Search Documents

By Arno C. Fieldner

Six years ago, I addressed the annual meeting of the American Society for Testing Materials on "Fuels of Today and Tomorrow."3/ Since then, our country has been drawn into another great war of veritably global extent, with unprecedented demands on fuels, foods, and materials in general. My purpose in this address is to review the changes in fuel supply and demand since 1937 and to give you my views on the outlook for the future. CONDITIONS IN. 1237 Daring 1936 the United States produced and consumed one-third of the world production of coal, two-thirds of the petroleum, and about 95 percent of the natural gas. Two-thirds of the oil produced in all countries since the discovery well was drilled in 1859 had come from American wells. With the exception of the three depression years 1931, 1932, and 1933, new oil reserves were being discovered since 1924 well in excess of our increasing rate of consumption. Discoveries of natural gas, likewise, were tremendous in volume, and this fuel was being transported to most parts of the country by pipe lines; some of them more than 1,000 miles long. We had all kinds of mineral fuels in abundance and at prices that did not stint anyone in the maximum utilization of the mechanical devices that were being developed on every hand. No one suspected that the time might come in a few years when, gasoline would be doled out to some of us at the rate of 1-1/2 gallons a week or that many of our fuel-oil furnaces would have to be converted to burn coal. Of course, these restrictions are due to unusual war conditions, such as lack of coastwise tanker transportation, unprecedented demand for aviation gasoline, and the shortage of rubber for automotive tires. However, these shortages do call our attention to the vital part of petroleum reserves in our country's future position among nations. Therefore, it is of special interest to review briefly the relations of recent supply and demand with respect to our various mineral fuels.

Jan 1, 1943

AustraliaÆs strong position as an aluminium producer and potential magnesium producer combined with rapid market growth in the automotive industry, proximity to Asia and other natural advantages points to considerable opportunity for downstream processing and manufacture with light metals in this country. Development of a vertically integrated light metals industry in Australia needs to be pursued with vigour, as does the continued development of global strategic alliances through the value adding chain.

Jan 1, 2000

By Shirley F. Colby

The past 40 years have seen the sand and gravel industry grow from small roadside pits and holes in farmers' back yards to giant corporations selling millions of tons of sand and gravel each year and owning plants representing huge capital investments in land and equipment. The days hen a man could "work out" his taxes by providing the materials for nearby roads are gone forever. In addition to the hundreds of privately owned and operated plants, Government agencies operate sand and gravel pits and plants to supply aggregates for the tremendous road-building and public-works programs in progress during the past few years. EXPANDING PRODUCTION In 1940 the send and gravel industry produced almost a quarter of a billion short tons valued at more than 110 million dollars. This compares with less than 2 million short tons worth 1 1/2 million dollars produced in 1902. The practice of screening sand and throwing away the gravel in the early days of the industry's growth has stopped, and in 1940 gravel constituted two-thirds of the total production. In 1906, the first year in which sand and gravel were reported separately gravel accounted for only one-

Jan 1, 1942

By W. A. Wright

The use and abuse of social media restate common employee relations issues. Business solutions to these issues require advanced preparation. Employers should establish and enforce social media policies to guide their reactions to employees? social media posts that reflect on the employer and its business.

Jan 1, 2011

By William H. Pomroy

This report describes research leading to the design, prototype fabrication, and successful in-mine proof-of-concept testing of two improved stench fire warning systems for underground noncoal mines. The stench system, widely used in underground noncoal mines to warn of fire or other emergency suffers several serious shortcomings, including the toxicity of the odorant leading to debility in miners; reactivity of the odorant with iron oxide, resulting in unreliable warning because the odor may fade when transported long distances in steel pipe; lack of control over the rate at which agent is released into the air-stream, resulting in some work areas receiving unbearably high stench concentrations and other areas being missed altogether; lack of visual indication of system status, valve positions, or proper system operation; and excessively long stench transit times. In 1979, the Bureau of Mines, U.S. Department of the Interior, began research to upgrade the stench warning system. Two systems were subsequently developed which offer significant advantages over current systems.

Jan 1, 1984

By J. B. Clemmer

Fluorspar is one of the most important nonmetallic minerals and is used extensively in the metallurgical, ceramic, cement, and chemical industries. The steel industry consumes most of it, but as the Mineral is the chief source of fluorine, it is becoming increasingly valuable to the chemical industry in the production of fluorine compounds The development of nontoxic organic fluorides for use as refrigerants in mechanical refrigeration and air-conditioning units illustrates the increasing use of fluorspar in the chemical industry. Most domestic flurospar comes from deposits in the Illinois-Kentucky district, which centers around Rosiclare, Ill. About a dozen companies operate in the district, which comprises parts of Pope and Hardin Counties in southern Illinois and Crittenden, Livingston, and Caldwell Counties in western Kentucky. According to the latest available statistics, this district supplied 1/5,960 short tons of fluorspar in 1937, compared with the total domestic production of 181,230 tons. Imports totaled 37,063 tons.

Jan 1, 1939

By J. Moyes

The Intec Process is a generic process for the production of pure base metals and precious metals from sulphides concentrates derived from copper, nickel, zinc and lead ores. The development program for the Intec Process initially focussed on the treatment of copper concentrates, (the ?Intec Copper Process?), and more recently of zinc concentrates, (?the Intec Zinc Process?). Developed and proven in Sydney, Australia at a cost of US$15m over the last ten years, the Intec Copper Process is now ready for commercial application. The knowledge gained during the development of the Intec Copper Process has been applied to the Intec Zinc Process, which utilises the same basic chemistry to produce high purity zinc ingot from metallurgically complex zinc sulphide concentrates containing lead, copper, iron, silver and gold. The demonstrated ability of the Intec Zinc Process to treat low grade mixed zinc/lead/copper concentrates, including those with high iron and manganese levels, holds out the real prospect of overcoming major metallurgical hurdles that have long affected the zinc industry. The Intec Zinc Process consists of the three consecutive circuits of leaching, purification and electrowinning. The leach circuit is of single stage configuration with a series of reactors to which concentrate and lixiviant are fed. Purification consists of cementation and precipitation by pH adjustment. Electrowinning employs an electrolytic cell very similar in design to that of the Intec Copper Process, but differs in that a conventional plate cathode is produced. During electrowinning, the same mixed halide species (BrCl2 -, HalexTM) that is integral to the Intec Copper Process is generated in solution at the anode and exhibits powerful leaching characteristics capable of directly leaching the sulphide concentrate feed. The need to roast the concentrate prior to leaching, as is practised in the conventional Roast/Leach/Electrowin (RLE) process, is thus eliminated whilst a range of by-products (notably lead, copper and precious metals) can be extracted in the simple, single-stage leach. This paper describes the Intec Zinc Process; the technology, predicted economics and its environmental aspects.

May 1, 2002

By R G. Richards

Although most New Zealand coals are low in ash, there are situations where high ash coals could be won. Not all high ash coals can be upgraded by physical means, since the ash is either inherent in the coal or bound in such a way to make its physical removal either impractical or uneconomic. Nevertheless, the authors believe, the situations where high amounts of ash can be economically removed by physical means to make a saleable product are considerable.

Jan 1, 1979

By Ralph H. Whaite

To assist the anthracite industry obtain technical data on pneumatic packing, the Federal Bureau of Mines imported a pneumatic packing machine from Germany and installed it in a mine of a cooperating company in the Northern anthracite field of Pennsylvania. This report covers the second in a series of experiments in applying pneumatic packing for controlling strata movement (subsidence) above mine workings in the Pennsylvania anthracite region. The first experiment2/ was begun in January 1950, in a section of the mine where about 50 percent of the original coal remained in the form of pillars; since the company did not plan to mine the pillars in this particular area, pneumatic packing of the chamber voids was done for test purposes only. During this initial test the machine was operated on 204 shifts, and 652,400 cubic feet of breaker refuse material (22,834 tons) was packed into the voids of 16 chambers. The work was completed in December 1951.

Jan 1, 1956

By D. M. Carris

Since the Buffalo Creek incident in February, 1972, Federal and state environmental agencies have had the pressure on the coal industry in the Appalachian area to close the coal processing plant water circuits. In an attempt to comply with this requirement, Eastern .Associated Coal Corp. decided to install a vacuum disc filter system at its Kopperston plant to eliminate the tailings pond and reduce the amount of plant make-up water. It was recognized at the time that the plant static thickener tailings would be a very difficult slurry to dewater because of its unusually high clay content. The following is a case history of the Kopperston installation and the refinements Eastern has made in its vacuum disc filter operation to increase efficiency.

Jan 1, 1979

By Helen Francis

Over the last decade, lower ore grades and deeper mine environments have demanded that mining companies develop new technologies (tools and processes) to ensure a mine?s economic sustainability. At Inco Ltd., this demand has lead to the focus of technological development within the area of automation. Delineation (Drilling and Interpretation) is a key step in the determination of ore grade and location and therefore was chosen as a priority area for enhancement through automation. Focusing on the tools (the diamond drill) automation, significant benefits have been consistently achieved in terms of productivity, process efficiency, operational safety, cost reduction, component life cycles and machine reliability. It is suggested that optimum benefits have yet to be achieved, and will not be achieved until the human aspects of automation have been properly addressed. Since project inception, the human aspects of automation were recognized as critical to the success of the diamond drill automation project. However, it was only upon the installation of the Automated Diamond Drill in the field and its continued use on a daily basis that this issue received due attention. The human aspects of automation can be broadly addressed as economic, physical and psychological. This paper, with examples from the field, will discuss the human aspects of automation in each of these areas. The paper will draw from observations and experiences acquired throughout this project and recommend implementation strategies that should be utilized in future automation projects to enhance both the acceptance of automation and the success of the automated process itself.

May 1, 2002

By John B. Gayle

The Bureau of Mines has designed and constructed an experimental coke oven, using a commercial oven as a model where practicable. Because the rate of carbonization is important in determining the quality of the coke produced and may affect the "mount of pressure developed during carbonization, particular attention was given to those elements of the design that govern the heat transfer to the charge. The new oven deviates in design from most existing test ovens in that the charge is full width (17 inches), the heating walls ore constructed of 4-1/2-inch silica brick, and zoned, heat-input arrangements compensate for heat losses at the ends, top, and bottom of the charge. This report describes the oven, which was designed by H. S. Auvil and installed under his direction, at the Southern Experiment Station, Tuscaloosa, Ala., while he was supervising, engineer, Coke Section. It gives the results of a limited number of carbonizing tests. These results indicate that the main objective in designing and building this oven, that off duplicating commerical, slot-oven carbonizing conditions, has been accomplished; if coke-discharge conditions simulate commercial-oven conditions, the cokes from the experimental oven arc very similar to oven coke, in soma tests being fully as close is duplicate tests from a Angle batch of coke.

Jan 1, 1952

By J. Appleby

This paper reviews earlier in-plant testing at the Sidbec-Normines pelletizing plant at Port Cartier, Quebec, Canada. It describes the result of the more prolonged use of coke breeze during recent months and in addition, the effects of varying dolomite and coke additives upon the metallurgical properties of the pellet production have been studied. Mention is also made of some brief test work carried out to use peat moss as a carbonaceous additive to the pelletizing process and in particular the plans for future work in this respect. Earlier laboratory pot-grate test work had indicated that a production rate increase of between fifteen and twenty percent was a practical possibility, or alternatively that the plant could be run at design rating with significantly lower energy consumption. These energy reductions were of the order of ten to fifteen percent for fuel and main process fan power respectively. The physical and metallurgical pellet properties for both blast furnace and direct reduction furnace use were little affected by the production rate increases, and were actually somewhat improved when practicing maximum energy conservations. Pellet properties could be further improved by not extracting the maximum energy economy. Two phases of carefully controlled in-plant testing were run to assess the effect of energy conservation under plant conditions. These two phases of testing confirmed that an overall fuel saving of approximately fifteen percent could be realized, with a reduction in the Bunker C oil consumption of about forty-five percent, and a reduction in main process fan power of approximately ten to fifteen percent. The present scope of work is aimed at establishing the use of varying levels of coke addition up to about one percent under normal plant operating conditions.

Jan 1, 1980

By Warren H. Weisz

A cement, in the broad sense, is any substance which will cause various materials to adhere to each other. Clay was probably the first material to be used by man as a cement or binding agent. Water occurs in or is mixed with the clay to make it plastic, so that it can be formed in place. The sun and air remove the water from the clay and on drying strength is developed. The clays unless fired are not too resistant to water, therefore, their use is best when restricted to dry areas. Gypsum used as a cementitious material is not the subject of this paper, but its use dates back thousands of years. Gypsum mortars were used by the Egyptians in building such massive masonry structures as the pyramids. The Egyptian mortar consisted of a mixture of sand with burned gypsum (of an impure type of 81.5 per cent calcium sulphate and 9.5 per cent calcium carbonate) for the cementitious material. The burning of this type of cementitious material took place at relatively low temperature. These burning reactions will be covered later when the dehydration of gypsum is discussed. The setting of the partially dehydrated gypsum is considered to be crystallization from a supersaturated solution which deposits crystals of dihydrate (gypsum). In low water-content mixes, the interlocking of the needle-like crystals helps to produce higher strengths. Slaked lime made from limestone burned at higher temperatures (1648 F is generally considered as the calcining temperature, although under certain conditions incipient calcination will take place at 1250 F) is another early-period cementitious material. During slaking with water, a colloidal or amorphous hydrated lime is formed. When it is allowed to dry, it hardens and develops low strengths. On exposure to the carbon dioxide of air in the presence of some moisture, carbon dioxide is adsorbed and part of the calcium hydroxide is converted to calcium carbonate. Structures in which a lime mortar is used continue to grow in strength as this reaction proflesses. Hydrated lime has the disadvantage of not setting under water.

Jan 1, 1960

By S. M. Shelton, W. A. Calhoun

"INTRODUCTION Discovery and development of a southwestern Arkansas quicksilver district are recent history. In July 1930 4/, a specimen was discovered near the Little Missouri River in sec. 1, T. 7S. R. 26 W., which was identified as cinnabar. In the summer of 1931, Leo Yount began prospecting for cinnabar near the Little Missouri River. In the fall of that year he operated a small three-tube retort near the present Parker Hill mines and produced several flasks of quicksilver. Yount optioned a considerable block of ground containing the best showings in the Little Missouri River area, and on February 19, 1932, he and W. C. McBride, Inc., of St. Louis, Mo., formed the Southwestern Quicksilver Co., which was the largest producer in the district until operations ceased in September 1934.The Southwestern Quicksilver Co. installed a rotary furnace on Parker Hill in April 1932, which treated ore from the three principal mines Gap Ridge, Parker Hill, and Parnell Hill. In 1934 production was entirely from the Gap Ridge and Parker Hill mines. Nothing was done at Parnell Hill except a little small-scale work on a share basis.Mercury Producers, Inc., later took an option on the holdings of the Southwestern Quicksilver Co. and in June 1935 began operations. The company produced considerable quicksilver before the lease and option were surrendered in the summer of 1936. Most of the work of Mercury Producers, Inc., was on Parnell Hill, but some work was done on Parker Hill and at the Bell prospect on ground not controlled by the Southwestern Quicksilver Co."

Mar 1, 1942

By D. Marcus

A methodology was developed wherein. the increase in compressive strength, mineralogical changes and pore water composition were all studied simultaneously as a function, of moisturized spent shale curing time. From these results the relationship between the nature of cementation process and the composition of pore water was established. Heavy metals were entrapped in the cementing constituents and the pore water became mainly a solution of alkaline sulfates. While the specific data are applicable only to the material studied, the methodology and general conclusions are useful for evaluating the environmental factors in spent shale disposal and expected leachates composition.

Jan 1, 1984

The support of the roof in coal mines remains a critical safety issue with 3 fatalities from roof falls in 2007 and 430 injuries from roof falls in 2006. A snapshot survey by the authors of room design and support details as well as unplanned falls of ground in the industry revealed some useful data concerning support use, seam details, fall dimensions, bolt lengths and spacing and the stand-up time.

Jan 1, 2009

By A. Fahimifar, H. Soroush

Abstract: Triaxial tests were conducted on the schist specimens with various anisotropic angles under confining pressures of 0, 7 and 15 MPa, and axial stress-axial strains, were measured and plotted for various conditions. The results obtained reveal the effects of schistose on the strength and deformability of the rock very clearly. Peak strength of the specimens for 00 and 900 schistose orientations are nearly the same. Modulus of elasticity of this rock varies with anisotropic angle. For 0 orientation modulus of elasticity increases to a maximum. Confining pressure increases the peak strength and improves the rock deformability. However, this effect is not the same for various orientations, and there are no similar trends for each anisotropy direction. Analysis of the results shows that consideration of a linear failure criterion such as Mohr-Coulomb is appropriate for the prediction of rock behaviour up to 10 MPa, rather than a non-linear one. The analysis also reveals that the friction angle and cohesion are affected by the anisotropy orientation, and this effect is more important for the cohesion than the friction angles. Resume: Les esseys triaxiales sur les echantillon d un roch schist avec les differents angles non-isotrop sous les tension lateral zero et sept et qoinze mega pascal (mpa) est fait et les covtraite et allongment unitaire sont mesure et leur curues est destine sous different condition les resultats obtenues montre les effets du schistosite sur le resistance et le ductilite vissiblement. Le resistance final sur les echantilions pour les angles o degre et 90 degree est equivalent. Le modoule d elasticite de ce roch sera difere par a port de l angle de stratification. Pour l angle o degree le valeur de modoule est le maximum. le pousse lateral augmenterai le resitance final, et sera amilterai le toleran le de ductilite. Mais cette effet bn est pas unigue pour les different stratification, et pour les diferents directions no– isotrop it n y a pas le meme solution. L analyse des resulitats montre que le criterre de ruin comme mohr–colomb est moderate pour le pousse lateral jusq av lo mega pascal , et ce n est pas neccesaire d utiliser de criterre no–linear . Cette analyse aussi montre que l angle de frottement et cohsion est en relation de la direction no–isotrop, et cette effet est olus important pour le cohsion par a port de l angle de frottement . Abriß : Dreiachsige Prüfung wurde auf den schist Exemplaren mit verschiedenen anisotropic Winkeln unter Bestätigen von Drücken von 0.7 und 15 MPa geleitet, und axiale Spannung axiale Spannungen, wurden gemessen und für verschiedene Bedingungen wurde geplant. Die Ergebnisse haben die Wirkungen von schisocity auf der Kraft und dem deformability des Felsen sehr deutlich erhalten offenbart. Maximale Kraft der Exemplare für 0° und 90 sind° schistos Orientierungen beinahe das gleiche. Modulus der Elastizität von diesem Felsen ändert sich mit anisotropic Winkel. Für 0° vermehrt Orientierung modulus der Elastizität zu einem Maximum. Einschränkender Druck vermehrt die maximale Kraft und verbessert den Felsen deformability. Aber ist diese Wirkung nicht das gleiche für verschiedene Orientierungen, und es gibt keine ähnlichen Tendenzen für jede anisotropic Richtung. Analyse der Ergebnisse zeigt jener Überlegung Kriterium eines linearen Ausfalls wie zum Beispiel Mohr Coulomb passend für die Voraussage von Felsen Verhalten bis zu 10 MPa, anstatt eines nicht linear ist. Die Analyse offenbart auch, daß der Reibung Winkel und Bindekraft werden beeinflußt von der anisotropic Orientierung, und diese Wirkung wichtiger für die Bindekraft ist, als der Reibung Winkel

Jan 1, 2003

By A. C. Richardson, G. D. Coe, B. M. Bird

"The Hull mine of the De'Bardeleben Coal Corporation is located in the Warrior field, in Walker County, Ala., about 25 miles northwest of Birmingham. The Mary Lee bed at this point is coking coal and has been used in the manufacture of by-product coke, but at present it is sold exclusively as a domestic and locomotive fuel.The data in this paper, which is the third in a series on the washability of Alabama coals,5 have been obtained in connection with an exhaustive study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators. The paper contains screen-sizing and float-and.-sink tests of a representative sample of run-of-mine coal, and flakiness tests and crushing tests of certain sizes.In addition, complete analyses of the ¾-inch to 3/16-inch size, raw coal, together with ash fusibility tests of the float-and-sink fractions have been made; those results are given in Tables 1 and 2. Since they indicate that the pr ration problem, like that at Lewisburg, Ala., is one of ash reduction, the further tests and the discussion have been restricted to that subject."

Apr 1, 1931

By S Jahanshahi, D R. Swinbourne

A knowledge of the value of the activity coefficient of cobalt oxide in slag as a function of composition and temperature is necessary if effective strategies are to be devised to maximise the recovery of cobalt in nonferrous smelting processes. This work reviews previous studies and shows that comparison and evaluation of the results is hampered by variations in the choice of standard states for the species. Published results have been recalculated to a common set of standard states with a preferred value for the Gibbs free energy of formation of cobalt oxide. It has been shown that the value of the activity coefficient of cobalt oxide referred to the solid standard state in iron silicate slags is approximately two, at temperatures from 1523 to 1623¦K. It is suggested that some contradictory results are most likely due to errors in the measured partial pressure of oxygen.

Jan 1, 1998