Search Documents

The U.S. Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By John H. Johnson

Diesel tailpipe CO, C02, NO, and N02 concentrations by the Emissions Measurement Apparatus (EMA) were found to compare satisfactorily with simultaneous concentrations by instruments in the MSHA engine certification laboratory in Bruceton, Pa. The EMA was then applied to the measurement of LHD vehicle diesel tailpipe gases and smoke opacity in the White Pine and Brushy Creek Mines. A general experimental approach was developed by which instruments could be compared for the measurement of diesel exhaust pollutant concentrations in the 1/2 to 5TLV range. The concentrations are changed by varying engine speed, dynamometer load, and the portion of the exhaust which enters the dilution tunnel. Dräger detector tube diluted exhaust CO, CO2, NO, and NO2 measurements were compared with simultaneously taken portable instrument measurements. Diesel exhaust interference inaccuracies were separated from inaccuracies due to detector tube calibration by comparing the instrument readings with both actual detector tube readings and detector tube readings corrected by recalibration of the detector tubes alongside NBS traceable calibration gases. The detector tubes' accuracy was found to be only slightly affected by diesel exhaust interferences and it was concluded that most measure within certification limits established by the National Institute for Occupational Safety and Health. The effects of 2 exhaust system configurations on the pollutant concentrations in a dead-end heading were studied. Both of the configurations exhausted the gases near the roof, directing them toward the crosscut, and both improved the stratification of the air in the heading, due to the bouyancy of the hot exhaust gases. One of the configurations was a pair of Fume Diluters which diluted the exhaust with air by a 10:1 ratio, and the second system was simply a pair of exhaust pipes, bent to direct the exhaust similarly to the fume dilutors. By redirecting the exhaust, the concentration of C02 measured on the LHD vehicle was reduced by as much as 507, in dead-end headings up to 200 ft long. The Fume Diluters showed no improvement over the simple redesign of the exhaust system.

Jan 1, 1980

By Gary Choate

The work presented in this report represents the background activity which led to the fabrication and testing of a greenhorn and crowd limit switch system for electric shovels. The program began With a literature search and manufacturers product review to gather material as a basis for concept generation. Visits to three open pit mines provided information from operation and maintenance managers which was useful in preparing design concepts. These concepts were evaluated through laboratory tests and engineering analysis to select a final design concept. The resultant greenhorn is four separate shock absorbing pads each enclosed in a housing which bolts to the end of a dipper handle adaptor. The plungers impact against stops mounted to the saddle block. The crowd limit control is a nonmechanical device which senses the location of the dipper and makes appropriate commands to the crowd motor to insure against impacting the greenhorns. The electronic crowd limit control is redundant and indicates malfunction modes. The greenhorn prevents shovel damage in the unlikely event of impact.

Jan 1, 1983

By Thomas E. Finch

This report is a continuation and expansion of a previous USBM grant (No. G0254004) which examined alternative methods of handling the parting between two coal seams in a surface mining operation. The alternative methods consist of equipment implementation in either a stowing or haulback technique. Following a typical strip mine conformation, the parting is directly stowed or hauled back and placed in the pit bottom after second seam removal. The objectives are to produce an environmentally sound material placement technique and to increase prime stripping machine utilization. This report contains the engineering philosophy behind two computer programs created to evaluate parting handling methods over d wide range of coal and parting thickness ratios. The nature of the computer approach allows cost sensitivity analysis and quick updating of costs. The two programs are clearly presented with documentation and examples such that consumers may apply then to their own operations.

Jan 1, 1977

By L. R. Stark

Two wetland simulation experiments were carried out in order to determine the effects on manganese retention of several wetland design parameters, including flow rate, inlet pH, carbon supplementation, substrate type, and surface free water depth. The primary aim in each experiment was to determine if sustained manganese retention could be accomplished under the specific experimental treatments. If successful, these experiments could recommend design parameters for the construction of field wetland systems for manganese treatment. Crushed limestone clearly was superior to spent mushroom compost with respect to manganese retention. The presence of free surface water detracted from manganese treatment, while lower flow rates enhanced manganese treatment. Sustained manganese retention was achieved using crushed limestone as the substrate coupled with an absence of surface free water, under inlet water conditions of pH 7.0 and no appreciable iron. Sustained manganese retention was not achieved under reducing conditions using spent mushroom compost while varying flow rate, inlet pH, and carbon supplementation regimes. However, lowering the flow rate resulted in many significant beneficial effects on outlet water chemistry: lower outlet manganese concentrations (over the short term), higher outlet pH, lower outlet acidity, higher outlet alkalinity, higher outlet sulfide, lower outlet sulfate, and lower outlet redox potential. Supplementation of the wetlands with dairy whey resulted in lower outlet manganese concentrations (over the short term), marginally higher outlet sulfide levels, and acted to lower the redox potential under the high flow regime. Wetlands receiving a neutral pH had lower outlet acidity, higher outlet alkalinity, lower outlet sulfate, but equivalent outlet manganese concentrations than wetlands receiving an acidic pH. When manganese is the primary mine water contaminant and a passive water treatment system is to be used, it is recommended that crushed limestone with negligible surface water be used in place of composted materials. This recommendation assumes a source water with circumneutral pH and an absence of other metals.

Jan 1, 1993

By Tom Retka

This three volume final report summarizes the activities and conclusions of this contract. The objective of the contract was to develop noise control modifications on a retrofit basis, for auger miner coal-cutting systems. Manuals were prepared to assist mine shop personnel in retrofitting the auger miner with these noise controls. Final Report Volume I - Details all vibration and acoustical tests conducted in development of the noise controls. Final Report Volume II - Noise Control Modification Manual for the Jeffrey 100-L Auger Miner describes the various noise control modifications to the auger miner, along with fabrication procedures, cost and vendor information. Final Report Volume III - Noise Control Modification Manual for the Jeffrey 94-L Bridge Conveyor describes the various noise control modifications to the bridge conveyor, along with fabrication procedures, cost and vendor information.

Jan 1, 1978

By T. G. Carnahan

In-place leaching is being actively utilized to extract uranium, copper, and evaporites from low-grade and difficult-to-mine ores. The purpose of this report is to discuss in-place leaching technology, its advantages and disadvantages, and to give an overview of past, current, and envisioned in-place leaching operations in the U.S.A. Application of in-place leaching to uranium ores has been particularly successful because the conditions for leaching are nearly ideal. The ores are generally in highly permeable sandstone aquifers bounded above and below by impermeable shales. The uranium ore minerals are easily leached with oxidizing acid or base solution and the pregnant solutions are amenable to ion exchange concentration and purification prior to conventional solution neutralization for recovery of yellow cake. Copper is routinely recovered from sub-grade rock by dump leaching at most major copper mines. Acidified ferric sulfate is either sprayed on the surface of the dumps or is ponded on top of the dumps. The leaching solution migrates down through the rock and dissolves copper. The solution is collected from the base of the dumps and copper is recovered by solvent extraction-electrowinning or by cementation on detinned steel cans. True in-place copper leaching is being practiced in the caved stopes of an exhausted underground copper mine. Other innovative in-place copper leaching techniques have been tested commercially and laboratory- and pilot-scale experiments have been conducted to investigate proposed in-place leaching techniques for extracting copper from difficult-to-treat chalcopyrite ores. Solution mining of evaporites is being conducted commercially for the extraction of sodium chloride and potassium chloride. A large-scale experimental project for solution mining of trona has been undertaken.

Jan 1, 1982

By J. B. Zadra

Tungsten metal, chemically equivalent to commercial grade, is produced by electrolysis of impure tungsten compounds or scheelite in an alkali, phosphate or borate electrolyte. A preliminary investigation of fused-bath electrolysis shows the effect of electrolyte composition, temperature, and current density on current efficiency, yield, crystal structure, and purity of product. Experiments show that tungsten can be electrowon from scheelite in a fused alkali, phosphate, or borate bath with similar results. Studies on electrolyte composition show that the addition of sodium chloride is essential to both electrolytes in treating scheelite. Although its main function is to react with or flux the CaO, it also increases the bath fluidity. Temperature studies revealed optimum ranges between 900° and 1,100° C.; 900° C. proved satisfactory for tungsten trioxide, and 950° to 1,050° C. for scheelite. Current efficiencies were satisfactory for all current densities ranging from 10 to 57 a./dm.2. Yields were 400 to 650 g./kw.-hr. over the same current-density range. Crystal size and purity of the product are functions of temperature, current density, and amount of impurities in the electrolyte. Deposited crystals vary in shape from spherical grains to clusters of dendritic hexagonal needles, and in size from smaller than 35 to 570 microns. The purity of the tungsten metal produced ranges from 99.7 to 99.94 percent.

Jan 1, 1959

By D. K. Steele

An 18-in-diam column water elutriator was designed, tested, and operated by the Bureau of Mines for recovering nonferrous mixed metals from automobile shredder rejects. The waver elutriator separated metals from nonmetals contained in shredded nonmagnetic rejects. The unit was constructed and integrated into a local automobile shredding operation. Nonmagnetic rejects from the automobile shredder were fed onto the surface of a column of rising water. Dense materials fell through the rising water and were collected as a sink product at the bottom of the column; medium-density materials were removed as an intermediate product in a water flow through a discharge port located between the overflow and sink; and light materials were immediately carried out in the overflowing water at the top of the column as a float product. Nearly 99 pct of the mixed metals were recovered from the nonmagnetic rejects as a 70-pct-metal concentrate. Other operating conditions yielded a 93.7-pct-pure-metal product resulting in a 93.1-pct metal recovery. Float rejects are combustibles, light plastics, foam rubber, and minimal amounts of coated and uncoated copper wire. The middling discharge contained mainly medium-density rubber, plastics, glass, rock, coated and uncoated copper wire, and frequently some thin-sheet stainless steel and wrought aluminum. Maximum metal recovery in the operating program was achieved using a water velocity of 52 fpm (650 gpm). Maximum purity was obtained with a velocity of 88 fpm (1,100 gpm). .Water was recycled through a 12,000-gal baffled clarifying tank. Entrainment water losses with the float and middling rejects averaged 50 gpt of reject feed. Records maintained by the shredder operator show a 34-pct increase in nonmagnetic metals recovery during a 1-yr operation of the water elutriator as compared to recoveries from a previously used air classification system.

Jan 1, 1983

The above referenced contract between Badger Manufacturing Corporation and the U. S Bureau of Mines was executed June 30, 1975, as a result of the request for proposals for innovative machine concepts. We selected the cutting machine category because of the obvious lack of technical progress in this field for many years: Phase I of the contract required blasting fragmentation tests to determine proper blasting patterns for use with the auger-type kerf cutting machine. Phase II required design concept development for a machine capable of cutting a circular void as an aid to blasting.

Jan 1, 1975

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the U.S. Department of the Interior, Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows were continuous except for short periods when resin increments were withdrawn. The exchange of uranyl carbonate between a simulated in situ uranium leach liquor and a strong-base ion-exchange resin together with the subsequent elution with an ammonium chloride solution was studied. The effects of the number of sections, section height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. The kinetic and equilibrium relationships for the absorption and elution steps were also examined. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

Mining and the related extractive and processing industries are chiefly responsible for America's high standard of living. Enormous quantities of sand and gravel, limestone, copper, iron and a myriad of other mineral commodities are required to sustain our growing nation. However, the mineral deposits, both domestic and foreign, are becoming increasingly difficult to find. Adding substantially to the problem, is the fact that the conditions are worldwide. Foreign politics are increasingly affecting mineral commodity availability. Figure 1, taken from Bureau of Mines, "Status of the Mineral industries 1976" illustrates our dependency (in some cases total) on foreign sources for vital mineral commodities. While few nations are capable of exerting an OPEC-like influence on any one mineral commodity, the threat of cartel arrangements and related control strategies is evident. Nationalization of entire industries, once they become self-sufficient, is also exerting a disruptive influence on a large portion of the mineral industries.

Jan 1, 1977

By Robert A. Harrow

This report documents the results of the development and installation of an illumination system for an underground coal mine Shortwall Mining Section. Also presented are the techniques used for the above ground test and evaluation of the lighting system prior to installation underground which resulted in the issuance of a Statement of Test and Evaluation (STE) from the Mine Safety and Health Administration, Technical Support, Beckley, West Virginia.

Jan 1, 1979

This report summarizes the results of the Narragansett Win Projec't's activities during the U.S. Bureau of Mines (BOM) Phase 1, which was transitional from and which followed the National Science Foundation (NSF) Phase which initiated the investigation of New England's potential roil resource. The 960 sq. mile basin is structural and topographic lowland containing 12,000 to 20,000 ft. of terrigenous clastic sediments of late Pennsylvanian age, and which rests on an upper Precambrian and Cambrian basement. The Rhode Island Formation, which is the coal-bearing unit, comprising the bulk of the Pennsylvanian rocks consists, in order of decreasing abundance, of sandstone, conglomerate, silts tone, shale, and coal. In the NSF Phase, 24 drill-holes yielded 17,900 ft, of core; in the BOM Phase I study, 4 drillholes yielded 2,100 ft. of core. Anthracite and semi-anthracite was encountered in beds Up to 30 ft. thick in widely spaced parts of the Basin. The coal, typically very low in sulfur, and a high ash anthracite, won mined in substantial volumes from 1808 to 1959 from shaft and open lit in Portsmouth and Cranston, R.I., and in lesser volumes in Mansfield, Mass. Currently coal is now being mined in Plainville, Mass. as a fuel in the manufacturing of light-weight aggregate from the same quarry that serves as the source of the rock being processed. The structurally complex Narragansett Basin is now known to have a greater extent than earlier since recent drilling by others (Chapter 2) has confirmed our interpretation that the Basin extended offshore south A Boston. The, Basin also extends into Rhode Island Sound to the south. The geological structure is more complex in the southern part of the Basin than in the northern part. Three episodes of folding have been documented on Aquidneck Island and four episodes of faulting have been demonstrated for the Basin as a whole. Relatively less well exposed rock in the northern part of the Basin, increases the difficulty of recognizing and correlating structural episodes in the northern part of the Basin. The Basin his hewn subdivided into six structural domains which appear to have distinctive structural, metamorphic, paleontological and sedimentological differences that mw assist in isolating important events in the evolution of the Basin and its component parts. The tentative structural model recently developed in POP Phase I has important implications for exploration and mining. In the first and second folding stages the coal is mobilized and thickened in the crests and troughs of folds whose axes are horizontal to subhorizontal. While conventional coal exploration and mining methods are not applicable, great thickening in the crests and troughs of large scale structures, which can he defined by geology, geophysics and drilling, may provide compensating advantages. Bedrock over most of the Basin is 0-50 ft., but thicknesses of glacial deposits up to 150 ft. are present locally. Pro-Pleistocene topographic trends are controlled by structure and rock hardness; Pleistocene deposits aligned to the S. F. are superimposed on earlier trends. The southern part of the Basin is mainly dominated by high grade Barrovian metamorphism and plutonism of Permian age, related to the Alleghanian Orogeny. About 300 sq. miles of the 960 sq. mile Basin has been affected. The remaining 660 sq. miles, in the chlorite and subchlorite zones of metamorphism are compatible with the presence of high quality anthracite and semi-anthracite. Illite crystallinity studies begun in the NSF Phase, have been carried out in the BOM Phase l with important results. About ME of the northern Basin is now known to be in the diagenetic (unmetamorphosed) or subchlorite zone and the remainder in the chlorite zone of metamorphism. Mite studies, probably best recording temperature effects, show a generally progressive increase from the NW corner of the Basin near Plainville, Mass. toward the south and southeast. Reflectivity and coal petrography studies, probably best recording pressure and effects related to shearing, indicate a generally opposite pattern. Thus these methods provide powerful tools for the ultimate solution of problems important to coal exploration for coals of higher combustible volatile content and exploitation of these. Due to the complex nature of the coal, chemical data may not he easily used to determine rank. The coals have been tectonically deformed and mineralized. This deformation plus thermal metamorphism have altered the coals, in some cases by producing natural coke. Brecciated coal is often coated with a secondary depositional carbon. The coals' hydroscopic nature and high ash contents are due to the deformed nature of the coal and the presence of this secondary carbon. The stratigraphy and sedimentology of the coal-bearing Rhode Island Formation is similar to described alluvial fan deposits. The non-geological studies al-low three conclusions to be made: 1. A substantial number of areas have been identified in the Narragansett Basin in which mining could be carried out without undue difficulty from a land use point of view. 2. Substantially more than two hundred instances of past or current- mining activities have been identified in the Basin. Many of those are in areas defined as geologically interesting, and may be advantageous From the point of view of future exploration. 3. The map synthesis technique developed for this contract is successful and may easily be adapted to future exploration in its current form and also in its expandable form dealing with unit measurements of one-tenth mile. We recommend that BOM Phase 2 exploration should accomplish the intent of the Congressional language in House Report No. 95-1251, to continue a substantial drilling and geophysics program: "The Committee expects the Bureau to continue studies involved in ascertaining the extent and quality of low sulfur coal reserves in the Narragansett Basin in New England including necessary drilling and geophysical studies. The knowledge of the extent of such deposits is of great importance to this 'energy pour' area".

Jan 1, 1979

By Charles H. Etheridge

A new filter cassette is described which can be used with Coal Mine Dust Personal Sampler Units (CFR, Title 30, Part 74). The sealed cassette design reduces the chances of sample loss due to reverse flushing, impact or cassette opening. The filter capsule weight is approximately 400 milligrams and is stable for at least one year in storage. The alpha quartz content of the filter element is less than 5 nanograms per square millimeter of surface. The cassette is designed to be used with a new sampling head. The manufacturing costs of the new cassette will require an increase of approximately 30% in the selling price.

Jan 1, 1978

By P. R. Tisot

Structural response and/or deformation was determined for each of four different grade Green River oil shales (27.0-, 34.5-, 45.5-, and 63.5-gal/ton) as they were heated in an inert atmosphere, under constant compressive stress, from ambient to subretorting temperatures; that is, below those required for rapid pyrolysis of the organic matter. Small cores and small columns of confined fragments comprised the test specimens, which were heated, in a specially designed microunit, at a uniform rate either to 725° or to 825° F under three different stress levels, 80, 200, and 325 psi. Structural response of some cores was observed as they were heated in a stress-free environment. The obtained stress-strain-time-temperature relationships provide information regarding the oil shale's yield temperature, yield stress, rate of compressive strain, loss of mechanical strength, and nature of structural deformation. Effects of structural deformation on induced permeability in small columns of fragments are presented. Results indicate that underground retorting of Green River oil shale may be seriously impaired through loss of induced permeability brought about by structural deformation of rich oil shale under the influence of heat and compressive stress.

Jan 1, 1971

By J. B. Czirr

MESA Corporation has completed a four-year program for the Bureau of Mines to develop a technique for measuring roof competence in underground coal mines. The preferred technique employs a tracer gas that is injected into a roof borehole drilled near the working face. The tracer gas performs the dual purpose of determining the pressure loss rate from the borehole and of marking the diffusion pattern of the the escaping gas. The primary detection technique relies upon observation of the rate of pressure drop in a hole drilled in the roof strata under test. If this measurement indicates a significant probability of roof collapse, the gas diffusion pattern is outlined with the Leak-gun tracer-gas detector. These two techniques provide a comprehensive method for predicting the relative probability of roof collapse in operating coal mines.

Jan 1, 1985

By Arnold O. Tanner

Tables based on 1985 data, which were not available in time for publication of the "1985 Minerals Yearbook," are included in this chapter; corresponding tables for 1986 are not yet available. Raw nonfuel minerals produced in the United States during 1986 had an estimated value of $23.5 billion, an increase of $0.25 billion over the 1985 value. This is the fourth consecutive year that the value has increased, and except for a de- crease in 1982, the value each year has increased since 1971, or 14 out of 15 years. Industrial minerals growth slowed from a 3% increase in value in 1985 to a 1.5% increase in 1986, reflecting the slow growth in the domestic economy. The value of industrial minerals, more than three times larger than the value of metals, easily offset the less than 0.5% decline in the value of metal mine production. Although the decline was small, this decrease makes 1986 the fourth year in the past 6 years in which a drop in the value of metal mining production occurred in the United States. U.S. production continued to lag behind the growing world production. Overall, the estimated raw nonfuel mineral production rose 1% over that of 1985. Domestic mine production of ferrous metals declined as follows, in decreasing order of production: nickel, iron ore, tungsten, and molybdenum. All remaining domestic primary nickel and tungsten mines had closed down by yearend. Nonferrous metals that similarly declined included titanium, rare-earth metals, lead, silver, zinc, and magnesium. For the second consecutive year, aluminum, produced predominantly from imported bauxite, declined in production, while imports reached record-high levels. Somewhat modest gains were made in beryllium and copper. As has been the case for a number of years, gold was a bright spot in the domestic and internation-al metal mining industry. Gold production was spurred on by the increasing usage and development of heapleaching techniques that make lower grade ores, which were previously uneconomical, profitable. Additionally, various mining companies, the U.S. Mint, individual States, and a number of foreign countries began production of gold bullion and commemorative coins. Gold output in the United States increased from 2.43 million troy ounces (revised) in 1985 to about 3.73 million troy ounces in 1986, a dramatic 54% rise.

Jan 1, 1988

The principal activities of the Bureau of Mines Explosives Research Center during fiscal year 1969 (July 1: 1968, to June 30, 1969) are reviewed in part 1. Part 2 presents short abstracts of the publications issued during this period in the Bureau series and in the outside press. These publications are referenced in part 1 by underlined numbers in parentheses. Other publications, which are not abstracted, are cited in footnotes throughout the paper. ACKNOWLEDGEMENTS The Bureau acknowledges the support received through cooperative agreement in fiscal year 1969 from the Manufacturing Chemists Association. It also acknowledges the sponsorship by the following Government agencies of research conducted during that period: Department of the Air Force, Department of the Army, Department of Health, Education, and Welfare, Department of the Navy, Federal Aviation Administration, National Aeronautics and Space Administration, Space Nuclear Propulsion Office, and United States Coast Guard.

Jan 1, 1970

By David J. Kusler

This Bureau of Mines study is an appraisal of the demand for platinum, should this strategic metal be used as a. catalyst in the National abatement of automobile exhaust pollution. The Clean Air Act 0f 1970, as amended, requires that automobiles produced in 1975 and thereafter be provided with antipollutive measures to control automotive exhaust emissions. The study considers the need for automobile pollution control, the methodology for such control, the annual primary (new) platinum demand for automobiles produced from 1975 to 1990, primary platinum availability, and supply-demand forecasts and outlook. The correlative demand for platinum for the production of the required unleaded gasoline is also considered. Methodology for the study included a forecast of new automobile production from 1975 to 1990, development of automobile survival and retirement data, estimates of new platinum demand under various conditions of salvage, and data on recycling the precious metal from the catalytic converters of scrapped vehicles and existing vehicles when their spent converters are exchanged for replacement units. The new platinum demand for automobile exhaust converters, based on a converter service life of 50,000 miles, is estimated to be 1.41 million troy ounces initially in 1975, rising to 1.68 million in 1980, and declining curvi-linearly to 0.94 million in 1990. The platinum demand for converter longevities other than 50,000 miles can be derived from the tabular data presented. An appendix to the report presents a comparison between longevities of 50,000 miles and 25,000 miles. The petroleum industry's demand for new platinum for the production of lead-free gasolines could total as high as 1 million troy ounces between 1972 and 1981, just for expansion of isomerization and reforming capacity, and is in addition to normal operating demand for this metal.

Jan 1, 1972