed ?Harriet? by a local Girl Scout troop. With her 12.9-m- (42.3-ft-) diameter cutting head and a total length of 139 m (457 ft), Harriet is boring through thousands of cubic meters of clay, dirt and sand, which is often mixed with coral and other materials, to create two 1,280-m (4,200-ft) traf?c tunnels connecting Watson Island and the Port of Miami (Dodge Island) beneath Biscayne Bay, FL. But in the midst of all of the oversized equipment and machines, a strong contender for the best supporting nod goes to a relatively tiny machine: the Brokk 400. Bouygues Civil Works Florida crews are using the compact, remote-controlled and electric-powered machine to excavate five cross passages between the twin traffic tunnels. The pas-sages will be essential to the safety of people who drive their vehicles under the bay every day.

Sep 1, 2013

By R. L. Virta

Four companies mined ball call in four states in 2009, H.C. Spinks Clay Co. Inc. (owned by Lhoist Group), Kentucky-Tennessee Clay Co. (owned by Imerys Group), Old Hickory Clay Co. and Unimin Corp. Production, on the basis of preliminary data, was 820 kt (904,000 st) with an estimated value of $39.4 million. That was a 15-percent decrease in tonnage from 967 Mt (1.1 mil-lion st) with a value of $44.3 million that was produced in 2008. Tennessee was the top producing state with 59 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 71 percent of production was airfloat, 18 perc

Jun 1, 2010

By Desiree Willis

Disc cutters have determined excavation rates of rock tunneling projects for more than 50 years. First developed in 1956 by James S. Robbins, disc cutters (then 279 mm or 11 in. in diameter) were used to bore limestone of 190 MPa (27,500 psi) unconfined compressive strength (UCS) and were loaded with 7.12 t (15,700 lbs) each. Modern cutters have reached up to 508 mm (20 in.) in diameter and are typically loaded with up to 31.7 t (70,000 lb) to economically bore through the hardest of rock up to plus 400 MPa (60,000 psi) UCS. New developments, such as larger cutter diameters, are geared to increasing the bearing capacity and wear life of the cutting structure. This, in turn, increases cutter life, cutter load and cutter penetration. Disc cutters have also been re-designed on a small scale for use in hard-rock utility installations. Additional variables also affect the three factors, including cutter spacing on the cutterhead, cutterhead diameter and cutter materials.

Jan 1, 2007

By S. H. Ash, E. M. Brooks

"Many of the hoisting slopes at the mines in the State of Washington are driven on extra steep dips. To facilitate hoisting they are driven wide enough to provide two tracks. The cars are handled by high-speed, first-motion electric hoists and the trips run in balance.The State mining laws a provide that special man-cars be provided on slopes of 20° or more and that no one be allowed to ride while any loaded car is being hoisted in any slope in a mine. Obviously, in addition to the fact that it is more or less hazardous to ride while an empty trip is being hoisted, considerable hoisting time is lost during the day if some one has to ride the trips in the slope.Owing to the locations of pumps and various types of equipment, more or less travel is required up and down the slope. Not only to provide a proper safety factor but also to comply with the law, some other means of transportation in an¬other passageway is desirable. This is sometimes recognized in large mines by pro viding separate hoisting shafts, or slopes, and necessary equipment, which are use for transporting men and material. The handling of material in itself would justify the system in most large mines.The following description of an automatic electric man-hoist was prepared from data furnished through the courtesy of Mr. Thomas Murphy, superintendent of the Northwestern Improvement Company's mines in the Roslyn-Cle Elum coal field.The special features of this hoist are that no hoistman is required and its operation is always under the control of the person or persons riding the trip.The hoist was installed at mine No. 5, Roslyn, Washington, to provide a means of entering and leaving the mine on idle days or at night when no hoistman was on duty and to make it unnecessary to use the main hoist for a man trip during working hours. It has been in operation for about two years and has given very satisfactory service.The hoist, with all accessories, is housed in a concrete building 200 feet back from and in direct line with one of the main airways. One car with a capacity of six men operates over a distance of 1,200 feet on a 38° pitch.The wiring details of the electric circuits which control the operation of the hoist are shown in Figure 1-a.The hoist is driven through a worm gear by a 500-volt shunt-wound direct-current motor at a car speed of 120 feet per' minute. A gravity friction brake with magnetic release is mounted on the- motor shaft and is wired in multiple with the motor field coils. The hoist drum is also equipped with emergency friction brakes, which operate by gravity and are released, in case of overspeed, by the governor geared direct to the drum shaft. When these brakes set the control circuit is opened at contact 2E-2C and the motor stops.If the descending car meets some obstruction and is stopped, the hoist continues to run and unwind the rope. To guard against this occurrence, a weighted sheave wheel rides the rope 4 feet from the drum, and if the rope becomes slack the rider drops downward and opens the contact 2C-2E which stops the hoist.Limit switches, S1 and S2, are located on the hoist indicator, which is connected to the drum shaft through sprockets and chain. The pointer P indicates the position of the hoist at all times."

Jul 1, 1930

Fine Gravity Separation in the Reflux Classifier, Exploiting a High Shear Rate, Laminar Flow Mechanism The Reflux Classifier is used in the gravity separation of particles over a broad range of particle sizes. The device consists of a fluidised bed zone, with a system of parallel inclined channels above. The inclined channels provide a significant hydraulic advantage over conventional fluidised beds via the so-called Boycott Effect (Boycott, 1920). This paper describes a new advance in fine gravity separation based on the high shear rate and laminar flow profile that arises when closely spaced inclined channels are deployed. As reported recently (Galvin et al, 2009a), a powerful density based separation mechanism develops from this arrangement, suppressing the effects of particle size. In this paper we focus on two areas, firstly the application of the separator in the laboratory for batch fractionation of particles of varying size and density to determine the grade recovery curve and hence the liberation, and secondly the step change in separation performance achieved on a continuous steady state basis when closely spaced inclined channels are used. The variation in the separation density with particle size decreases significantly, and the Ecarte Probable Error (Ep) remains at low levels over a broad size range.

Sep 13, 2010

By Osvaldo A. Bascur

Connectivity between mining and metallurgical process operations and their business systems has become a reality. Expanded use of plant information on the desktop is a standard tool for revenue improvement, cost reduction, and adherence to production constraints. The industrial component desktop support access to information for continuous improvement and innovation by staff personnel and engineers. Collaboration between groups enables the implementation of an overall process effectiveness index based on losses due to equipment availability, production recovery and quality rate. In this sense, the paper point out three cases studies of large integrated power stations.

May 25, 1998

By J. Kerr

The first stage of the development of a new modified 201-type low nickel austenitic stainless steel is described in this paper. The alloy is intended for use as a structural alloy, and so requires a yield strength >400MPa as well as acceptable weldability and toughness. The low nickel content will give a lower material cost in comparison to more conventional austenitic grades, and the processing route is required to be similar to that of Type 304 to keep the processing cost low. The base alloy was designed using empirical methods developed for stainless steel, and the properties of the base alloy were verified using a range of small-scale melts. The base alloy had a 0.2% proof strength of ~320-400MPa, and so it is planned to use V additions of ~0.15% to bring about precipitation strengthening in the hot rolled condition, so raising the alloy?s proof strength above the 400MPa minimum.

Jan 1, 2004

By Camilo I. Morales

At present, many open pit mines are designed to operate and feed a processing plant with ore characteristics that were defined in the design of the mining business, which are not necessarily the same as those found during the operation. This is the case of Spence Mine, whose design was conceived considering the extraction of primary iron sulphides, however, with the extraction of such minerals, it was necessary to mine and process minerals with secondary enrichment. Then it is necessary to work with a greater selectivity degree in the operation, however the capacities of the mine and operational resources were not designed for this. Thus, the changes in the general conditions of the operation should be considered as a series of geometallurgical restrictions to achieve production schedules. The above facts impacts directly in the short-term planning, whose task is to achieve the goals proposed in productive long-term planning because the company does not have the tools necessary to plan with the degree of selectivity required, so it should be done by hand, discretizating and scheduling the production polygons. Naturally, this manual process in the short term planning deviate sharply from the areas in operation, opening new fronts and benches that result in a significant increase in costs and a loss of the value of the mineral resource to miss the exploitation sequence. The research presented in this paper is related to the development of a mathematical programming model to support the short-term planning, so as to integrate the challenge of selective mining with geometallurgy restrictions, to provide the planner a guide to construction of the polygon of exploitation, guiding the fines production to achieve the goals of the proposed production plan.

Oct 1, 2009

Any hypothesis for the origin of the Otago gold-quartz lodes must account for the following observations. 1. Southeast of Glenorchy, where the schists hosting the lodes are comparatively unaffected by Neogene Alpine Fault deformation, the dominant strike of the vein systems is NW-SE, parallel to the axis of greatest post-metamorphic uplift in the Otago Schist belt (Paterson, 1986). 2. The lodes are fault-hosted, with some developed along steep, low-displacement normal faults (eg Barewood, Bendigo, Nenthorn), implying NE-SW extension, and some developed along low-angle thrusts (eg Macraes) implying, in apparent contradiction, NE-SW contraction (Teagle et al, 1990). 3. The mineralising fluid was of metamorphic origin (McKeag and Craw, 1989), but while some of the lodes developed in a mesothermal environment at considerable depth (eg ~10 km for Macraes), others appear to have formed at very shallow depth (eg <1 km for Nenthorn) (Craw and Norris, 1988). 4. The timing of the mineralisation is generally poorly constrained but postdates the main Rangitata schist metamorphism. It probably initiated during early Cretaceous exhumation and unroofing of the schist belt (140 - 120 Ma?) and may have continued well into the Tertiary (Craw, 1989). Estimates for the relative ages of the different lodes are largely speculative but, based on pressure estimates from fluid inclusion studies, Macraes likely represents the deepest and oldest lode system while Nenthorn (just 12 km to the southwest) is perhaps the shallowest and youngest (Craw and Norris, 1988).

Jan 1, 1992

By M. Cai

A practical simple method is proposed to estimate the tensile strength (st) of strong brittle rocks from the strength ratio of R= sc/st = 8 sc/sci, where sc is the uniaxial compressive strength and sci is the crack initiation stress in an uniaxial compression test. 8 is the Griffith strength ratio and the term sc/sci accounts for the difference of crack growth or propagation in tension and compression in uniaxial compression tests. sci can be reliably obtained from volumetric strain measurement or acoustic emission (AE) monitoring. With the strength ratio R determined, the tensile strength can be indirectly obtained from the result of uniaxial compression tests. In addition, a practical estimate of the Hoek-Brown strength parameter mi is presented and it is suggested that mi = 12 sc/sci can be applied to strong, brittle rocks in high confinement zone and mi = 8 sc/sci can be applied to low confinement to tension zones. It is found that the predicted tensile strengths and Hoek-Brown strength parameter mi using this method are in good agreement with test data. The rock strength parameters like st and mi, which require specialty tests such as direct tensile (or Brazilian) and triaxial compression tests for their determination, can be reasonably estimated from uniaxial compression tests.

May 1, 2009

By Anand Raman, Steve Dixon

"Industry practice for defining acid consumption is based on column tests. Freeport-McMoRan (FCX) has adopted a practice of leach operation using a defined pH or gpl acid in the raffinate based on the column test program. The acid consumption can be easily calculated using the leach operating parameters of SX-EW efficiency, lift height, bulk density, irrigation rate, primary leach cycle time, acid cure dose and acid concentration in the raffinate. The column leach test results and a column to heap efficiency factor are used to define the copper extraction. The maximum acid consumption will occur when zero acid is contained in the raffinate. The term Net Extracted Value (NEV) is to define the maximum extracted value relative to acid consumed.This paper presents the operating logic and method used to calculate acid consumption based on column tests and operating parameters.INTRODUCTIONIndustry practice for defining acid consumption is based on column tests. This may result in lower economic value if the tests are not designed to account for operating variables. A test program is described to assist in defining lift height and the influence of gangue on solution chemistry. A simple spreadsheet is presented that will use the leach operating parameters of SXEW efficiency, lift height, bulk density, irrigation rate, primary leach cycle time, acid cure dose and acid concentration in the raffinate to calculate the acid consumption for a proposed operation.A review of current leach operations solution chemistry will help to define acid consumption. This is recommended for all current leach operations.DISCUSSIONThe current practice at Freeport-McMoRan (FCX) is the use of column test results to define operating parameters. The monitoring of operational solution chemistry and copper production addresses any changes needed in operational parameters. This practice maximizes the value extracted from each tonne of ore leached."

Jan 1, 2008