Search Documents

By K. S. Mortensen

The softwall mining system is a novel, new method of mining mineral deposits in soft, shallow, nonrock ground conditions. This method can mine the ore layer without substantially disturbing the existing overburden. The softwall mining system consists of machinery that is hydraulically controlled and powered, that can be buried (or used on the surface) to extract the ore or mineral from a layered deposit. The method is essentially an application of the longwall mining concept, modified for loose overburden and ore conditions, combined with hydraulic mining.

Jan 1, 2003

By Robert E. Fosse

Driven 14-inch-square concrete piles were used as the foundations of Genentech Hall at the new University of California, San Francisco Mission Bay Campus. The five-story, steel eccentrically-braced frame building is currently under construction at a 43-acre property located in a former large shallow marshy inlet from San Francisco Bay. The piles were driven through 10 to 25 feet of fill and 20 to 60 feet of soft compressible Bay Mud into an underlying dense sand layer. Pile design capacities were developed for traditional allowable stress design, load factor and resistance design, and ultimate design criteria. The ultimate level capacities were for checks of loads occurring when the links in the eccentrically-braced frame yield during an earthquake. A load test program was performed to confirm pile design recommendations. Two test pile locations were selected for compression, tension, and lateral load tests to evaluate pile capacity and pile/soil stiffness under long-term, short-term and rapid loading conditions. Maximum test loads were 1000 kips downward, 350 kips uplift and 50 kips lateral. Foundation construction began by driving 34 indicator piles with a Delmag D46-32 diesel hammer of 113 foot-kips maximum rated energy. All indicator piles were monitored during initial driving using the Pile Driving Analyzer. Restrike data, obtained several days after initial driving, indicated significant pile-soil setup and typical pile capacity increases from 750 to 1000 kips. The majority of the 1242 production piles were then driven to acceptance criteria of 75 blows per foot and a minimum embedment of 10 feet into the dense sand bearing layer. Piles driven to full length without achieving the blowcount criteria were evaluated on a case-by-case basis. Acceptance of these piles was established by evaluating restrike data.

Jan 1, 2002

By T. W. Peglas, J. Doherty, R. A. Day

The South East Transit Project is a $520 million project in Brisbane, Australia which includes the construction of a 32 km Busway to access the south-eastern suburbs. Close to the centre of Brisbane, tunneling techniques have been used to minimise surface disruption. This paper describes some of the features of the longest driven tunnel on the project, the Vulture Street Tunnel. The Busway is a two lane expressway for buses which requires a 10.2 m finished width and a 12.6 m excavated span of driven tunnel. The Vulture Street Tunnel carries the Busway at minimal cover beneath the operating Vulture Street Railway Station, beneath a three storey office building and beneath the roadway to the Mater Hill Busway station. Halfway along the route, a Y-junction has been constructed to enable future connection with a light rail route. Key features in the design and construction of the Vulture Street Tunnel include: Use of canopy tubes to drive a 12 m wide tunnel beneath operating railway tracks with less than two metres of cover in highly weathered rock. Underpinning the office building in the route of the tunnel construction from within the building carpark. Construction of a 24 m span Y-junction with 7 metres cover of weathered and faulted rock. Use of predictive analysis as an adjunct to traditional back analysis to estimate the tunnel settlements from pressuremeter test results. This paper describes the design methodology with particular reference to settlement prediction, as well as construction innovations used to complete the tunnel. This paper will be of interest to all designers who have to create large spans in minimal cover in weak rock in urban areas and who have to predict the settlement

Jan 1, 2001

By Liyuan Chai

In this study, spent grain was used as an adsorbent for the removal of Hg(II) from aqueous solutions, the process parameters such as contact time, solution pH, adsorbent dose, and initial Hg(II) concentration were studied in batch experiments. The initial adsorption process was fast, 91.08% of adsorption occurred within 5 min and equilibrium was reached at around 30min. Adsorption process was found to follow pseudo-second-order kinetics. The equilibrium data were better fitted to Langmuir isotherm than Freundlich isotherm with the maximum adsorption capacity 41.36 mg/g. The structure and component of spent grain before and after adsorption of Hg(II) were investigated using scanning electron microscope(SEM) and energy dispersive X-ray analysis(EDAX), these analysis also confirmed the adsorption of Hg(II) onto spent grain. The results indicated that spent grain had potential as a new inexpensive adsorbent for Hg(II) removal from aqueous solutions.

Jan 1, 2009

GOLD has played a part in the development of Australia. The total yield exceeds SIX hundred million pounds sterling, while the glamour of gold-mining and the unfailing demand for the product have enhanced its influence. The production is still considerable, but the yield is less than one-quarter of that twenty years previously, while the number of men employed has dropped from 70,000 to 11,000. Not only has there been a marked decline in production, but it is anticipated that thisdecline will continue, and continue more markedly. It is therefore desirable to ascertain the causes of the decline and inquire into means for diminishing or preventing it.The problem under discussion is far from being only local. Finlay states: The grand feature of the history of the business has been the progress of an economic cycle unfavourable to gold milling. The USA yield fell from $101,000,000 to $44,000,000.South Afriea has for some time produced one-half of the world's gold; yet in the Mining and Scientific Press of 11th February, IH22, General Smuts is quoted as saying that if the premium disappeared entirely 24 out of 34 mines would shut down. The solution, however, might be either general eg, a great advance in the metallurgy of gold; or local eg, a bonus; but before discussing any of the proposed solutions it will be advantageous to review the situation.STATISTICS OF THE PAST AND PRESENT PRODUCTION OF THE WORLD AND OF AUSTRALIAThe inquirer soon finds that there is a good deal of uncertainty, and that much care is needed in collating figures. In some cases a considerable part of the output is not officially reported, and returns...

Jan 1, 1924

By C. L. Schneider, C. O. Gomes, R. P. King, J. A. Finch, D. Lin

Discussion is presented by Prof. King and Dr. Schneider of the paper by Lin, Gomez and Finch published in Trans.IMM C, vol.104, 1995, p.C155-C161. They conclude that the correction procedures used for simulated observations of simulated capped spheres are not reliable when applied to mineralogical data and that their relative ranking should not be extrapolated to other situations. Properly regularised solutions obtained with the use of appropriate kernels can be safely used for routine mineral liberation work and can be calibrated accurately against real mineralogical samples in the laboratory

Jun 19, 1905

By Frederick W. Slack

This paper will discuss the inherent value engineering associated with the design and construction of approximately 184,000 SF of anchored tieback wall, installed as part of the widening and drainage improvements for KY9 in Campbell County, Kentucky. The total project is 2.2 miles in length. The anchored walls, excavation grading and drainage total to a complete project cost of $28.4 million. This is one of the largest design-build projects undertaken by the Commonwealth of Kentucky. It also features another first for the Transportation Cabinet - the general contractor is responsible for quality control/quality assurance. The project is located just south of Cincinnati, OH and is situated along the east bank of the Licking River. The slopes along this stretch of the river have had a long history of movement and instability. The Kentucky Transportation Cabinet advertised the anchored wall portion of this project to be designed and constructed by pre-approved specialty contractors. The Transportation Cabinet provided the basic design parameters to each specialty contractor. Aspects to be discussed include the site and project history, previous attempts at slope stabilization along existing KY9, the technical proposal and bidding process, and the actual design and construction.

Jan 1, 2003

The production of sulphuric acid at Port Pirie by the contact process began in March 1924 with the commissioning of the Electrolytic Zinc Co.'s roasting and acid plant. This plant, operated by B.H.A.S. Pty. Ltd. on behalf of the E.Z. Co., continued to produce sulphuric acid from the gases evolved when roasting Broken Hill zinc concentrate in mechanically rabbled furnaces until September 1954, when the plant was closed down.In this peri9d of approximately 30 years some 600,000 mono tons of 98·5 per cent sulphuric acid was produced, most of which was used for fertilizer production at Wallaroo and Port Adelaide. During World War II 14,400 mono tons of the above was produced in the form of 20 per cent Oleum and railed to the Salisbury Munitions Factory for use in the production of nitro-glycerine, gun-cotton and T.N.T.In the early post-war period various ways of converting at least some of the sulphur in the gases' discharged to atmosphere from the lead sintering plant were considered until, in 1949, it was decided to erect a modern contact acid plant. Much work remained to be done on the roasting plant to produce a gas of suitable grade for the contact process and also on the design of a purification section suitable for the treatment of D.L. gases.The acid section itself, however, was largely of conventional design and it was therefore decided that this would be erected first. To it was then attached a sulphur-burning section to allow it to operate as a "hot gas" brimstone acid plant until the roasting and gas purification plants had been designed and erected. In this way the urgent need for sulphuric acid in the fertilizer industry would be relieved, to some extent at least, as soon as, possible.

Jan 1, 1956

By William E. Lardner

Interlocking caisson walls developed from conventional "soldier pile and lagging" shoring. In the latter, the soldier piles receive directly most of the soil load. Natural arches form in the soil behind the shoring; the lagging supports little more than the segment of soil inside the arch. Fig. 1: A typical layout of a lagged wall [ ] Fig. 2: A typical layout of an interlocking caisson wall [ ]

Jan 1, 1987

By P. C. Holloway

La Oroya zinc ferrite (19.5% Zn, 26.6% Fe, 0.052% Ga, 0.075% In) was roasted with coal under conditions more oxidizing than normally used in a Waelz kiln, and the roasted residues were leached with 200 g/L H2SO4. Overall zinc recoveries of up to 97% were achieved, with 35% of the zinc reporting to the fume after roasting at 1,100°C with a bituminous coal addition of 20%. Under these conditions, 93.2% of the Cd, 13.4% of the Cu, 33% of the Ga, 61% of the In and 18.2% of the Pb were recovered either in the fume or in the leach solution. At 2006 metal prices, the value of the recovered metals is comparable to that obtained from commercial Waelz kiln processing of this residue. Zinc in the franklinite (ZnFe2O4) mineral is reduced to zinc vapor, and, after oxidation, some of the zinc is found as ZnO or as Zn2SiO4 in the roasted residue. Iron reacts to form either hematite (Fe2O3) or magnetite (Fe3O4), with no metallic iron detected in the roasted residue, and less than 2% of the iron is solubilized during leaching. The residue produced after roasting and leaching is, therefore, much more stable than the residue from Waelz kiln processing and should be suitable for disposal in a landfill.

Jan 1, 2008

By H. F. Yancey

About 65 percent of the more than 400 million tons of coal produced annually in the United States is mechanically cleaned to remove the inorganic impurities before being sent to market. The impurities, principally shale and clay with some pyrite, average about 20 percent of the raw coal treated. Nearly 95 percent of the tonnage is treated by wet processes, in which water, suspensions of solids in water, or occasionally calcium chloride solutions are employed. Difference in density of coal and impurity is the basis of these processes. Of major importance in the separation is the competency of the impurities, that is, the resistance of the impurities to size disintegration in water. In general, the impurities are more resistant in geologically older coals or those in effect made older by metamorphism. If the impurities suffer reduction in particle size when immersed in water, the separation of organic from inorganic material becomes more difficult, Recently the Scientific Department of the National Goal Board (Great Britain) undertook fundamental research into the interaction of shale and water and also developed an empirical method of assessing shale breakdown or disintegration. 6

Jan 1, 1962

By Davorin Kolic, Harald Wagner

Conventional ground support in accordance with latest state-of-the-art considers proper preparation of geotechnical investigation, structural design, observation during construction and fair risk sharing documents. Depending on the ground, there are different means and methods, reflecting different experiences. The paper is presenting ground support concepts, as mostly used in Europe during the past three decades. It discusses the use of anchors as well as the use of steel arches respectively combinations. It also discusses different applications of plain shotcrete, respectively fibre reinforced shotcrete. As excavation sequence is a major input to create the ground arch, the paper discusses also criteria to create closed ring conditions. Finally deformation criteria will be presented with case histories in order to control stability of the structure.

Jan 1, 2001

By Sahoo K. C

Traditionally, the blast furnace (BF) has maintained a dominant position as the primary source of iron units. Notwithstanding the efficient nature of the process in respect of its material and energy consumption, the conventional blast furnace route is faced with limitations such as stringent quality metallurgical coke, high capital investment, etc. While BF will continue to retain its predominant position as the foremost ironmaking technology, the alternate processes may also have a role to play. Direct Reduced Iron (DRI) or sponge iron industry is all set to take a firm root in India as one important solution to the problems of shortage of metallurgical coal and ferrous scrap and high investment costs faced by the country's steel industry. The commercial proven DR processes coupled with electric arc furnace (EAF) steelmaking have also offered a viable alternative to the blast furnace - basic oxygen furnace (BF - BOF) route for the installation of integrated plants under specific local conditions. The performance and efficiency of DRI processes mainly depend upon the chemical and physical behaviour of the raw materials especially the iron bearing materials. Iron oxide pellet and sized lump ore constitute the oxide feed stock, while pellets form an ideal feed stock for direct reduction, use of lump ore is economically advantageous because of its lower price. National Mineral Development Corporation Limited (NMDC), being one of the major producer of iron ore in the country since last four decades, has established technology and developed process flowsheets for production of suitable calibrated lump ore for DRI production, besides supplying the natural lump ore for conventional blast furnace requirements. In addition to the above, extensive pilot plant tests have been carried out at the R&D Centre of NMDC for preparation of iron ore concentrates suitable both for direct reduction and blast furnace grade pellet feed using the iron ore fines from its own mines and as well as from the other iron ore mines in the country. For utilisation of the huge quantity of slimes generated in its ore processing plants, NMDC has planned to set up the first commercial plant adopting the smelt reduction process (ROMELT Process) for production of pig iron from Bailadila slimes. The paper mainly deals with various beneficiation techniques adopted for production of DRBF grade pellet feed from iron ore fines. Also presented in the paper, the extensive work carried out at R&D Centre on preparation and evaluation of calibrated lump ore (Natural Pellets), based on which, suitable modifications are incorporated in the ore processing plants of NMDC for production and supply of the same to sponge iron industries.

Jan 1, 1999

By Allison

During the 1980’s, laboratories opened throughout the United States to serve the analysis needs of a rapidly growing asbestos abatement industry. The samples analyzed were either collected during the abatement of known asbestos-containing materials or were suspect asbestos-containing construction materials. Many asbestos analysts received minimal training and used analytical protocols that were industry specific. False positives (reporting a sample as containing asbestos when none is present) went unnoticed or had minor repercussions. The mindset of the industry was to err on the conservative side – it would be better to identify a non-asbestos fiber as asbestos than visa versa. With growing public awareness of the health hazards of asbestos, other materials began to be tested for asbestos content. Rock and ores began to be tested for naturally occurring asbestos by these laboratories using the same protocols or an in-house protocol. Analysts were given no additional training and accreditation, in most cases, it was not required. With no consistency in sample collection, testing protocol or expertise in analysis, significant discrepancies in final results can be expected. If we further complicate this scenario with misidentification of naturally occurring look-a-likes for asbestos, expensive false positives are likely. To avoid the repercussions of misidentification of naturally occurring chrysotile asbestos from look-a-like fibers in rock and ores, correct sampling and analysis protocols with more stringent scientific diagnostic criteria are needed.

Jan 1, 2005

CrusherMapperTM - A New Tool for Crusher Condition Monitoring The efficiency of mineral processing plants is entirely dependent on the availability of the plant equipment critical path. This typically concerns comminution circuits consisting of primary crushers and primary grinding mills. Crusher and mill availability are determined by the frequency and duration of maintenance shutdowns, which are primarily driven by the need for replacement of sacrificial liners. The change of crusher and mill liner shape over respective life cycles also strongly affects plant efficiency. It is therefore highly desirable to accurately monitor the condition of mills and crushers in order to optimise plant efficiency through maximised availability and targeted liner shape. Traditional comminution liner and other production parameter condition monitoring has been attempted through ineffective methods which prevent satisfactory management of crusher and mill maintenance and reduce operational control. This situation has recently dramatically improved for grinding mills through the development and commercial deployment of MillMapperÖ, a technology based on three-dimensional laser scanning data and dedicated software (Franke, Lichti and Stewart, 2006; Franke and Lichti, 2007; 2008; Franke, 2008; Franke, Redman, Johnson and Michalek, 2009). At the time of writing in late 2009, MillMapperÖ is in successful use at a rate of approximately 170 surveys and associated reports per annum at processing plants in Australasia, South America, North America and Africa. This paper presents the introduction of CrusherMapperÖ, the MillMapperÖ equivalent for crushers. CrusherMapperÖ also utilises high density, high accuracy laser scanning data, and features dedicated algorithms for three-dimensional monitoring of wear on crusher concaves and mantles. This facilitates the detection of wear hot spots or zones or localised liner failures, and accurate forecasting of reline tonnages and dates. It also for the first time provides the means to establish optimised concave and mantle shapes in order to achieve production targets. In contrast to any other currently utilised condition monitoring method, CrusherMapperÖ data collection can occur remotely and does not require any shutdown or crusher isolation. This method therefore does not interrupt crusher production while at the same time eliminating any confined space risk normally associated with taking measurements inside the crusher cavity.

Sep 13, 2010

The methods and equipment developed and used at the Mount Isa mine to obtain samples of uncemented hydraulic fill lying above major horizontal pillars are described. From existing underground development, samples were obtained at distances up to 50 m, of which up to 30 m was through hard rock. Samples were used to predict fill behaviour as it affected mining security during recovery of the pillars.Specialized equipment for difficult sampling situations and also other sampling exercises are described.

Jan 1, 1976

By Tom A. Armour

Different variations of soil nailing techniques have been used in the United States since the late 1970's. Such techniques owe their origins to French developments, which began in the early 1970's as a spin-off from European tunneling excavation support practice. The growing demands of urban infrastructure development and rehabilitation and environmental protection have created an active and expanding soil nailing market demand for earth retention and slope stabilization in the United States since its early developmental years. There is a clear need for a fundamental review of the large number of soil nailing techniques that are currently being used in the United States. Following a brief summary tracing the historical development of soil nailing and a generic classification of applications, this paper provides a review of the different recent advances in the design and construction of soil nailed systems. Discussion topics include nail design advances, permanent "top-down", structure support/underpinning, alternative face stability measures, composite systems, hollow bar and fiberglass nails and architectural reinforced concrete/shotcrete facings. Case histories will be presented to illustrate each of these advances.

Jan 1, 2003

By F. W. Jessen, C. C. Patton

Adsorbed films were formed on polished stainless steel specimens from dilute benzene solutions of two crude oil distillation residua. Although the two residua were extremely dissimilar in composition, contact angle measurements showed that the two films increased the wettability of the steel specimens to oil by equal amounts. Furthermore, the wettability of the films was essentially unaffected by the desorption techniques used. Paraffin deposits were formed from heptane-wax solutions on the same stainless steel specimens. These deposits definitely adhered to the surface. Presence of an adsorbed crude oil film on the metal surface increased its free surface energy and resulted in increased deposition of paraffin. The addition to the heptane - wax solution of small amounts of the same distillation residua that were used to form the adsorbed films resulted in decreased cohesive strength in the deposits formed, which resulted in decreased deposition. The presence of a crude oil fraction both in the solution and as a preadsorbed film eliminated the adherence of a deposit of any kind. A mechanism of deposition is proposed which explains the results obtained. INTRODUCTION The natural formation of any predominantly organic accumulation in oilwell tubing, surface flow lines or other production and storage facilities is called a paraffin deposit. These deposits restrict the production of crude oil, causing a substantial increase in production costs because of decreased flow capacity, expense for periodic deposit removal and unproductive downtime. The conditions under which such deposits form, their physical characteristics and the nature and severity of the problem created are extremely varied. Over the past several years, much progress has been made in developing and utilizing methods to remove accumulated paraffin deposition. However, like so many other problems, the basic stumbling block appears to be a lack of understanding of the fundamental mechanism involved in the formation of such deposits. Crude petroleum is known to contain considerable quantities of polar, surface active substances which Doddl has shown to be present at the oil-water interface. Denekas, Mattax and Davis2 observed that the wettability of reservoir rocks was drastically altered by exposure to crude oil fractions; and Zisman, et a1.3 showed that the nature of the compounds adsorbed on a surface would determine its wettability characteristics. Cole and Jessen4 and Ehrig5showed that surface wettability can have a profound effect on the magnitude of paraffin deposition, and Parks6 demonstrated chat the presence of certain adsorbed films on a metal surface would reduce the adherence of paraffin to that surface. Zisman7 has since advanced the theory that the conditions for adhesion are the same as for wetting. Therefore, it was felt that there was adequate evidence to support the supposition that adsorption of compounds from a crude oil might play an important part in paraffin deposition. ADSORPTION-WETTABILITY EXPERIMENTS Initial experiments were conducted to determine the effects of adsorption from solution of crude oil residua on the wettability of a polished stainless steel surface. Distillation residua with initial atmospheric boiling points of 700F were used in preference to the whole crudes in order to concentrate on the molecular weight range of interest, and to eliminate the possibility of composition change due to evaporation of the light ends. Also, these high boiling materials would be expected to be adsorbed from the whole oil in preference to similar compounds of lower molecular weight.

Jan 1, 1966

By C M. Wawryk, S L. Garwin, J D. Foden

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Batu Hijau porphyry Cu-Au deposit in south-western Sumbawa, Indonesia is an ideal natural laboratory to study the fractionation of iron isotopes in magmatic rocks that range in composition from basaltic andesite to tonalite. Intrusive rocks are associated with a porphyry system that contains well-preserved early hypogene copper mineralisation. We analysed pre-, syn- and post-mineralisation igneous intrusive rocks. We also separated magnetite, chalcopyrite and bornite from hypogene porphyry-style quartz veins, and measured the Fe-isotope ratios of samples by solution multi-collector ICP-MS. Iron isotopic composition of samples from the magmatic suite show an increasing d57Fe with increasing SiO2, supporting geochemical and textural evidence that the Batu Hijau Tonalites underwent closed system fractionation. Equilibrium and co-existing mineral textures allow the calculation of the following preliminary empirical mineral-mineral fractionation factors at 500°C for certain mineral pairs.Iron isotopes have the potential to provide geothermometric data to complement fluid inclusion data, especially where heating stages have operational limitations and where fluid boiling results in a wide variety of inclusion types that may make analysis difficult.CITATION:Wawryk, C M, Foden, J D and Garwin, S L, 2015. Iron isotope fractionation in magmatic-hydrothermal minerals – a porphyry copper case study from the Batu Hijau deposit, Sumbawa, Indonesia, in Proceedings PACRIM 2015 Congress, pp 389–396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By T. O. Hagan

Analyses of accident records show that a better understanding of very basic strata control principles and practices, by production personnel, will improve worker safety. Workers, lack of knowledge, with respect to aspects of strata control, increases their exposure to such strata control risks. The primary objective of the Safety in Mines Research Advisory Committee (SIMRAC) project 02 02 07 was to develop tools for the transfer of strata control knowledge. Four such tools were developed, three of which focused on illiterate underground mine team members who are not yet able to take advantage of the Mining Qualifications Authority (MQA) learning process (see project outcomes 2, 3 and 4 below). The tools were designed to equip these workers with sufficient knowledge and ability to work safely underground until such time as they can take advantage of the MQA system. Project outcomes: 1 A four-minute video using animation to illustrate the causes and prevention of falls of roof in South African collieries. 2 Software to demonstrate the capability of reconstructing, interactively, accident scenes and actions that have taken place underground in stopes. 3 A strata control bridging course for illiterate mine team workers. 4 Small-scale wooden models that will be used to design life-size mock-up facilities to assist with the above mentioned bridging course. 5 Workshops and presentations to demonstrate the outcomes 1to 4 above.

Jan 1, 2005