Search Documents

The large increase in secondary industries in this country, during the war and post war periods, has caused a shortage of capacity for the production of merchant bar.To overcome this shortage, an expansion of rolling mill facilities has been undertaken by the Broken Hill Pty. Co. Ltd. A small, but modern, merchant mill has been erected at Kwinana in Western Australia and a strip and skelp mill is under construction at Newcastle. The latter mill will roll strip and skelp at present being rolled by the Newcastle 10 in. Merchant Mill, enahling this mill to concentrate on merchant bar production.The Kwinana mill was installed to supply the Western Australian market. This state has a small population (approximately 658,000) and is not at present highly industrialised. It was necessary, therefore, to design a mill which would be capable of producing a wide diversity of sections and could be expanded as the demand increased. To begin with capital expenditure had to be kept within reasonable bounds. The design work for this mill, with the exception of a few specialised items of equipment, was carried out at Newcastle.All design work for the Newcastle mill was carried out by the lVIorgan Construction Co. of America. Although initially intended for rolling flat. products, the designers were asked to make the mill as flexible as possible, so that should the market for flat products decrease, this mill with additional equipment could undertake the rolling of medium sized sections.

Jan 1, 1957

By V. K. Kollipara

Air flow patterns in the face area of a room-and-pillar mining are critical for understanding the dust dispersion characteristics and for developing engineering controls. SIUC has previously performed a CFD study to analyze the airflow patterns in the face area when continuous miner is making a straight cut. Results from this study identified low air velocity and re-circulation zones in the face area and illustrated the significance of line curtain, and scrubber operation on the air flow patterns. This paper discusses similar analyses when continuous miner is making a right turn cut as it is considered to be the dustiest cut among all the cuts made to advance an entry through a crosscut. This paper presents results for box-cut development for a right hand turn x-cut. This paper also addresses line curtain advance and air leakage through the curtain on the airflow patterns in the face area for such a cut. Low air velocity and recirculation zones were identified by analyzing the velocity vectors.

Jan 1, 2012

By P. H. Carr, G. G. Marino, K. A. Patel

Extensions to a correctional institution at Wabash Valley, Indiana, required development over abandoned coal-mine workings, at 90 m depth, where subsidence was possible at surface. Backfilling of the flooded mine in critical areas was determined to be the most cost-effective method of limiting the risk of damage to the buildings. Containment grout was first placed in selected entries and cross-cuts of each mine area; the remaining volume was then filled with a readily flowing infill grout. Where a high proportion of an area was taken up by rubble, calcium lignosulphonate was used as a retarder and plasticiser to increase penetration. Grout movement was monitored from adjacent boreholes with an electrical resistivity probe during grouting, while after the work was finished core samples were obtained from verification holes drilled in the backfilled areas

Jun 19, 1905

The estimation of the spatial variation of the b-value of the Gutenberg- Richter relationship is important for both the general interpretation of the mechanism of rock mass response and seismic hazard assessment. The interpretation of b-value as a parameter of rock mass response is discussed in this paper. The methods applied to evaluate the spatial variation of b-value and the algorithm for obtaining the magnitude of completeness and b-value for subsets of data are presented with some verification analyses. The algorithms presented enable the automation of a spatial evaluation of b-value.

Jan 1, 2014

By S. Henley

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993 (original title: The database: a pre-requisite for large-scale use of AI in mining). Artificial intelligence is a term which has been widely applied to different techniques including rule-based systems using inductive and deductive logic algorithms, neural networks, learning systems and genetic algorithms. In principle it should be applied to adaptive statistical techniques. Some of these applications have been coded in languages which are specifically suited to the novel requirements of AI but are not easy to integrate with more traditional computing methods. Efforts have been made to bridge the gaps, particularly with database management systems and such efforts at integration should provide the key to future success in the application of AI. A field which has been termed "knowledge engineering" cannot be credible as such if it fails to provide easy access to raw materials of "knowledge" i.e. the data residing in databases. In the mining industry there are a number of significant areas in which AI could usefully be applied throughout the industry, but its advance is slow because of the lack or inefficiency of such database links. Current development of object-oriented database systems for geology and mining holds out hope for such integration in the foreseeable future

Apr 1, 1994

The Aredor mine employs conventional dragline methods to exploit alluvial diamond deposits. Production began in 1984 with the policy of mining in the terrraces during the wet season and in the river flats during the dry season. Early production failed to meet predicted grades. A major geological programme to re-evaluate existing reserves was undertaken. This resulted in considerable increases in reserves in the river flats. Many of the reserve blocks included flats on both banks of the Baoule river. Methods of access into the river flats, normally flooded in the wet season, were developed to allow mining throughout the year. River diversions have been the main method used to provide access into the reserve blocks and, most importantly, to remove the risk of flooding. Aredor has carried out six main river diversions with a total length of 12 km. The diversions allowed production planning to be made on the basis of the economic evaluation of the reserve blocks, without undue regard to natural ground conditions or to seasonal factors. The Manning equation was used for the calculation of channel dimensions and gave satisfactory results. The practical aspects of the diversion preparations and flooding prevention are described

Sep 1, 1991

By R. G. B. Pickering

The purpose of this report is to chronicle the interaction between Anglo Platinum and Sandvik Tamrock during the development and application of Long Hole drilling as a viable, practical method of narrow reef mining. Appendix I identifies the people from Anglo Platinum and Sandvik Tamrock who participated in the project. Experiments in long hole drilling and blasting were conducted in a number of mines during the late 1950s and early 1960s. Some of the advantages envisaged were: ? The face would require no daily examination ? No barring down or immediate face support required ? No sockets to clean ? Only a few well drilled holes rather than large numbers of short blast holes ? Avoidance of poorly-marked holes, inaccurate drilling and improper charging ? Better supervision and better face advance. Holes 50 mm in diameter were drilled parallel to the stope face by pneumatic rock drills from advance strike gullies. Holes were charged with amon gelignite cartridges. All holes were traced with detonating cord to ensure propagation of the explosive along the entire hole length. Rock was blasted onto a rolling scatter pile. A number of reasons have been cited for the failure of this mining method. The two most important were: ? problems in controlling hole deviation which was exacerbated by the fractured ground ? difficulty of charging up holes in fractured ground, due to relative movement of rocks along fracture surfaces over the hole length. The idea of drilling a few long holes parallel to the face rather than a large number of short blast holes perpendicular to the face was an attractive option to mechanize narrow reef mining. This particular project started in 1998. Initial trial The Union Section of Anglo Platinum purchased a Solo H 606 RA long hole drilling rig from Sandvik Tamrock in 1997. In order to evaluate long hole drilling as a basis for face mechanization. The Solo series of drill rig was selected because it combines high drilling performance and good drilling accuracy with high versatility with a compact size. The mining method proposed by a consultant to Anglo Platinum was based on the current trackless mining method practised by Union Section. The trackless mining method is better described as a trackless development and transport method. Reef strike drives were installed approximately 40 metres apart on dip using trackless equipment. Reef was mined using hand-held pneumatic rock drills and scraper winches and the excavation was supported by sticks and crush pillars at the top of the panel. Rock scraped from the panel was loaded by Lad Haul Dumps (LHDs), trammed to an inclined haulage, and loaded into trucks for transport to the surface. It was intended that the Solo would drill from the bottom advance strike drive to the top advance strike drive. Blasted rock would still have to be scraped from the panel. It is also difficult to understand how well the support would have survived. In the initial motivation it was stated that drilling accuracy was of the utmost importance. Previous work by Sandvik Tamrock had shown that, in other parts of the world, 20 metre long holes could be drilled with a deviation not exceeding 100 mm provided that: ? holes were collared with low thrust pressure ? operating percussion pressure was kept low -often not ? exceeding 10 MPa ? drilling was to be with tubes, not rods. In early 1998 initial trials with the Solo H 606 RA were inconclusive; attempts were made to drill 40 metre long holes from one advance strike drive to another. Difficulty was experienced in measuring hole straightness and accuracy, there was no survey of the holes, and no blasting was done to expose hole barrels. A long hole mining system was then defined, with a corresponding face mining system, which led to the design of a test programme for the Solo drilling rig. Earlier experience at Telfer The proposed face mining system was based on a mining method that is practised at Telfer Gold Mine in Western Australia. Telfer has a series of domed reefs that dip at angles of less than 20° to more than 40°. The ore bodies are all thin, with widths from 0.6 metres to 0.8 metres. Figure 1 shows the face layout. Experience at Telfer indicated the following: ? The spacing and size of the dip pillars should be based on the rock mechanics of Union Section ? The length of the face is determined by the ability to correctly position the blast holes. Positioning of blast holes is a function of hole straightness and hole direction. Blast holes in Telfer were drilled 64 mm diameter with retrac bits from Sandvik. Extension steel was T38 by 1.8 metre lengths. A guide rod was fitted immediately behind the bit. To achieve greater accuracy' operators drill at relatively low percussion and thrust pressures. Results show that very good accuracy is achieved in 20 metre stopes and only fair accuracy in longer stopes. In 34 metre long stopes 10-15% of the holes are not sufficiently accurately positioned and have to be re-drilled. All blast holes are

Jan 1, 2006

By Milner A, Brockway D, Hodges S

The combustion of brown coals in Latrobe Valley power stations produces approximately 500 000 tonnes of solid wastes each year. This material, which includes precipitator ash, char and furnace ash, is hydraulically sluiced to large ashing ponds and the supernatant solution is ultimately discharged to the sea. There are significant operational and capital costs associated with the current ashing system. The ash produced from the Latrobe Valley coals is unique and has a wide variety of potential applications including soil conditioning, concrete and cement extenders, fillers in non-metallic materials, components of building products. In addition, with the application of appropriate technology, it is possible to extract char, sodium sulphate, calcium carbonate and magnesium metal (as the chloride) in substantial quantities from the ash. Research has been carried out to explore the prospects of these various options for ash utilisation. The research has focused on detailed characterisation of the ash material and the potential extraction efficiency for various species under various conditions. From this work a conceptual process has been developed and subsequent studies have been directed towards understanding variables and optimising operating regimes for product extraction. Currently, the work is concentrating on the separation of char, the development of high-grade carbon products and the extraction of sodium sulphate.

Jan 1, 1992

By A. M. Milev

A stand-alone instrument especially designed for recording strong ground motions was used in this study to create a large data base of peak particle velocities measured on stope hangingwalls. A total number of 58 sites located in stopes mining the Carbon Leader Reef, Ventersdorp Contact Reef, Vaal Reef and Basal Reef were monitored. The peak particle velocities were measured at the surface of the excavations to identify the effect of the free surface and the fractures surrounding the underground mining. From the monitoring results obtained, the velocity criterion of 3 m/s will bean adequate value that support systems have to sustain during a rockburst in most cases. However, PPVs in excess of this criterion were recorded, and some PVDs were damaged or irretrieveable, a consequence of which was that possible extreme events were not recorded. The data recorded on the skin of the excavations were compared to the data recorded by the mine seismic networks to determine the site response, defined as the ratio of the measured peak ground velocity to the peak ground velocity inferred from the mine seismic data. The site response measured at all mines studied was found to be 9 ±3 times on average. Values of the site response did not vary significantly with seismological parameters such as peak ground velocity, hypocentral distance and source radius.

Jan 1, 2005

By V. Krupa, E. Lazarova

A method is proposed for the continuous calulation of a rock mass in real time while tunnelling with a TBM. Rock properties are investigated through models of the fracture stress under the disc cutters, the quasi-shear stress between the disc cutters and the specific energy of cutting under the disc cutters. Comparison of theoretical and monitored data of cutting specific energy can be used to determine theoretically the prevailing shape and size of the bulk debris. The shape and size of the chips from a given rock vary with the boring parameters. Introducing shape and volume corrections into the models of the evaluated stresses suppresses the influence of the boring regime and allows the rock properties to become dominant

Dec 1, 1996

By Natalya. N. Ankusheva

The problems of ore-bearing palaevolcanic structures in folded belts are actual because of their high productivity in nonferrous, ferrous and noble metals ores. Now relationships of location and conditions of formation for sulfide-massive and gold-bearing deposits are investigated very well in Urals. But carboniferous sulfide-barite mineralization, for example the barite veins in Arcaimsky palaevolcano are?nt studied enough now [3-5]. The purpose of this research is the studying of mineralogy and thermobarogeochemistry of barite from the hydrothermal veins. It will allow to determine the conditions of its formation and to compare it to the similar mineralization of others ore types.

Jan 1, 2006

THE Phillips River gold and 'copper field is situated on the south coast of Western Australia, about 200 miles east of Albany, 180 miles west of Esperance, and: 250 miles south of Southern Cross, forming the southern extremity of what Mr. H. P. Woodward classes as the fourth belt of Pre-Cambrian rocks, and the first auriferous belt, whicf extends northward through Southern Cross, Mount Magnet, and Cue. The field may be considered the premier copper producer of the State. The first mineral discoveries were made about 1892; when gold, copper, and iron pyrites were found; but, owing to the isolation of the district and the scarcity of water, both in the locality and on the route thereto, little work was done for some years. In1899, however, payable gold reefs were opened up, and the district began to attract attention.The southern portion of the district is composed of limestone and sandstone rocks, forming the coastal series, and is for the most part flat, broken only by a few low hills and ridges, except to the west, where Cape Barren and Eyre's Range stand out...

Jan 1, 1917

By Fulton Flick

THE micrography and macrography of aluminum and its alloys present certain difficulties. Many of the difficulties attendant on the micrography have been removed by methods developed during the past few years, notably those of E. H. Dix, Jr.1 The development of grain size in aluminum and its alloys may be equally troublesome, yet comparatively little detailed attention appears to have been given to it. Satisfactory reagents. are available for the development of such structures in ferrous and most non-ferrous metals, but those applied to aluminum and its alloys, i. e., alcoholic or aqueous solutions of sodium hydroxide or hydrofluoric acid are not entirely satisfactory. Hanson and Archbutt,2 in speaking of these two reagents, state that "These two reagents give fairly satisfactory results, but they sometimes produce badly tarnished surfaces from which the surface deposit is difficult to remove." It has been our experience that neither of these reagents is to be entirely relied on for developing structures suitable for study or photography. This means that when the etch fails to produce satisfactory results the, specimen must be repolished, through the 000-paper at least, and then etched with another reagent. This procedure entails a con¬siderable loss of time, and the final results may not be all that might be desired. However, the reagent to be described, although not a panacea for all etching troubles, has improved results so markedly that it is felt that it is worth offering as a grain-size etch generally applicable to aluminum and aluminum alloys. Czochralski3 in 1915 mentioned the application of a solution of 10 to 20 c. c. concentrated hydrofluoric acid in 100 c.c. absolute alcohol, etching in this reagent being followed by dipping in concentrated hydrochloric-acid solution.

Jan 2, 1925

By Paul Gauthier

Aujourd?hui, avec un faible prix de l?or sur le marché, les opérateurs miniers doivent revoir leur façon de faire. La méthode de minage «Eureka» permet de réduire les coûts de production et d?accélérer la mise en production des chantiers. Les principales étapes du cycle de minage et les problématiques associées à l?utilisation de cette méthode à la Mine Bousquet y sont décrites.

Oct 1, 2001

In several of the States of Australia, mining on private property has been seriously hampered by the fact that large areas of land have been alienated from the Crown before the discovery of gold or other minerals. In Western Australia this difficultyhas only occurred to a small extent, and has largely been overcome by an act entituled "An Act to Permit Mining on Private Property, No. XXIX., 'October, 28th, 1898." Under this act, the holder of a miner's right can apply for a gold mining lease on private land; such applicant may treat privately with the owner of such land as to the amount of compensation to be paid for surface ,damage, or the case may be brought before the Warden who will assess the damages. Private land used as a garden, orchard, or vineyard is exempt from lease, unless the applicant has authority from the owner, or such lease is limited to a greater depth than 100 feet from the lowest part of the surface.No lease shall be granted of any mines under any private land in any municipality unless either the applicant has authority from the owner, or such lease is limited to a greater depth than two hundred feet from the lowest part of the surface.The same regulation applies to leases of private land on which any hospital, asylum, or public building is situated or under or within one hundred and fifty yards laterally of any...

Jan 1, 1901

By W. L. Thayer, K. A. Jonasson, R. D. Coleman, J. D. Hazlett, C. E. Capes

"Loss of coal fines in reject slurries limits the yield of coal cleaning operations. Difficulties in handling fines also limit the extent of physical cleaning in treating coals with finely-disseminated impurities. Selective oil agglomeration allows even extreme fines to be processed and offers some novel approaches for coal cleaning and utilization.The oil agglomeration process for the recovery and beneficiation of fine and ultrafine coal has now been commercialized by the Chemical Engineering Section/Chemistry Division of the National Research Council (NRC). This paper describes these activities to apply oil agglomeration and related fine coal technologies on an industrial scale. Pilot plant and large scale results are described, as well as aspects of agglomerate utilization in both wet and dry form."

Jan 1, 1988

By J. C. Kerkering, S. M. Miller, P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown's modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers' Z, measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 1993

By C E. Vidal

Geological exploration and mining development increased their intensity and rate of success during the last five years in Peru. Particularly relevant are the mining projects of Yanacocha and Pierina for epithermal Au and Ag. Also relevant are the new mining operations at Iscaycruz and Uchucchacua for limestone replacement Zn- or Ag-rich base metal skarn deposits. Miocene continental volcanics host the low-grade but near-surface orebodies of the Yanacocha mining district in Cajamarca. Several deposits have been mined since 1994 with open-pit and heap-leach gold production increasing from 300 000 ounces to 1 300 000 ounces in 1998. In a similar geological setting, but with three times the grade of Yanacocha, the Pierina valley-leach operation in Ancash is set to produce 800 000 ounces Au during 1999. At Iscaycruz in Lima, Cretaceous limestones host massive pyrite and sphalerite skarn deposits with 10 to 20 per cent Zn. Mining and milling were started in 1996 with last yearÆs production rising to 180 000 tonnes of Zn concentrates. At Uchucchacua, selective underground mining of fracture-controlled Ag skarns, with 400 to 420 g/t, has been recently increased from 1200 to 2000 tonnes per day to produce 5.5 million ounces Ag during 1998. Advanced exploration projects are located in the framework of nine Phanerozoic metallogenic provinces. Mineral deposits of preferred attention are precious metal disseminations and veins, base metal replacements and skarns, porphyry Cu (Mo-Au), Mississippi-Valley-type Zn and base metal volcanogenic massive sulphide deposits. Geological discovery of new orebodies enables a sustainable development of the mining industry in the country.

Jan 1, 1999

Structurally- controlled deep leaching processes have removed vast quantities of carbonate from a substantial portion of the "silica-dolomite" enclosing the 500 copper orebody. Mine drainage subsequently allowed free access of air to the porous environment created and oxidation of sulphides commenced. During the mIne development stage the exothermic and temperature-dependent nature of these hydrolysis reactions resulted in a slow general elevation of ground temperatures. and levels of 90 - lOO°C were attained in restricted moist sulphide-rich areas.With the advent of production and extensive use of explosives, the oxidation processes were locally raised to new levels of activity. Direct interaction of explosives and sulphides in favourable conditions caused temperature rises to above 260 C. Above this point the dry oxidation of sulphides in air was initiated and rapid escalation to the vicinity of 800 C has been known to occur in isolated cases.Ground reactivity is a function of the complex interrelationship of several controlling factors and no simple index exists.Control techniques are presently aimed at prevention of temperature rises in the range 100 -260 C. Inhibition of the rapid dry oxidation processes above 260 C is difllcult and current efforts have met with only partial success.

Jan 1, 1968

By Alvin Kaufman

To aid industry and Government in planning water developments the Bureau of Mines in 1963 canvassed mineral producers to determine water use in 1962. Water use by the mineral industry comprises only 2 percent of the water withdrawn by industry as a whole. The major water-using mineral industries are natural gas processing, phosphate rock, sand and gravel, and iron ore. Analysis indicated the following conclusions: 1. Total water use and new water intake is dependent on the quantity of material processed and the process water requirements of the particular industry or commodity. 2. Recirculation is dependent on the processing requirements of a particular commodity, the manner in which the water is used, cooling and condensing requirements in certain large industries, the quality of new water intake, and the need to treat new and discharged water. 3. Consumed water is dependent on the quantity of water recirculated, the temperature and humidity in the area, and the proportion of water used for cooling and condensing. 4. A threefold increase in water use by the mineral industry by 1985 is forecast

Jan 1, 1966