Search Documents

By James C. Patterson

Sintered fly ash was shown to have promise as a modifier for poorly drained soils. Turf grown in mixtures of sintered fly ash and soil benefited from increased water-infiltration rates, greater total pore space, and higher moisture availability, The result was an improved turf stand with increased grass yield and root density.

Jan 1, 1970

A series of gas inrush events occurred during development at Grosvenor mine resulting in exposure to elevated levels of methane at the production face. A total of 22 gas inrush events occurred releasing between 15 and 130 m3 of methane during each event. The presence of an undrained seam in the immediate floor, geotechnical characteristics of the floor, and the stress environment all contributed to these dynamic floor events, while the geological characteristics of the seam below, such as the seam thickness and ash content of 75%, prevented effective pre-drainage. However, events only occurred in headings mined parallel to the principal horizontal stress direction. In cut-throughs (C/Ts) perpendicular to the principal stress direction, no events occurred, and higher methane levels were observed at the production face.

Jan 7, 2020

By K. L. Murphy, G. Multamaki, P. M. Huck

"A preliminary evaluation, based on existing data, has been made of the implications of placing radium-barium sludge in tailings areas. The study was restricted to a consideration of possible increases in the quantities of radionuclides escaping to the environment through either groundwater or surf ace water, considering the types of tailings treated and the effluent treatment systems currently operating in Canada.IntroductionIn the recovery of uranium from ore deposits, the tailings produced by mine/mill complexes are conveyed to impoundment areas in slurry form. After settling, the supernatant is discharged to the environment together with runoff from precipitation on the tailings bas in. Currently, all operating uranium mines in Canada employ barium chloride treatment to control the release of dissolved radium to the aquatic environment. The dissolved radium in the tailings decant is precipitated with barium chloride, forming (Ra,Ba)SO4, and allowed to settle in ponds or lakes. In some instances, settling tanks have replaced ponds and flocculants have been added to aid settling. Because the Atomic Energy Control Board does not consider the precipitation ponds to be suitable for final disposal of these sludges, acceptable sites must be found. Options which have been suggested for sludge management include underground placement either in worked-out mine areas or in special chambers, or placement in the tailings areas. Conceptually, the latter alternative is attractive and probably would minimize sludge handling. This alternative would be subject to the AECB policy which requires that upon abandonment, radioactive releases from a tailings area must be within present regulatory limits and that treatment to meet these limits should not be required in perpetuity.No quantitative data exist concerning either the effect of physical and chemical conditions in the tailings on resolubilization of radium from precipitated sludges or the fraction of this additional radium which would be released."

Jan 1, 1982

In order to ensure safe mining and reduce surface damage in shallow multiple-seam mining, the failure characteristics of interburden strata with different coal pillar offset distances between pillars in the upper and lower seams, the distribution characteristics of stress concentration in coal pillars, and the development characteristics of stratum cracks and subsidence were physically investigated and also using UDEC2D software. Meanwhile, the effect of different coal pillar offset distances on the stress concentration of coal pillars and development of stratum cracks were studied. Based on those results, a formula for safe mining and reducing surface damage was established, which provided a theoretical basis for safe and environmentally friendly mining in shallow multi-seams. According to the results of the study, the optimal coal pillar offset distance (the side-to-side horizontal distance of the upper and lower coal pillars) between the upper and lower coal seams was developed to reduce the stress concentration of coal pillars and surface damage. The results of this study have been applied in Ningtiaota coal mine and have achieved good results in safe and environmentally friendly mining.

Jul 28, 2020

By J Ward, B Rohrlach, B Rosero, J Silva, O Poma

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Alpala copper-gold deposit is a recent, high-grade porphyry Cu-Au discovery located in the Imbabura Province of north-western Ecuador. The deposit lies along the crustal-scale Chimbo-Toachi Fault Zone within the Dagua-Piñon terrane, which is an oceanic plateau accreted to the South American convergent margin in the Late Cretaceous. The deposit is hosted by quartz diorite stocks that intrude andesitic volcanic breccias of the Oligocene to mid-Miocene San Juan de Lachas Formation. Miocene-age calc-alkaline plutonism is associated with porphyry Cu, Cu-Mo and Cu-Au deposits in southern and northern Ecuador. The Alpala deposit lies along a sector of the Miocene arc that has recently been underplated by the Carnegie Ridge seamount chain that induced shoaling of the subducted Nazca plate beneath northern Ecuador.Surface expressions of the deposit were recognised in May 2012 during follow-up of stream sediment anomalies, when outcropping sheeted and stockwork porphyry-related veins were discovered in Quebrada Alpala. The roots of a NW-trending, structurally-controlled lithocap were recognised over an area of 4.5 × 0.9 km. The remnant lithocap exhibits well-defined mineral zonation mapped by TerraSpecTM analyses on grid soil samples. Soil sampling, heliborne magnetic surveying and channel sampling defined initial drill targets.Seven diamond drill holes were completed in the year from September 2013. Drill hole CSD-13-005 intersected 672 m grading 0.93 per cent Cu and 0.91 g/t Au in high-temperature, inner propylitic and locally potassic-altered quartz diorite intrusions. Overlying hydrothermal clay alteration assemblages define the base of the lithocap. A NW–SE trending footwall structure defines the south-west margin of the deposit. Drill hole 5 intersected high-grade sheeted ‘B-type’ and ‘C-type’ veins (Gustafson and Hunt, 1975) that lie along the south-west margin of an 1100 × 500 m magnetic anomaly that is the focus of ongoing exploration.CITATION:Rohrlach, B, Poma, O, Rosero, B, Silva, J and Ward, J, 2015. High-grade porphyry copper-gold mineralisation in north-west Ecuador – The Alpala Cu-Au porphyry discovery , in Proceedings PACRIM 2015 Congress, pp 369–376 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By H. Kotzé

Titania slag is used as feedstock in the production of titanium dioxide pigment. It (titania slag) is the product of ilmenite smelting,a process whereby ilmenite is reduced at high temperature utilizing anthracite as a reducing agent. Although various slag tapping configurations are employed throughout the ilmenite smelting industry, the method of tapping the slag from the furnace into bell shaped cast steel pots, was the subject of investigation in this study. The paper describes the formulation of a cooling model used to calculate and subsequently predict the temperature profile of a slagblock during its cooling within the various cooling environments of pot cooling, air cooling and water cooling. The model was calibrated against actual internal slag temperature measurements and verified with information obtained from both pilot and industrial scale blocks. The paper concludes with solidification results and their practical implication.

Jan 1, 2010

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton, Carla Abarca

"Fine mineral particles are difficult to process by flotation because of their low collision efficiencies with air bubbles. Decreasing air bubble size and increasing mineral particle size through flocculation are the most common approaches to improve flotation efficiencies. Herein we demonstrate that nanoparticle flotation collectors can be engineered to selectively induce fine mineral particle aggregation and promote flotation.Flotation tests of clean fine pentlandite (Pn) and Clarabelle Mill (CBM) rock tails and pyrrhotite (Po) tails that contained significant amount of fine pentlandite have confirmed that the nanoparticles can serve as both collectors and selective flocculants for fine pentlandite. In the case of clean fine Pn, the nanoparticle collectors virtually can float almost all Pn fines. Scoping tests on CBM tails have shown significant improvement in nickel recovery. Addition of nanoparticles as a flotation aid can recover 20% of the nickel contained in the rock tails and 40% of the Pn contained in the Po tails compared to current mill operations giving 0% nickel recovery from rock tails and no Pn selectivity from Po tails. Ongoing work includes attempts to identify optimal strategies for employing nanoparticles in fines flotation.IntroductionFine particle flotation is an industry-wide challenge in mineral processing. Fine mineral particles are difficult to process by flotation because fine particles have low mass and thus low momentum, which results in their low collision efficiency with air bubbles (Dai, Fornasiero, & Ralston, 1999). In addition, fine particles have not only high specific surface area but also more active surface area, which causes high reagent consumption. For base metal sulphide minerals, particle size between 10 µm and 70 µm is a typical range where high flotation recoveries can be achieved with conventional flotation chemistry and acceptable cell residence times. For pentlandite, the flotation recoveries decrease sharply when the particle size is below 10 µm and hydraulic entrainment is the dominant mechanism, giving recoveries proportional to water recovery and no Pn enrichment. (Jameson, Nguyen, & Ata, 2007)"

Jan 1, 2015

By D. Laguitton, D. Hodouin, V. K. Gupta, R. Spring

"The CANMET SPOC project aims at inducing progress in process evaluation and optimization by developing user oriented software based on state-of-the-art theory. The present work is the result of a joint effort by CANMET, Noranda Mines and Université Laval to develop two computer packages: one (RTD) to calculate the residence time distribution that best describes the material transport through the mill, the other (FINDBS) to estimate the rate of breakage and distribution function of the population balance model in a ball mill. The RTD package can handle data from various experimental methods (impulse or complex tracer feed, with or without recycling, etc...). The FINDBS package provides options for the functional description oj both model parameters Band S. The full detail of the methods and programs appears in a users guide. The program capabilities and several sample runs are presented.IntroductionSimulation of mineral dressing operations by computer has been largely contained within academic and research circles and has not yet gained a status of routine practice in the ore and coal industries. It is however a matter of time before process simulators are available on every process engineer's desk to assist process optimization tasks, flowsheet design and professional training. The CANMET SPOC project (Simulated Processing of Ore and Coal) was initiated in 1980 to assist the Canadian industry in integrating computer-based methodology for process evaluation and optimization(1). Software development, documentation and transfer is one of the main priorities of the project which will mature in 1985 by releasing a complete package of manuals and programs covering sampling, material balance computation, unit modelling, flowsheet simulation and optimization . This paper is a condensed description of a typical project element in its 1982-1983 state of development. The required methodology for ball-mill modelling and simulation was consolidated an d merged to other project elements during a joint study under contract financed by CANMET and Noranda Mines Ltd . The first part of the study dealt with documenting experimental methods and software for ball-mill computer simulation. Université Laval GRAAIM (Goupe de Recherche en Automatistion Appliquée à l'Industrie Minérale) acted as sub-contractor for this part of the study(16,17). A second part dealt with applying the model calibration techniques to a large industrial data base and is reported elsewhere(2,18,19)."

Jan 1, 1984

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the conserva¬tion of important raw materials and the utilization of solid waste. Two of the objectives are to conserve high-quality coking coals used for foundry coke and to utilize waste materials of marginal quality but of high calorific value. These objectives are consistent with Bureau goals. Pilot plant cupola trials were made to evaluate the adequacy of various alternative fuels, and to determine to what extent they could replace the foundry coke in cupola charges. Information was obtained on furnace performance, metal and slag chemistry, environmental questions, and the properties of castings. It was shown that anthracite or bituminous coals can partially replace charge coke up to the 40 pet level. Briquetted materials prepared from fuel fines, and waste prod¬ucts or byproducts of high calorific value, all tend to break down on heating in a cupola so that their use must be restricted to below 20 pet replacement. In cases where pitch-bonded coal fines or petroleum coke were used, carbon pickup by the iron was inadequate for gray iron specifications. Although emphasis during this work was placed on basic slag practice, some acid practice results are included.

Jan 1, 1980

One of the seminal pioneering papers in reserve evaluation was published by Danie Krige in 1951. In that paper he introduced the concept of regression techniques in providing better estimates for stope grades and correcting for what later became known as the ‘conditional bias’. In South Africa, the development of this approach led to the phenomenon being dubbed the ‘regression effect’, and regression techniques ultimately formed the basis of simple kriging in Krige’s later papers. In the late 1950s and early 1960s, Georges Matheron (1965) formulated the general theory of ‘regionalized variables’ and included copious discussion on what he termed the ‘volume-variance’ effect. Matheron defined mathematically the reason for, and quantification of, the difference in variability between estimated values and the actual unknown values. In 1983, this author published a paper that combined these two philosophies so that the ‘regression effect’ could be quantified before actual mining block values were available. In 1996 and in some earlier presentations, Krige revisited the regression effect in terms of the conditional bias and suggested two measures that might enable a practitioner of geostatistics to assess the ‘efficiency’ of the kriging estimator in any particular case. In this article, we revisit the trail from ‘regression effect’ to ‘kriging efficiency’ in conceptual terms and endeavour to explain exactly what is measured by these parameters and how to use (or abuse) them in practical cases.

Jan 1, 2015

By H. L. Anthony, A. C. Richardson, G. D. Coe

"INTRODUCTION The Warrior View mine of the Seaboard Coal Corporation is located in Tuscaloosa County on the Warrior River about 14 miles northeast of Tuscaloosa, Ala. The Brookwood bed at this point yields a coal with fair coking qualities, and the product from neighboring mines on this bed has been used for the manufacture of blast furnace coke. The output of the Warrior View mine, however, is used exclusively for domestic and steam-raising purposes.This paper continues the series° of reports on the washability of Alabama coals which are based upon the study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal mining companies. This paper contains screen-sizing and float-and-sink tests of a representative sample of run-of-mine coal, and flakiness and crushing tests on certain sizes.Published information on the Brookwood bed is very meager. Fieldner6 gives the proximate and ultimate analyses for a number of seam samples taken from representative mines working this bed. Gandrud and Britton7 show sections of this bed taken at Searles, Ala. They also give the specific gravities of the coal, the bone, and the shale partings.Table 1 give the proximate and ultimate analyses for the 3/4 to 3/16 inch size of raw coal. Table 2 gives the sulphur content and the ash fusibility temperatures of the float-and-sink fractions for this same size. The character of the coal is very uniform throughout the range of sizes produced and, as it was not convenient to have these analyses on all sizes, this size was chosen as being representative of the coal. From the information available it is evident that the coal preparation problem is restricted to one of ash reduction.SAMPLING AT THE MINEAt the Warrior View mine the run-of-mine coal is dumped from the mine cars upon a 3-inch grizzly. The oversize is crushed in rolls set at 24 inches and joins the undersize before being elevated to the raw-coal bin ahead of the jig. The sample was caught at the point where elevates discharges into the raw-coal bin, by taking a proportional amount of the coal at 10-minute intervals over the period of a day's run, The total sample amounting to 2.7 tons was shipped to the laboratory at Tuscaloosa for the washability studies."

May 1, 1932

By J. E. Crawshaw

"The few previous observations of the effect of turbulence on limits of inflammability have been made on a small scale in turbulence produced either by a fan or by movement of the mixture.By a suitable amount of turbulence from a fan the lower limit of methane was 5 per cent as compared with 5 per cent observed for quiescent mixtures in the same vessel.3 With a streaming movement of the gas mixture within the range of speed from 35 to 65 centimeters per second (69 to 128 feet a minute) the lower limit was approximately 5 percent,4 For a quiescent mixture of ethane the lower limit was 3.10 per cent ethane, but with fan running at a moderate speed a 3 per cent mixture exploded.5The object of the tests herein reported was (1) to determine the lower limit of natural gas in a mixture of natural gas and air Which would be ignited and propagate violently when the turbulence was produced by explosives fired from a cannon into the mixture; (2) to observe the behavior when the mixture contained less than this low limit; and (3) to determine how turbulence produced by a fan affects thin limit.Four series of tests were run, three of which were to determine the effect of different sources of ignition: Tests with (1) an electric igniter; (2) 3F black blasting powder stemmed with 2 pounds of dry fire clay stemming used to ignite the mixture, and (3) 40 per cent straight nitroglycerin dynamite unstemmed. The fourth was made to study the effect of turbulence produced by a two-speed electric fan, using an electric igniter as the source of ignition.In both series of tests with explosives, charges of 50 and 200 were used to determine the effect of increased quantity of explosives on the lower limit of natural gas."

Jul 1, 1930

By Paul J. O'brien, George N. Neary

"The base metal mine at Buchans, Newfoundland, has been producing since 1928. For many years, mill tailings were disposed of by dumping into a nearby natural watercourse via which they were transported to Red Indian Lake and deposited. In 1965, environmental concerns prompted the establishment of settling ponds near the mine site. Effluents fed to these ponds included slimes washed from mine backfill sand and waste water pumped from underground as well as mill tailings. Dusting around the perimeter of the ponds was first observed around 1970and within a couple ofyears reached serious proportions. A program to alleviate the condition by developing a vegetative cover over the tailings was commenced in 1974. The work was successfully carried out and demonstrated that the large area of waste could sustain a permanent cover of grasses.This paper outlines the experimental work done at Buchans as well as the procedures followed and the problems encountered in carrying out full-scale revegetation."

Jan 1, 1981

By Annie G. Smelley

As part of its program to develop technology that will encourage maximum utilization of the Nation's mineral resources, the Bureau of Mines conducted research on debrining potash-clay waste slurries by means of flocculation with a high-molecular-weight polymer and subsequent solid-liquid separation on a rotating trommel screen. In laboratory batch tests, potash-clay waste slurries were consolidated from initial clay contents of 8 pct to final contents of 30 pct with a polymer dosage of 1.2 Ib/ton of dry clay waste. Small-scale continuous tests yielded debrined products containing 20 pct solids using a polymer dosage of 1 Ib/ton of dry clay solids.

Jan 1, 1983

By K. J. Griffin, G. W. Rosval

"In our increasingly competitive market, attempts to improve productivity by increasing axle loads have placed more severe demands on rails. CP Rail thus requires stronger, tougher, and more wear-resistant rails from steel manufacturers. The choice of any rail steel is always a compromise between technical and economic factors. The technical assessment of a candidate rail consists of laboratory and field testing. Laboratory evaluation of rail steels cannot adequately model many service conditions and must, therefore, be supplemented by long-term field testing. The field testing conducted on CP Rail is the subject of this paper.Long-term, in-track, assessment of candidate rail steels begins with the selection and re-laying of a test curve representative of the intended service with both the candidate rail and a control rail steel (i.e. the present intermediate or premium rail standard). The wear performance of the candidate rail is evaluated, in relation to that of the control rail, using data obtained with a rail profilometer developed by the Research and Development Department of CP Rail. Qualitative observations are also periodically made to evaluate the relative susceptibilities of the two rail types to surface defect formation. Testing continues until stable metal loss patterns are achieved. Relative life predictions are then made and detailed monitoring of the test site is discontinued.CP Rail's in-track assessment program for premium rails has resulted in the establishment of a new CP Rail premium rail standard - low-alloy, head-hardened, rails have replaced high alloy rails. The wear/fatigue lives of these new premium rails exceed those of our previous standard by more than 50%, and they also exhibit excellent weldability. CP Rail will continue to evaluate new premium and intermediate strength rail products."

Jan 1, 1988

By Sam S. Taylor

In most oil fields, natural gas is the major source of energy causing flow of oil to the well. The amount of gas produced With the oil generally exceeds actual energy requirements, so that in time the gas reserve of the field becomes seriously depleted and the oil production nest be stimulated by some auxiliary means. One of these is to repressure the oil formation with natural gas; or, where a gas supply is not available, often air is used. Although air is a cheap and convenient repressuring medium, its use sometimes is attended with several disadvantages. First, the return air-gas mixture decreases rapidly in fuel value, often until it can be used no longer as a source of power. At the same time, explosive mixtures may result if recycling is used, causing hazards to life and equipment. Second, some fields experience considerable trouble with the formation of emulsions which become increasingly difficult to treat. Although there is no definite proof that air repressuring always causes these emulsions, many operators are convinced that this is the case.

Jan 1, 1934

Two small coral islands in the Pacific Ocean, situated close under the equator, and formerly classed among the Line Islands, have, during the last three or four years risen into prominence owing to the valuable deposits of phosphate of lime discovered on them.The deposits of Ocean and Pleasant Islands are under the control of the Pacific Islands Company (1902) Limited, of London and, Sydney, and the high grade of the phosphate, together with the exceptionally favourable facilities for mining this mineral, of which there are several millions of tons on these islands, give this company advantages which enable them to command the Australian and New Zealand markets, and also to make large contracts with Japan and other countries. Both islands, as far as surface indications are concerned, are entirely constructed of coral, with phosphate on the top from the highest points to the present sea level, there being no sign of volcanic rocks, with the exception of a few pieces of drift pumice on the coast.Banaba (Paanopa according to. the Admiralty charts), also known as Ocean Island, was discovered in 1804. It is situated in lat. 0° 52" S. and long. 169P 3[)" E.

Jan 1, 1904

By B. S. Terry, C. L. Harris

After measuring the kinetics of Ni reduction from a SiO2-saturated fayalite slag into a Cu-based metallic phase on a laboratory scale, a general model was developed that is capable of simulating mass transfer to and from metal-slag, slag-gas and metal-gas interfaces for multiple species. The model was used to simulate the reactions that occur when Cu and Ni are reduced from fayalite-based slags into a Cu-based metallic phase. Good agreement was achieved between model predictions and experimental data

Aug 1, 1995

By P. Chaddock

The Thompson Mill has a capacity of 15,000 T ID of ore and produces two grades of nickel concentrate, copper concentrate and occasionally graphite concentrate. Up to July of 1985 we processed two distinct ore types: T-1 ore, averaging 2. 8% Ni and . 2% Cu and Pipe Open Pit ore, averaging . 8% Ni associated with peridotite and serpentine. Presently our ores from T-1 mine and Thompson Open Pit are of the same type and are processed together. (Figure 1)! n October, 1982, we decided to install an Outokumpu Courier 300 on-stream analyser on an initial 6 streams. The equipment was delivered to the mill on May 2, 1983 and the first analyses were generated by June 17th. The calibrations were 35% complete by the mid-July summer shutdown and were completed in the fall. 1. 2 Analyser Slurry Feed System:The key to successful on-stream analysis is delivery of the sample streams to the analyser.Our system uses pressure-thief sampling for collection. (Figure 2) Initially we used thief samplers modelled after the Outokumpu design, with turbulence bars upstream of the collection point. These units have been replaced with simple laterals as they have worn out. Our thief samplers are mounted vertically on pump discharges and we believe sufficient turbulence exists to ensure representative sampling.

Jan 1, 1987

By Larry F. Drolet

Charleston, SC is anything but boring. The city was founded in 1670 and has played a significant role throughout the history of the United States. Located along the coast of the Atlantic Ocean in the southeastern United States, Charleston was a vital city in America?s early existence. Charleston?s coastal location has helped the city become the fourth largest cargo port in the United States and earn the 2011 designation as the number one travel destination in the United States by the Conde Nast Traveler Magazine. Part of Charleston?s charm and beauty can be attributed to its historic structures and churches that line nearly every sidewalk, roadways that were laid out based on the width of horse carriages, great weather, southern hospitality and coastal living. Now imagine the challenges of installing new, or re-placing aging infrastructure, in this setting. Every shovel full of dirt, every stick of pipe and every roadway sub-surface has its own historic story to tell. For engineering minded individuals, Charleston?s infrastructure has almost as fascinating a history as its more visible surface structures. Charleston was among one of the first American cities to construct separate sanitary and storm water drainage infrastructure. This concept has roots dating back to the city?s founding and is a credit to the foresight of its founding fathers who understood the basic health differences between sanitary and storm water.

Jan 1, 2013