Search Documents

By Walter W. Kaufman

This report summarizes a study conducted to establish the nature and impact of regulations governing disposal of refuse from underground coal mines. The regulations affecting refuse disposal in eight major coal producing states are collected, summarized and reviewed. Federal regulations applicable to refuse generated by underground coal mines are also included. Common refuse disposal practices are discussed as are the refuse quantities generated annually in each study state. Technical requirements of regulations are discussed acid presented in appended tables. Economic implications are also assessed through cost analyses of three major types of disposal processes. The report also includes an assessment of future trends in regulation and refuse generation plus a series of recommendations concerning potential improvements in both the regulatory and refuse disposal processes.

Jan 1, 1978

By Roy C. Bartholomae

This Bureau of Mines report presents the results of a laboratory investigation of coal cutting mechanics and noise. These experiments were performed using linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts was ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to formulate analytical models of the coal cutting forces and noise. The analytical model for coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as provide benefits to other important areas of health and safety in underground mining.

Jan 1, 1983

By Edwin E. Maust

In response to the ever- increasing demand for high temperature materials, the Bureau of Mines instituted a program for the study and development of superrefractories, One of the major tools obtained for use in this research was an image furnace of the double-paraboloidal mirror type. Although extensive theoretical analyses of solar furnace performance may be found in the literature, comparable detailed information on the double-paraboloidal-mirror image furnace has been nonexistent. This report presents an analysis based on an investigation undertaken to ascertain the limitations and characteristics of the furnace so that it can be used most effectively. The quantitative determination of the energy available at the image, the control of this energy by mans of a 60-inch iris diaphragm, and its variation with position and time relative to the heat source used have all been dealt with in detail. The quantitative results were obtained using a specially designed waterflow calorimeter and these measurements, in conjunction with the theoretical analysis, are used to present a fairly complete description of the furnace and its capabilities.

Jan 1, 1962

By M. D. Balen

The U. S. Bureau of Mines has undertaken the development of mineral industry cost escalation factors to enable the estimation of mineral development and extraction costs for mineralized sites in Alaska throught the use of the Bureau's Cost Estimating System v2.0 (CES 2.0). For the purposes of this document, all calculations are based on, and reflect the economic environment in Alaska in July 1992. The greater cost of mining in Alaska as compared to the contiguous-48 States can be estimated for Alaskan mining operations through (1 ) the analysis of capital and operating costs for analogous mine and mill plants in operation in the contiguous-48 States; (2) the hypothetical relocation of mine and mill plants from their actual location(s) to Alaska by making engineering modifications to the mine and mill plant design as required by the Alaskan site characteristics; (3) calculation of the cost of the required engineering modifications and; (4) the escalation of all costs to a level representative of the economic environment in Alaska at some specific point in time.

Jan 1, 2011

By I. Liebman

The Bureau of Mines conducted experiments on coal dust explosion suppression. The investigation took place on a beltway in the double-entry of the Bureau's Experimental Mine. Using conditions that simulate those in a working mine, the investigation showed that a coal dust explosion can be readily initiated in a conveyor belt entry. Also, the explosion can spread into adjacent entries through opened crosscuts (stopping destroyed by explosion) to propagate for long distances even though the adjacent entries are rock dusted in compliance with regulations. Passive water barriers (water-filled tubs) were found to be effective in suppressing explosions on a beltway; however, barrier efficiency was reduced by opened crosscuts. The study indicated that the beltway barrier should be the distributed type consisting of continuous rows of water-filled tubs covering long distances along the entry. A plan is outlined for the installation of a water barrier system in a working coal mine for the protection of a beltway.

Jan 1, 1981

By D. H. Desy

The Bureau of Mines has conducted research on the ignition of methane-air mixtures by sparks caused by frictional impact of aluminum alloys on rusted steel at typical coal mine fan speeds. The objectives were to establish the incendivity of aluminum alloys under these conditions, to investigate differences between aluminum alloys, and to evaluate substitute materials for the aluminum-steel combination. With a specially designed apparatus, three commercial aluminum casting alloys and a number of experimental aluminum alloys were tested for incendivity of the frictional impact against rusted steel in flammable methane-air mixtures. All aluminum alloys tested produced some ignitions. Of the experimental alloys, the harder alloys and those containing silicon tended to be more incendive than the others. With the normal experimental conditions, constructional steel, stainless steel, brass, and plastic did not cause ignition of methane-air mixtures in frictional impact against rusted steel. Some ignitions occurred with constructional steel at high speed in more flammable gas mixtures enriched with oxygen. From these findings, it is suggested that constructional material combinations other than the aluminum-steel combustion would minimize this inc endive hazard. A detailed description is given of previous research, and comparison is made with present results where appropriate.

Jan 1, 1975

By James H. McCutchan

The small and remote mine operators must comply with the Federal Mine Safety and Health Administration regulation requiring them to train and maintain mine rescue teams. The alternative is for the operators to contract with established teams within two hours travel time of their mine. Many of these remote operations are too far away from established teams and have too few employees to make up the necessary teams. Many cannot comply with the regulation either from a manpower or economic standpoint. The Office of Arizona State Mine Inspector, under the direction of the Honorable James H. McCutchan, State Mine Inspector, entered into a contract with the Bureau of Mines to develop the concept of a volunteer mine rescue program. This program with the assistance of the mining industry and volunteer rescue organizations, has planned and instituted a statewide volunteer mine rescue organization. The trained and equipped volunteers are stationed throughout the state and can respond to a mine emergency within the time constraints.

Jan 1, 1984

By Normal Seidle

This report (rind related Appendices) provides a description of the functional design specifications and related rationale for development of a training system for dragline equipment operators. Phase I activities involved a delineation and detailed analysis of specific behavioral requirements for successful dragline operation. Following the field data collection effort, job/activity/task descriptions were formulated into training requirements which can be achieved by a trainee with training hardware having specific functional capabilities. The training system analysis integrated the training requirements and the trainer functional capabilities into recommendations which configure a total training system. The objective of the training system described in this report is to provide new operators of dragline equipment with the requisite skills and knowledge to assure cost-effective development and an adequate supply of our human resources.

Jan 1, 1975

By Sam S. Taylor

The disposal of oil-field brines by injection into subsurface formations other than fresh-water-bearing strata is a positive method of eliminating the harmful effects of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. The methods used most generally for the disposal of brines produced with oil are (1) impounding in evaporation ponds, (2) controlled diversion into surface streams, and (3) injection into subsurface formations. Various States recognize one or more of the methods as legally authorized procedure. As a general rule, impounding brine in ponds and solar evaporation have not been entirely successful, principally because of the large volumes handled; the porous nature of the soil, and the low rate of evaporation. Likewise, the diversion of brine into freshwater streams by controlled dilution has not proved satisfactory in some areas, especially in parts of Kansas and Oklahoma where the rainfall is relatively low, because it has been impossible to obtain enough fresh water for such dilution.

Jan 1, 1939

By Kim B. Shedd

An initial evaluation of the flow of cobalt-containing materials in the United States was prepared. The following aspects of materials flow were included: cobalt released as a result of mining and processing other metals and minerals; scrap generation and subsequent recycling or cobalt recovery; and cobalt losses resulting from the generation of wastes, dissipative uses, and disposal of used products. Where possible, estimates were made to quantify the amount of cobalt lost from the materials flow. More than 2,000 metric tons (mt) of cobalt are released annually from mining and mineral processing in the United States, including 480 mt of cobalt in coal produced in the United States. Metallurgical industries examined in this study have well-established recycling or cobalt recovery practices. The petroleum industry recycles spent catalysts, and some chemical catalysts are also recycled. Losses generated during cobalt chemical and powder processing were estimated at 50 to 80 mt of cobalt annually. Losses from alloy processing and the manufacture of parts and products were estimated to be 360 mt. These industrial losses are greatly outweighed by an estimated 2,780 mt of cobalt' consumed in the United States each year to make products that will ultimately be disposed of.

Jan 1, 1992

By G. A. Wancheck

Shear tests were performed on several prepared samples of granular and powdery bulk materials to investigate the following parameters: Particle size and distribution, particle movement, moisture content, consolidation of material, bulk density, void ratio, porosity, volume change, and strain rate. A series of shear tests was performed with weight-percent-ratios of minus 0.185-inch tertiary sand and 1-1/2-by l/2-inch tertiary gravel mixtures, and weight-percent-ratios of minus 200-mesh limestone (rock dust) and minus 200-mesh bituminous float coal dust. A comparison was made for shear test results obtained with rectangular and circular shear cells utilizing the large and small direct shear testers. Specifically, the shear results obtained include the angle of internal friction or shear strength of the tested material under known consolidating pressures, and the kinematic angle of friction or coefficient of friction between the interface of a bulk material and a sample wall material. The experimental procedure, tests, and results are given for each parameter investigated.

Jan 1, 1973

By D. K. Caddel

Several problems exist with the present design of coveralls used by miners in low coal (seam height 48 inches or less). The back portion of the coveralls often tears when roof bolts or rough areas in the roof are hit. Movement in the shoulder area is restricted. Female low coal miners find it difficult to purchase coveralls that fit properly, and must remove both their hard hat and safety belt in order to urinate and defecate. The objective of this research was to design coveralls which would alleviate these problems. The following features were incorporated into the coveralls; padding in the upper back area to avoid tearing, an action pleat in the shoulders to increase mobility, an inseam zipper to more easily allow miners to perform their bodily functions, and reflective tape to increase visibi¬lity of the miner. A heavyweight denim fabric was used to increase warmth and durability of the coveralls. The coveralls were assessed K long four parameters (comfort, safety, worker productivity, and fabric suitability) using both an in-field assessment by low coal miners and simulation studies. The experimental coveralls proved superior to conventional coveralls along all four parameters. Work clothing sizes for female miners were developed.

Jan 1, 1982

By Sidney Katell

Philippine laterite and serpentine ores can be utilized in an electric furnace operation to produce both a steel ingot and a ferronickel product. Figure 1 is a schematic interpretation of a plant in which laterite and serpentine ores are processed separately to obtain both ferronickel and steel as products. A relationship of estimated capital requirements and probable returns has been established in this study for a plant of this type. No attempt has been made to evaluate the risks involved in commercial operations. At such time that the project might be constructed and placed in operation, changes in the costs of material, labor, and power may materially affect the profitability aspects of this study. One of the uncertainties involved in the economic evaluation is the cost of mining, handling, and shipping the ores. It is on this basis that the cost of ore delivered at the plant is assumed to be variable at $3, $5, and $7 per net ton (dry basis). For all other costs a plant site at Iligan City, Philip-pine Islands, has been assumed in preparing the economic characteristics for a plant that will process 2,000 tons4/ of ore per day. Results of the study, for the 2,000-ton plant, with all monetary values expressed in terms of United States currency (Philippine peso valued at $0.50), are summarized as follows:

Jan 1, 1962

By Thomas O. Meyer

Laboratory test results are presented for the determination of elastic modulus made with the NX borehole jack. Determinations were made in massive pieces of aluminum so as to satisfy conditions of linear elasticity, homogeneity, and isotropy. Results indicate a large discrepancy (approximately 200 percent) betwen material modulus as determined by laboratory block-loading tests and that indicated by the jack under relatively ideal circumstances. Effects due to interface friction, finite block size, incomplete plate-bore contact, and other factors were examined and found not to be significant. Finite element results indicate that assumed loading conditions for the jack differ from those actually occurring, at least in materials of high elastic modulus (approximately 10 million psi), such as quartzite.

Jan 1, 1974

By William M. Hinton

This report describes the approach, procedures, and results of a program to develop training materials for roof bolter operators. The objective of the program was to design and produce a training sequence which would prepare roof bolter trainees for job performance. Data was collected and analyzed using the general procedures of Instructional Systems Development (ISD). Input data came from a previous roof bolter training analysis program. This data was expanded and structured through a series of ISD steps: objectives hierarchies, media selection, syllabus, lesson specifications, and train¬ing materials development. The resulting program consisted of an ordered sequence of 15 lessons. The media mix for the 15 lessons included lectures, slide-tape lessons, and hands-on instruction using operational roof bolters. Contents of all lessons were reviewed and approved by the Bureau. The key recommendations were to (1) validate the materials and measure relative effectiveness of media formats; (2) survey mines for training resources and conditions - match materials to user capabilities, rather than selection state of the art technology/media; (3) develop job performance aids (JPAs) rather than simulators; (4) create a style/media/JPA development guide for use in future projects of this kind.

Jan 1, 1982

By L. A. Stewart

This paper describes all occurrences of barite in Arizona that were known or reported to the authors. The history, ownership, production, and geologic setting are discussed for most of the deposits. The uses and specifications of product grades are briefly discussed. Seventy-five deposits were examined in 9 of the 14 counties of the State. The descriptions are given under county headings. No occurrences were reported in the four northeastern counties of Coconino, Navajo, Apache, and Greenlee, nor in Santa Cruz in the southern part of the State. From about half of the deposits examined, 55 samples were taken; of these, 45 were for chemical analysis, and 8 larger samples, ranging from 100 to 350 pounds, for beneficiation tests. A 30-ton bulk sample was taken for pilot-plant tests. Bench-scale flotation tests of the eight samples employing several different procedures and reagent combinations yielded marketable-grade barite products with barite recoveries ranging from 60 to 97 percent. Five of the samples contained enough fluorspar to warrant its recovery. Acid-grade concentrates, which accounted for fluorspar recoveries of 45 to 70 percent, were obtained from three of these ores. Batch laboratory tests of a representative portion of the 30-ton bulk sample revealed that acid-grade fluorspar and high-grade barite concentrates could be recovered. Results of the laboratory and continuous pilot-plant tests of this ore will be presented in a separate report.

Jan 1, 1960

By E. E. Ungar

Criteria applicable to noise in coal cleaning plants are presented, and the generally applicable noise control principles and approaches are discussed. The operating characteristics and equipment of coal cleaning plants are described. Considerations entering in the selection and design of noise control means are delineated, and specific means for equipment noise reduction are described. The limited utility of acoustically absorptive materials in plant spaces is indicated, administrative means for reducing worker noise exposure are pointed out, and ear-protective devices are described briefly. The reduction of plant noise reaching nearby communities is discussed. Programs leading to quieter machines an coal cleaning plants are suggested.

Jan 1, 1974

By O. C. Blade

Studies on more efficient utilization of petroleum have been made for 50 years by the Bureau of Mines. As part of this work, the Bureau has analyzed thousands of samples of crude oil by its standardized routine method, and many of these analyses have been published, sometimes in special compilations, other times in connection with reports of research on petroleum. This report is a finding index for all analyses published from 1921 to 1959, and brings up to date the information in Information Circular 7470 3 and in the appendix of Bulletin 490.4 The routine method of analysis and the equipment originally were described in a report by Dean and associates. 5 This report has long been out of print, but Bulletin 490, bringing the procedure and its modifications to date, was published in 1951. 6 Briefly, the procedure consists of testing, by standard methods, small samples of a crude oil for gravity, sulfur, color, viscosity, pour point, and (more recently) nitrogen; and, by a standardized procedure, distilling a portion of the crude oil and determining certain properties on the separated fractions and residuum. Careful records are made during the procedure, and the distillation data obtained are used to compute the approximate amounts of products present in the sample--such as percentages of gasoline, kerosine, gas oil, and lubricants. The principal data and results are recorded on a standard analytical report form. An analysis of a sample of crude oil from a recently developed field is shown in table 1. Compilations of these analyses, sometimes in tabular form and usually for specific geographic areas, are published from time to time. Analyses often are included in connection with other studies, such as engineering field reports.

Jan 1, 1959

By Louis Schaffer

The objectives of the research were to determine whether a model health and safety program could be defined in terms which would enable its application to mines of all types, and, if such a model program could be defined, to determine through evaluations in two mining companies whether it would achieve measurable improvements. Volume 1 describes the model, how it was applied in the field and how it was evaluated. This, Volume 2, describes the literature and field research that preceded the model definition.

Jan 1, 1983

By Ronald W. Stingelin

The geology of the roof of the Pittsburgh coal bed was studied and mapped in nine contiguous counties containing the bulk of the remaining reserves of this coal bed in the northern Appalachian Coal Basin. Drill core records from Belmont and Monroe counties, Ohio, Washington and Greene counties Pennsylvania, and Ohio, Marshall, Wetzel, Monongalia, and Marion counties, West Virginia provided the data for twelve computer generated regional geologic variable maps. Four of these geologic variables (overburden thickness, vertical distance to the rider coal, lithology at the five foot horizon above the roof of the mineable Pittsburgh seam, and the number of lithologic changes within the 30 foot interval above the roof of the mineable Pittsburgh seam) were used to estimate the risk of potential roof falls by a methological scheme developed during this study. A hazard zone risk map was developed showing a generalized regional trend of increasing risk from west to east across the basin. Mapping of individual geologic variables and mapping of hazard risk can be done at any scale. The accuracy of the mapping is primarily dependent on the density of the drill core records. Geologic feature maps and the hazard risk map contained in this report are reduced (1 :500,000 scale) versions of the larger scale (1 :62,500) maps prepared for the Bureau of Mines as map folios.

Jan 1, 1979