Search Documents

By M. A. W. Bryson

It is well documented that a significant amount of the new PGM (Platinum Group Minerals) production that is coming on stream now, and over the next few years, is to come from the UG-2 reef. Clearly the reservations, or perhaps the perceived reservations, attached to the processing of this ore are no longer there. What were the metallurgical issues that delayed the exploitation of the PGM values from this reef? Traditional furnaces treating Merensky concentrates were not able to accept the concentrate produced from a UG-2 plant due to the relatively high chromite content of this product. The chromite reports to an insoluble spinel phase that accretes in the furnace, resulting in the necessity to shutdown and dig the furnace out periodically. This was clearly not an attractive economic option, so producers stayed away from it in the early days. The Merensky ore had all higher base metal credits anyway, and you needed them to get a matte fall, so there was no driving force to look seriously at the UG-2 reef. Platinum demand at this time could be easily met from the Merensky ore, so the motivation to tackle more complex ores was not there. The low price of PGMs meant that these operations were not particularly profitable and there was little effort directed at improving the operations. Concentrators were generally not run very efficiently and the emphasis was on cost reduction through increasing milling rates.

Jan 1, 2004

By B. A. Wilcox

ThERE are several reports in the literature which indicate that both solid-solution hydrogen and hydride precipitates can promote low-temperature em-brittlement of tantalum.1-3 For example, Imgram et al.2 showed that hydrogen additions in the range of 140 to 580 ppm promoted a ductile-to-brittle transition at slightly above room temperature in both wrought and recrystallized tantalum. This contrasts with the observation that tantalum of norma1 purity is very ductile, even at liquid-nitrogen temperature. Imgram et al. also found that hydrogen additions caused a deterioration of notch tensile properties of tantalum. The purpose of this communication is to present some limited evidence that hydrogen can also cause fatigue embrittlement of tantalum. The material used in this investigation was wrought, stress-relieved (1000°C, 1 hr), are-melted tantalum rod (5/8-in. diameter) containing the following impurities in weight percent: 0.005 C, 0.007 02, 0.0005 H2, 0.003 N2, 0.08 Cb, 0.01 W, and 0.01 Fe. Hydrogen charging was done in an atmosphere of flowing dry hydrogen for 3 hr at 600°C, followed by an homogenizing anneal in purified argon for 15 min at 600°C, and cooling in an argon atmosphere. Typical micro-structures of the hydrogen-free and the hydrogen-charged materials are shown in Fig. 1(a) and Fig. 1(b), respectively. Fig. 1(b) shows the appearance of hydride precipitates which, in many cases, formed preferentially parallel to the rod axis. The hydride dispersion was uniform across the diameter of the specimen. The fact that the precipitate was a tantalum hydride was tentatively confirmed by X-ray diffraction on a metallographically prepared surface. After hydrogen charging, chemical analyses by vacuum fusion revealed the hydrogen content to be 0.0295 wt pct. In addition, the oxygen and nitrogen contents were slightly raised to 0.0095 O2 and 0.005 N2.

Jan 1, 1964

By J. Werfling, J. R. Kiehl

SUMMARY: The effects of blasting on structures are assessed on the basis of the maximum amplitudes of the occuring vibration velocities. If the standard values in the German Standard DIN 4150 are not exceeded, damages to structures are not to be expected. The estimation of the maximum vibration amplitudes is usually based on experience or on emperical formulae. However, a comparison of expected with measured values shows that these estimations are not conservative, particulary in case of small distances between blasting locations and structures. More reliable predictions are possible on the basis of numerical analyses, which simulate the three-dimensional propagation of waves with consideration of the geomechanical and geometrical conditions. In addition to the expected velocities, these analyses also allow the determination of stresses resulting from dynamic loading. If the dynamic stresses are known, the effects of blasting on structures can be predicted. ZUSAMMENFASSUNG: Die Auswirkungen sprengbedingter Erschütterungen auf bauliche Anlagen werden in der Praxis auf der Grundlage der Maximalamplituden der auftretenden Schwinggeschwindigkeiten beurteilt. In der DIN 4150 werden Anhaltswerte angegeben, bei deren Einhaltung Schäden von Gebäuden nicht zu erwarten sind. Die Abschätzung dieser Schwing-geschwindigkeiten erfolgt meist auf der Grundlage von Erfahrungswerten oder empirischer Formeln. Der Vergleich der prognostizierten Werte mit Meßergebnissen zeigt jedoch, daß diese Ansätze insbesondere dann, wenn die Abstände zwischen den Sprengorten und den Gebäuden gering sind, nicht konservativ sind. Zuverlässigere Prognosen sind auf der Grundlage von numerischen Berechnungen möglich, in denen die räumliche Ausbreitung von Erschütterungen unter Berücksichtigung der geomechanischen und geometrischen Verhältnisse simuliert wird. Mit derartigen Berechnungen können die zu erwartenden Schwinggeschwindigkeiten und die aus der dynamischen Beanspruchung resultierenden Spannungen ermittelt werden. Dies ermöglicht Aussagen über die Auswirkungen sprengbedingter Erschütterungen auf Bauwerke. RÉSUMÉ: Les conséquences de vibrations résultantes d'explosions pour des bâtiments sont estimés dans la pratique à partir des amplitudes maximales des vitesses d'oscillation. Dans la norme allemande DIN 4150 des valeurs d'orientation sont données, avec l'observation desquelles de dommage à des bâtiments n'est pas à présumer. Ces vitesses d'oscillation sont estimés généralement à partir de valeurs d'expérience ou de formules empiriques. La comparaison des valeurs prédits avec des résultats de mesures montre cependant que ces hypothèses ne sont pas conservateurs, en particulier si les distances entre les lieux de sautage et les bâtiments sont petites. Des prédictions plus fiables sont possibles à partir de calculs numériques, dans lesquelles la dissipation spatiale de vibrations est simulée en considération de la situation géoméchanique et géométrique. Avec tels calculs les vitesses de vibration à présumer et les contraintes résultantes de l'effort dynamique peuvent être établies. Cela permet de constater sur les conséquences de vibrations résultantes d'explosions pour des bâtiments.

Jan 1, 2003

By F. Bonnet, J. Lehmann, H. Gaye

A review of thermodynamic information and models of slags, including associated software when available, is presented. The pertinence and accuracy of these models is discussed by comparison of their predictions for various slag thermodynamic properties with the available experimental data. Practical industrial applications will be illustrated by a literature review of the dephosphorization process of ferromanganese alloys and by the description of Ti behavior during silico-manganese alloys production. This latter example will show how the thermodynamic models have been used to propose a flotation treatment at low temperature to enhance TiC removal.

Jan 1, 2004

By A. T. Yu

On March 18, 1964, the 52,000 dwt ore carrier M/S Houn Maru called at the port of Coquimbo, Chile, on its maiden voyage to take iron ore to Japan. This marked the first time a vessel of this size ever arrived at Coquimbo, and the event promises to drastically accelerate henceforth iron ore exports from Coquimbo province. This was made possible by the use of a versatile shiploading system recently installed by Cia. Minera Santa Fe. Coquimbo has no mechanized loading facilities other than six conventional 5-ton cargo cranes. Limited space on shore further complicates the stocking problems. To make the best of what is available, a meticulously organized semi-hand-loading system has been developed through the years.

Jan 5, 1964

By Taehong Kim, Carl Pannuti, Nikolas Sokol, Walter Herrick

BACKGROUND This paper discusses work performed as part the rehabilitation of the gravity flow section of the New Croton Aqueduct (NCA) during an approximately two year period between 2004 and 2006. The goal of the project was to restore the gravity flow section of the NCA to optimal operating condition, extending the lifespan of this significant water supply for the New York City metropolitan area. Rehabilitation of the NCA was purposely scheduled before the completion of the new NCA Water Treatment Plant now under construction (Figure 1). The NCA is a 3.73 to 4.34 m (12.25 to 14.25 ft) diameter brick-lined circular andhorseshoe shaped water tunnel constructed between 1885 and 1891. The NCA conveys water for approximately 50 km (31 miles) by gravity and pressurized flow from the New Croton Reservoir in Westchester County, NY to distribution and reservoir points along its alignment, terminating at a distribution station at 135th Street and Convent Avenue in Manhattan, NY. Prominent features of the NCA include a large intake facility at New Croton Reservoir, 38.6 km (24 miles) of gravity flow horseshoe shaped aqueduct, 11.3 km (7 miles) of pressurized flow circular aqueduct, 2 siphons, and 36 open shafts and headhouse chambers which are used as sampling, access and blow-off locations. Until a partial inspection in 1982, the NCA had flowed continuously since its completion nearly 100 years prior. Flow tests have confirmed that the NCA can convey up to 12.7 m3/s (290 mgd) (Figure 2). Cover depths of NCA vary considerably, ranging from a few to hundreds of meters, typically of hard rock. Primarily mined using means conventional for the late1800s, construction of the NCA also employed cut and cover methods in several low-lying sections of the alignment, totaling approximately 1.6 km (1 mile). The NCA crosses through numerous lithologic changes, fault/shear zones and under several significant water bodies including the Pocantico, Saw Mill and Harlem Rivers and the Tarrytown Reservoir. The NCA passes under the Harlem River as a siphon at a depth of approximately 122 m (400 ft) below grade (Figure 3). Soon after construction the Aqueduct Commission Reports on the New Croton Aqueduct documented prominent defects such as large voids behind the lining. More recently, large-scale inspections of the gravity flow section performed during the 1990sand a 2004 inspection of portions of the pressurized sections of the NCA have revealed additional defects such as open and/or deteriorated masonry joints/cracks, leaks ranging from trickles to several liters per minute into and out of the NCA, missing bricks, formed openings, and in one place, a rupture through the liner with discernable

Jan 1, 2007

By Stig O. Olofsson

The problem of overbreak in underground construction and mining is normally approached by a variety of smooth blasting methods. Numerous small diameter, low velocity explosives have been developed specifically for blasting the contour line. Increased mechanization in rock excavation has led to the development of several methods of mechanical explosive loading. A new mechanically loaded smooth blasting explosive was developed in Sweden . However, several limitations were realised, which after several trials resulted in a hybrid smooth blasting method, The Suaer Cautious Contour Blasting Method which will be discussed in this paper.

Jan 1, 1994

By O. F. Brown

The use of quality materials (aggregates and asphalt binder) in optimal proportions is the key to producing optimally performing hot mix asphalt (HMA). The Superpave mix design standard in the US introduced specific volumetric and binder property requirements in HMA design. Different methods for HMA constituent proportioning have been proposed in various guidelines. The design process to determine the HMA blend is currently iterative and engineers rely almost exclusively on experience. This approach is time consuming and often does not result in cost-optimal HMA mixtures. This paper introduces a mixed integer linear programming (MILP) optimization model for hot-mix asphalt constituent proportioning. The MILP model minimizes the total mix cost while satisfying all the volumetric, binder and mix property specification requirements. The model has been successfully validated with real-life example. The aggregates and binder ratios from the model were in close agreement with those from the contractor. The Bailey ratios and the gradation constraints were also satisfied. The cost of the optimal mix was $0.804/Mg less than that of the contractors?. This marginal reduction might make all the difference in an industry that is highly competitive. The MILP model also demonstrated that adding RAP to the contractor?s design would reduce the cost of the blend by $5.74/Mg. The virgin binder content was reduced by 1% because of the recycled asphalt contained in the RAP. This work represents the first successful attempt in incorporating both aggregate and asphalt performance requirements into the optimization formulation. Applying these models will ensure the minimum cost mix that meets all constraints and will increase profit margins for plant operators.

Jan 1, 2012

By G. Gomez Ciments-Calcia

The sources of complaints by neighbours of the operating quarry are due to the 3 following causes : - Impulsional noises or air hoch wawes – Vibrations - D u s t How a blasting in a quarry operation is felt by neighbours cannot be measured solely by the various limits set by national and European regulations regarding vibrations and air shock waves (sound pressure).

Jan 1, 2002

By Éric Poulin, Simon Gariépy, Mario Paredes Malca

"While the design of a control strategy depends on the available process knowledge, its implementation depends on the available process information. On-line chemical analyzers are today widely spread in the mineral processing industry. A real-time concentration measurement of chemical components is valuable information that could bring control strategies to whole new levels. However, the use of these measures rarely reaches anything more than process monitoring. The reason is simple: the on-line chemical measurements quality is most of the time insufficient to be directly included in control strategies. The choice is then made to let the critical eye of the engineer or the operator appreciates the measurements before making any decision based on it.Data reconciliation through mass balance is a technique today widely used in the mineral processing industry to increase the accuracy and the reliability of plant data, mainly for accounting and survey analysis purposes. Real-time data reconciliation of on-line measurements appears as a natural coupling of technologies that could bring new process optimization trends. Once overcome the technical difficulties, full valorization of the instrumentation investment could be reached.This paper presents the application of real-time data reconciliation for process control and performance monitoring. It proposes a general approach, discusses challenges and illustrates concepts with industry experiences."

Jan 1, 2006

In bump-prone coal mines, roof and rib support is subject to dynamic as well as static loading. Although less frequently encountered, the dynamic loading component can result in violent coal expulsions into openings seriously threatening the safety of workers. Dynamic support systems that have been increasingly implemented in many deep hard rock mines for dynamic failure containment have not yet found their adaptation to deep coal mines at desired levels. This paper examines the potential use of some of these dynamic support systems in deep coal mining, particularly in the western United States. Fundamental principles of dynamic loading are reviewed in the context of their application to dynamic failure mechanisms in coal mines. Potential benefits and applicability of the suitable hard rock dynamic support systems are discussed in relation to coal bump mitigation. The resulting insight provides a starting point for development of dynamic support elements for bump prone conditions in deep coal mines.

Jan 1, 2009

The object of this talk is to bring before members the importance of the prospector and the' State Battery system to the wealth and prosperity of the mining industry in particular and the State of Western Australia in general, and to touch on the more important features.Customs plants of any sort are usually subject to a good deal of critioism, usually on the large profits made at the expense of the customer, etc., and this often clouds the real value of the work being done.Prospectors, on the whole, are a good class of men; they work under conditions and difficulties which would deter those less spirited. Food, water and mining supplies are often difficult to obtain and frequently have to be transported great distances. Their mining tools are usually of the most primitive type, yet during last year over 109,000 tons of prospectors' ore were handled by the State Battery system for 73,250 fine oz. valued in Australian currency at over £587,000, the value being 57/- per long ton at par.This production brings the State Battery system into fourth position amongst the producers of the State, the yield being exceeded by the Lake View and Star, Wiluna and the Great Boulder.In passing I might mention that these notes were written at the end of the year 1940, and the above figures were for the previous period. The figures for last year, 1940, were not quite so good, being 101,000 tons for approximately 60,000 fine oz., valued in Australian currency at £572,000.In spite of this drop the State Battery system maintained its position as fourth in order of gold output for the State.The extractions, as a whole, throughout the system, were 92·54%, made up of 68·86% by amalgamation and 23·68% by cyanidation. These figures, for a group of 20 plants treating widely different classes of ore, must be considered satisfactory. The total production since inception is over £11,000,000 in Australian currency.State Batteries are usually more or less of a standard design. Ore is reduced to about 2i in. maximum size before being sent to the bins. Challenge automatic feeeders control the feed to each mill unit, amalgamated copper plates collect the free gold. Corduroy strakes are used with some ores after amalgamation, but in only a few cases has this been found of any advantage to the customer.The pulp from the battery is sampled, after leaving the tables, with a "Tazewell" sampler and pumped to dams for subsequent cyanide treatment.The "Tazewell" sampler is a machine driven by the moving pulp; and takes about fifteen dips per .minute from such pulp through a slotted...

Jan 1, 1941

By Gregory M. Molinda

The Coal Mine Roof Rating (CMRR) was developed 10 years ago to fill the gap between geologic characterization and engineering design. It combines many years of geologic studies in underground coal mines with world-wide experience with rock mass classification systems. Like other classification systems, the CMRR begins with the premise that the structural competence of mine roof rock is determined mainly by the discontinuities that weaken the rock fabric. However, the CMRR is specifically designed for bedded coal measure rock. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, extended-cut evaluation, and others. It has also become truly inter-national, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. This paper discusses the sources used in developing the CMRR, describes the CMRR data collection and calculation procedures, and briefly presents a number of practical mining applications in which the CMRR has played a prominent role.

Jan 5, 2007

By M. Tanaka, K. Aoki, T. Mori, H. Morioka, K. Iwano, T. Kanagawa

To estimate the detailed characteristics of the rock around the cavern during excavation, new monitoring technique for dynamic properties of the rock has been applied. In this paper, micro-seismic monitoring and AE monitoring technique are applied to the excavation of large underground rock cavern and the result was discussed to clarify the acutal behavior of EDZ around the cavern. Zur Einschätzung der Gesteinseigenschaften um die Ausschachtung herum haben die Autoren eine Technik eingesetzt, mit der die physikalischen und dynamischen Änderungen im Gestein um den Schacht während der Ausschachtung beobachtet werden. In der vorliegenden Studie wurde zur mikroseismischen Überwachung ein AE Überwachungsverfahren eingesetzt und die Autoren berichten über die Veränderungen in den Gesteinseigenschaften um die Ausschachtung herum. Dans le but d'évaluer en détail les propriétés des roches qui forment les parois des cavernes creusées, les auteurs ont utilisé une technique de mesure permettant d’observer les modifications physico-dynamiques des roches aux alentours de la caverne pendant son excavation. Dans le cadre de cet article, une technique de surveillance de l’agitation et du bruit microséismiques a été mise en œuvre et les auteurs font état de la modification des propriétés de la roche environnante.

Jan 1, 2003

The 102nd Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 18th August, 1999. Obituaries The President announced the death, during the year, of the following members: Honorary Life Fellows and Past Presidents D.D. Howat Life Fellows O. Deane, J.S. van Zijl Fellow A.A. Hejja Retired Fellows A.L. Forder, C.B. Parker, A.C. Petersen, F.W.J. Ross Members J.S. Stanko, D.H. Gray Retired Member P.K. Bredell Retired Associate I.S. van Eyssen In memory of the deceased and in sympathy with the bereaved, all rose and observed a moment of silence.

Jan 1, 1999

By S. K. Murphy, K. B. Le Bron, A. K. Ward, S. Hayes, T. Rangasamy

A process for evaluating different options for extraction of mining blocks is presented. The process is described and an example of the application of the process to a case study is presented. Un procédé pour évaluer différentes options pour l’extraction de blocs d’exploitation est présenté. Le procédé est décrit et un exemple de l’application du procédé à un cas particulier est présenté. Ein Prozeß für das Auswerten der unterschiedlichen Optionen für die Extraktion von Abbaublöcken wird dargestellt. Der Prozeß wird beschrieben und ein Beispiel der Anwendung des Prozesses zu einer Fallstudie wird dargestellt.

Jan 1, 2003

By M. Sadegh Safarzadeh, Stanley M. Howard

The two-dimensional predominance area (Kellogg) diagram (PAD) surfaces bounding the three-dimensional Cu-As-S-O system were constructed at 900 K. The computations employed gases As4O6(g), O2(g), and SO2(g) as the independent coordinate species to generate diagrams of As4O6(g) − O2(g),O2(g) − SO2(g), and As4O6(g) − SO2(g), while the third gas (As4O6, O2, or SO2) was fixed. The results indicate that there is no shared boundary between enargite (Cu3AsS4) and copper sulfate (CuSO4); however, at PO2 < 10−6 atm, PAs4O6 < 10−10 atm, and PSO2 > 10−4 atm, CuSO4 is the stable phase at 900 K. The chemical driving force for oxidation of intermediate phases between enargite and copper sulfate is substantial except for basic sulfate (CuO · CuSO4).

By W. Burger

In underground mines worldwide, a large number of short and small diameter slot holes need to be excavated. Herrenknecht has developed and built a new boxholeboring machine based on the well-proven Microtunnellingpipe jacking technology. The innovative Boxhole Boring Machine significantly increases work safety and requires only minimal drift dimensions. The high and consistent production rates that can be achieved result in enormous time savings compared to conventional drill and blast excavations. GENERAL ASPECTS In gold, copper and ore mines ventilation shafts are required to prepare block caving operations, to discharge ore onto the transportation level and to provide evacuation shafts. A high level of occupational safety and efficiency is the main objective when drilling vertical or inclined shafts. The faster and more safely shafts can be constructed, the earlier the actual production in the mine can start or be continued. Mechanized or conventional methods (drill&blast) that have been used to date only partially meet the required safety standards and fail to provide the requested production rates.

Jan 1, 2012

By R. Abela

Heavy mineral sands are usually beneficiated in a spiral concentrator circuit prior to separation of heavy minerals into streams of zircon, rutile and ilmenite. The performance of the spiral concentrators is heavily affected by the presence of slimes in the rougher feed. The paper quantifies the effect of slimes content and discusses the beneficial effect of spiral feed de-sliming. The net effect of inefficient slimes removal can cause significant recovery losses of the heavy minerals present in the feed.

Jan 1, 2003

By J. M. Schaekers

In the first part of the article, the authors give a broad overview of the chemistry and some engineering aspects of bioleach processes, eventually leading to the important and critical issue of the stability of arsenic-containing residues, especially those derived from bioleaching of sulphidic gold ores. In the section ?Factors affecting arsenic stability? they give an excellent summary of the factors normally affecting the stability of such residues. This is followed by some valid comments on the suitability of a single leach test to evaluate the long-term stability of solid waste streams. However, they fail to mention that, up till now, no tests procedure has been accepted by either environmentalists or the mining/processing industry as a valid method to test the long-term stability of solid wastes. Their own method is no exception, although, like many others, it is useful to identify potential problems with solid wastes considered for disposal.

Jan 1, 2001