Search Documents

By Thomas C. Anderson

Thirty-four retaining walls are part of the $46 million upgrade of a 1942 depressed highway in Highland Park, Michigan near Detroit. This project will close a missing link between two newer roadways, I-75 and the John Lodge Freeway. The existing 75 ft. wide, six lane Davison Freeway is being replaced by a eight to ten lane, 200 ft. wide depressed highway in a limited right of way. The highway will be 20-25 ft. deep and 1.5 miles long. A design/build decision by the Michigan DOT saved about 37% of the engineers estimated cost of $19 million for the walls. The successful pre-qualified specialty contractor utilized an innovative solution for the walls consisting of tiedback/cantilevered walls on the north side and mechanically stabilized earth walls on the south side. All of the walls have an identical cast-in-place architectural facing.

Jan 1, 1999

By F Linares, B De Waele, K Bischoff, M Lacorde, G Loveday

Recent exploration has identified the presence of detrital iron deposits (DIDs) associated with banded iron formation (BIF) units in the north-west of the Congo Craton, Gabon. The regional geology comprises a complex of granitoids and gneisses assigned to the Archaean Chaillu Complex, within which older slivers of lower amphibolite-grade greenstones are preserved including muscovite-biotite-garnet-bearing felsic schist, amphibolite and BIF. These units are typically overlain by several metres of residuum comprising colluvium, eluvium and duricrust. The residuum is overlain by a regionally extensive loess cover from 2 m to 10 m thick.The DIDs occur within the weathered residuum as mostly unconsolidated gravels with lesser canga (CAN) duricrust draped over deeply weathered hematite. Head grades are in the range of 45 to 52 per cent Fe. Fresh BIF, located from 30 to 50 m below surface, is comprised of magnetite-quartz±amphibole. The detrital iron gravels are comprised of rod- and plate-shaped clasts of hematite (martite)-maghemite-goethite composition, in a ferruginous sand to clay-sized matrix. The DID form ridges and plateaus that coincide with magnetic highs defined using high-resolution ground magnetic surveys.The field relations and petrography indicate that the detrital iron accumulations are the result of weathering (including enrichment) and erosion of primary BIF. This includes removal of quartz, further oxidation and re-cementation of BIF to form ferruginous caprock. This cap and the in situ oxidised BIF were subsequently disaggregated and liberated, and further weathered to form the detrital iron accumulations.Metallurgical test work on bulk detrital iron samples has shown this material can be upgraded to lump and fines iron ore products with grades of 62 to 65 per cent Fe using simple scrubbing and wet screening, followed by dense media separation of the -1 mm fraction, with overall mass yields from 75 to 85 per cent. The test work indicates a high ratio of lump to fines products, sometimes exceeding 50:50.CITATION:De Waele, B, Lacorde, M, Bischoff, K, Loveday, G and Linares, F, 2017. Geological and metallurgical characteristics of banded iron formation associated detrital iron mineralisation in Central West Africa, in Proceedings Iron Ore 2017, pp 259–268 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Pressure drops were measured in a column packed with glass spheres and wax particles, both in random and preferential distributions. Variables investigated included wax content, gas flow rates, and temperatures.It is shown that for random distribution of wax, pressure drop is exponentially related to wax content above the melting point of wax and that below this it increases with increasing gas rate and temperature.For preferred distribution of wax the highest increase in pressure drop is obtained with horizontal distribution of wax and the least with vertical distribution.Comparison with operating blast furnace data and application of results to practice are also included.

Jan 1, 1970

By G. Adderley, A. Wetherelt

The problems of poor drilling in underground operations have been highlighted on many occasions. Incorrect collaring and poor angular deviation can all lead to an increased block size, dilution, over-break adding to both cost and time, while in a tunnelling operation sidewall damage and a poor percentage pull from a blasted round has similar consequences. This paper sets out to further investigate the ability of the laser scanner method of obtaining drill hole deviations and collaring errors at the face as described by Wetherelt and Williams (2006). Tests were carried out to compare measured inter-hole burdens from this method in comparison to that obtained using a total station survey. To investigate the ability of these methods to accurately determine drilling errors, a field test was carried out through an analysis of a series of pre-drilled blast holes of known inclination and direction. A time-motion study was also conducted for a varied number of holes to assess the usability of each method. In line with current research into blast vibration being undertaken at the Camborne School of Mines, 6 cut blasts were carried out to establish the effect of poor drilling on a blasts success to see whether an increased burden at the toe of a hole had an influence on vibration.

Jan 1, 2009

By F. Rosenblum, P. Spira

"Techniques were developed to determine the oxygen demand of sulphide ore pulps in the laboratory and in concentrators. The effect of variables which influence oxygen demand was studied, and it is shown that the oxygen demand is a measure of the degree of oxidation of the sulphide surfaces. It is suggested that in investigating the significance of oxygen in flotation, the oxygen demand of the pulp is a more suitable parameter than the dissolved oxygen content.Oxygen demand measurements are being carried out with a view to determining the effect of aeration on mill metallurgy and devising improved methods of predicting aeration requirements of sulphide ores.The importance of pulp oxidation in the flotation of massive sulphide ores has long been recognized. At the Noranda concentrator, chalcopyrite could not be floated satisfactorily without a pre-flotation aeration step because the necessary dissolved oxygen was consumed by the large amount of pyrrhotite in the ore. With aeration, pyrrhotite and pyrite were depressed by surface •oxidization, and the resulting thiosulphate level in solution gave a good indication of the end of useful aeration. 1'he present study was prompted by the need to find an alternative criterion for cases where recycled mill water may contain a relatively high concentration of thiosulphate. Preliminary experiments suggested that the rate of oxygen uptake by the pulp -its oxygen demand -might be a practical measure of the end point of aeration as well as a significant parameter in the flotation of massive sulphide ores.Although it has long been realized that oxygen is an important variable in flotation, analytical difficulties precluded detailed plant investigations. Measurements of' dissolved oxygen in mill pulps were first reported by Ralston(i) in 1929. A titration method was used, and because of the delay occasioned by the preparation of clear solution samples, the values obtained were believed to be low. It was quite evident, however, that pulps in the grinding circuit had a lower oxygen content than in flotation. More recently, Woodcock(2,3) used a polarographic probe to carry out oxygen surveys in six Australian concentrators and he generally observed a similar pattern. A large number of other solution parameters were monitored, such as pH, redox potential, reducing power, and reagent and metal concentrations, with the aim of detecting correlations among the measured variables. A few potentin.lly useful relationships were found ""or specific operations in certain plants."

Jan 1, 1974

By Edward Thomas

Yucca Mountain Overview The U.S. Department of Energy?s Yucca Mountain Project is a geologic repository project designed to receive, handle, package, transport, and emplace spent nuclear fuel and high level radioactive waste. The planned repository would be located in Yucca Mountain on the western edge of the Nevada Test Site, about 90 miles northwest of Las Vegas, Nevada, and would include both surface and subsurface areas. Yucca Mountain rock formations consist of successive layers of volcanic rocks (called tuffs) approximately 14 to 11.5 million years old, formed by eruptions of volcanic calderas to the north. With the volcanic rock the potential for methane emission is not an issue and the subsurface repository is a non-gassy (methane) classification. This paper will provide a summary of the development ventilation system design that provides fresh air for subsurface construction activities, and the emplacement ventilation system design that removes heat generated by the waste packages. The subsurface layout, illustrated in Figure 1, contains 108 emplacement drifts, one Performance Confirmation(PC) observation drift, nine intake/exhaust shafts, and three access ramps. The existing Yucca Mountain facilities, shown in bold lines in Figure 1, include a 7.8 km long, 7.62 m (25 ft) diameter U shaped tunnel that is formed by the North and South Ramps at both ends of the Exploratory Studies Facility (ESF) drift and a 1.5 km long, 5.0 m (16.4 ft) diameter Enhanced Characterization of the Repository Block drift (ECRB) that were constructed from 1994 through 1998. These drifts were used for site characterization activities and have been incorporated into the subsurface repository configuration. The unexcavated perimeter access main and exhaust main drifts are typically 7.62 m (25 ft) diameter TBM excavations and the emplacement drifts are 5.5 m (18 ft) diameter TBM excavations. The turnouts leading into the emplacement drifts are to be excavated by either mechanical, or drill and blast methods and serve as the launch chambers for the emplacement drift TBM excavations.

By E. H. Myrhaug, K. Aasly, T. Malvik

Six different types of quartz and quartzites used as raw materials by ferroalloy plants have been investigated with respect to their thermo mechanical properties. In order to investigate the effect of the thermal shock caused by the rapid heating of quartz when it enters the furnace, the following techniques have been used for both in situ investigations and investigations of pre-heated quartz: -Heating stage microscopy for in situ observation of heating effects. -Shock heating of quartz in an induction furnace An optical microscope-mounted heating stage was used for in situ observations of the microscopic effects of heating up to 1300 ºC. The effects of heating were observed at different temperature intervals in different samples. The main temperature intervals were below 573 ºC and above 1000 ºC. The cause of the observed effects is interpreted as fluid inclusion decrepitation for T<573 °C and structural implications (micro cracks, grain boundaries and remaining fluid inclusions) at T>1200 °C. Shock heating of the samples was carried out in an induction furnace to 1300 ºC for ten minutes. The effects of the heating were studied with different techniques such as direct observation during and directly after heating, optical microscopy and XRD. Combined transmitted and fluorescence light microscopy shows that the heated quartz show an opening of the grain boundaries and evenly distributed micro cracks that were not present in the unheated reference samples. In some of the heated samples, weak generation of cristobalite was detected by XRD.

Jan 1, 2007

Significant advances have been made in the design of centrifugal slurry pumps that are used for pumping high-density viscous and paste slurries. This paper presents the results of a series of centrifugal pump performance tests that were conducted using an FLSmidth 6 x 4 Krebs millMAX centrifugal pump. The pump was fitted with a dry mechanical seal to prevent dilution of the slurry from gland service water, as the theology of the slurry is sensitive to small changes in slurry density. Tests were done using paste kaolin slurry with Bingham yield stress values between 578-1 120 Pa and plastic viscosities between 728 and 1491 mPa.s. The viscous properties of the paste during each pump test were measured using a rotational viscometer. Pump head and efficiency de-rating were measured and compared to the correlations of Walker and Goulas (1984). The test data shows the pump&apos;s best-efficiency point (BEP) changes and shifts to the left of the performance curve. The pump efficiency decreases as the slurry yield stress increases. The head de-rating data shows more head de-rating at the low flow rates compared to the high flow rates for the high viscosity slurry, which is in line with the findings of Walker and Goulas (1984). This paper demonstrates that it is possible to pump very viscous, high yield stress slurries with limited head and efficiency de-rating using centrifugal pumps, provided that positive suction conditions are maintained at all times.

Jan 1, 2012

By G. F. Jenkins, P. S. Hobden

Toronto as a geographical area provides an exceptionally wide variety of subsoil stratiphication. Tunneling consequently required a very wide range of adaptabilities to meet its changing conditions. This discussion will provide a summary of work performed in both earth and rock formation using three of our recent works to describe a Contractor&apos;s experience. The general subsoil stratigraphy is known to consist of deposits laid down during the Illionian Glaciation followed by the Samgamon Interglacial Stage and finally the Wisconsin Glaciation. All these deposits are underlain by shale bedrock of the Dundas formation. As a whole the Dundas formation is predominantly a greyish blue, thinly bedded shale. The engineering characteristics of the shale vary considerably, however, between a blue clay (argillaceous) shale and a much lighter (in colour) silty and sometimes sandy (arenaceous) shale, and occasional limestone layers. The Illionian deposits are usually found to be layers of pebbly clay till and an overlaying layer of contorted varved-clay. These glacial deposits can be overlain by a thick layer of sandy silt to silty sand which is identified as the Samgamon Interglacial sediments. Because of the action of erosion the Wisconsin till sheets, many times separated by interstadial sands, can vary greatly in their number of layers from zero to three or more.

Jan 1, 1997

By Wayne Trudel, Lloyd McEvers, Lori Clarke, Eric Saderholm, Charles Lynn Bolin, Leroy Schutz

Newmont mine geologists in Nevada are most proficient when applying technical expertise with multi-departmental teams in three main settings. The first is value creation through near-mine discovery, development and reserve conversion. Since 1986, geologists have created substantial net asset value in developing more than 1.35 kt (43 million oz) into quality Nevada surface and underground gold reserves. The second setting is value realization by supporting mine operations with ore control, selective mining, reconciliation investigations and strategic planning. The investment of technical research on reconciliation investigations led to new concepts and practices that highlighted opportunities for large revenue and reserve gains. In 2002, more than $65 million in projected revenue was added to the Gold Quarry south layback. Kriged mine polygon construction and controlled blast heave at the Lone Tree Mine provided millions of dollars in mining efficiencies. High-quality geologic advice in selective mining at the Twin Creeks Mine helped obtain $4.3 million revenue gains throughout 2002-2003.

Jan 1, 2004

By Lin Daoyi

In this paper, we have adopted the high pressure jet-grouting curtains to seal the sea-water, and to consolidate the wall of the well for deep foundation diteh, make a pladge of building and construction of deep foundation was primarily on progress without water. This paper, we have been given a test for pumping water under mainly the circumtances of sealing condition and to report in advance the capacity of seawater seeping into the gam curtains in the process of building and construction of deep foundation.

Jan 1, 1991

By D Craw

Bulk ore tailings from the Macraes gold mine gold extraction process are stored in a large (ca 0.6 km2, 80 m deep) mixed tailings impoundment whose pH is maintained near 8 by natural rock neutralizing capacity. The mixed tailings will be stored in this impoundment in perpetuity after mining ceases. Confidence in the long term environmental stability of these tailings can be gained from examination of mineralogically and chemically similar geological situations in the immediate vicinity. A sequence, typically about 5 m thick, of sands and gravels derived from the Macraes mineralized zone 12 000 to 28 000 years ago contains rounded detrital sulphide mineral grains which are unoxidized despite close proximity to the surface and occasional incursion of oxygenated waters. Saturating water pH is currently 7-8. Sands with 0.2 to 0.8 wt % organic carbon host sulphate-reducing bacteria (SRB), and localized cementation by authigenic framboidal pyrite has occurred. Comparison of the 28 000 year-old sediments with the modem tailings suggests that similar chemistry will prevail, possibly with deposition of authigenic pyrite in the tailings, in the long term. As long as the present slightly anoxic and circumneutral pH environmental conditions are maintained in the mixed tailings dam, sulphide decomposition and acidification are unlikely. These sediments provide a plausible geological analogue for long-term benign storage of the mixed tailings impoundment.

Jan 1, 2000

By Sam Bang Jr, Rodney Burke

As mining progresses in the West, the depth of material has increased, making highwall stability a major factor in safety and production. The Jim Bridger Coal Mine’has made highwall stability a priority, concentrating on safety as well as increasing and improving production. Overburden depths are increasing dramatically; the geological environment consists of medium to sot? material, faulting, water, and current pit alignment not favorable to joint planes. Angle drilling the presplit at 20 degrees became necessaryas vertical presplit drilling produced wall failures.

Jan 1, 1998

Reduce accidents associated with handling of the electrical trailing cable and the water hose on mining equipment. Approach Two reels were mounted on a loading machine to store and release the lines as required during face operations. How It Works A hydraulic motor, which is actuated by a treadle valve in the operator&apos;s cab, controls the reel on which 50 feet of electrical power cable is stored. A spring motor resists unwinding of the other reel on which 50 feet of water hose is stored. Both reels are mounted on the right rear of the loading machine. See Figure 1. Following common mining practice, the cable and hose are anchored to fixed points at the first intersection outby the face. Tramming forward causes the cable and hose to be pulled from the reels. Depressing the treadle valve causes the electric cable reel to turn and wind-in any slack in the cable. The spring tension on the water hose reel automatically rewinds the water hose when the loader is trammed in reverse.

Jan 1, 1978

By I F. Bell, K P. Hammerschmid

Well planned and executed environmental management plans can reduce life-of-mine operating costs and the need to deal with major environmental issues at the time of mine closure. With proper planning during the exploration, feasibility and execution phases of a project, final closure costs can be reduced. The reduction of closure costs should be considered during exploration and initial feasibility studies and when process facilities, waste rock dumps and tailings impoundments are designed. During the mining of the resource, closure cost reduction will depend on effective and efficient environmental management plans for ongoing land clearance, segregation of mine waste materials, management of mine site water and workshop wastewaters, and the establishment of progressive rehabilitation strategies. These issues are the responsibility of planning, production, technical support and maintenance personnel at an operating site. The successful implementation of environmental plans will ensure that all impacts are reduced and that closure issues with major cost implications are addressed prior to closure of the mine.

Jan 1, 1995

By B. Larsen, S. Z. Nascimento, K. Fidje, J. P. M. Amaro, H. Gran

Safe and good operation of Søderberg electrodes is dependent upon high quality electrode paste coupled with correct electrode operating procedures. Good electrode performance depends further on proper melting and densification of the electrode paste. The melted paste should form a dense and viscous layer that prevents gasses from the baking process to move upwards. Both paste cylinders/blocks and briquettes can be used, but the procedures may differ between the various types of paste products. For briquette columns the formation of the important viscous layer is obtained through melting and densification of the briquettes. By basic rheological studies of electrode paste and by laboratory tests of briquette beds at isothermal conditions we have achieved a better understanding of the melting process. The effects of temperature gradients, pressure and friction between the briquettes and the electrode casing have also been evaluated qualitatively in pilot scale experiment and in industrial scale tests. The paper shows that melting and densification starts at a considerable lower temperature than the pitch softening temperature. It is concluded that the formation of a briquette electrode column depends on parameters as temperature, briquette column pressure and the friction. Operating conditions influencing the above parameters should be defined and established for each specific furnace operation. Such factors are e.g., charging and slipping procedures, column heating and electrical conditions.

Jan 1, 2004

By Mark Rybak

On August, 31, 2006, Tropical Storm Ernesto hit the City of Richmond, Virginia. The Battery Park area was hit particularly hard, as flooding forced an evacuation of the area. A large sinkhole collapsed a sewer line in the Battery Park area, blocking the pipe and causing more serious flooding. This case history describes the fast track design, bidding, and construction of an emergency tunnel to bypass the collapsed sewer. Innovative value engineering, tunneling and shaft sinking methods, and final lining design all contributed to the success of this project. The storm inundated Richmond, Virginia with up to twelve inches of rain in some areas causing widespread flooding and damage. One of the hardest hit areas of Richmond was Battery Park. A major trunk sewer in the Battery Park area collapsed causing local combined sewer and storm-water flooding. The collapsed sewer was an 8&apos;-3" wide by 9&apos;-6" high arch sewer that was constructed in the nineteen twenties and later filled over with municipal solid waste and a soil fill cap to current elevations. A sinkhole was created in the area of collapse approximately sixty feet deep and one hundred feet in diameter causing the existing arch sewer to become blocked. As a result of this blockage contaminated flood waters reached depths in low lying areas in excess of twenty five feet. [ ]

Jan 1, 2008

The need for the hydraulic transportation of coal in the New South Wales coal industry, both from the coal face to the surface and from the coal mine to the consumer or the port for export, is explained. Details of research projects currently in progress and involving the hydraulic transportation of New South Wales coals are given together with information on the hydraulic transportation of coal in the United States of America. The potential of hydraulic transportation as a viable alternative to the proposed expansion and upgrading of the New South Wales railway system to meet the projected New South Wales coal production to the year 2000 is described.

Jan 1, 1980

By Anil K. Ray

This paper discusses in situ studies conducted at an Illinois Basin room-and-pillar coal mine to evaluate the performances of three different types of bolts under similar geologic conditions. The bolt types considered were the fully grouted passive rebar (FGPR), the resin-assisted mechanical anchor (RMAB), and the fully grouted tension rebar (FGTR). During the evaluations, the three types of bolts were installed in a single entry covering a span of three contiguous pillars with almost identical geologic conditions. The performances of the three types of bolts were investigated by instrumentting the bolts prior to installation as primary supports on cycle. Additional data on roof behavior was collected with extensometers and shear meters placed near the instrumented bolts. Excluding some time lapse right after installation, the performance evaluation of the three bolt systems was based on the data collected for over a year. Based on this study, it was found that the axial loads measured in the different bolt types did not show any identifiable patterns under the prevailing geological conditions at the mine. Therefore, the assumption that active bolts must be superior to passive ones is not always valid. Even though the studied mine did not have any thinly laminated, weak rocks in the immediate roof, the passive bolts performed as well as the active systems.

Jan 1, 2012

By J. V. Simmons

Composite rock mass failures involve intact rock material as well as fracture and shear on existing defects. Experiences from open-cut coalmining in the Bowen Basin of central Queensland are that failures of this nature occur suddenly with little warning, and are much more common than classical structurally controlled failures. Geological conditions and mining practices in the Bowen Basin are described. The circumstances of a sample of composite failures are described in detail in the paper. From this experience it appears that several aspects of conventional geotechnical investigation and design practice have not contributed significantly to either predicting or controlling the risks associated with sudden failures. These practices are described as myths for reasons outlined in the paper. On the other hand, the reality seems to be that high initial stresses and stress changes caused by excavation lead by a process of extensional deformation to a critical stress condition within the rock mass, and that sudden collapse follows when that critical stress condition can no longer be sustained. It is concluded that learnings gained from underground excavations in rock may be more applicable to open pit excavations than previously thought, and that the processes of prefailure deformation require more careful study if we are to develop more reliable risk management controls.

Jan 1, 2006