Search Documents

"Located in Madison River Canyon, about 14 miles by road from Norris, Mont. Built in 1907 by Madison River Power Co.DAM: Rock filled wooden crib structure, 183 ft. long, 34 ft. high or 44 ft. to top of flashboards.SPILLWAY: 140 ft. long, equipped with flashboards 10 ft. high.PIPE: One 10-foot and one 12-foot wood-stave pipe, 7,515 feet long.PRESSURE: One pressure chamber, 32 ft. high, 30 ft. wide and 81 ft.CHAMBER: long, built of concrete.PENSTOCKS: 4 9-foot steel penstocks about 200 ft. long, one for each wheel.WATER WHEELS: 4 double horizontal, center discharge, Sampson special 44-inch turbines, 3,600 h-p., at 100 ft. head. Speed 300 r. p. m„ direct connected to generators.GENERATORS: 4 G. E., W. C., 2,250 k-w., 4,000 volts, 300 r. p. m., 3 phase, 60 cycles, alternators, with exciters mounted on same shaft.TRANSFORMERS: 12 G. E., W. C., 900 k-w., 60 cycles. High tension voltage 23,100, 34,650, 46,200; low tension voltage 4,000, 3,800, 3,600. Now operating at 46,200, delta connected. They can be connected Y for 40,000, 60,000 or 80,000.OPERATION: This is the principal plant of the whole system and carries most of the load."

Jan 1, 1913

By Georgios Kafantaris, Carsten Bonde, Nataša Katic

Within the investigation works for the Copenhagen Cityring metro, Geo/CMT have carried out 90 geotechnical boreholes. Together with the previously available investigation, this resulted in more than 15 km of vertical drillings and several thousands of laboratory tests. The design is made for 17 stations, four shafts and two parallel 16 km long tunnels. The geotechnical investigation and design have been carried out in several stages comprising appropriate refinement of structural design and design of excavation operations, including TBM break-in and launching operations at each station shaft. Acceptance of the solution and / or refinement of the investigation and design schedule in the next stage were based on the geological conditions, area availability at surface level, planning and cost-control criteria. The applied recursive design refinement is presented herein with an example of the Østersøgade shaft location.

Jan 1, 2016

By Zhang Yaonian

This paper describes full-scale tests on ten large bored piles with grouted end conducted for three projects in the urban area of Fuzhou city. Test program included site investigation, pile installation and end grouting. The piles were instrumented with strain gages and load cells to determine load distribution in the piles. Test results showed that end grouting improves load-settlement performance of bored pile. End grouting significantly increases the shaft resistance near the pile end. The better the end condition, the greater the shaft resistance. The average shaft resistance of the bored piles with grouted end is much higher than that of piles without grouting.

Jan 1, 2004

By E. D. Gardner

This is one of a series of papers describing mining and related subjects affecting mining in western mining districts and mineralized areas. The parts of this paper pertaining to current production, mining and milling methods and practices, and general conditions affecting mining were collected principally during a field survey made in May 1935. Some original data obtained on previous visits to the area are also included. The history, geological background, and past production of the mines and district are largely abstracted from previous publications, for which due credit is given later in the test. The principal districts in the Black Mountains are the Oatman or San Francisco and the Union Pass or Katherine. This range contains the principal producing mines of the State, in which gold is the only important metal. Although the total production of gold is relatively small as compared to other districts where the precious metals are obtained as a by-product in copper min¬ing, the area is one of considerable economic importance to the State.

Jan 1, 1936

By J. R. Thoenen

In Progress Report 1,4/ a number of facto mere demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

By I. E. Teymenson, L. A. Bakhvalov

Irrational usage of mineral commodities leads to depletion of natural resources and various ecological violations in natural environment. Fulfilment of a number of measures and strategic decisions by given problems requires a correct forecast of trends of social-economic systems. For solving the task of long-term forecasting special procedures, considering Kondratyev’s big cycles of world conjuncture, have been embedded into algorithms of unknown parameters identification and recovering of factors of different countries mineral resources production and consumption models. In the paper the classification of long cycles types, existing forecasting algorithms on the basis of Kondratyev’s ‘long waves’ or ‘K-waves’ and the modified algorithm, developed by us, which allows to reduce time and financial expenses and to improve the forecast quality, are presented. Furthermore, the article includes several forecasts of mining branch corrected models factors, received by us, permitting complex prognosis of economic and social development of different scale and control level systems. In the paper workability of proposed forecasting algorithms on the base of ‘K-waves’ and adequacy of created models to researched processes are proved.

Jan 1, 2003

By Keith L. Harris

Surprisingly, real gross national product (GNP) surged at a seasonally adjusted annual rate of 4.3% for the first quarter of 1987 according to preliminary estimates made by the Department of Commerce, the highest rate in 3 yr and significantly above the revised fourth quarter 1986 rate of 1.1% (table 1). The spurt, however, was caused by an unusual $59.5 billion rise in inventories, mostly cars and trucks, and there was little support from other sectors of the economy. Motor vehicle inventories rose as consumers continued to tighten their purse strings--consumer spending declined 0.4% for the second quarter in a row. Nonresidential and residential fixed investment and government purchases of goods and services were also down from the previous quarter. The increasing cost of energy was the major factor in the jump to 3.696 in the rate of inflation, as measured by the fixed-weighted price index for GNP, and rising inflation also helped put a damper on consumer spending. The underlying good news was that the trade deficit shrank for the second quarter in a row as imports declined at an annual rate of 11.1%. Also, profits in the manufacturing sector rose strongly in the fourth quarter, and for the first time in 9 quarters, the primary metal industries became profitable (table 1). If one discounts the anomalous inventory growth, the bottom line is that the economy continues to grow at close to the expected 2.5% level experienced over the past 2 yr. Of concern over the next several quarters, though, is the impact of the large over- hang of motor vehicles inventories on the economy. EMPLOYMENT The civilian unemployment rate declined to 6.636 in March after remaining at 6.7% for the previous 3 months. Employment continued to expand in February and March, although growth was significantly slower in March than in previous months. The manufacturing sector, however, lost 24,000 jobs in March after gaining 46,000 in February. Three-quarters of that gain came when striking workers at USX Corp. and Deere & CO. returned to their jobs. Employment in the manufacturing sectors of direct interest to the mineral industries has generally been increasing for at least the last quarter, while worker hours for these sectors have been on the upswing since April 1986 (figures 1 and 2).

Jan 1, 1987

By Keith L. Harris

Economic activity in the United States picked up in the third quarter, according to the latest estimate released by the Department of Commerce. Real gross national product (GNP)--the Nation's output of goods and services--grew at a seasonally adjusted annual rate of 4.3%, or $17.6 billion, compared with a rate of 1.9% for the second quarter of 1985 and 1.6% for the third quarter of 1984 (table 1). The 4.3% rate is one percentage point above the preliminary estimate reported in the August/September issue of Minerals and Materials. Most of the upward revision was due to the change in business inventories and Government purchases, while the figure for net exports was revised downward substantially. The 4.3% growth bettered by 1.5% the average rate of growth in GNP from 1974 through 1984 and was 1.1 % above that of the period from 1975 through 1984 and 0.7% above that of 1980 through 1984. Of importance to the minerals industry was the $14.4-billion growth in personal consumption expenditures, $10.2 billion of which was for durable goods (especially domestically produced automobiles) and the growing residential investment. The net export deficit continued to grow, however, and investment in nonresidential structures, producers' durable equipment, and business inventories declined. Prices, as measured by the GNP fixed-weighted price index, increased at an annual rate of 3.1% in the third quarter, compared with 3.9% in the second quarter. The slower rate of inflation resulted mainly from a decline in energy prices, following second-quarter increases. Fourth-Quarter Prognosis Many of the economic data available for October and November indicate that the economy is growing modestly and will continue to grow over the next 3 to 6 months. The composite index of leading indicators, designed to predict economic activity within 3 to 6 months, rose 0.3% in October, the sixth consecutive monthly advance, according to the Department of Commerce. Six of the 11 available leading indicators were positive: Stock market prices rose, as did sensitive material prices, credit outstanding, and manufacturers' new orders for consumer goods and materials; initial claims for unemployment insurance decreased, and firms were getting slower delivery of goods. Four of the indicators were negative: Business formations, homebuilding permits, contracts and orders for plant and equipment, and money supply all declined. The average hours worked per week, already at a high level, remained unchanged.

Jan 1, 1985

By Paul M. Tyler

The technology of clay and the manufacture of ceramic products therefrom, and also the clay resources of most of the individual States, are already covered by a voluminous literature. The present resume touches these matters only briefly; its purpose is essentially to bring together in small compass certain of the elementary factors affecting the potential commercial value of a clay deposit. In its preparation the author made extensive use of the annual chapters on Clay in Mineral Resources of the United States and in the two annual issues of the Minerals. Yearbook that succeeded them. For careful review and constructive criticism of the manuscript, the author is indebted to Hewitt Wilson. GENERAL DESCRIPTION The term ?clay? includes a great variety of substances that may differ widely in chemical mineralogical and physical properties. No two clays are exactly alike. All of them however, have the prominent characteristic of becoming more or less plastic when wet. Nearly all of the useful clays can be molded into articles, will hold their shape while being dried, and can be converted into a hard, rocklike substance by heat. Clay may, and in fact usually does, consist of a number of minerals among the commonest of which are kaolinite, quartz, feldspar, iron oxides, mica, bauxite, calcite, and manganese oxides. Organic matter is often present. Pure kaolinite, which has the formula A1203. 2 SiO2. 2H2O, is ordinarily, considered to be the parent "clay substance," butt most clays contain other hydrated mixtures of alumina and silica (aluminosilicic acids) along with indefinite amounts of sand and other nonessential minerals3/ Even, this so-called inert matter affects the plasticity, drying shrinkage, ease of drying, and final density, and at high temperatures may react chemically with the clay substance.

Jan 1, 1929

By S. S. PRENZ

Discussion held at the sessions of the Canal Zone meeting, November, 1910. [SECRETARY'S NOTE.-As a result of this discussion, an expression of opinion covering all points of unanimous agreement was adopted and signed by members of the Institute party as individuals. This statement, which was printed in the Bulletin of December, 1910, is reprinted below, as an introduction to ,the detailed report of the discussion. It should be clearly understood that it does not constitute an official declaration by the Institute, the rules of which forbid any such action. At the New Haven meeting of February, 1909, a free discussion of the plan of the canal took place, in which the critics of the present scheme had full opportunity to state their views. That discussion was continued at considerable length in the newspapers ; but the Institute was never committed to either side. In this latter instance, the situation is precisely similar. Certain members and guests of the Institute, having had the advantage of later developments and of personal inspection, have expressed the conclusions at which they have arrived on their own responsibility ; and these conclusions are published by the Institute, subject to further discussion, like any other part of its proceedings. The general statement referred to contained a promise that the full discussion, of which it was a result, would be subsequently printed ; and this promise is fulfilled, so far as practicable, in the subjoined report, concerning which I beg to offer the following explanations: 1. It is made up of the remarks of the members of our party, as subsequently written out and mailed to the Secretary. 2. In editing these contributions, I have condensed the material considerably by cutting out much repetition of opinions and phrases ; and in such excision, I, frankly confess, the authors whose communications were delayed, have been the sufferers. Nevertheless, there is a good deal of repetition left, as there must be, when so many persons had talked so much, and come to agreement upon so many points. 3. It has been found impossible to preserve in this report the actual order of the free and informal oral discussion represented. Consequently the several contributions have been arranged in alphabetical order under the names of their authors. References to "preceding speakers," etc., must therefore be construed as referring to other speakers, preceding or following.-R. W. R.] S. S. PRINZ AUGUST WILHELM, AT SEA, November 14, 1910. We, the undersigned, members and guests of the American Institute of Mining Engineers, after a visit to the Isthmus of Panama, and inspection of the work of the United States Isthmian Canal Commission, and after full discussion of our individual impressions, find ourselves in unanimous agreement as to the following conclusions:

Jan 1, 1911

MARCH 15-Industry is rapidly snapping back from another coal crisis, other business news is in general favorable and the outlook through the Spring is by most observers considered quite promising. Most industries report comfortable backlogs of unfilled orders, department store sales in recent weeks have equalled in dollars those of the corresponding period last year, retail sales of automobiles show again over the same period a year ago, and new orders for machine tools are at the highest figures since August 1946. Orders for railway freight cars have shown a very encouraging pickup, with a total of 9385 cars in January and the N. Y. Central alone ordering 4500 in February. Construction continues very active. In January new housing starts totaled 80,000 against 50,000 a year ago and the daily average contract awards, according to the Dodge reports, were 57 pct larger. In the first 22 days of February the increase in awards was 27 pct. Lumber orders since Jan. 1 have run 22 pct above last year. All of these favorable factors bolster the opinion that the upturn in industrial output and employment which began last summer has not yet spent itself and that the setback caused by the strikes will be made up when people get back to work. Only in a few lines are there indications that primary production may be outrunning the consumption of finished goods, although inventory build-up would seem to be rather modest as the National Association of Purchasing Agents reported in February that 78 pct of its members were buying for 60 days or less. Industrial prices as a whole show no significant trend despite the continued alarm over both the immediate and the long-term possibility of inflation caused primarily by the government's increasing expenditure and its inability to balance the budget. A recent advance of 1.9 pct in primary market prices is viewed by some people as the surface symptom of renewed inflation, but even so it is more than two years since the alltime high was reached by the daily index of sensitive commodities in November 1947. Over two years have passed since prices received by farmers hit their peak and about a year and a half since all wholesale prices and the consumer price index touched their highest points in August 1948. The decline in the wholesale price index has been almost continuous, interrupted only twice by slight advances in the monthly figures from February to March 1949, and, later in the year, from August to September. Of course, this continued decline in the last half of 1949 largely reflects a downward movement in farm and food prices. Wholesale prices for commodities other than farm and food leveled out after June and now stand only slightly under the June level. Farm products are down by 22 pct from January and by 18.6 pct from August 1948. Food prices are down only slightly less. Consequently, the farm price support program is in serious trouble and has imposed a heavy financial burden on the Treasury. In those commodities other than farm products only building materials, chemicals and textiles have come down as much as the average, while housefurnishings and metals and their products have fallen hardly at all. Glancing away from the domestic front, the results of the British general election indicated a highly inconvenient situation, that public opinion there is so exactly deadlocked as to divest the victors of much ability to make forceful decisions or create significant policy. It is generally considered that another election in the near future would give substantially the same result. The British people are equally divided and the politicians are not likely to precipitate another appeal to the country until there is manifest reason to believe that external and internal circumstances have changed sufficiently to permit one party or the other to obtain a decisive verdict. Because of the lack of a clear mandate steel nationalization will likely lag in Britain. In the meantime there is considerable discussion going on as to whether the European steel industries as a whole are at a disadvantage in world competition with the American industry. An article in the "Statistical Bulletin" for January of the British Iron and Steel Federation takes issue on this point with the authors of the Geneva report, observing that they wrote before devaluation, and this particular conclusion "has been overtaken by events." The "Bulletin" also contends that the statement was in any case incorrect so far as Britain was concerned, and that it was based on scanty and insufficient evidence. To support the rebuttal a detailed and extensive comparison is made of the home prices of certain steel products in Britain and in other countries of the world. The accompanying table gives a selection of the prices published. It sets out the changed position since devaluation and since the recent increases in American steel prices. These are home market prices; no doubt in competitive export business some of the price levels could be brought closer together at need.

Jan 4, 1950

By R. F. Miller, R. F. Campbell

Sixteen steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- atures. Diagrams summarizing the structnres and hadness resulting from these two cooling rates are presented (Figs. 3, 4, 7).t Data were also obtained on the influence of these two elements, individually and in combination, on the depth of decarburiza-tion observed after furnace cooling (Fig. 8). Composition of Material The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 2 5-ton Heroult electric-are furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- tric induction furnace. The cast ingots were hot-rolled to 1.75-in. bars. Air-cooled Series The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to 1830°F. (I000°C.) for 20 min. and oil-quenching. They were then reheated to 1740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1942

By J. A. M. Cano

Introduction Since the beginning of operations at the pellet plant at Ponta Ubu ES, Samarco Mineração SA has produced pellets for direct reduction and blast furnace processes. Of the total amount of pellets produced from 1977 through 1993, 55 % are used in the blast furnace, about 45 Mt (49.6 million st). The principal components of pellet gangue are calcium oxide, magnesium oxide, silica and alumina. They should be added in adequate quantities to guarantee the mechanical resistance of the fired pellets under blast furnace conditions. Over the years, the pellets produced by Samarco had a silica content between 2.5% and 2.8% and varying binary basicity preferably between 0.8 and 0.85. On the other hand, the increasing amount of industrial waste in siderurgical plants caused by the increase of steel production has caused some countries to put into practice methods to reduce the volume of slag produced in the blast furnace. This paper's goal is to find an alternative for decreasing the amount of slag produced in the blast furnace. It is possible to decrease pellet gangue by decreasing the silica content to about 2%, leaving the metallurgical properties and quality of pellets unaltered. For this work, Samarco pellets were used with Si02 between 2.5% and 2.8%, pellets with high silica and pellets with Si02 between 2.0% and 2.3% low silica. Both were partially fluxed by the range of varying basicity CaO/SiO2 from 0.8 to 0.95 during production. Experimental tests on pilot scale Thhis work began in January 1986 in the pilot plant (pot grate, Fig. 1) at Samarco. Its goal was to obtain preliminary data that would indicate the bybility of the project. It also formed a solid base to extend the studies in tests on an industrial scale of production for blast-furnace pellets. The pot grate is a test furnace composed of a gas burner, a combustion chamber and a grate, connected by hot air ducts. The burner is fed by a mixture of LPG and air. It reaches high temperatures through oxygen injection. The combustion chamber heats the air that comes from the turbocompressor. This hot air flows through the ducts to the grate on which the pellet samples are fired. During updraft drying, downdraft drying, preheating, firing and afterfiring, the upward and downward direction of the air flow can be controlled by valves driven by pneumatic cylinders. The pot grate indurator was fully automated in August 1989. Positive and negative pressures measurements resulting from gas passing through the pellet layer, as well as temperature readings, are recorded in graphs in relation to time for all tests. The tests depend on the various steps carried out in sequence that can influence the results of the tests. Therefore, some criteria were adopted to restrict the number of variables in the process. This was done to facilitate the results of the analysis. The pellets were composed of concentrate, bentonite, hydrated calcitic lime and metallurgical coal, all regularly used in the pellet plant. The material balance of the pellets mix was determined from the chemical analysis of the components. Table 1 shows the chemical characteristics of the concentrate and the additives used in the pilot plant and industrial tests. The basicity has a marked influence on the metallurgical properties of the pellets produced by Samarco with a silica content between 2.5% and 2.8%. However, for pellets with low silica (about 2%), it was necessary to study the variation in the parameters of quality in a wide range of basicities to deliniate with precision a scope of work. A large variety of low-silica blast-furnace pellets were produced at the pilot plant with binary basicity varying between 0.8 and 0.95. After chemical analysis, those pellets were separated into five groups of different binary basicity (0.8, 0.84, 0.87, 0.90 and 0.95). Each was then split, one part for metallurgical tests in the laboratory at Samarco and another to be evaluated in a laboratory for metallurgical tests in Germany. It was agreed that the tests to evaluate the quality of the pellets in the two [ ]

Jan 1, 1996

By R. F. Campbell, R. F. Miller

Sixteen steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- atures. Diagrams summarizing the structnres and hadness resulting from these two cooling rates are presented (Figs. 3, 4, 7).t Data were also obtained on the influence of these two elements, individually and in combination, on the depth of decarburiza-tion observed after furnace cooling (Fig. 8). Composition of Material The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 2 5-ton Heroult electric-are furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- tric induction furnace. The cast ingots were hot-rolled to 1.75-in. bars. Air-cooled Series The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to 1830°F. (I000°C.) for 20 min. and oil-quenching. They were then reheated to 1740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1942

By Aylmore M. G

Samples have been taken from a two-stage industrial gold roaster treating a pyrite/pyrthotite/arsenopyrite concentrate, in order to describe the mineral- ogy, composition and surface area of the calcines. Sulfides oxidised to produce a porous magnetite in the first stage and a porous hematite in the second, pyrite predominantly roasted via a pyrrhotite intermediate. Sulfur was eliminated in both the first and second stages whereas arsenic was eliminated in the first but retained in the second, partly as rims on hematite particles. The finer sized particles from the cyclones and electrostatic precipitator, whilst having the greatest surface area, were the most refractory with respect to gold solubilization, probably as a result of incomplete decomposition (through short-circuiting) in the first stage, and through a combination of factors such as overheating and entrapment of sub-micro- scopic gold in the second stage.

Jan 1, 1991

By B. V. Driga

The paper presents the evaluation method of the thermal power potential of the salt lakes developed in collapsed salt mines in Romania. It is well-known that the hydro-chemical stratification of these lakes favors warmer internal layers. The degree of heat varies during the year, but, taking into account the large number of genetic lakes of this type, it can be used as a local utilizable power source. The authors analyze the correlations between the physico-chemical parameters of the water and the degree of heat stored as a function of the morphological parameters of the lakes, as well as the technical parameters for capitalizing on this power.

Jan 1, 2008

By James S. Graham

Marine design and construction methods are presented on the caisson foundations for the tower piers at the Brooklyn, Ben Franklin, Delaware Memorial 1st, Tappan Zee, Walt Whitman, Throgs Neck, Verrazano Narrows, Delaware Memorial 2nd, and Newport Bridges. All of the bridges are founded on caissons, bearing on bedrock, soil, or piling. Caissons at the Tappan Zee Bridge are partially supported by piling and partially by buoyant forces. General subsurface conditions for each are provided. The purpose of this paper is inform engineers how bridge foundations using caissons were built over major waterways in the Northeastern USA in the past, anticipating a surge of new bridge construction in the near future.

Jan 1, 2013

By Yi Luo

Bolting the mine roof is one of the noisiest underground mining operations. The main contribution to the high noise is the drilling of the roof bolt holes, especially in hard rock. A previous research shows that the specific energy consumed in drilling the bolt holes is inversely proportional to the bite depth (i.e., penetration per drill revolution). Less specific energy at a reasonably high bite depth means less energy is wasted in the drilling process to produce heat, bit wear and noise. Therefore, control of drilling operation to achieve a higher bite depth can provide an opportunity to reduce drilling noise from its sources as a proactive noise control approach. In order to explore the feasibility and to develop the proactive technology for reducing drilling noise, drilling tests have been conducted in laboratory settings. The preliminary results show significant reduction in noise dose can be achieved by drilling in medium hard rock at a reasonably high bite depth. This paper presents the findings from the laboratory experimental studies conducted so far.

Jan 1, 2013

Robertson Diasol have developed a spectral gamma-gamma tool fully able to withstand borehole conditions. Spectral data is digitally recorded across 256 channels depending on energy levels of the photoelectric effect. Data processing is being developed with the objective of calibrating channel amplitudes to mineral type which will lead to a direct log of selected mineral grade as a continuous trace with depth.

Jan 1, 1990

By D. B. Dow

This report on methods employed for dehydrating oil-field emulsions, is the second of a series prepared as a result of a study of oil-field emulsions recently completed by the writer. The first paper2 dealt with the factors responsible for the formation of emulsions. A third paper will discuss the physical chemistry involved in the formation and resolution of such emulsions. In the early development of the oil fields of Pennsylvania, no emulsion troubles of any consequence were encountered, nor to any serious extent in the oil fields of other Eastern States: However, with the development of fields west of the Mississippi in Oklahoma, Kansas, Texas and California, where heavier oils of different characteristics were found, the problem of dealing with cut oil soon became of great importance.

Jan 1, 1925