Search Documents

In common with general experience in the iron-making industry overseas, Australia has in recent years suffered a deterioration in the physical quality of her iron ores in their suitability as a direct blast furnace feed. The increasing amounts of fines and the more friable nature of lump ore, especially in the ore from the Cockatoo Island deposits in Yampi Sound, Western Australia, have focused attention on problems of ore preparation and agglomeration, particularly sintering.Although very small pilot scale Dwight-Lloyd type sinter machines were operated at the steel-making centres at Newcastle and Port Kembla during World War II, no sizeable capacity was installed, so that ore was charged to the blast furnaces almost entirely unscreened, and the resultant flue dust was stockpiled.Towards the close of the war, the pilot plant at Newcastle was replaced by a small machine, adjacent to the flue dust stockpile, with a rated capacity of some 20 tons per hour. After approximately five months of part-time operation, this plant was closed down in January, 1945. Production was not resumed until December, 1950, when, due to a temporary ore shortage, it was decided to supplement available ore with sinter produced from the large flue dust stocks of about 300,000 tons. In spite of mechanical and process difficulties, inherent to the design of the plant, operation was continued on a two-shift basis, with several shutdowns for extensive overhaul and plant alterations, until September, 1954, when production was put on a three-shift basis. Addition of Yampi ore fines to the sinter machine burden was not commenced...

Jan 1, 1957

By Jan E. Nesset, Julie Fournier, Jorge Torrealba, Colin Hardie

"Gas dispersion studies have been used to benchmark and optimize plant flotation performance for more than a decade, although this technology is not as widely in use as it likely should be based on the significant improvements that have been reported. Part of the reason may be a general lack of awareness within the industry of just what these improvements have been. This paper reviews a number of the reported case studies, groups them into categories of improvement, and draws some general conclusions. The paper will be of interest to plant engineers and technology providers seeking new approaches and tools for improving their own and clients’ processes.INTRODUCTIONThe sector of flotation hydrodynamics that is now known as gas dispersion technology, and the corresponding terminology, had its beginnings in the 1980’s and early 1990’s in the laboratories of McGill University where the students of Prof. J.A. Finch and Dr. C. Gomez conducted studies of gas holdup, superficial gas rate and water recovery on laboratory flotation columns (Laplante et al., 1983; Xu et al., 1991;, Banisi and Finch, 1994; Finch et al., 1999; Nesset, 2011). Sensors were developed for gas holdup (eg), gas rate (Jg) and bubble size (Db) distribution (Tavera et al., 1996: Finch et al., 1999; Dahlke et al., 2001; Chen at al., 2001; Hernandez-Aguilar et al, 2002, 2005). The sensor measurements were rapidly adapted for use in mechanical flotation machines in plant environments (Gomez and Finch, 2002; Gomez et al., 2003; Cooper et al, 2004; Torrealba-Vargas et al, 2004; Nesset et al., 2007). Somewhat parallel developments were being conducted by Gorain and colleagues at the University of Queensland’s JKMRC on pilot and industrial flotation machines using the McGill approach but utilizing alternate sensor designs for eg, Jg and Db (Gorain et al., 1997, 1999; Schwarz and Alexander, 2006) to link flotation kinetics to bubble surface area flux (Sb). Early industrial applications were those led by the university teams from McGill (Canada), the JKMRC (Australia) and the University of Santa Maria (Chile) at plants in North and South America, Australia, South Africa, Asia and Europe. Industrial organizations that brought the technology on-board in the early 2000’s included Teck Resources (then Teck Cominco), COREM, Vale (then Inco), Anglo American Platinum. Several of the major flotation cell manufacturers also purchased the McGill bubble viewer technology for their own equipment studies. The sensors have continued to evolve with multiple and continuous measurement of Jg (Torrealba-Vargas and Finch, 2006, Bartolacci et al., 2008), gas holdup by acoustic means (O’Keefe, 2007) and a combined Jg-Db device called the Anglo Bubble Sizer (Harbort and Schwarz, 2010). A review of the gas dispersion technology use and development have been provided by Gomez and Finch (2002), Harbort and Schwarz (2010) and Nesset (2010)."

Jan 1, 2015

By F. J. Plaul

The dominating technologies for steelmaking are the basic oxygen furnace (BOF or LD process, Linz-Donawitz) and the electric-arc furnace (EAF). The main iron input materials for both are liquid iron as hot metal, or solid iron as pig iron, DRI (direct reduced iron), HBI (hot briquetted iron) and scrap. Hot metal, pig iron (i.e., solidified hot metal) and DRI/HBI are virgin iron materials, which have to be produced from iron ore by so-called ironmaking technologies. The family of ironmaking technologies includes three process routes: blast furnace, smelting reduction and direct reduction. Driven by steadily increasing costs of raw materials in the last two decades, the sector has seen a number of new developments in ironmaking technologies, developments based on fluidized-bed technology. The main advantage of a fluidized-bed technology is that fine iron ore can be directly charged to the process without prior treatment; it does away with agglomeration and its concomitant cost, a step practised in blast-furnace, COREX® and MIDREX® processes. With Posco of South Korea, Siemens VAI Metals Technologies has successfully developed the FINEX® process, a smelting reduction based on the direct use of iron ore fines to produce hot metal. The key technology is the four-stage, bubbling fluidized-bed-reactor system, in which fine iron ore is reduced to DRI fines in a countercurrent flow with a reducing gas generated by coal gasification. Beside surveying the current state of the art, this paper discusses the technological principles of smelting-reduction and direct-reduction processes. The status of FINEX® and the outlook for further developments are described. Crucial to the successful development of the new ironmaking technologies for the direct use of fine ore was the scaling up of the fluidized-bed reactor system, which demonstrated new design features.

Jan 1, 2009

By I. W. Farmer

Weightings and water inflows into longwall workings often occur together, giving rise to discussions on their relative genesis. Case histories are introduced which indicate that most water inflows are associated with heavy weightings. Resultant large releases of energy can lead to extensive vertical fractures, which can drain water from aquifers or other sources, such as separation accumulations, onto the face. Effectively control of water inflows in these cases depends on face support and weighting control.

Jan 1, 1996

By Mokhinabonu Mardonova, Yosoon Choi

Open-source technology for supporting the Industry 4.0 has become the target of academic research in many sectors. This study reviewed the trends of open-source technology, its forms, and some industrial applications. As a case study using open-source hardware and software for the mining industry, this study proposed a low-cost environmental monitoring system for non-metallic underground mines to support mine safety and occupational health issues. The system was developed using open-source hardware, Arduino and 3D printer, to design the monitoring device. An open-source software, MIT App Inventor, was used for developing an Android application for smartphones to enable remote communication with the system. Field experiments were conducted at an underground tunnel and a non-metallic underground mining site to assess the performance of the system in both mobile and static modes, respectively. Although a few limitations related to the precision of the low-cost dust and gas sensors still exist, the findings of the experiments show that the mining industry can benefit from open-source technology deployment when considering cost factors

By Joram M. Amir

Even when they are cased! [ ] In bored piles, as well as in drilled shafts, and in caissons too, defects will occur! [ ]

Jan 1, 2001

By Harold P. Rue

The problem of removing hydrogen sulphide from natural gas has become within the last few years one of major importance to the natural gas and petroleum industry. Several gas fields in the United States produce natural gas containing hydrogen sulphide, and a number of oil fields produce gas which contains hydrogen sulphide. 3 The percentage of hydrogen sulphide in natural gas produced in these fields varies from a fraction of 1 per cent t6 as high as 20.5 per cent by volume. 4 Hydrogen sulphide is probably the most toxic gas associated with natural gas,5 and from the standpoint of health and safety it is important that the hydrogen sulphide be removed if the gas is to be used for domestic purposes. Hydrogen sulphide, besides being toxic and therefore a hazard to animal life, is under certain conditions an active corrosive agent and very destructive to equipment. 6 The annual loss caused by the corrosive action of hydrogen sulphide on equipment amounts to hundreds of thousands, perhaps millions, of dollars. 7 The largest percentage of natural gas produced in the United States comes from wells which also produce oil. This associated gas invariably carries with it light fractions of petroleum, which when separated from the gas, condense to the liquid form at ordinary temperatures and pressure. Commercial application is made of this natural condition, and "wet gas" is processed to obtain so-called natural gasoline by employing the principles of absorption, adsorption, or compression and subsequent expansion accompanied by cooling. In the manufacture of natural gasoline from wet gas which contains hydrogen sulphide, if this contaminating gas is not first removed, some of the hydrogen sulphide may oxidize to form free

Jan 1, 1932

By M. J. Beus, B. Stewart, S. Iverson

Ore-pass hazards are a significant safety problem in US underground metal mines. From 1975 to 1995, nearly 75% of injuries during pulling or freeing of ore-pass chutes were related to falls of broken rock or the use of hand tools. Risk assessment methods are being used to identify the most probable causes of ore-pass failures and analyse the factors that result in malfunctioning or safety reduction. Static and dynamic loads are being measured in the laboratory and by field testing, with data from test ore passes compared with mine data to characterise true system behaviour. Computer modelling using closed-form solutions, finite element analysis and a newly developed particle flow code are being use to predict loads from ore and waste flow and impact. Preliminary results indicate that dynamic impacts may be much less than expected, as a result of damping factors, normal and shear stiffness and mass frictional characteristics

Jun 19, 1905

By M. W. Hildyard

The aim of this paper is to demonstrate that active seismic measurements could have an impact in helping solve rock engineering problems experienced in the South African mining industry. The paper presents a variety of experimental and numerical results where seismic waves show clear differences in wave-speed and amplitudes due to different degrees of fracturing. It presents results from the ?Omnibus? project commissioned to develop new ultrasonic technologies for diagnosing fracturing for nuclear waste repositories. This included using models to investigate assemblies of cracks where the effects of crack density and crack size on waveforms are shown to be coupled. Results indicate that these effects can be decoupled in the frequency domain, where the Fourier amplitude aids in estimating crack size, while the low frequency phase-difference has a direct relationship to crack density. Models are also shown to aid interpretation of waveforms by isolating geometric effects from the effects due to cracks. Two rock engineering problems experienced in the South African mining industry are investigated through numerical examples. These demonstrate that determining whether ?crush? pillars have failed and determining the degree of fracturing in the hangingwall of stopes, may be possible through the use of active seismic surveys.

Jan 1, 2005

By P. C. Carrasco

Knowing the origin of the relevant and irrelevant components of the nugget effect is essential to optimize the process under study. This paper describes the causes of the nugget effect and, its dependency on the sample support, sampling density, and on the QA/QC procedures. Several examples of natural and ?human? nugget effect are given. A method to estimate the magnitude of the relevant and irrelevant components is suggested. Finally, the economic consequences of misunderstanding the nugget effect are analysed.

Jan 1, 2010

Carbon anode cells were studied by two-dimensional computer simulation to evaluate their suitability for alumina electrolysis at high superficial current densities. The most efficient anode arrangement was needed to overcome the electrochemical disadvantages of alumina's low solubility in chlorides. Cells with packed-bed anodes might provide practical superficial current densities greater than 0.67 A/cm2 when the granule size was less than 1 cm, but in the process of electrolysis the granules within the active zone would be consumed and become smaller, affecting alumina concentration transport. For zones of very small granules a concentration-dependent model should be considered; for more complete consideration a time-dependent model can be introduced to describe the variation of granule size and its influence on mass transfer and polarisation

Jun 19, 1905

By Mokhinabonu Mardonova, Yosoon Choi

Open-source technology for supporting the Industry 4.0 has become the target of academic research in many sectors. This study reviewed the trends of open-source technology, its forms, and some industrial applications. As a case study using open-source hardware and software for the mining industry, this study proposed a low-cost environmental monitoring system for non-metallic underground mines to support mine safety and occupational health issues. The system was developed using open-source hardware, Arduino and 3D printer, to design the monitoring device. An open-source software, MIT App Inventor, was used for developing an Android application for smartphones to enable remote communication with the system. Field experiments were conducted at an underground tunnel and a non-metallic underground mining site to assess the performance of the system in both mobile and static modes, respectively. Although a few limitations related to the precision of the low-cost dust and gas sensors still exist, the findings of the experiments show that the mining industry can benefit from open-source technology deployment when considering cost factors

By K. J. Liles

Research was undertaken by the Bureau of Mines to determine the technical feasibility of producing lightweight aggregate from the waste glass fraction of municipal incinerator residues. Tests were conducted to determine the amount and optimum size of glass, the amount of sodium silicate, and the method used to form the material to be expanded. The most suitable mixture, 78 percent glass, 20 percent clay, and 2 percent sodium silicate, was pelletized and then expanded by exposure to a temperature of 1,550° F for 15 minutes The resulting lightweight material had a bulk density of 38 lb/cu ft and exhibited excellent pore structure. Concrete test cylinders made from the light weight aggregate had a unit weight of 104 lb/cu ft and a compressive strength of 2,550 lb/sq in after a 28-day steam cure.

Jan 1, 1976

By V. F. Swanson

As part of the Bureau of Mines titanium resources examination program, samples of altered rock (saprolite) and unaltered rock from the Roseland anorthosite near Roseland, Nelson County, Va., were tested for amenability to beneficiation by flotation. A flotation technique was developed to produce bulk concentrates of ilmenite, rutile, sphene, and leucoxene. It was necessary to first float apatite using oleic acid as the collector, in an alkaline pulp with dextrine as a titanium mineral depressant. The titanium minerals could then be floated from the apatite tailing, using fluosilicic acid to depress the remaining apatite, morin to depress ferromagnesian minerals (when present), and oleic acid as the collector. A bulk titanium mineral concentrate, analyzing 66.0 percent Ti02 and 0.08 percent P205, was obtained from a sample of the unaltered rock which contained 5.45 percent TiO2 and 2.81 percent P205. Overall recovery in the concentrate was 47.1 percent of the total TiO2 in the ore. About 55 to 65 percent of the saprolite sample was clay and was removed by attrition scrubbing and decantation. The apatite prefloat procedure was applied to the saprolite sands; subsequent titanium mine: 1 flotation recovered 72.2 percent of the Ti02 in a bulk concentrate containing 65.1 percent TiO2 and 0.20 percent P205.

Jan 1, 1962

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard to miners and mine operators. This type of failure, termed a "Cascading Pillar Failure" (CPF), occurs when one pillar in a mine layout fails transfering its load to neighboring pillars causing them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S. are documented. Mining engineers can limit the danger posed by these failures through improved mine design practices. Whether failure occurs in a slow, nonviolent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines, namely, the containment approach, the prevention approach, and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining.

Jan 1, 1996

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crushed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summaries of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling at the same group of quarries. OBJECT Or STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

Validation and Simulation of Optimised Compressive Crushing Ores and aggregates are used in countless applications all around in the society. The frequent and escalating usage of these natural resources requires efforts aimed at not only making do with what is available, but also undertaking actions to improve the production yield and the processes involved. This strive to improve the performance and efficiency of existing crushers and crushing processes has brought about research concerning optimisation of crushing plants as well as theoretical optimisation of crushing. Previous work shows that different applications and different materials require different compressive crushing in order to accomplish a theoretically optimal size distribution. These optimisation results, obtained by genetic evolutionary algorithms and evaluated with so called fitness functions, convey the theoretically optimal number of compressions and their corresponding compression ratios. Presented in this paper are thus some laboratory crushing tests, which are conducted in order to validate a set of previously optimised crushing sequences. More specifically, interparticle crushing sequences are carried out in a Piston-die testing equipment, where samples are sieved between each compression. The subsequent analysis of these results shows good correlation with model predictions, which combined with a comparative study between presented optimisation results and measured data from a real crusher indicate a significant potential for improvement. However, before redesigning crushers according to what is theoretically optimal, the resulting impact as well as the effects on the outcome of a crushing plant must be examined. Crushing plant simulations using the software PlantDesigner« are consequently performed. Models of existing crushers are altered, resulting in changed particle size distributions from some of the crushers in a crushing plant. Thence, it is concluded that significant gains can be made in terms of capacity, process yield and energy consumption.

Sep 13, 2010

By Raymond W. Henn

The 32nd annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, June 13-17, 2011. The field demonstration portion of the course was conducted June 16 at Baski Inc.?s yard in Denver, CO. The full-scale field demonstration presents many types of drilling and grouting equipment in operation as well as numerous grouting methods per-formed under various field conditions. As part of the field demonstration, the class was shown the proportioning, mixing, testing and injection of various cement grout mixes into sand columns under controlled and recorded conditions. These sand column demonstrations have been conducted under controlled and measured conditions each year since 1999 as part of the short course. The sand column demonstrations were conducted prior to 1999, but with less quality control and minimal record keeping of the proportioning, mixing, testing, injection pressures and the final permeation results.

Jan 1, 2011

By Leonello Sciacca

Deepening of harbours has become a priority, necessary to the ongoing operation of the wharves in the face of deeper draft merchant vessels and cruise ships. It is now standard practice in many areas to provide for harbours to be dredged to significant depths below mean sea level, in the order of 12.00 m (39 ft) for existing berths and 15.00 m (49 ft) for new wharf construction. The Ravenna Port Authority initiated a project to deepen the harbour bottom at selected wharves to a depth of 12.00 m (39 ft). In preference to reconstruction of the wharves with longer and heavier sheet piling or other equally disruptive reconstruction, they identified the structural reinforcement of the existing wharves by means of deep underwater tie rods as a possible alternative cost-effective solution. Having defined the design concept, effort was concentrated on developing the required technology. A technique, already in use for the installation of tie rods by means of robotics, was identified as potentially suitable for underwater use. It was decided to carry out the fine tuning and the evolution of the technology for a marine environment of the robot unit and of the related remote control software that controls the installation of the tie rods. An experimental test site was set up to refine the drilling, installation, grouting, monitoring and testing of underwater tie rods. The purpose was to confirm the feasibility of the proposed solution and the reliability of these tie rods for use in the reinforcement and construction of wharves. The paper also discusses the theoretical and experimental study of underwater tie rods dealing with the theoretical analysis of the interaction between tie rod and soil, aimed at identifying the correlation between the forces of applied traction and the corresponding measured elongations. A series of tests were carried out with positive results, both at the operating load of 300 kN (67 kips) and at the nominal maximum load of 630 kN (142 kips). The tests were carried out on seven tie rods, of which three were installed at a depth of 5.00 m (16 ft), principally to test the reliability of the operating and remote control systems in the presence of a significant hydrostatic pressure, and four were placed at a depth of 8.00 m (26 ft) to check the load bearing capability of the tie rods positioned at the depth called for by the current project.

Jan 1, 2011

This publication is the fourth in a series of miners? circulars covering various phases of accident prevention in bituminous-coal mines; these circulars constitute a text hook for courses of instruction on accident prevention in bituminous-coal minim. To these may be added material of particular interest in the field where the course is presented. Other circulars in the series are: Accident Statistics as an Aid to Prevention of Accidents in Bituminous-Coal Mines (Miners? Circular 47). Accidents from Falls of Roof and Coal in Bituminous-Coal Mines (Miners' Circular 48). Accidents from Hoisting and Haulage in Bituminous-Coal Mines (Miners' Circular 49).

Jan 1, 1946