Search Documents

Close spatial relationships between the deposits of the Etheridge Goldfield (23 000 kg of bullion) and various regional geological and geophysical features suggest that genesis of the ore deposits was a multi-stage process that started with magmatic and metamorphic stages in the mid-Proterozoic, climaxed with structural and hydrothermal stages in the late Palaeozoic and terminated with an oxidation enrichment stage in the Cainozoic.This hypothesis permits classification of the Georgetown region into areas likely to contain deposits of the Etheridge type and those unlikely to do so; it is concluded that there is little scope for the discovery of extensions of this field.However, the stratigraphic interval between the postulated source rocks of the Etheridge field and stratigraphically higher host rocks of the Croydon field may contain disseminated replacement gold deposits of the Carlin type. The potential host (Pyritic carbonaceous, and locally dolomitic siltstone of the Candlow Formation) is locally faulted and cut by granitoids and the extension of a mineralised, long-standing zone of structural weakness.

Jan 1, 1981

By Changqing Su

A batch incubation experiment has been carried out to investigate the optimal condition for the microbial remediation of hexavalent chromium (Cr(VI)) in soils contaminated by chromate ore processing residue at Hunan Iron-Alloy Factory in China. The optimal condition was obtained by comparing the remediation efficiency of Cr (VI) by indigenous bacteria under different culture media, the quantity of nutrient sources, the pH and the temperature. The results indicated that glucose and yeast extract was the optimal component of culture medium and the quantities of the above components were 8 g L-1 and 13 g L-1, respectively. The optimal temperature and pH value were 30_ and 10.0, respectively. A bioreactor was operated under the optimal condition to evaluate the efficiency of Cr(VI) remediation in the contaminated soil. The result showed that water soluble Cr(VI) in soils was reduced from 320 mg kg-1 Cr(VI) of the initial concentration to below detection limit after 30 h in a bioreactor. Thus, there is a large potential to make bioremediation for the reduction of Cr(VI) to Cr(III) by the addition of optimal culture medium under aerobic condition.

Jan 1, 2010

By Robert B. Parsons

"Exploration and development of mineral resources in developing countries by Canadian-based multinational mining companies is becoming increasingly common. One problem being encountered is that the objectives of the governments of developing countries can differ from those of developed countries. These objectives are not always consistent with maximizing returns from the projects, which can create conflicts between the mining company's responsibility to its shareholders and the desire to be a good corporate citizen. This article discusses how a mining tax regime can be designed to make the social goals of a government consistent with the economic goals of the company.IntroductionAt the recent International Seminar on Mining Taxation organized by CIM and the United Nations there was considerable discussion about the role of international mining companies operating in developing countries. Not surprisingly, given the diversity of backgrounds of individuals attending the Seminar, there were different opinions about what this role should be.Government PositionRepresentatives of governments pointed out the strong desires of their countries for technology, high-level technical training of their workforce, increased employment, and development of social infrastructure. They pointed out that, to a large extent, these objectives could be more efficiently met by mining companies operating in the country than by the governments themselves. For example, a multinational mining company (""MMC"") would have extensive knowledge of the various technologies available, and would have performed a detailed evaluation of the mineral resources before choosing the most cost-efficient technology for that project. They would, therefore be in an ideal position to assist the country in importing and developing such technology. Similarly, the company could provide opportunities for hands-on training, both at the technical and managerial levels, which would otherwise be unavailable to the government."

Jan 1, 1991

By Yajie Wang

Traditionally, roof falls are usually attributed to bad roof strata and high vertical stress related to the overburden depth. However, roof falls under shallow overburden depth are oflen caused by a high horizontal stress field. Recent studies have proven that the high horizontal stress field, if existing, plays a major role in roof stability. Also the roof conditions are related to the entry diredions under a horizontal stress field. Questions are: How to orient the entry to a favorable direction to prevent the roof falls? If the entry cannot be oriented, how to support it? Through a case study in mine A, this paper analyzes the horizontal stress effect on roof stability. The guideline for the entry orientation is given based on the results of analysis. Additionally, suggestions are made for those entries that cannot be oriented to a favorable direction.

Jan 1, 1998

By Brian W. Stump, David P. Anderson, John Wiegand

Mining explosions are designed for a variety of purposes including the fragmentation and movement of materials. The blast design is dependent on the particular application intended and the material properties of the rock. The range of mining applications from hard rock quarrying to coal exposure to mineral recovery leads to a great variety of blasting practices.

Jan 1, 1997

By Frank Hirthammer

Productivity, customer relations, and effectiveness of work depend to an ever-increasing extent on a functioning logistics system tailored to the needs of the user. Of course, it is not possible to cover and explain all aspects of the logistical requirements of even a small part of an industry, in a single article. The article speaks specifically about the particularities and differences in the logistical requirements in the explosives sector. Starting with questions of safety, handling and quality up to the legal basis, there are special requirements regarding the logistics in the explosives sector. The results of innovative logistics solutions are presented using three examples from daily work practice.

Jan 1, 2019

By A. Drouin, D. Lemieux, C. Chouinard

"A gold bearing pyrite concentrate was treated at the demonstration scale (15 t/d) for the extraction of gold using a cyanide-free process. The pyrite was depressed in the flotation circuit in order to promote the flotation of copper and to achieve a sufficient copper grade to meet the copper smelter criteria. However, the recoveries of copper were 80% and only about 50% for the gold was found in the copper concentrate. The balance of the gold (50%) and copper (20%) contained in the pyrite concentrate as a reject from an overall flotation circuit. The gold grade in the pyrite concentrate is 5.40 g Au/t and copper about 0.77%. About 170 tons of pyrite concentrate were processed in the DST demonstration plant. The concentrate was first oxidized using a fluid bed to produce a calcine. Copper was then extracted as copper sulphate using diluted sulphuric acid. The residual solid was submitted to the DST chlorination process for gold extraction. Thereafter, the gold was recovered from the pregnant brine by precipitation over silica using DST proprietary process. The maximum gold recovery by chlorination was 90%. The average gold recovery by cyanidation of these calcines was 71%.IntroductionDundee Sustainable Technologies (“DST”) has developed a chlorination process as an alternative to the conventional cyanidation process for the extraction of precious metals from ores or concentrates. The technology offers viable and efficient gold recoveries and the ability to handle refractory ores and contaminated material (As, Hg, etc..). The process was successfully demonstrated on hundreds of samples provided by various mines, exploration and development projects and has evolved from laboratory experiment to demonstration at an industrial scale.DST’s chlorination process operates in a closed loop circuit, which implies that no liquid effluents are generated. The chemistry and process design allows precious metal deposits containing base metals to be treated viably. The tailings from the process are inert and non-toxic, sulphide depleted and thus non-acid generating. The efficiency of the process has demonstrated excellent gold recoveries within a fraction of the time needed for cyanidation to obtain similar results. The company completed in 2015 the construction of the first industrial demonstration plant operating with the DST technology. The plant has a capacity of 15 tons per day of mineral concentrate, and the ability to extract gold and silver utilizing DST chlorination technology.DST has tested its chlorination technology at demonstration scale on the refractory pyrite concentrate containing 5.40 g Au/t and 0.8 %copper. This auriferous pyrite concentrate, was by-product of copper concentrate respecting the copper smelter norms, is produced in a country where cyanide is prohibited and refractory to cyanidation. The pyrite concentrate was initially processed successfully (gold recoveries: > 90%) by the DST technology at laboratory (2011: 20 kg) and pilot (2014: 5 tons) scales to extract gold. About 170 tons of this pyrite concentrate were processed in the DST demonstration plant located in Thetford Mines."

Jan 1, 2017

The Northland region of New Zealand has a complex geological history which has long been the subject of considerable controversy. Small mineral deposits have been discovered in the past, and some have been mined. Except for aggregates and very high quality china clay, mining is virtually nonexistent at present. Mercury mining is proposed from small deposits in the Kaeo area. Intensive exploration for epithermal precious metals deposits in the past seven years, combined with some recent geological mapping undertaken by the Geological Survey and University thesis students has added greatly to an understanding of Northland's geology. Mapping of the Whangaroa-Kaikohe map sheet at a scale of 1:100 000 by Brown and Laurenson Limited has enabled new geological information to be collated for the first time since 1961, when the last geological map was published. The 'Northland Allochthon' is now observed to be a series of four or more thrust sheets each containing predictable formations. High angle faulting contemporaneous with overthrusting has modified the thrust sheets, and established a series of horsts and grabens. The Pirau Fault is considered to be a major earth fracture.

Jan 1, 1987

By A. W. Ruff

The seismic wave produced by an explosive is very important in blasting. A true understanding of the wave is only important when considering possible structural damage to buildings located near the blast, but it is also of primary importance when considering rock fragmentation. Because of the importance of the seismic wave to fragmentation, a finda-mental study of the seismic wave and its effect was made at the Cananea Consolidated Copper Co.'s mine at Cananea, Sonora, Mexico. Strain gages were used to measure the strain in the rock when nearby explosive charges were detonated. The variance in the circuit voltage caused by changes in the resistance of the strain gage was measured with an oscilloscope and recorded with a Polaroid camera. CONFINED DRILLHOLE CHARGES To record the seismic wave from a confined drillhole explosive charge, a gage was cemented to the bottom of a 4-in diam drillhole. The horizontal gage hole and nine horizontal charge holes were drilled perpendicular to the center line of the 2-39 drift and 4 ft above the floor. The gage hole was 29 in. deep, and the charge holes were drilled so that each bottomed 1 in. deeper than the gage hole. The gage was installed with its axis horizontal and parallel to the 2-39 drift. The charge holes had the following horizontal distances from the gage: hole 3, 3 ft; hole 4, 4 ft; hole 5, 5 ft; hole 9, 9 ft; hole 10, 10 ft; hole 14, 14 ft; and hole 15, 15 ft. Figs. 1 and 2 show the relationships of the gage and the charge holes. Charges of 80 pct special gelatin, which weighed 50, 100, and 150 g were exploded in the charge holes and the seismic waves were recorded. All charges were stemmed with 200 g of mud and detonated with an electric blasting cap. Fig. 3 shows the recorded seismic waves. The reflected components of the waves were too weak to be objectional on these records. Table I shows the data taken from the wave forms. The approximate average velocity of a wave with a 9-ft travel distance was 12,900 fps. Since different charge weights were used, it was necessary to scale the data. The scaled maximum compress ion-strain data and the scaled maximum tens ion-strain data are shown in Figs. 4 and 5, respectively. Figs. 6 and 7 show the strain-distance data from Figs. 4 and 5 converted to a 1-lb charge. The results showed that the wave consisted of an initial compression pulse followed by a tension pulse. The amplitude of the tension pulse approached the amplitude of the compression pulse as the distance between the gage and the shot increased. The decay rate of the seismic wave is very important in the evaluation of the blasting characteristics of a rock. When high-amplitude stresses are produced, as in rock fragmentation, the rate of decay is much more rapid than when small amplitude stresses are produced. In underground mine blasting, the burdens are usually not greater than 6 ft and the decay is very rapid. The rapid seismic-wave decay rate in the fragmentation range means that in practice, if the minimum weight of powder is used to break a specified burden, only a very

Jan 1, 1961

By Roy A. Imbsen

Following the 1989 Loma Prieta earthquake, California Department of Transportation (Caltrans) expedited an effort to evaluate and retrofit important state-owned toll bridges to en­hance performance of the state's transportation systems during and after major (credible) earthquake events. Imbsen and Associates, Inc. (IAI) along with their sub-consultants, were awarded a contract to conduct seismic evaluation and to develop retrofit design for Benicia-Martinez Toll structure, to meet a "Serviceable" performance requirement after the event of a "Safety Evaluation Earthquake." This paper describes the design and construction specifications for the deep foundations supporting the main spans of the Benicia-Martinez Bridge. Benicia-Martinez Toll Structure (George Miller Bridge), a high-level deck-type welded truss bridge with welded girder approach spans, carries Interstate Route I-680 over the easterly end of Carquinez Strait near San Francisco, CA. The nearly 5000 ft long main truss structure consists of ten spans, ranging from 330' to 528' in length, supported on cellular reinforced con­crete pier structures. Foundation systems across the waterway, consist of cellular reinforced concrete footings, supported by groups of 6' diameter, concrete filled, steel caissons, resting on 5' deep rock sockets, at depths of 50' to 150' below the water level. Seismic evaluation of the existing foundation systems accounted for spatially varying ground motion along the length of the structure, variability of foundation material strength (i.e. at bed-rock), variation and effects of scour depth on the performance of the foundations, and dy­namic soil-structure interaction. Performance of caissons beyond their elastic strength, as well as their effects on the behavior of the foundations and substructures were evaluated and considered in establishing foundation vulnerabilities. Several retrofit strategies were considered leading to a final retrofit strategy to strengthen end connections of existing caissons, as well addition of new caissons to provide adequate lateral force resistance for the foundations. Final design package includes specifications as well as construction methods and requirements for existing and new caissons, under traffic, and pile load testing procedures for design loads of up to 12500 kips per caisson.

Jan 1, 1998

By O. Nyandoro, K. Khoza-Shangase, M. Madahana, N. Moroe

"Occupational noise-induced hearing loss (ONIHL) is classified as the leading work-related disability in the mining industry. ONIHL has a negative impact, on not only the health and occupational productivity of affected individuals, but arguably also on the country’s mining industry and economy. Hearing conservation programmes (HCPs) are an effective strategy in the management of ONIHL. However, current literature indicates that HCPs are not achieving the anticipated and desired outcomes in the South African mining sector despite the efforts focused on the management of ONIHL. Therefore, the purpose of this study is to propose the use of a feedback-based noise monitoring model as a tool for monitoring and managing ONIHL in the South Africa’s mining sector. This model is a basic static feedback model with practical applications such as estimating, monitoring. and providing quantitative information to aid miners, mining administrators, and policy-makers in decision-making around HCPs. Additionally, the model could form part of an early intervention and management strategy for ONIHL in the workplace. The strength of this model, although currently static, is that it encompasses all the pillars of HCPs and takes into account the policies concerned with the management of ONIHL in the mining sector. IntroductionHazardous noise levels (above 85 dBA) in the workplace place exposed employees at risk of developing a disabling occupational noise-induced hearing loss (ONIHL). ONIHL is the ‘partial or complete hearing loss in one or both ears as a result of one’s employment’ (Nandi and Dhatrak, 2008, p. 1). This type of hearing loss develops gradually as a result of being exposed to continuous or intermittent high levels of noise over a long period of time (McBride, 2004; Patel et al., 2010; Rappaport and Provencal, 2001). A hearing threshold below 40 dBs is classified as a disabling hearing loss (Yadav et al., 2015), resulting in a hidden condition that does not readily manifest itself (Tye-Murray, 2009, p. 3). Dugan (2003) describes disabling hearing loss as the ‘most prevalent, least recognized and least understood physical disability’, while Copley and Frederichs (2010) and Hermanus (2007) argue that permanent disabling hearing loss is a major contributor to the global burden of disease on individuals, families, communities, and countries."

Jul 1, 2019

By R. L. Andrew

The southwest Pacific has produced at least four of the world’s premier porphyry copper-gold deposits, and the current level of exploration is likely to produce even more. An appreciable amount of gold is being produced with this copper, with obvious economic advantages. Gold content, in addition to their large size, makes the southwest Pacific’s porphyrycopper-gold deposits very attractive exploration targets. The recognition of telescoping and overprinting of porphyry systems has produced a greater awareness of the likely surface expressions, in particular the significance of advanced argillic lithocaps in porphyry exploration. The recognition of the spatial and genetic association of porphyry copper and epithermal gold systems (Sillitoe, 1972), as in other parts of the world, has had important implications for exploration in the Asia Pacific region.

Jan 1, 1995

By . Jaime G Tapia Aguirre

La Unidad Minera Rosaura del Grupo Glencore fue considerada la mina subterránea más segura del país durante los años 2005, 2006 y 2007. Sin embargo, cuando el Grupo Glencore adquirió la concesión de Rosaura, el panorama minero era de una mina marginal, de bajas leyes. Por esta razón, el único metodo a ejecutar para hacer de Rosaura una mina rentable era el de utilizar un método masivo. Em ese semtido, el presente texto señala la operación de mina cone el análisis y conocimiento de causa raíz en la prevención de caída de roca.

Sep 12, 2011

By E. Northcott, I. M. LeBaron

Before describing the electrostatic processing of feldspar, it might be well to review some of the basic definitions and terminology of feldspars. The feldspar minerals constitute a group of alumino-silicates of potassium, sodium, and calcium. Barium feldspar sometimes occurs naturally but is very rare. Hardness varies between 6 and 6.5 and specific gravity between 2.5 and 2.8. Color is generally white or pale shades of red, yellow, or green. The approximate chemical composition of the principal feldspars is given in Table I. The albite (sodium aluminum silicate) and an-

Jan 1, 1959

By K. Morsi

The interest in spark plasma sintering has been growing considerable over the past few years. This has been brought about by the unique advantages of the process, which include reduced sintering temperatures and times and the production of materials with unique microstructures and properties. Despite its current reputation as an outstanding process that has solved major problems such as nano-powder consolidation, it has so far been largely limited to the manufacture of simple shapes, due to its inherent geometric configuration. In this paper we present preliminary results on spark plasma "extrusion" that can allow the production of extended geometries via electric-current processing. Preliminary results on the processing and microstructure of spark plasma extruded aluminum are discussed.

Jan 1, 2009

By G. Styles, K. Lye, R. Tenbergen, M. Mayhew

Requirements to produce a higher bulk concentrate grade have necessitated extensive use of on-stream analyser data and computer programming to obtain the targets set for Frood Stobie Mill as required by overall milling considerations.A brief history of milling process changes associated with the changes from a low grade (3% Ni) bulk concentrate in the sixties to a high (6 to 8.5%). Nil bulk concentrate currently will be presented.The heart of the presentation will be the computer control schemes for ""self optimisation"" of the distinct flotation sections in the plant within certain restraints to achieve targets set by the mill metallurgist.

Jan 1, 1985

By Kevin M. Connor, Malcolm J. McPhersqn

Examples are presented in which Time Domain Reflectometry (TDR) was employed to locate deformation of rock masses induced by mining. The first example involved motoring the propagation of overburden fractures above a longwall coal panel and the second example involved the we of a)R to monitor rock mass deformation in the vicinity of a strip mine highwall. Bock mass deformation, strata separation and large block movement generated strains and failure along coaxial cables which were installed in drill holes and the TDR reflections generated by these strains and failures were monitored. Analysis of field data and a preliminary laboratory test indicate that it may be possible not only to locate rock mass movements but also to quantify these movements with TDR data.

Jan 1, 1984

By António Fiúza, Anthony Danko, Patrícia Leitão, Aurora Futuro, Cristina Vila, Lurdes Dinis

The average global recovery rates for processing scheelite ores by physical methods are normally in the range 50 to 70%, and it is problematic to attain a minimum grade of 60% WO3 in the concentrates without penalizing further this yield. Direct hydrometallurgical processing of low-grade concentrates or medium- to high-grade ores may become an interesting global economic alternative as it allows increasing the recovery rate, avoiding major penalizations due to the grade of the concentrate and increasing the added value of the final product. Leaching of scheelite by sodium carbonate presents several advantages such as its selectivity regarding the dissolution of troubling metals like iron and aluminium, allowing for a simple and flexible process diagram. However, it has the disadvantage that it is performed at high temperature and pressure with a high consumption of reagents. The feasibility of leaching is appraised by the extraction yield and selectivity, but also by the operating cost. Considering these aspects, a relevant objective of the research was to transform alkaline pressure leaching into a feasible processing alternative directly applicable to both medium- and high-grade ores and simultaneously to low- and high-grade concentrates produced by physical methods. The research used ore samples and low-grade concentrates from a typical skarn orebody as well as high-grade concentrates from a chalcopyrite-scheelite orebody. Different operating conditions were tested. Temperature, pressure and reagent concentration showed to be fundamental, but not exclusive, in determining the leaching behaviour. The operating conditions are milder than the ones generally proposed in the literature or currently in use in industry, but with higher carbonate consumptions. The research was oriented towards potential industrial implementation allowing for the application of optimization methods and straight scale-up to pilot-plan design and project.

By J. E. Lawver, B. J. Clingan, R. E. Snow

Response surface methodology is a well-known and powerful technique for determining optimum conditions in flotation systems. One disadvantage is the onerous task of the numerical calculations and curve plotting. This paper describes a system in which the investigator simply selects the range of several flotation variables after which the design of the experiment, data analysis, generation of response surface equations, and response surface plots are automatically carried out using a digital computer and a computer-driven curve plotter. Several typical response surfaces of important variables in phosphate flotation are presented as examples.

Jan 1, 1980

By Hannan J. C

In New South Wales, development applications for major coal mining proposals are determined by the Minister for Planning and Environment and applications for mining leases and other mineral titles are dealt with by the Minister for Mineral Resources. The environmental conditions placed on the development consent, the coal mining lease and the approvals and licences under the pollution control legislation, amount to a substantial component of any new project's planning and commissioning considerations.An outline is presented of the framework within which various approvals are granted and conditions for environmental management are imposed upon mining projects. The principles and concerns, as perceived by the regulatory authorities, on which the majority of approval conditions are based are also outlined.No attempt has been made to analyse the extent to which these principles or standards are achieved in practice, nor to discuss the degree to which some of the conditions are achievable with the current status of technology and economics in the coal industry.

Jan 1, 1987